[0000.738] [TegraBoot] (version 23.00.2015.14-mobile-1ef66670) [0000.743] Processing in cold boot mode Bootloader 2 [0000.748] A01Q Bootrom Patch rev = 3 [0000.751] Power-up reason: pmu watchdog [0000.755] No Battery Present [0000.758] Platform has Ddr4 type ram [0000.761] max77620 disabling SD1 Remote Sense [0000.765] Setting Ddr voltage to 1125mv [0000.770] Serial Number of Pmic Max77663: 0x40daf [0000.777] Entering ramdump check [0000.780] Get RamDumpCarveOut = 0x0 [0000.784] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.789] Last reboot was clean, booting normally! [0000.793] Sdram initialization is successful [0000.797] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.803] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.829] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.855] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.860] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.865] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.870] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.875] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.891] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.896] Platform-DebugCarveout: 0 [0000.899] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.949] Using GPT Primary to query partitions [0000.954] Loading Tboot-CPU binary [0001.003] Verifying bootloader in OdmNonSecureSBK mode [0001.013] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.022] Bootloader downloaded successfully. [0001.026] Downloaded Tboot-CPU binary to 0xa0000258 [0001.032] MAX77620_GPIO1 Configured. [0001.036] MAX77620_GPIO5 Configured. [0001.039] CPU power rail is up [0001.042] CPU clock enabled [0001.046] Performing RAM repair [0001.049] Updating A64 Warmreset Address to 0xa00002e9 [0001.068] Bootloader DTB Load Address: 0x83000000 [0001.085] Kernel DTB Load Address: 0x83080000 [0001.090] Loading cboot binary [0001.184] Verifying bootloader in OdmNonSecureSBK mode [0001.272] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0001.281] Bootloader downloaded successfully. [0001.285] GPT: Partition NOT found ! [0001.288] Find Partition via GPT Failed [0001.292] function NvTbootGetBinaryOffsets: 0x845208 error [0001.297] Error in NvTbootLoadBinary: 0x845208 ! [0001.302] GPT: Partition NOT found ! [0001.305] No FB partition [0001.308] Next binary entry address: 0x80110000 [0001.312] BoardId: 2595 [0001.317] dram memory type is 3 [0001.323] WB0 init successful [0001.349] Bpmp FW successfully loaded [0001.353] Set NvDecSticky Bits [0001.356] GSC1 address : ff700000 [0001.360] GSC2 address : ff600000 [0001.364] GSC3 address : ff500000 [0001.367] GSC4 address : ff400000 [0001.371] GSC5 address : ff300000 [0001.374] GSC MC Settings done [0001.379] TOS old plaintext Image length 61440 [0001.386] *** Secure OS image signature not verified *** [0001.391] Loading and Validation of Secure OS Successful [0001.396] NvTbootPackSdramParams: start. [0001.401] NvTbootPackSdramParams: done. [0001.405] Tegraboot started after 730611 us [0001.409] Basic modules init took 348824 us [0001.413] Sec Bootdevice Read Time = 202 ms, Read Size = 8459 KB [0001.418] Next stage binary read took 14370 us [0001.423] Carveout took 252731 us [0001.426] CPU initialization took 92299 us [0001.430] Total time taken by TegraBoot 708224 us [0001.434] Starting CPU & Halting co-processor 64b[0001.570] LPDDR4 Training: Number of tables = 10 [0001.574] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.580] EMC Training Successful [0001.583] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.589] EMC Training Successful [0001.592] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.604] EMC Training Successful [0001.607] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.629] EMC Training Successful [0001.632] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.654] EMC Training Successful [0001.657] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.676] EMC Training Successful [0001.680] Switching to 800000 KHz Success [0001.713] LPDDR4 Training: Number of tables = 10 U-Boot 2015.07-rc2-g2ac3917 (Nov 09 2015 - 13:12:08 -0800) TEGRA210 Model: NVIDIA P2371-0000 DRAM: 3 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0x1d5a000 |/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/CTRL+C - Operation aborted Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # env set fdt_copy_node_names /cpus:/psci Tegra210 (P2371-0000) # setenv rootpart 1 Tegra210 (P2371-0000) # setenv devtype mmc Tegra210 (P2371-0000) # setenv devnum 0 Tegra210 (P2371-0000) # part uuid ${devtype} ${devnum}:${rootpart} uuid Tegra210 (P2371-0000) # setenv bootargs ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=/dev/mmcblk0p1 rootwait debug earlyprintk init=/bin/bash Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${kernel_addr_r} /boot/Image.defconfig 11007488 bytes read in 704 ms (14.9 MiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${fdt_addr_r} /boot/tegra210-p2371-0000.dtb 37136 bytes read in 460 ms (78.1 KiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${ramdisk_addr_r} /boot/tegra-ramdisk.img 1627787 bytes read in 494 ms (3.1 MiB/s) Tegra210 (P2371-0000) # ramdisk_size=${filesize} Tegra210 (P2371-0000) # booti ${kernel_addr_r} - ${fdt_addr_r} ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200c10f Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.5.0-rc4+ (pwalmsley@tamien) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sun Feb 14 13:36:03 PST 2016 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] earlycon: Early serial console at MMIO32 0x70006000 (options '') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000fe000000 [ 0.000000] On node 0 totalpages: 782848 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 520704 pages, LIFO batch:31 [ 0.000000] Normal zone: 4096 pages used for memmap [ 0.000000] Normal zone: 262144 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 20 pages/cpu @ffffffc0bff61000 s41984 r8192 d31744 u81920 [ 0.000000] pcpu-alloc: s41984 r8192 d31744 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] CPU features: enabling workaround for ARM erratum 834220 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 770560 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=/dev/mmcblk0p1 rootwait debug earlyprintk init=/bin/bash [ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes [ 0.000000] log_buf_len min size: 16384 bytes [ 0.000000] log_buf_len: 32768 bytes [ 0.000000] early log buf free: 14320(87%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB [mem 0xfa000000-0xfe000000] (64MB) mapped at [ffffffc07a000000-ffffffc07dffffff] [ 0.000000] Memory: 2981992K/3131392K available (6512K kernel code, 597K rwdata, 2904K rodata, 724K init, 243K bss, 133016K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc2000000 - 0xffffffbdc5000000 ( 48 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0c0000000 ( 3072 MB) [ 0.000000] .init : 0xffffffc0009b5000 - 0xffffffc000a6a000 ( 724 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0009b42a4 ( 9425 KB) [ 0.000000] .data : 0xffffffc000a6a000 - 0xffffffc000aff600 ( 598 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] /interrupt-controller@0,60004000: 192 interrupts forwarded to /interrupt-controller@0,50041000 [ 0.000000] PLL_MB already enabled. Postponing set full defaults [ 0.000000] PLL_U already enabled. Postponing set full defaults [ 0.000000] PLL_P already enabled. Postponing set full defaults [ 0.000000] PLL_X already enabled. Postponing set full defaults [ 0.000000] boot misc1 0x0: expected 0x20 [ 0.000000] (comparison mask = 0xffffff) [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.008392] Console: colour dummy device 80x25 [ 0.013004] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.023618] pid_max: default: 32768 minimum: 301 [ 0.028451] Security Framework initialized [ 0.032724] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.039663] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.047885] ASID allocator initialised with 65536 entries [ 0.074147] Speedo Revision 4 [ 0.077226] Tegra Revision: A01 SKU: 1 CPU Process: -22 SoC Process: -22 [ 0.084638] EFI services will not be available. [ 0.105426] Detected PIPT I-cache on CPU1 [ 0.105465] CPU1: Booted secondary processor [411fd071] [ 0.117447] Detected PIPT I-cache on CPU2 [ 0.117476] CPU2: Booted secondary processor [411fd071] [ 0.129474] Detected PIPT I-cache on CPU3 [ 0.129503] CPU3: Booted secondary processor [411fd071] [ 0.129562] Brought up 4 CPUs [ 0.161233] SMP: Total of 4 processors activated. [ 0.166100] CPU: All CPU(s) started at EL2 [ 0.170352] alternatives: patching kernel code [ 0.176741] devtmpfs: initialized [ 0.188000] DMI not present or invalid. [ 0.192205] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.202761] pinctrl core: initialized pinctrl subsystem [ 0.209400] NET: Registered protocol family 16 [ 0.226056] cpuidle: using governor menu [ 0.230314] vdso: 2 pages (1 code @ ffffffc000a71000, 1 data @ ffffffc000a70000) [ 0.238011] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.245867] DMA: preallocated 256 KiB pool for atomic allocations [ 0.252409] Serial: AMBA PL011 UART driver [ 0.289043] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.297308] vgaarb: loaded [ 0.300330] SCSI subsystem initialized [ 0.304354] libata version 3.00 loaded. [ 0.308586] usbcore: registered new interface driver usbfs [ 0.314336] usbcore: registered new interface driver hub [ 0.319924] usbcore: registered new device driver usb [ 0.325281] pps_core: LinuxPPS API ver. 1 registered [ 0.330427] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.339915] PTP clock support registered [ 0.344134] dmi: Firmware registration failed. [ 0.348912] Advanced Linux Sound Architecture Driver Initialized. [ 0.355865] clocksource: Switched to clocksource arch_sys_counter [ 0.362310] VFS: Disk quotas dquot_6.6.0 [ 0.366423] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.381209] NET: Registered protocol family 2 [ 0.386225] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.393928] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.401088] TCP: Hash tables configured (established 32768 bind 32768) [ 0.408043] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.414323] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.421192] NET: Registered protocol family 1 [ 0.425929] RPC: Registered named UNIX socket transport module. [ 0.432082] RPC: Registered udp transport module. [ 0.436976] RPC: Registered tcp transport module. [ 0.441855] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.448545] PCI: CLS 0 bytes, default 128 [ 0.453763] kvm [1]: interrupt-controller@50044000 IRQ9 [ 0.459603] kvm [1]: timer IRQ3 [ 0.462882] kvm [1]: 8-bit VMID [ 0.466139] kvm [1]: Hyp mode initialized successfully [ 0.474042] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.480658] audit: initializing netlink subsys (disabled) [ 0.486289] audit: type=2000 audit(0.415:1): initialized [ 0.502188] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.509106] NFS: Registering the id_resolver key type [ 0.514577] Key type id_resolver registered [ 0.518943] Key type id_legacy registered [ 0.523308] fuse init (API version 7.24) [ 0.527913] 9p: Installing v9fs 9p2000 file system support [ 0.535989] io scheduler noop registered [ 0.540227] io scheduler cfq registered (default) [ 0.554441] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.562737] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.572363] xenfs: not registering filesystem on non-xen platform [ 0.581948] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.590012] console [ttyS0] disabled [ 0.593763] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 312, base_baud = 25500000) is a Tegra [ 0.603083] console [ttyS0] enabled [ 0.603083] console [ttyS0] enabled [ 0.610176] bootconsole [uart0] disabled [ 0.610176] bootconsole [uart0] disabled [ 0.618526] SuperH (H)SCI(F) driver initialized [ 0.623240] msm_serial: driver initialized [ 0.627716] Unable to detect cache hierarchy from DT for CPU 0 [ 0.638132] loop: module loaded [ 0.642462] tun: Universal TUN/TAP device driver, 1.6 [ 0.647529] tun: (C) 1999-2004 Max Krasnyansky [ 0.654020] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.659879] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.665855] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 0.672812] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.678445] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k [ 0.686267] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.692243] sky2: driver version 1.30 [ 0.696298] VFIO - User Level meta-driver version: 0.3 [ 0.702019] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.708570] ehci-pci: EHCI PCI platform driver [ 0.713084] ehci-platform: EHCI generic platform driver [ 0.718395] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.724586] ohci-pci: OHCI PCI platform driver [ 0.729078] ohci-platform: OHCI generic platform driver [ 0.734430] usbcore: registered new interface driver usb-storage [ 0.740720] mousedev: PS/2 mouse device common for all mice [ 0.747352] sdhci: Secure Digital Host Controller Interface driver [ 0.753557] sdhci: Copyright(c) Pierre Ossman [ 0.757971] Synopsys Designware Multimedia Card Interface Driver [ 0.764158] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.770047] mmc0: Unknown controller version (3). You may experience problems. [ 0.811919] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.820170] ledtrig-cpu: registered to indicate activity on CPUs [ 0.826827] usbcore: registered new interface driver usbhid [ 0.832434] usbhid: USB HID core driver [ 0.837417] NET: Registered protocol family 17 [ 0.842034] 9pnet: Installing 9P2000 support [ 0.846450] Key type dns_resolver registered [ 0.851630] registered taskstats version 1 [ 0.856154] hctosys: unable to open rtc device (rtc0) [ 0.868277] ALSA device list: [ 0.871240] No soundcards found. [ 0.874963] Waiting for root device /dev/mmcblk0p1... [ 0.911912] mmc0: MAN_BKOPS_EN bit is not set [ 0.936531] mmc0: new HS200 MMC card at address 0001 [ 0.941888] mmcblk0: mmc0:0001 SDW16G 14.7 GiB [ 0.946596] mmcblk0boot0: mmc0:0001 SDW16G partition 1 4.00 MiB [ 0.956694] mmcblk0boot1: mmc0:0001 SDW16G partition 2 4.00 MiB [ 0.962770] mmcblk0rpmb: mmc0:0001 SDW16G partition 3 4.00 MiB [ 0.969934] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 0.984668] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 0.999360] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.007519] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 1.015251] devtmpfs: mounted [ 1.018857] Freeing unused kernel memory: 724K (ffffffc0009b5000 - ffffffc000a6a000) bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#