U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################# 4 MiB/s done Bytes transferred = 7100312 (6c5798 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66405 (10365 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x6c5798 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83013364 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.8.0-rc8-111539-g08895a8 (pwalmsley@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Sun Sep 25 19:05:05 PDT 2016 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt:Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c141d380, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 14 pages/cpu @eef85000 s25984 r8192 d23168 u57344 [ 0.000000] pcpu-alloc: s25984 r8192 d23168 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1994972K/2096128K available (9216K kernel code, 1148K rwdata, 3972K rodata, 2048K init, 343K bss, 35620K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0c00000 (10208 kB) [ 0.000000] .init : 0xc1100000 - 0xc1300000 (2048 kB) [ 0.000000] .data : 0xc1300000 - 0xc141f200 (1149 kB) [ 0.000000] .bss : 0xc1421000 - 0xc1476c48 ( 344 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000031] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000045] Switching to timer-based delay loop, resolution 1000ns [ 0.005332] arm_arch_timer: Architected cp15 timer(s) running at 12.00MHz (virt). [ 0.005350] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005368] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005380] Switching to timer-based delay loop, resolution 83ns [ 0.005803] Console: colour dummy device 80x30 [ 0.005831] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=60000) [ 0.005845] pid_max: default: 32768 minimum: 301 [ 0.005937] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005948] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006543] CPU: Testing write buffer coherency: ok [ 0.006762] /cpus/cpu@0 missing clock-frequency property [ 0.006803] /cpus/cpu@1 missing clock-frequency property [ 0.006844] /cpus/cpu@2 missing clock-frequency property [ 0.006886] /cpus/cpu@3 missing clock-frequency property [ 0.006898] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006920] Setting up static identity map for 0x80300000 - 0x80300098 [ 0.010568] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011938] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015632] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.020627] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.025164] Brought up 4 CPUs [ 0.025184] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.025191] CPU: All CPU(s) started in SVC mode. [ 0.026649] devtmpfs: initialized [ 0.046936] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.047375] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.048718] pinctrl core: initialized pinctrl subsystem [ 0.050475] NET: Registered protocol family 16 [ 0.052407] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.065284] cpuidle: using governor menu [ 0.084095] No ATAGs? [ 0.084122] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.084132] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.090415] Serial: AMBA PL011 UART driver [ 0.125381] +5V_SYS: supplied by +VDD_MUX [ 0.125706] +3.3V_SYS: supplied by +VDD_MUX [ 0.126335] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.126351] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.126439] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.126452] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.126613] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.126625] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.126708] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.126720] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.126802] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.126814] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.126895] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.126907] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.130185] vgaarb: loaded [ 0.131035] SCSI subsystem initialized [ 0.131200] libata version 3.00 loaded. [ 0.131480] usbcore: registered new interface driver usbfs [ 0.131548] usbcore: registered new interface driver hub [ 0.131611] usbcore: registered new device driver usb [ 0.135224] pps_core: LinuxPPS API ver. 1 registered [ 0.135233] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.135256] PTP clock support registered [ 0.135454] EDAC MC: Ver: 3.0.0 [ 0.138660] clocksource: Switched to clocksource arch_sys_counter [ 0.149946] NET: Registered protocol family 2 [ 0.150460] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.150558] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.150744] TCP: Hash tables configured (established 8192 bind 8192) [ 0.150794] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.150835] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.150989] NET: Registered protocol family 1 [ 0.151323] RPC: Registered named UNIX socket transport module. [ 0.151332] RPC: Registered udp transport module. [ 0.151339] RPC: Registered tcp transport module. [ 0.151347] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.151357] PCI: CLS 0 bytes, default 64 [ 0.152538] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.154056] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.154775] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.165976] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.166831] NFS: Registering the id_resolver key type [ 0.166855] Key type id_resolver registered [ 0.166863] Key type id_legacy registered [ 0.166905] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.168158] bounce: pool size: 64 pages [ 0.168367] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.168377] io scheduler noop registered [ 0.168385] io scheduler deadline registered [ 0.168590] io scheduler cfq registered (default) [ 0.174359] usb2-0 supply vbus not found, using dummy regulator [ 0.174489] usb2-1 supply vbus not found, using dummy regulator [ 0.174885] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.175596] libphy: mdio_driver_register: phy-bcm-ns2-pci [ 0.191866] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 0.191919] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 0.199191] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.201167] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.267456] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.270449] console [ttyS0] disabled [ 0.270484] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.128525] console [ttyS0] enabled [ 1.133019] SuperH (H)SCI(F) driver initialized [ 1.138631] msm_serial: driver initialized [ 1.142945] STMicroelectronics ASC driver initialized [ 1.148894] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.158227] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.170653] [drm] Initialized drm 1.1.0 20060810 [ 1.178525] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.198165] brd: module loaded [ 1.207197] loop: module loaded [ 1.210807] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.219130] as3722 4-0040: AS3722 with revision 0x1 found [ 1.230261] as3722-sd2: supplied by +5V_SYS [ 1.234962] as3722-sd3: supplied by +5V_SYS [ 1.239391] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.245772] as3722-sd4: supplied by +5V_SYS [ 1.250426] as3722-sd5: supplied by +5V_SYS [ 1.256517] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.262615] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.268890] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.274813] as3722-ldo3: supplied by +3.3V_SYS [ 1.279310] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.287125] as3722-ldo4: supplied by +3.3V_SYS [ 1.291800] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.298063] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.302911] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.309882] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.315553] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.321744] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.334213] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.354159] random: fast init done [ 1.357716] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.366196] libphy: Fixed MDIO Bus: probed [ 1.371147] CAN device driver interface [ 1.377316] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.384284] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.393390] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.400847] usbcore: registered new interface driver pegasus [ 1.406579] usbcore: registered new interface driver asix [ 1.412032] usbcore: registered new interface driver ax88179_178a [ 1.418176] usbcore: registered new interface driver cdc_ether [ 1.424078] usbcore: registered new interface driver smsc75xx [ 1.429894] usbcore: registered new interface driver smsc95xx [ 1.435691] usbcore: registered new interface driver net1080 [ 1.441400] usbcore: registered new interface driver cdc_subset [ 1.447368] usbcore: registered new interface driver zaurus [ 1.453017] usbcore: registered new interface driver cdc_ncm [ 1.458913] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.466362] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.472901] ehci-pci: EHCI PCI platform driver [ 1.477397] ehci-platform: EHCI generic platform driver [ 1.482859] ehci-orion: EHCI orion driver [ 1.487038] SPEAr-ehci: EHCI SPEAr driver [ 1.491225] ehci-st: EHCI STMicroelectronics driver [ 1.496270] ehci-exynos: EHCI EXYNOS driver [ 1.500637] ehci-atmel: EHCI Atmel driver [ 1.504810] tegra-ehci: Tegra EHCI driver [ 1.511664] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.517100] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.524840] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.543684] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.550427] hub 1-0:1.0: USB hub found [ 1.554236] hub 1-0:1.0: 1 port detected [ 1.558778] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.564974] ohci-pci: OHCI PCI platform driver [ 1.569479] ohci-platform: OHCI generic platform driver [ 1.574891] ohci-omap3: OHCI OMAP3 driver [ 1.579066] SPEAr-ohci: OHCI SPEAr driver [ 1.583228] ohci-st: OHCI STMicroelectronics driver [ 1.588266] ohci-atmel: OHCI Atmel driver [ 1.593115] usbcore: registered new interface driver usb-storage [ 1.600786] mousedev: PS/2 mouse device common for all mice [ 1.609785] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.616675] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.625049] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.632243] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.639030] i2c /dev entries driver [ 1.649723] 0-004c supply vcc not found, using dummy regulator [ 1.665423] sdhci: Secure Digital Host Controller Interface driver [ 1.671617] sdhci: Copyright(c) Pierre Ossman [ 1.677671] Synopsys Designware Multimedia Card Interface Driver [ 1.684889] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.691361] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.696270] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.701404] mmc0: Unknown controller version (3). You may experience problems. [ 1.708739] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.758684] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.768753] ledtrig-cpu: registered to indicate activity on CPUs [ 1.775117] usbcore: registered new interface driver usbhid [ 1.780701] usbhid: USB HID core driver [ 1.789425] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 1.806813] NET: Registered protocol family 10 [ 1.812184] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.818820] NET: Registered protocol family 17 [ 1.823266] can: controller area network core (rev 20120528 abi 9) [ 1.829532] NET: Registered protocol family 29 [ 1.833998] can: raw protocol (rev 20120528) [ 1.838261] can: broadcast manager protocol (rev 20160617 t) [ 1.843944] can: netlink gateway (rev 20130117) max_hops=1 [ 1.849810] Key type dns_resolver registered [ 1.854715] ThumbEE CPU extension supported. [ 1.859008] Registering SWP/SWPB emulation handler [ 1.866869] +3.3V_RUN: supplied by +3.3V_SYS [ 1.872256] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.878392] +USB0_VBUS_SW: supplied by +5V_SYS [ 1.883501] +5V_USB_HS: supplied by +5V_SYS [ 1.889448] +3.3V_LP0: supplied by +3.3V_SYS [ 1.895914] +5V_HDMI_CON: supplied by +5V_SYS [ 1.901007] +5V_SATA: supplied by +5V_SYS [ 1.905721] +12V_SATA: supplied by +VDD_MUX [ 1.912016] usb2-0 supply vbus not found, using dummy regulator [ 1.915020] mmc0: new high speed MMC card at address 0001 [ 1.916561] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 1.917690] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 1.918936] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 1.919739] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 1.925566] mmcblk0: p1 [ 1.948392] usb2-1 supply vbus not found, using dummy regulator [ 1.954763] usb3-0 supply vbus not found, using dummy regulator [ 1.961994] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 1.968633] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 1.978499] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 1.989317] as3722-sd2: supplied by +5V_SYS [ 1.993950] as3722-sd3: supplied by +5V_SYS [ 1.998484] as3722-sd4: supplied by +5V_SYS [ 2.003008] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.008799] as3722-sd5: supplied by +5V_SYS [ 2.014772] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.020855] as3722-ldo1: supplied by +3.3V_RUN [ 2.025748] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.031360] as3722-ldo3: supplied by +3.3V_SYS [ 2.036815] as3722-ldo4: supplied by +3.3V_SYS [ 2.041541] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.046428] as3722-ldo6: supplied by +3.3V_RUN [ 2.051166] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.056541] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.063633] as3722-ldo9: supplied by +5V_SYS [ 2.069140] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.075751] as3722-ldo10: supplied by +5V_SYS [ 2.080646] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.087479] as3722-ldo11: supplied by +3.3V_RUN [ 2.092803] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.102770] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.111847] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.122723] scsi host0: tegra-ahci [ 2.127395] scsi host1: tegra-ahci [ 2.131188] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.139202] ata2: DUMMY [ 2.144772] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.150209] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.157959] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.178783] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.185886] hub 2-0:1.0: USB hub found [ 2.189741] hub 2-0:1.0: 1 port detected [ 2.196209] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.201161] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.206296] mmc1: Unknown controller version (3). You may experience problems. [ 2.213626] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.264258] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA 64-bit [ 2.276862] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.285633] tegra-pcie 1003000.pcie-controller: probing port 0, using 2 lanes [ 2.294973] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000008 [ 2.318030] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 2.327315] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000000 [ 2.342344] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.349607] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.355854] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.362794] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.370170] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.375759] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.381936] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.388957] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.395121] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.402184] PCI: bus0: Fast back to back transfers disabled [ 2.407828] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.415912] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.424264] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.430376] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.437431] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.458817] PCI: bus1: Fast back to back transfers disabled [ 2.462023] ata1: SATA link down (SStatus 0 SControl 300) [ 2.469914] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.476849] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.482958] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.488638] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.495524] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.502963] pci 0000:02:00.0: supports D1 D2 [ 2.507287] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.528809] PCI: bus2: Fast back to back transfers disabled [ 2.534465] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.541357] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.548244] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.555125] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.562969] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.569162] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.576585] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.581651] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.588549] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.596408] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.603831] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.610024] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.615074] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.621255] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.621357] mmc1: new high speed SDHC card at address aaaa [ 2.622798] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.638168] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.646003] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.653160] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.659628] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 2.666669] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.673278] pcie_pme 0000:00:01.0:pcie001: service driver pcie_pme loaded [ 2.680271] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.687428] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.693936] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.700978] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.707587] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded [ 2.714823] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.720489] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.728188] mmcblk1: p1 p2 p3 [ 2.740523] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0a5a000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 2.750230] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.762572] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.769248] [drm] No driver support for vblank timestamp query. [ 2.900542] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.067980] Console: switching to colour frame buffer device 512x135 [ 3.164031] drm drm: fb0: frame buffer device [ 3.183771] [drm] Initialized tegra 0.0.0 20120330 on minor 0 [ 3.191127] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 3.199214] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.206579] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.216130] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.223317] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:12 UTC (946684812) [ 3.236136] +USB0_VBUS_SW: disabling [ 3.239739] +1.8V_RUN_CAM: disabling [ 3.243571] +2.8V_RUN_CAM: disabling [ 3.247432] +1.2V_RUN_CAM_FRONT: disabling [ 3.251814] +1.05V_RUN_CAM_REAR: disabling [ 3.256113] +3.3V_RUN_TOUCH: disabling [ 3.260060] +2.8V_RUN_CAM_AF: disabling [ 3.264093] +1.8V_RUN_VPP_FUSE: disabling [ 3.269633] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.312384] EXT4-fs (mmcblk0p1): recovery complete [ 3.318066] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.326211] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.336536] devtmpfs: mounted [ 3.340626] Freeing unused kernel memory: 2048K (c1100000 - c1300000) bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#