U-Boot 2015.04-00466-gedec83e90172 (Mar 14 2016 - 10:42:01) TEGRA124 Model: Acer Chromebook 13 CB5-311 DRAM: 4 GiB : Tegra SD/MMC: 0, Tegra SD/MMC: 1, Tegra SD/MMC: 2 MMC init failed Using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Nyan-big) # Tegra124 (Nyan-big) # usb start starting USB... USB0: USB EHCI 1.10 scanning bus 0 for devices... 2 USB Device(s) found USB1: USB EHCI 1.10 scanning bus 1 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... Warning: asx0 using MAC address from net device 1 Ethernet Device(s) found Tegra124 (Nyan-big) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=4d36e82a-b3c0-4b4b-bfcd-afe5217ac023 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Nyan-big) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Nyan-big) # tftpboot 0x82000000 zImage.multi_v7_defconfig Using asx0 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################### 2.8 MiB/s done Bytes transferred = 7238568 (6e73a8 hex) Tegra124 (Nyan-big) # tftpboot 0x83000000 tegra124-nyan-big.dtb Using asx0 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-nyan-big.dtb'. Load address: 0x83000000 Loading: *##### 2.8 MiB/s done Bytes transferred = 66901 (10555 hex) Tegra124 (Nyan-big) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x6e73a8 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83013554 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.7.0-97079-g523d939 (pwalmsley@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Sun Jul 24 13:04:08 PDT 2016 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: Acer Chromebook 13 CB5-311 [ 0.000000] Ignoring memory range 0x100000000 - 0x17ffff000 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524287 [ 0.000000] free_area_init_node: node 0, pgdat c141bb40, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327679 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 13 pages/cpu @eef89000 s23808 r8192 d21248 u53248 [ 0.000000] pcpu-alloc: s23808 r8192 d21248 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522751 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=4d36e82a-b3c0-4b4b-bfcd-afe5217ac023 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1996016K/2097148K available (9529K kernel code, 1142K rwdata, 4476K rodata, 2048K init, 343K bss, 35596K reserved, 65536K cma-reserved, 1245180K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc10ad564 (14998 kB) [ 0.000000] .init : 0xc1100000 - 0xc1300000 (2048 kB) [ 0.000000] .data : 0xc1300000 - 0xc141dba0 (1143 kB) [ 0.000000] .bss : 0xc141f000 - 0xc1474ce0 ( 344 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@0,50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000003] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000012] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000017] Switching to timer-based delay loop, resolution 1000ns [ 0.001791] Architected cp15 timer(s) running at 12.00MHz (virt). [ 0.001798] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.001804] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.001808] Switching to timer-based delay loop, resolution 83ns [ 0.002007] Console: colour dummy device 80x30 [ 0.002021] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=60000) [ 0.002027] pid_max: default: 32768 minimum: 301 [ 0.002066] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002070] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002315] CPU: Testing write buffer coherency: ok [ 0.002427] /cpus/cpu@0 missing clock-frequency property [ 0.002442] /cpus/cpu@1 missing clock-frequency property [ 0.002456] /cpus/cpu@2 missing clock-frequency property [ 0.002470] /cpus/cpu@3 missing clock-frequency property [ 0.002475] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002485] Setting up static identity map for 0x80300000 - 0x80300098 [ 0.003769] Tegra Revision: A01 SKU: 131 CPU Process: 1 SoC Process: 1 [ 0.004373] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.006968] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.011964] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.016688] Brought up 4 CPUs [ 0.016695] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.016698] CPU: All CPU(s) started in SVC mode. [ 0.017238] devtmpfs: initialized [ 0.023600] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023873] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.024403] pinctrl core: initialized pinctrl subsystem [ 0.025067] NET: Registered protocol family 16 [ 0.025739] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.036721] cpuidle: using governor menu [ 0.043147] No ATAGs? [ 0.043159] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.043163] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.045262] Serial: AMBA PL011 UART driver [ 0.046223] tegra-mc 70019000.memory-controller: no memory timings for RAM code 0 registered [ 0.063452] +5V_SYS: supplied by +VDD_MUX [ 0.063560] +3.3V_SYS: supplied by +VDD_MUX [ 0.063782] +VDD_LED: Failed to request enable GPIO122: -517 [ 0.063787] reg-fixed-voltage regulators:regulator@5: Failed to register regulator: -517 [ 0.063818] +5V_VDD_TS_SW: Failed to request enable GPIO81: -517 [ 0.063822] reg-fixed-voltage regulators:regulator@6: Failed to register regulator: -517 [ 0.063852] +5V_USB_HS: Failed to request enable GPIO108: -517 [ 0.063855] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.063885] +5V_USB_SS: Failed to request enable GPIO109: -517 [ 0.063889] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.063968] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.063972] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.064000] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.064004] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.065128] vgaarb: loaded [ 0.065414] SCSI subsystem initialized [ 0.065478] libata version 3.00 loaded. [ 0.065580] usbcore: registered new interface driver usbfs [ 0.065603] usbcore: registered new interface driver hub [ 0.065628] usbcore: registered new device driver usb [ 0.067013] pps_core: LinuxPPS API ver. 1 registered [ 0.067017] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.067025] PTP clock support registered [ 0.067096] EDAC MC: Ver: 3.0.0 [ 0.067528] tegra-emc 7001b000.emc: no memory timings for RAM code 0 found in DT [ 0.067537] tegra-emc: probe of 7001b000.emc failed with error -2 [ 0.068017] clocksource: Switched to clocksource arch_sys_counter [ 0.071664] NET: Registered protocol family 2 [ 0.071875] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.071908] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.071971] TCP: Hash tables configured (established 8192 bind 8192) [ 0.071994] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.072009] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.072069] NET: Registered protocol family 1 [ 0.072170] RPC: Registered named UNIX socket transport module. [ 0.072174] RPC: Registered udp transport module. [ 0.072176] RPC: Registered tcp transport module. [ 0.072179] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.072183] PCI: CLS 0 bytes, default 64 [ 0.072619] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.073177] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.073459] workingset: timestamp_bits=28 max_order=19 bucket_order=0 [ 0.077266] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.077575] NFS: Registering the id_resolver key type [ 0.077589] Key type id_resolver registered [ 0.077592] Key type id_legacy registered [ 0.077609] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.078096] bounce: pool size: 64 pages [ 0.078171] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.078175] io scheduler noop registered [ 0.078178] io scheduler deadline registered [ 0.078189] io scheduler cfq registered (default) [ 0.080091] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.088925] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.089617] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.110878] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.112026] console [ttyS0] disabled [ 0.112042] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 331, base_baud = 25500000) is a Tegra [ 0.964691] console [ttyS0] enabled [ 0.968488] SuperH (H)SCI(F) driver initialized [ 0.973374] msm_serial: driver initialized [ 0.977522] STMicroelectronics ASC driver initialized [ 0.984006] [drm] Initialized drm 1.1.0 20060810 [ 0.990028] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 0.996582] tegra-dpaux 545c0000.dpaux: failed to get VDD supply: -517 [ 1.003803] panel supply power not found, using dummy regulator [ 1.013547] brd: module loaded [ 1.018707] loop: module loaded [ 1.022745] as3722 4-0040: AS3722 with revision 0x1 found [ 1.032461] as3722-sd2: supplied by +5V_SYS [ 1.036886] as3722-sd3: supplied by +5V_SYS [ 1.041226] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.047408] as3722-sd4: supplied by +5V_SYS [ 1.051743] +1.05V_RUN: Bringing 0uV into 1050000-1050000uV [ 1.057488] as3722-sd5: supplied by +5V_SYS [ 1.063086] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.068820] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.074848] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.080469] as3722-ldo3: supplied by +3.3V_SYS [ 1.084919] +1.00V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.092496] as3722-ldo4: supplied by +3.3V_SYS [ 1.097092] +3.3V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.103120] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.107881] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.114575] +VDDIO_SDMMC3: Bringing 0uV into 1800000-1800000uV [ 1.120610] as3722-ldo7: supplied by +1.8V_VDDIO [ 1.125378] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 1.131941] as3722-ldo9: supplied by +5V_SYS [ 1.136505] +2.8V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 1.142713] as3722-ldo10: supplied by +5V_SYS [ 1.147221] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 1.153672] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 1.171924] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.178199] libphy: Fixed MDIO Bus: probed [ 1.182522] CAN device driver interface [ 1.187069] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.194019] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.200744] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.208155] usbcore: registered new interface driver pegasus [ 1.213825] usbcore: registered new interface driver asix [ 1.219228] usbcore: registered new interface driver ax88179_178a [ 1.225325] usbcore: registered new interface driver cdc_ether [ 1.231168] usbcore: registered new interface driver smsc75xx [ 1.236924] usbcore: registered new interface driver smsc95xx [ 1.242673] usbcore: registered new interface driver net1080 [ 1.248339] usbcore: registered new interface driver cdc_subset [ 1.254263] usbcore: registered new interface driver zaurus [ 1.259852] usbcore: registered new interface driver cdc_ncm [ 1.266221] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.272738] ehci-pci: EHCI PCI platform driver [ 1.277187] ehci-platform: EHCI generic platform driver [ 1.282478] ehci-omap: OMAP-EHCI Host Controller driver [ 1.287744] ehci-orion: EHCI orion driver [ 1.291797] SPEAr-ehci: EHCI SPEAr driver [ 1.295854] ehci-st: EHCI STMicroelectronics driver [ 1.300776] ehci-exynos: EHCI EXYNOS driver [ 1.305009] ehci-atmel: EHCI Atmel driver [ 1.309063] tegra-ehci: Tegra EHCI driver [ 1.313132] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.319305] ohci-pci: OHCI PCI platform driver [ 1.323756] ohci-platform: OHCI generic platform driver [ 1.329029] ohci-omap3: OHCI OMAP3 driver [ 1.333081] SPEAr-ohci: OHCI SPEAr driver [ 1.337129] ohci-st: OHCI STMicroelectronics driver [ 1.342049] ohci-atmel: OHCI Atmel driver [ 1.346324] usbcore: registered new interface driver usb-storage [ 1.352918] mousedev: PS/2 mouse device common for all mice [ 1.358894] 1-0015 supply vcc not found, using dummy regulator [ 1.360709] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.360712] as3722-rtc as3722-rtc: RTC interrupt 370 [ 1.362974] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.362998] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.363294] i2c /dev entries driver [ 1.366639] 0-004c supply vcc not found, using dummy regulator [ 1.376547] sdhci: Secure Digital Host Controller Interface driver [ 1.376552] sdhci: Copyright(c) Pierre Ossman [ 1.377294] Synopsys Designware Multimedia Card Interface Driver [ 1.377850] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.378241] sdhci-tegra 700b0000.sdhci: allocated mmc-pwrseq [ 1.378264] mmc0: Unknown controller version (3). You may experience problems. [ 1.378474] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.378482] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.378515] mmc0: Unknown controller version (3). You may experience problems. [ 1.378666] mmc0: Unknown controller version (3). You may experience problems. [ 1.378711] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.413026] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.413834] ledtrig-cpu: registered to indicate activity on CPUs [ 1.414003] usbcore: registered new interface driver usbhid [ 1.414004] usbhid: USB HID core driver [ 1.416885] NET: Registered protocol family 10 [ 1.417236] sit: IPv6 over IPv4 tunneling driver [ 1.417643] NET: Registered protocol family 17 [ 1.417649] can: controller area network core (rev 20120528 abi 9) [ 1.417681] NET: Registered protocol family 29 [ 1.417684] can: raw protocol (rev 20120528) [ 1.417687] can: broadcast manager protocol (rev 20120528 t) [ 1.417691] can: netlink gateway (rev 20130117) max_hops=1 [ 1.417888] Key type dns_resolver registered [ 1.421459] ThumbEE CPU extension supported. [ 1.421466] Registering SWP/SWPB emulation handler [ 1.428410] +3.3V_RUN: supplied by +3.3V_SYS [ 1.429148] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.429196] +1.8V_RUN_CAM: supplied by +3.3V_RUN [ 1.429372] +VDDIO_SDMMC3: supplied by +3.3V_RUN [ 1.429427] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN [ 1.429944] +VDD_LED: supplied by +VDD_MUX [ 1.430441] +5V_VDD_TS_SW: supplied by +5V_SYS [ 1.430694] +5V_USB_HS: supplied by +5V_SYS [ 1.431015] +5V_USB_SS: supplied by +5V_SYS [ 1.432702] +3.3V_PANEL: supplied by +3.3V_RUN [ 1.435525] +3.3V_LP0: supplied by +3.3V_SYS [ 1.436256] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 1.436525] +5V_HDMI_CON: supplied by +5V_SYS [ 1.437603] usb3-0 supply vbus not found, using dummy regulator [ 1.437680] usb3-1 supply vbus not found, using dummy regulator [ 1.441914] tegra-sor 54540000.sor: failed to probe output: -517 [ 1.442620] panel supply power not found, using dummy regulator [ 1.444058] sdhci-tegra 700b0000.sdhci: allocated mmc-pwrseq [ 1.444083] mmc1: Unknown controller version (3). You may experience problems. [ 1.444365] mmc1: Invalid maximum block size, assuming 512 bytes [ 1.444720] +1.8V_VDDIO: voltage operation not allowed [ 1.444724] mmc1: Switching to 3.3V signalling voltage failed [ 1.473129] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 1.474240] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.474251] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.474290] mmc2: Unknown controller version (3). You may experience problems. [ 1.474578] mmc2: Invalid maximum block size, assuming 512 bytes [ 1.479613] mmc0: new high speed MMC card at address 0001 [ 1.480235] mmcblk0: mmc0:0001 MMC16G 14.4 GiB [ 1.480579] mmcblk0boot0: mmc0:0001 MMC16G partition 1 2.00 MiB [ 1.480691] mmcblk0boot1: mmc0:0001 MMC16G partition 2 2.00 MiB [ 1.480790] mmcblk0rpmb: mmc0:0001 MMC16G partition 3 128 KiB [ 1.484439] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 [ 1.509291] mmc2: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA 64-bit [ 1.529211] mmc1: new high speed SDIO card at address 0001 [ 1.601240] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.601242] [drm] No driver support for vblank timestamp query. [ 1.655488] mmc2: new high speed SDHC card at address 0007 [ 1.656002] mmcblk2: mmc2:0007 SD08G 7.42 GiB [ 1.663704] GPT:Primary header alternate_lba != Alt. header my_lba [ 1.663708] GPT:3014591 != 15564799 [ 1.663710] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 1.663711] GPT:3014591 != 15564799 [ 1.663712] GPT: Use GNU Parted to correct GPT errors. [ 1.663740] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 [ 1.830551] Console: switching to colour frame buffer device 170x48 [ 1.840609] drm drm: fb0: frame buffer device [ 1.858109] [drm] Initialized tegra 0.0.0 20120330 on minor 0 [ 1.865080] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 1.872352] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:21 UTC (946684821) [ 1.884982] +1.8V_RUN_CAM: disabling [ 1.888788] +3.3V_RUN_CAM: disabling [ 1.892586] +1.2V_RUN_CAM_FRONT: disabling [ 1.896833] +1.05V_RUN_CAM_REAR: disabling [ 1.901088] +2.8V_RUN_TOUCH: disabling [ 1.904998] +2.8V_RUN_CAM_AF: disabling [ 1.908980] +1.8V_RUN_VPP_FUSE: disabling [ 1.913088] +5V_VDD_TS_SW: disabling [ 1.916659] +5V_USB_HS: disabling [ 1.919984] +5V_USB_SS: disabling [ 1.946261] input: Elan Touchpad as /devices/soc0/7000c400.i2c/i2c-1/1-0015/input/input1 [ 1.955487] EXT4-fs (mmcblk0p3): couldn't mount as ext3 due to feature incompatibilities [ 1.964126] EXT4-fs (mmcblk0p3): couldn't mount as ext2 due to feature incompatibilities [ 2.221494] EXT4-fs (mmcblk0p3): recovery complete [ 2.226941] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 2.235055] VFS: Mounted root (ext4 filesystem) on device 179:3. [ 2.241614] devtmpfs: mounted [ 2.245265] Freeing unused kernel memory: 2048K (c1100000 - c1300000) bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/# mount -t sysfs none /sys root@(none):/# root@(none):/# mount -t debugfs none /sys/kernel/debug root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:26 1970 [ 4.778187] PM: Syncing filesystems ... done. [ 4.787744] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 4.795923] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 4.805565] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 4.814198] Suspending console(s) (use no_console_suspend to debug) [ 4.874492] PM: suspend of devices complete after 53.474 msecs [ 4.875853] PM: late suspend of devices complete after 1.352 msecs [ 4.876609] PM: noirq suspend of devices complete after 0.751 msecs [ 4.876610] Disabling non-boot CPUs ... [ 4.877016] CPU1: shutdown [ 4.904085] CPU2: shutdown [ 4.928959] CPU3: shutdown [ 4.943464] Entering suspend state LP1 [ 4.943478] Enabling non-boot CPUs ... [ 4.968703] CPU1 is up [ 4.993725] CPU2 is up [ 5.018823] CPU3 is up [ 5.019279] PM: noirq resume of devices complete after 0.450 msecs [ 5.020391] PM: early resume of devices complete after 0.800 msecs [ 5.165586] +1.8V_VDDIO: voltage operation not allowed [ 5.165589] mmc1: Switching to 3.3V signalling voltage failed [ 5.228669] PM: resume of devices complete after 208.267 msecs [ 5.303379] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:30 1970 [ 5.807978] PM: Syncing filesystems ... done. [ 5.817459] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 5.825659] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 5.835307] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 5.843941] Suspending console(s) (use no_console_suspend to debug) [ 5.904519] PM: suspend of devices complete after 53.761 msecs [ 5.905463] PM: late suspend of devices complete after 0.940 msecs [ 5.906118] PM: noirq suspend of devices complete after 0.652 msecs [ 5.906120] Disabling non-boot CPUs ... [ 5.906506] CPU1: shutdown [ 5.919013] CPU2: shutdown [ 5.943728] IRQ17 no longer affine to CPU3 [ 5.943925] CPU3: shutdown [ 5.958446] Entering suspend state LP1 [ 5.958460] Enabling non-boot CPUs ... [ 5.983691] CPU1 is up [ 6.008696] CPU2 is up [ 6.033806] CPU3 is up [ 6.034297] PM: noirq resume of devices complete after 0.486 msecs [ 6.035450] PM: early resume of devices complete after 0.846 msecs [ 6.180032] +1.8V_VDDIO: voltage operation not allowed [ 6.180035] mmc1: Switching to 3.3V signalling voltage failed [ 6.240310] PM: resume of devices complete after 204.849 msecs [ 6.318931] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:34 1970 [ 6.822861] PM: Syncing filesystems ... done. [ 6.832486] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 6.840688] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 6.850332] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 6.858967] Suspending console(s) (use no_console_suspend to debug) [ 6.924519] PM: suspend of devices complete after 58.730 msecs [ 6.925806] PM: late suspend of devices complete after 1.277 msecs [ 6.926567] PM: noirq suspend of devices complete after 0.756 msecs [ 6.926568] Disabling non-boot CPUs ... [ 6.926926] CPU1: shutdown [ 6.939019] CPU2: shutdown [ 6.953877] CPU3: shutdown [ 6.968424] Entering suspend state LP1 [ 6.968438] Enabling non-boot CPUs ... [ 6.993668] CPU1 is up [ 7.018683] CPU2 is up [ 7.043785] CPU3 is up [ 7.044255] PM: noirq resume of devices complete after 0.466 msecs [ 7.045628] PM: early resume of devices complete after 1.046 msecs [ 7.190827] +1.8V_VDDIO: voltage operation not allowed [ 7.190831] mmc1: Switching to 3.3V signalling voltage failed [ 7.252670] PM: resume of devices complete after 207.031 msecs [ 7.327419] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:38 1970 [ 7.832772] PM: Syncing filesystems ... done. [ 7.842399] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 7.850599] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 7.860221] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 7.868915] Suspending console(s) (use no_console_suspend to debug) [ 7.934407] PM: suspend of devices complete after 58.673 msecs [ 7.935664] PM: late suspend of devices complete after 1.248 msecs [ 7.936424] PM: noirq suspend of devices complete after 0.755 msecs [ 7.936425] Disabling non-boot CPUs ... [ 7.936786] CPU1: shutdown [ 7.949002] CPU2: shutdown [ 7.973855] CPU3: shutdown [ 7.988392] Entering suspend state LP1 [ 7.988406] Enabling non-boot CPUs ... [ 8.013638] CPU1 is up [ 8.038652] CPU2 is up [ 8.063754] CPU3 is up [ 8.064225] PM: noirq resume of devices complete after 0.466 msecs [ 8.065629] PM: early resume of devices complete after 1.110 msecs [ 8.209937] +1.8V_VDDIO: voltage operation not allowed [ 8.209940] mmc1: Switching to 3.3V signalling voltage failed [ 8.272074] PM: resume of devices complete after 206.433 msecs [ 8.346672] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:42 1970 [ 8.852864] PM: Syncing filesystems ... done. [ 8.862488] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 8.870683] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 8.880327] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 8.888961] Suspending console(s) (use no_console_suspend to debug) [ 8.949406] PM: suspend of devices complete after 53.625 msecs [ 8.950682] PM: late suspend of devices complete after 1.266 msecs [ 8.951430] PM: noirq suspend of devices complete after 0.744 msecs [ 8.951431] Disabling non-boot CPUs ... [ 8.951787] CPU1: shutdown [ 8.973967] CPU2: shutdown [ 8.998652] IRQ17 no longer affine to CPU3 [ 8.998835] CPU3: shutdown [ 9.013379] Entering suspend state LP1 [ 9.013393] Enabling non-boot CPUs ... [ 9.038624] CPU1 is up [ 9.063640] CPU2 is up [ 9.088741] CPU3 is up [ 9.089212] PM: noirq resume of devices complete after 0.466 msecs [ 9.090387] PM: early resume of devices complete after 0.875 msecs [ 9.234921] +1.8V_VDDIO: voltage operation not allowed [ 9.234926] mmc1: Switching to 3.3V signalling voltage failed [ 9.297640] PM: resume of devices complete after 207.242 msecs [ 9.376316] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:46 1970 [ 9.876962] PM: Syncing filesystems ... done. [ 9.886483] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 9.894683] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 9.904296] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 9.912974] Suspending console(s) (use no_console_suspend to debug) [ 9.974375] PM: suspend of devices complete after 54.583 msecs [ 9.975626] PM: late suspend of devices complete after 1.243 msecs [ 9.976383] PM: noirq suspend of devices complete after 0.752 msecs [ 9.976385] Disabling non-boot CPUs ... [ 9.976747] CPU1: shutdown [ 9.998762] IRQ17 no longer affine to CPU2 [ 9.998949] CPU2: shutdown [ 10.023812] CPU3: shutdown [ 10.038351] Entering suspend state LP1 [ 10.038365] Enabling non-boot CPUs ... [ 10.063595] CPU1 is up [ 10.088608] CPU2 is up [ 10.113712] CPU3 is up [ 10.114179] PM: noirq resume of devices complete after 0.461 msecs [ 10.115331] PM: early resume of devices complete after 0.850 msecs [ 10.259659] +1.8V_VDDIO: voltage operation not allowed [ 10.259664] mmc1: Switching to 3.3V signalling voltage failed [ 10.322539] PM: resume of devices complete after 207.195 msecs [ 10.401248] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:50 1970 [ 10.907697] PM: Syncing filesystems ... done. [ 10.917146] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 10.925333] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 10.934988] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 10.943623] Suspending console(s) (use no_console_suspend to debug) [ 10.999469] PM: suspend of devices complete after 49.019 msecs [ 11.000704] PM: late suspend of devices complete after 1.227 msecs [ 11.001467] PM: noirq suspend of devices complete after 0.758 msecs [ 11.001469] Disabling non-boot CPUs ... [ 11.001669] IRQ17 no longer affine to CPU1 [ 11.001855] CPU1: shutdown [ 11.013909] CPU2: shutdown [ 11.028798] CPU3: shutdown [ 11.043329] Entering suspend state LP1 [ 11.043343] Enabling non-boot CPUs ... [ 11.068575] CPU1 is up [ 11.093590] CPU2 is up [ 11.118695] CPU3 is up [ 11.119162] PM: noirq resume of devices complete after 0.462 msecs [ 11.120420] PM: early resume of devices complete after 0.957 msecs [ 11.265483] +1.8V_VDDIO: voltage operation not allowed [ 11.265487] mmc1: Switching to 3.3V signalling voltage failed [ 11.327880] PM: resume of devices complete after 207.448 msecs [ 11.406634] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:54 1970 [ 11.912672] PM: Syncing filesystems ... done. [ 11.922263] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 11.930450] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 11.940104] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 11.948734] Suspending console(s) (use no_console_suspend to debug) [ 12.004463] PM: suspend of devices complete after 48.903 msecs [ 12.005734] PM: late suspend of devices complete after 1.262 msecs [ 12.006495] PM: noirq suspend of devices complete after 0.756 msecs [ 12.006497] Disabling non-boot CPUs ... [ 12.006679] IRQ17 no longer affine to CPU1 [ 12.006859] CPU1: shutdown [ 12.018906] CPU2: shutdown [ 12.033767] CPU3: shutdown [ 12.048310] Entering suspend state LP1 [ 12.048325] Enabling non-boot CPUs ... [ 12.073555] CPU1 is up [ 12.098564] CPU2 is up [ 12.123674] CPU3 is up [ 12.124142] PM: noirq resume of devices complete after 0.463 msecs [ 12.125312] PM: early resume of devices complete after 0.875 msecs [ 12.269591] +1.8V_VDDIO: voltage operation not allowed [ 12.269595] mmc1: Switching to 3.3V signalling voltage failed [ 12.332436] PM: resume of devices complete after 207.113 msecs [ 12.411133] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:58 1970 [ 12.917655] PM: Syncing filesystems ... done. [ 12.927247] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 12.935434] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 12.945089] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 12.953727] Suspending console(s) (use no_console_suspend to debug) [ 13.009312] PM: suspend of devices complete after 48.760 msecs [ 13.010591] PM: late suspend of devices complete after 1.269 msecs [ 13.011338] PM: noirq suspend of devices complete after 0.743 msecs [ 13.011340] Disabling non-boot CPUs ... [ 13.011698] CPU1: shutdown [ 13.033876] CPU2: shutdown [ 13.058557] IRQ17 no longer affine to CPU3 [ 13.058744] CPU3: shutdown [ 13.073288] Entering suspend state LP1 [ 13.073302] Enabling non-boot CPUs ... [ 13.098532] CPU1 is up [ 13.123545] CPU2 is up [ 13.148646] CPU3 is up [ 13.149113] PM: noirq resume of devices complete after 0.462 msecs [ 13.150265] PM: early resume of devices complete after 0.843 msecs [ 13.295305] +1.8V_VDDIO: voltage operation not allowed [ 13.295309] mmc1: Switching to 3.3V signalling voltage failed [ 13.357324] PM: resume of devices complete after 207.049 msecs [ 13.436018] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:01:02 1970 [ 13.942631] PM: Syncing filesystems ... done. [ 13.952227] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 13.960413] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 13.970067] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 13.978699] Suspending console(s) (use no_console_suspend to debug) [ 14.034251] PM: suspend of devices complete after 48.724 msecs [ 14.035354] PM: late suspend of devices complete after 1.094 msecs [ 14.036105] PM: noirq suspend of devices complete after 0.746 msecs [ 14.036106] Disabling non-boot CPUs ... [ 14.036472] CPU1: shutdown [ 14.058860] CPU2: shutdown [ 14.083539] IRQ17 no longer affine to CPU3 [ 14.083736] CPU3: shutdown [ 14.098260] Entering suspend state LP1 [ 14.098274] Enabling non-boot CPUs ... [ 14.123502] CPU1 is up [ 14.148518] CPU2 is up [ 14.173626] CPU3 is up [ 14.174097] PM: noirq resume of devices complete after 0.466 msecs [ 14.175266] PM: early resume of devices complete after 0.879 msecs [ 14.319821] +1.8V_VDDIO: voltage operation not allowed [ 14.319825] mmc1: Switching to 3.3V signalling voltage failed [ 14.382058] PM: resume of devices complete after 206.780 msecs [ 14.460734] Restarting tasks ... done. root@(none):/# root@(none):/# NVTB SYSTEM SUSPEND TEST COMPLETE