U-Boot 2015.04-00466-gedec83e90172 (Mar 14 2016 - 10:42:01) TEGRA124 Model: Acer Chromebook 13 CB5-311 DRAM: 4 GiB : Tegra SD/MMC: 0, Tegra SD/MMC: 1, Tegra SD/MMC: 2 MMC init failed Using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Nyan-big) # Tegra124 (Nyan-big) # usb start starting USB... USB0: USB EHCI 1.10 scanning bus 0 for devices... 2 USB Device(s) found USB1: USB EHCI 1.10 scanning bus 1 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... Warning: asx0 using MAC address from net device 1 Ethernet Device(s) found Tegra124 (Nyan-big) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=4d36e82a-b3c0-4b4b-bfcd-afe5217ac023 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Nyan-big) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Nyan-big) # tftpboot 0x82000000 zImage.multi_v7_defconfig Using asx0 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################### 2.8 MiB/s done Bytes transferred = 7239984 (6e7930 hex) Tegra124 (Nyan-big) # tftpboot 0x83000000 tegra124-nyan-big.dtb Using asx0 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-nyan-big.dtb'. Load address: 0x83000000 Loading: *##### 2.7 MiB/s done Bytes transferred = 66901 (10555 hex) Tegra124 (Nyan-big) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x6e7930 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83013554 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.7.0-rc7-96809-g92d21ac (pwalmsley@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Sun Jul 10 21:05:17 PDT 2016 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: Acer Chromebook 13 CB5-311 [ 0.000000] Ignoring memory range 0x100000000 - 0x17ffff000 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524287 [ 0.000000] free_area_init_node: node 0, pgdat c141bb40, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327679 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 13 pages/cpu @eef89000 s23808 r8192 d21248 u53248 [ 0.000000] pcpu-alloc: s23808 r8192 d21248 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522751 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=4d36e82a-b3c0-4b4b-bfcd-afe5217ac023 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1996016K/2097148K available (9529K kernel code, 1142K rwdata, 4476K rodata, 2048K init, 343K bss, 35596K reserved, 65536K cma-reserved, 1245180K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc10ad570 (14998 kB) [ 0.000000] .init : 0xc1100000 - 0xc1300000 (2048 kB) [ 0.000000] .data : 0xc1300000 - 0xc141dba0 (1143 kB) [ 0.000000] .bss : 0xc141f000 - 0xc1474ce0 ( 344 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@0,50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000004] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000013] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000019] Switching to timer-based delay loop, resolution 1000ns [ 0.001786] Architected cp15 timer(s) running at 12.00MHz (virt). [ 0.001793] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.001799] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.001803] Switching to timer-based delay loop, resolution 83ns [ 0.002004] Console: colour dummy device 80x30 [ 0.002017] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=60000) [ 0.002022] pid_max: default: 32768 minimum: 301 [ 0.002060] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002065] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002312] CPU: Testing write buffer coherency: ok [ 0.002424] /cpus/cpu@0 missing clock-frequency property [ 0.002439] /cpus/cpu@1 missing clock-frequency property [ 0.002453] /cpus/cpu@2 missing clock-frequency property [ 0.002468] /cpus/cpu@3 missing clock-frequency property [ 0.002472] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002481] Setting up static identity map for 0x80300000 - 0x80300098 [ 0.003771] Tegra Revision: A01 SKU: 131 CPU Process: 1 SoC Process: 1 [ 0.004374] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.006966] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.011960] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.016682] Brought up 4 CPUs [ 0.016690] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.016693] CPU: All CPU(s) started in SVC mode. [ 0.017237] devtmpfs: initialized [ 0.023568] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023842] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.024364] pinctrl core: initialized pinctrl subsystem [ 0.025037] NET: Registered protocol family 16 [ 0.025713] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.036716] cpuidle: using governor menu [ 0.043141] No ATAGs? [ 0.043154] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.043158] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.045249] Serial: AMBA PL011 UART driver [ 0.046225] tegra-mc 70019000.memory-controller: no memory timings for RAM code 0 registered [ 0.063448] +5V_SYS: supplied by +VDD_MUX [ 0.063553] +3.3V_SYS: supplied by +VDD_MUX [ 0.063775] +VDD_LED: Failed to request enable GPIO122: -517 [ 0.063780] reg-fixed-voltage regulators:regulator@5: Failed to register regulator: -517 [ 0.063811] +5V_VDD_TS_SW: Failed to request enable GPIO81: -517 [ 0.063815] reg-fixed-voltage regulators:regulator@6: Failed to register regulator: -517 [ 0.063844] +5V_USB_HS: Failed to request enable GPIO108: -517 [ 0.063848] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.063878] +5V_USB_SS: Failed to request enable GPIO109: -517 [ 0.063882] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.063960] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.063965] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.063993] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.063997] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.065120] vgaarb: loaded [ 0.065407] SCSI subsystem initialized [ 0.065477] libata version 3.00 loaded. [ 0.065578] usbcore: registered new interface driver usbfs [ 0.065600] usbcore: registered new interface driver hub [ 0.065625] usbcore: registered new device driver usb [ 0.067017] pps_core: LinuxPPS API ver. 1 registered [ 0.067021] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.067030] PTP clock support registered [ 0.067100] EDAC MC: Ver: 3.0.0 [ 0.067533] tegra-emc 7001b000.emc: no memory timings for RAM code 0 found in DT [ 0.067541] tegra-emc: probe of 7001b000.emc failed with error -2 [ 0.068026] clocksource: Switched to clocksource arch_sys_counter [ 0.071671] NET: Registered protocol family 2 [ 0.071883] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.071917] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.071979] TCP: Hash tables configured (established 8192 bind 8192) [ 0.072006] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.072020] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.072080] NET: Registered protocol family 1 [ 0.072181] RPC: Registered named UNIX socket transport module. [ 0.072185] RPC: Registered udp transport module. [ 0.072187] RPC: Registered tcp transport module. [ 0.072190] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.072194] PCI: CLS 0 bytes, default 64 [ 0.072632] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.073187] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.073474] workingset: timestamp_bits=28 max_order=19 bucket_order=0 [ 0.077271] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.077573] NFS: Registering the id_resolver key type [ 0.077586] Key type id_resolver registered [ 0.077589] Key type id_legacy registered [ 0.077606] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.078098] bounce: pool size: 64 pages [ 0.078172] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.078177] io scheduler noop registered [ 0.078180] io scheduler deadline registered [ 0.078191] io scheduler cfq registered (default) [ 0.080097] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.089008] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.089697] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.110470] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.111618] console [ttyS0] disabled [ 0.111634] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 331, base_baud = 25500000) is a Tegra [ 0.964635] console [ttyS0] enabled [ 0.968430] SuperH (H)SCI(F) driver initialized [ 0.973314] msm_serial: driver initialized [ 0.977464] STMicroelectronics ASC driver initialized [ 0.983945] [drm] Initialized drm 1.1.0 20060810 [ 0.989975] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 0.996528] tegra-dpaux 545c0000.dpaux: failed to get VDD supply: -517 [ 1.003744] panel supply power not found, using dummy regulator [ 1.013479] brd: module loaded [ 1.018614] loop: module loaded [ 1.022652] as3722 4-0040: AS3722 with revision 0x1 found [ 1.032365] as3722-sd2: supplied by +5V_SYS [ 1.036811] as3722-sd3: supplied by +5V_SYS [ 1.041148] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.047337] as3722-sd4: supplied by +5V_SYS [ 1.051674] +1.05V_RUN: Bringing 0uV into 1050000-1050000uV [ 1.057422] as3722-sd5: supplied by +5V_SYS [ 1.063014] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.068751] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.074780] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.080401] as3722-ldo3: supplied by +3.3V_SYS [ 1.084850] +1.00V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.092428] as3722-ldo4: supplied by +3.3V_SYS [ 1.097024] +3.3V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.103056] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.107817] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.114512] +VDDIO_SDMMC3: Bringing 0uV into 1800000-1800000uV [ 1.120546] as3722-ldo7: supplied by +1.8V_VDDIO [ 1.125315] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 1.131881] as3722-ldo9: supplied by +5V_SYS [ 1.136444] +2.8V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 1.142651] as3722-ldo10: supplied by +5V_SYS [ 1.147158] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 1.153606] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 1.171845] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.178131] libphy: Fixed MDIO Bus: probed [ 1.182458] CAN device driver interface [ 1.187006] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.193954] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.200674] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.208082] usbcore: registered new interface driver pegasus [ 1.213752] usbcore: registered new interface driver asix [ 1.219156] usbcore: registered new interface driver ax88179_178a [ 1.225253] usbcore: registered new interface driver cdc_ether [ 1.231096] usbcore: registered new interface driver smsc75xx [ 1.236852] usbcore: registered new interface driver smsc95xx [ 1.242601] usbcore: registered new interface driver net1080 [ 1.248267] usbcore: registered new interface driver cdc_subset [ 1.254191] usbcore: registered new interface driver zaurus [ 1.259781] usbcore: registered new interface driver cdc_ncm [ 1.266147] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.272663] ehci-pci: EHCI PCI platform driver [ 1.277112] ehci-platform: EHCI generic platform driver [ 1.282404] ehci-omap: OMAP-EHCI Host Controller driver [ 1.287669] ehci-orion: EHCI orion driver [ 1.291722] SPEAr-ehci: EHCI SPEAr driver [ 1.295778] ehci-st: EHCI STMicroelectronics driver [ 1.300698] ehci-exynos: EHCI EXYNOS driver [ 1.304932] ehci-atmel: EHCI Atmel driver [ 1.308985] tegra-ehci: Tegra EHCI driver [ 1.313053] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.319226] ohci-pci: OHCI PCI platform driver [ 1.323678] ohci-platform: OHCI generic platform driver [ 1.328952] ohci-omap3: OHCI OMAP3 driver [ 1.332998] SPEAr-ohci: OHCI SPEAr driver [ 1.337051] ohci-st: OHCI STMicroelectronics driver [ 1.341971] ohci-atmel: OHCI Atmel driver [ 1.346242] usbcore: registered new interface driver usb-storage [ 1.352835] mousedev: PS/2 mouse device common for all mice [ 1.358810] 1-0015 supply vcc not found, using dummy regulator [ 1.360622] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.360625] as3722-rtc as3722-rtc: RTC interrupt 370 [ 1.362888] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.362912] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.363210] i2c /dev entries driver [ 1.366549] 0-004c supply vcc not found, using dummy regulator [ 1.381575] sdhci: Secure Digital Host Controller Interface driver [ 1.381576] sdhci: Copyright(c) Pierre Ossman [ 1.382307] Synopsys Designware Multimedia Card Interface Driver [ 1.382851] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.383242] sdhci-tegra 700b0000.sdhci: allocated mmc-pwrseq [ 1.383266] mmc0: Unknown controller version (3). You may experience problems. [ 1.383471] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.383480] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.383511] mmc0: Unknown controller version (3). You may experience problems. [ 1.383684] mmc0: Unknown controller version (3). You may experience problems. [ 1.383727] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.418034] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.418846] ledtrig-cpu: registered to indicate activity on CPUs [ 1.419011] usbcore: registered new interface driver usbhid [ 1.419012] usbhid: USB HID core driver [ 1.421875] NET: Registered protocol family 10 [ 1.422229] sit: IPv6 over IPv4 tunneling driver [ 1.422625] NET: Registered protocol family 17 [ 1.422631] can: controller area network core (rev 20120528 abi 9) [ 1.422665] NET: Registered protocol family 29 [ 1.422668] can: raw protocol (rev 20120528) [ 1.422670] can: broadcast manager protocol (rev 20120528 t) [ 1.422675] can: netlink gateway (rev 20130117) max_hops=1 [ 1.422873] Key type dns_resolver registered [ 1.427033] ThumbEE CPU extension supported. [ 1.427038] Registering SWP/SWPB emulation handler [ 1.433992] +3.3V_RUN: supplied by +3.3V_SYS [ 1.434780] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.434935] +1.8V_RUN_CAM: supplied by +3.3V_RUN [ 1.434980] +VDDIO_SDMMC3: supplied by +3.3V_RUN [ 1.435019] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN [ 1.435508] +VDD_LED: supplied by +VDD_MUX [ 1.435918] +5V_VDD_TS_SW: supplied by +5V_SYS [ 1.436249] +5V_USB_HS: supplied by +5V_SYS [ 1.436494] +5V_USB_SS: supplied by +5V_SYS [ 1.439713] +3.3V_PANEL: supplied by +3.3V_RUN [ 1.441456] +3.3V_LP0: supplied by +3.3V_SYS [ 1.442616] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 1.442921] +5V_HDMI_CON: supplied by +5V_SYS [ 1.444251] usb3-0 supply vbus not found, using dummy regulator [ 1.444330] usb3-1 supply vbus not found, using dummy regulator [ 1.447889] tegra-sor 54540000.sor: failed to probe output: -517 [ 1.448992] panel supply power not found, using dummy regulator [ 1.450089] sdhci-tegra 700b0000.sdhci: allocated mmc-pwrseq [ 1.450109] mmc1: Unknown controller version (3). You may experience problems. [ 1.450313] mmc1: Invalid maximum block size, assuming 512 bytes [ 1.450827] +1.8V_VDDIO: voltage operation not allowed [ 1.450830] mmc1: Switching to 3.3V signalling voltage failed [ 1.483130] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 1.484300] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.484310] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.484348] mmc2: Unknown controller version (3). You may experience problems. [ 1.484574] mmc0: new high speed MMC card at address 0001 [ 1.484642] mmc2: Invalid maximum block size, assuming 512 bytes [ 1.485356] mmcblk0: mmc0:0001 MMC16G 14.4 GiB [ 1.488125] mmcblk0boot0: mmc0:0001 MMC16G partition 1 2.00 MiB [ 1.488711] mmcblk0boot1: mmc0:0001 MMC16G partition 2 2.00 MiB [ 1.489063] mmcblk0rpmb: mmc0:0001 MMC16G partition 3 128 KiB [ 1.494954] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 [ 1.518980] mmc2: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA 64-bit [ 1.539052] mmc1: new high speed SDIO card at address 0001 [ 1.611217] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.611219] [drm] No driver support for vblank timestamp query. [ 1.660498] mmc2: new high speed SDHC card at address 0007 [ 1.661012] mmcblk2: mmc2:0007 SD08G 7.42 GiB [ 1.668741] GPT:Primary header alternate_lba != Alt. header my_lba [ 1.668746] GPT:3014591 != 15564799 [ 1.668747] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 1.668749] GPT:3014591 != 15564799 [ 1.668751] GPT: Use GNU Parted to correct GPT errors. [ 1.668776] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 [ 1.830845] Console: switching to colour frame buffer device 170x48 [ 1.840911] drm drm: fb0: frame buffer device [ 1.858117] [drm] Initialized tegra 0.0.0 20120330 on minor 0 [ 1.865089] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 1.872364] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:21 UTC (946684821) [ 1.884978] +1.8V_RUN_CAM: disabling [ 1.888783] +3.3V_RUN_CAM: disabling [ 1.892579] +1.2V_RUN_CAM_FRONT: disabling [ 1.896826] +1.05V_RUN_CAM_REAR: disabling [ 1.901083] +2.8V_RUN_TOUCH: disabling [ 1.904992] +2.8V_RUN_CAM_AF: disabling [ 1.908974] +1.8V_RUN_VPP_FUSE: disabling [ 1.913083] +5V_VDD_TS_SW: disabling [ 1.916657] +5V_USB_HS: disabling [ 1.919972] +5V_USB_SS: disabling [ 1.946224] input: Elan Touchpad as /devices/soc0/7000c400.i2c/i2c-1/1-0015/input/input1 [ 1.955446] EXT4-fs (mmcblk0p3): couldn't mount as ext3 due to feature incompatibilities [ 1.964068] EXT4-fs (mmcblk0p3): couldn't mount as ext2 due to feature incompatibilities [ 2.220444] EXT4-fs (mmcblk0p3): recovery complete [ 2.225248] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 2.233342] VFS: Mounted root (ext4 filesystem) on device 179:3. [ 2.240230] devtmpfs: mounted [ 2.243885] Freeing unused kernel memory: 2048K (c1100000 - c1300000) bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/# mount -t sysfs none /sys root@(none):/# root@(none):/# mount -t debugfs none /sys/kernel/debug root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:26 1970 [ 4.767653] PM: Syncing filesystems ... done. [ 4.777364] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 4.785551] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 4.795252] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 4.803947] Suspending console(s) (use no_console_suspend to debug) [ 4.859494] PM: suspend of devices complete after 48.736 msecs [ 4.860732] PM: late suspend of devices complete after 1.229 msecs [ 4.861488] PM: noirq suspend of devices complete after 0.751 msecs [ 4.861490] Disabling non-boot CPUs ... [ 4.861674] IRQ17 no longer affine to CPU1 [ 4.861841] CPU1: shutdown [ 4.874085] CPU2: shutdown [ 4.898963] CPU3: shutdown [ 4.913468] Entering suspend state LP1 [ 4.913482] Enabling non-boot CPUs ... [ 4.938703] CPU1 is up [ 4.963725] CPU2 is up [ 4.988824] CPU3 is up [ 4.989322] PM: noirq resume of devices complete after 0.494 msecs [ 4.990650] PM: early resume of devices complete after 1.030 msecs [ 5.134885] +1.8V_VDDIO: voltage operation not allowed [ 5.134888] mmc1: Switching to 3.3V signalling voltage failed [ 5.196554] PM: resume of devices complete after 205.893 msecs [ 5.275169] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:30 1970 [ 5.822776] PM: Syncing filesystems ... done. [ 5.832223] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 5.840432] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 5.850023] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 5.858726] Suspending console(s) (use no_console_suspend to debug) [ 5.909704] PM: suspend of devices complete after 44.171 msecs [ 5.910612] PM: late suspend of devices complete after 0.899 msecs [ 5.911334] PM: noirq suspend of devices complete after 0.717 msecs [ 5.911335] Disabling non-boot CPUs ... [ 5.911694] CPU1: shutdown [ 5.923853] IRQ17 no longer affine to CPU2 [ 5.924041] CPU2: shutdown [ 5.948903] CPU3: shutdown [ 5.963447] Entering suspend state LP1 [ 5.963460] Enabling non-boot CPUs ... [ 5.988679] CPU1 is up [ 6.013700] CPU2 is up [ 6.038798] CPU3 is up [ 6.039294] PM: noirq resume of devices complete after 0.492 msecs [ 6.040495] PM: early resume of devices complete after 0.888 msecs [ 6.185640] +1.8V_VDDIO: voltage operation not allowed [ 6.185643] mmc1: Switching to 3.3V signalling voltage failed [ 6.247244] PM: resume of devices complete after 206.739 msecs [ 6.325923] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:34 1970 [ 6.872034] PM: Syncing filesystems ... done. [ 6.881518] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 6.889683] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 6.899273] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 6.907962] Suspending console(s) (use no_console_suspend to debug) [ 6.959581] PM: suspend of devices complete after 44.801 msecs [ 6.960514] PM: late suspend of devices complete after 0.924 msecs [ 6.961242] PM: noirq suspend of devices complete after 0.724 msecs [ 6.961244] Disabling non-boot CPUs ... [ 6.961430] IRQ17 no longer affine to CPU1 [ 6.961604] CPU1: shutdown [ 6.974016] CPU2: shutdown [ 6.988881] CPU3: shutdown [ 7.003429] Entering suspend state LP1 [ 7.003442] Enabling non-boot CPUs ... [ 7.028661] CPU1 is up [ 7.053678] CPU2 is up [ 7.078778] CPU3 is up [ 7.079251] PM: noirq resume of devices complete after 0.469 msecs [ 7.080451] PM: early resume of devices complete after 0.894 msecs [ 7.225029] +1.8V_VDDIO: voltage operation not allowed [ 7.225032] mmc1: Switching to 3.3V signalling voltage failed [ 7.287214] PM: resume of devices complete after 206.753 msecs [ 7.365896] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:38 1970 [ 7.912795] PM: Syncing filesystems ... done. [ 7.922399] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 7.930609] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 7.940199] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 7.948906] Suspending console(s) (use no_console_suspend to debug) [ 7.999521] PM: suspend of devices complete after 43.806 msecs [ 8.000436] PM: late suspend of devices complete after 0.907 msecs [ 8.001158] PM: noirq suspend of devices complete after 0.718 msecs [ 8.001160] Disabling non-boot CPUs ... [ 8.001514] CPU1: shutdown [ 8.013990] CPU2: shutdown [ 8.028867] CPU3: shutdown [ 8.043400] Entering suspend state LP1 [ 8.043414] Enabling non-boot CPUs ... [ 8.068637] CPU1 is up [ 8.093655] CPU2 is up [ 8.118750] CPU3 is up [ 8.119219] PM: noirq resume of devices complete after 0.464 msecs [ 8.120462] PM: early resume of devices complete after 0.941 msecs [ 8.264779] +1.8V_VDDIO: voltage operation not allowed [ 8.264783] mmc1: Switching to 3.3V signalling voltage failed [ 8.327546] PM: resume of devices complete after 207.073 msecs [ 8.402164] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:42 1970 [ 8.952768] PM: Syncing filesystems ... done. [ 8.962362] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 8.970574] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 8.980165] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 8.988879] Suspending console(s) (use no_console_suspend to debug) [ 9.039516] PM: suspend of devices complete after 43.825 msecs [ 9.040650] PM: late suspend of devices complete after 1.125 msecs [ 9.041394] PM: noirq suspend of devices complete after 0.740 msecs [ 9.041395] Disabling non-boot CPUs ... [ 9.041750] CPU1: shutdown [ 9.053965] CPU2: shutdown [ 9.068838] CPU3: shutdown [ 9.083379] Entering suspend state LP1 [ 9.083393] Enabling non-boot CPUs ... [ 9.108610] CPU1 is up [ 9.133630] CPU2 is up [ 9.158727] CPU3 is up [ 9.159195] PM: noirq resume of devices complete after 0.463 msecs [ 9.160549] PM: early resume of devices complete after 1.048 msecs [ 9.305378] +1.8V_VDDIO: voltage operation not allowed [ 9.305382] mmc1: Switching to 3.3V signalling voltage failed [ 9.367365] PM: resume of devices complete after 206.806 msecs [ 9.441974] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:46 1970 [ 9.992402] PM: Syncing filesystems ... done. [ 10.001853] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 10.010063] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 10.019654] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 10.028354] Suspending console(s) (use no_console_suspend to debug) [ 10.074451] PM: suspend of devices complete after 39.288 msecs [ 10.075268] PM: late suspend of devices complete after 0.813 msecs [ 10.075930] PM: noirq suspend of devices complete after 0.659 msecs [ 10.075932] Disabling non-boot CPUs ... [ 10.076295] CPU1: shutdown [ 10.088958] CPU2: shutdown [ 10.103814] CPU3: shutdown [ 10.118352] Entering suspend state LP1 [ 10.118366] Enabling non-boot CPUs ... [ 10.143589] CPU1 is up [ 10.168609] CPU2 is up [ 10.193708] CPU3 is up [ 10.194176] PM: noirq resume of devices complete after 0.464 msecs [ 10.195447] PM: early resume of devices complete after 0.961 msecs [ 10.340038] +1.8V_VDDIO: voltage operation not allowed [ 10.340041] mmc1: Switching to 3.3V signalling voltage failed [ 10.403002] PM: resume of devices complete after 207.544 msecs [ 10.477550] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:50 1970 [ 11.027646] PM: Syncing filesystems ... done. [ 11.037089] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 11.045302] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 11.054892] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 11.063594] Suspending console(s) (use no_console_suspend to debug) [ 11.114417] PM: suspend of devices complete after 44.016 msecs [ 11.115365] PM: late suspend of devices complete after 0.939 msecs [ 11.116125] PM: noirq suspend of devices complete after 0.756 msecs [ 11.116127] Disabling non-boot CPUs ... [ 11.116498] CPU1: shutdown [ 11.143906] CPU2: shutdown [ 11.168619] IRQ17 no longer affine to CPU3 [ 11.168808] CPU3: shutdown [ 11.183329] Entering suspend state LP1 [ 11.183342] Enabling non-boot CPUs ... [ 11.208564] CPU1 is up [ 11.233582] CPU2 is up [ 11.258682] CPU3 is up [ 11.259145] PM: noirq resume of devices complete after 0.459 msecs [ 11.260278] PM: early resume of devices complete after 0.814 msecs [ 11.404718] +1.8V_VDDIO: voltage operation not allowed [ 11.404721] mmc1: Switching to 3.3V signalling voltage failed [ 11.467418] PM: resume of devices complete after 207.128 msecs [ 11.546115] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:54 1970 [ 12.092134] PM: Syncing filesystems ... done. [ 12.101584] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 12.109796] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 12.119387] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 12.128091] Suspending console(s) (use no_console_suspend to debug) [ 12.179394] PM: suspend of devices complete after 44.497 msecs [ 12.180332] PM: late suspend of devices complete after 0.929 msecs [ 12.181086] PM: noirq suspend of devices complete after 0.750 msecs [ 12.181088] Disabling non-boot CPUs ... [ 12.181443] CPU1: shutdown [ 12.203715] IRQ17 no longer affine to CPU2 [ 12.203905] CPU2: shutdown [ 12.228775] CPU3: shutdown [ 12.243312] Entering suspend state LP1 [ 12.243325] Enabling non-boot CPUs ... [ 12.268541] CPU1 is up [ 12.293559] CPU2 is up [ 12.318663] CPU3 is up [ 12.319127] PM: noirq resume of devices complete after 0.460 msecs [ 12.319984] PM: early resume of devices complete after 0.575 msecs [ 12.464747] +1.8V_VDDIO: voltage operation not allowed [ 12.464749] mmc1: Switching to 3.3V signalling voltage failed [ 12.527186] PM: resume of devices complete after 207.193 msecs [ 12.605891] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:58 1970 [ 13.152678] PM: Syncing filesystems ... done. [ 13.162277] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 13.170487] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 13.180079] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 13.188792] Suspending console(s) (use no_console_suspend to debug) [ 13.239293] PM: suspend of devices complete after 43.687 msecs [ 13.240266] PM: late suspend of devices complete after 0.965 msecs [ 13.241026] PM: noirq suspend of devices complete after 0.756 msecs [ 13.241028] Disabling non-boot CPUs ... [ 13.241384] CPU1: shutdown [ 13.263692] IRQ17 no longer affine to CPU2 [ 13.263882] CPU2: shutdown [ 13.288743] CPU3: shutdown [ 13.303288] Entering suspend state LP1 [ 13.303301] Enabling non-boot CPUs ... [ 13.328517] CPU1 is up [ 13.353541] CPU2 is up [ 13.378635] CPU3 is up [ 13.379108] PM: noirq resume of devices complete after 0.468 msecs [ 13.380223] PM: early resume of devices complete after 0.807 msecs [ 13.525321] +1.8V_VDDIO: voltage operation not allowed [ 13.525324] mmc1: Switching to 3.3V signalling voltage failed [ 13.587369] PM: resume of devices complete after 207.135 msecs [ 13.666052] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:01:02 1970 [ 14.217787] PM: Syncing filesystems ... done. [ 14.227413] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 14.235607] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) [ 14.245254] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 14.253896] Suspending console(s) (use no_console_suspend to debug) [ 14.314264] PM: suspend of devices complete after 53.546 msecs [ 14.315196] PM: late suspend of devices complete after 0.924 msecs [ 14.315924] PM: noirq suspend of devices complete after 0.723 msecs [ 14.315926] Disabling non-boot CPUs ... [ 14.316282] CPU1: shutdown [ 14.328668] IRQ17 no longer affine to CPU2 [ 14.328858] CPU2: shutdown [ 14.353727] CPU3: shutdown [ 14.368267] Entering suspend state LP1 [ 14.368281] Enabling non-boot CPUs ... [ 14.393499] CPU1 is up [ 14.418517] CPU2 is up [ 14.443616] CPU3 is up [ 14.444087] PM: noirq resume of devices complete after 0.466 msecs [ 14.445380] PM: early resume of devices complete after 0.985 msecs [ 14.590305] +1.8V_VDDIO: voltage operation not allowed [ 14.590309] mmc1: Switching to 3.3V signalling voltage failed [ 14.652084] PM: resume of devices complete after 206.694 msecs [ 14.730778] Restarting tasks ... done. root@(none):/# root@(none):/# NVTB SYSTEM SUSPEND TEST COMPLETE