Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.42 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.95 sec Percent passed so far: 100.0 Final Score: 100.0 ð[0032.477] Enabled early print [0032.480] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0032.485] Processing in recovery mode [0032.489] A02 Bootrom Patch rev = 15 [0032.492] Power-up reason: pmc por [0032.495] Established communication link with host [0033.460] Odmdata from BCT: 0x00084000 [0033.464] DebugPort= 0x3 [0033.466] BoardId read from EEPROM/NCT: 2180 [0033.494] Turned on fan for loki board [0033.498] Key release before reqd. time for fastboot [0033.502] No Battery Present [0033.505] RamCode = 0 [0033.507] Platform has Ddr4 type ram [0033.511] max77620 disabling SD1 Remote Sense [0033.515] Setting Ddr voltage to 1125mv [0033.519] Serial Number of Pmic Max77663: 0x1109e2 [0033.527] Entering ramdump check [0033.530] Get RamDumpCarveOut = 0x0 [0033.533] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0033.538] Last reboot was clean, booting normally! [0033.543] Sdram initialization is successful [0033.547] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0033.552] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0033.557] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0033.563] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0033.568] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0033.573] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0033.578] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0033.583] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0033.599] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0033.604] Platform-DebugCarveout: 0 [0033.608] Downloaded Bct successfully [0033.702] Downloaded bootloader successfully at 0x92c00000 [0033.795] Downloaded rp1 successfully at 0x83000000 [0033.834] MAX77620_GPIO1 Configured. [0033.838] MAX77620_GPIO5 Configured. [0033.841] CPU power rail is up [0033.844] CPU clock enabled [0033.848] Performing RAM repair [0033.851] Updating A64 Warmreset Address to 0x92c002e9 [0033.857] Enable APE clock/reset [0033.860] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0033.865] Loading Secure OS image failed. [0033.869] Set NvDecSticky Bits [0033.872] GSC1 address : ff700000 [0033.876] GSC2 address ff63fffc value c0edbbcc [0033.881] GSC2 address : ff600000 [0033.884] GSC3 address : ff500000 [0033.888] GSC4 address : ff400000 [0033.892] GSC5 address : ff300000 [0033.895] GSC MC Settings done [0033.898] NvTbootPackSdramParams: start. [0033.903] NvTbootPackSdramParams: done. [0033.907] Next binary entry address: 0x92c00258 [0033.911] BoardId: 2180 [0033.914] dram memory type is 3 [0033.917] Tegraboot started after 33256975 us [0033.921] Basic modules init took -33256975 us [0033.926] USB data transfer took 0 us [0033.929] Carveout took 34727861 us [0033.932] CPU initialization took 3629 us [0033.936] Total time taken by TegraBoot 1474515 us [0033.941] Starting CPU & Halting co-processor [0034.765] [0034.766] Debug Init done [0034.768] Marked DTB cacheable [0034.771] Bootloader DTB loaded at 0x83000000 [0034.776] DeviceTree Init done [0034.790] Pinmux applied successfully [0034.795] gicd_base: 0x50041000 [0034.799] gicc_base: 0x50042000 [0034.802] Interrupts Init done [0034.806] Using base:0x60005008 & irq:33 for tick-timer [0034.811] Using base:0x60005000 for delay-timer [0034.816] platform_init_timer: DONE [0034.819] Timer(tick) Init done [0034.824] osc freq = 38400 khz [0034.828] [0034.829] welcome to cboot [0034.832] [0034.833] Cboot Version: 24.00.2015.42-t210-63d15635 [0034.838] calling constructors [0034.841] initializing heap [0034.843] initializing threads [0034.846] initializing timers [0034.849] creating bootstrap completion thread [0034.854] top of bootstrap2() [0034.857] CPU: ARM Cortex A57 [0034.859] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0034.864] initializing platform [0034.890] config for ddr50 mode completed [0034.894] sdmmc bdev is already initialized [0034.898] of_register: registering tegra_udc to of_hal [0034.904] of_register: registering inv20628-driver to of_hal [0034.909] of_register: registering ads1015-driver to of_hal [0034.915] of_register: registering lp8557-bl-driver to of_hal [0034.920] of_register: registering bq2419x_charger to of_hal [0034.926] of_register: registering cpc to of_hal [0034.931] of_register: registering bq27441_fuel_gauge to of_hal [0034.945] gpio framework initialized [0034.948] of_register: registering tca9539_gpio to of_hal [0034.954] of_register: registering tca9539_gpio to of_hal [0034.959] of_register: registering i2c_bus_driver to of_hal [0034.965] of_register: registering i2c_bus_driver to of_hal [0034.970] of_register: registering i2c_bus_driver to of_hal [0034.976] pmic framework initialized [0034.979] of_register: registering max77620_pmic to of_hal [0034.985] regulator framework initialized [0034.989] of_register: registering tps65132_bl_driver to of_hal [0034.995] of_register: registering tegra_xhci to of_hal [0035.000] initializing target [0035.006] gpio_driver_register: register 'tegra_gpio_driver' driver [0035.016] fixed regulator driver initialized [0035.081] initializing OF layer [0035.085] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0035.093] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.115] I2C Bus Init done [0035.118] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.130] I2C Bus Init done [0035.132] of_children_init: Ops found for compatible string ti,lp8557 [0035.140] of_children_init: Ops found for compatible string ti,tca9539 [0035.151] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0035.156] gpio_driver_register: register 'tca9539_gpio_driver' driver [0035.163] of_children_init: Ops found for compatible string ti,tca9539 [0035.174] tca9539_init: i2c bus: 2, slave addr: 0xee [0035.179] gpio_driver_register: register 'tca9539_gpio_driver' driver [0035.186] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.198] I2C Bus Init done [0035.200] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.212] I2C Bus Init done [0035.215] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.227] I2C Bus Init done [0035.230] of_children_init: Ops found for compatible string maxim,max77620 [0035.242] max77620_init using irq 118 [0035.247] register 'maxim,max77620' pmic [0035.251] gpio_driver_register: register 'max77620-gpio' driver [0035.258] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.270] I2C Bus Init done [0035.272] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0035.281] calling apps_init() [0035.286] Found 19 GPT partitions in "sdmmc3_user" [0035.291] Proceeding to flashing Server [0035.295] usbdcd_reinit Initialize driver to use already enumerated device [0035.302] nv3p_priv_usbf_open USB configuration success [0035.309] Writing GPT partition [0035.313] Erasing Boot device [0035.339] Erasing Storage Device [0035.599] Sanitizing Storage Device [0035.752] Writing protective mbr [0035.756] Writing primary GPT [0035.762] Writing secondary GPT [0035.767] Found 18 GPT partitions in "sdmmc3_user" [0035.773] Writing NVC partition [0035.776] bct_init bctinit [0035.779] bct_init bctinit [0035.787] bct_init bctinit [0035.789] bct_init bctinit [0035.792] bct_init bctinit [0035.833] partition NVC write successful. [0035.837] Writing APP partition [0035.840] bct_init bctinit [0036.692] bct_init bctinit [0036.694] bct_init bctinit [0037.312] partition APP write successful. [0037.317] Writing TBC partition [0037.320] bct_init bctinit [0037.325] bct_init bctinit [0037.328] bct_init bctinit [0037.333] partition TBC write successful. [0037.338] Writing EBT partition [0037.341] bct_init bctinit [0037.360] bct_init bctinit [0037.363] bct_init bctinit [0037.381] partition EBT write successful. [0037.386] Writing BPF partition [0037.389] bct_init bctinit [0037.394] bct_init bctinit [0037.396] bct_init bctinit [0037.402] partition BPF write successful. [0037.406] Writing WB0 partition [0037.409] bct_init bctinit [0037.413] bct_init bctinit [0037.415] bct_init bctinit [0037.420] partition WB0 write successful. [0037.424] Writing RP1 partition [0037.427] bct_init bctinit [0037.443] bct_init bctinit [0037.446] bct_init bctinit [0037.457] partition RP1 write successful. [0037.462] Writing TOS partition [0037.465] bct_init bctinit [0037.470] bct_init bctinit [0037.473] bct_init bctinit [0037.478] partition TOS write successful. [0037.483] Writing DTB partition [0037.486] bct_init bctinit [0037.502] bct_init bctinit [0037.504] bct_init bctinit [0037.514] partition DTB write successful. [0037.521] Writing BCT partition [0037.525] bct_init bctinit [0037.627] partition BCT write successful. [0037.635] Change state to cold boot mode [0037.638] Flushing data to stroage [0000.154] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.159] Processing in cold boot mode Bootloader 2 [0000.164] A02 Bootrom Patch rev = 15 [0000.167] Power-up reason: software reset [0000.171] No Battery Present [0000.174] RamCode = 0 [0000.176] Platform has Ddr4 type ram [0000.179] max77620 disabling SD1 Remote Sense [0000.184] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0x1109e2 [0000.195] Entering ramdump check [0000.198] Get RamDumpCarveOut = 0x0 [0000.201] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.207] Last reboot was clean, booting normally! [0000.211] Sdram initialization is successful [0000.215] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.221] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.226] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.231] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.236] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.241] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.246] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.252] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.267] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.272] Platform-DebugCarveout: 0 [0000.276] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.281] Non secure mode. Disable rollback prevention [0000.286] AOTAG Init Done [0000.313] Using GPT Primary to query partitions [0000.318] Loading Tboot-CPU binary [0000.367] Verifying bootloader in OdmNonSecureSBK mode [0000.377] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.384] Bootloader downloaded successfully. [0000.388] Downloaded Tboot-CPU binary to 0xa0000258 [0000.393] MAX77620_GPIO1 Configured. [0000.397] MAX77620_GPIO5 Configured. [0000.400] CPU power rail is up [0000.403] CPU clock enabled [0000.407] Performing RAM repair [0000.410] Updating A64 Warmreset Address to 0xa00002e9 [0000.427] Bootloader DTB Load Address: 0x83000000 [0000.444] Kernel DTB Load Address: 0x83080000 [0000.449] Loading cboot binary [0000.542] Verifying bootloader in OdmNonSecureSBK mode [0000.648] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.655] Bootloader downloaded successfully. [0000.659] GPT: Partition NOT found ! [0000.663] Find Partition via GPT Failed [0000.666] Find Partition via PT Failed [0000.670] function NvTbootGetBinaryOffsets: 0x1 error [0000.675] Error in NvTbootLoadBinary: 0x1 ! [0000.679] Next binary entry address: 0x80110000 [0000.683] BoardId: 2180 [0000.688] dram memory type is 3 [0000.692] WB0 init successful [0000.718] Bpmp FW successfully loaded [0000.721] Set NvDecSticky Bits [0000.725] GSC1 address : ff700000 [0000.728] GSC2 address ff63fffc value c0edbbcc [0000.733] GSC2 address : ff600000 [0000.737] GSC3 address : ff500000 [0000.740] GSC4 address : ff400000 [0000.744] GSC5 address : ff300000 [0000.747] GSC MC Settings done [0000.751] TOS old plaintext Image length 65536 [0000.757] *** Secure OS image signature not verified *** [0000.762] Loading and Validation of Secure OS Successful [0000.767] NvTbootPackSdramParams: start. [0000.772] NvTbootPackSdramParams: done. [0000.776] Tegraboot started after 133085 us [0000.780] Basic modules init took 292487 us [0000.784] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.790] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.797] Next stage binary read took 12217 us [0000.801] Carveout took 264531 us [0000.804] CPU initialization took 92779 us [0000.808] Total time taken by TegraBoot 662014 us [0000.813] Starting CPU & Halting co-processor 64b[0000.920] RamCode = 0 [0000.936] LPDDR4 Training: Read DT: Number of tables = 10 [0000.941] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.946] EMC Training Skipped [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.954] EMC Training Skipped [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.962] EMC Training Skipped [0000.965] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.970] EMC Training Skipped [0000.973] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.979] EMC Training Successful [0000.982] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.988] EMC Training Successful [0000.991] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.002] EMC Training Successful [0001.005] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.028] EMC Training Successful [0001.031] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.053] EMC Training Successful [0001.056] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.075] EMC Training Successful [0001.078] Switching to 800000 KHz Success [0001.084] DT Write: emc-table@40800 succeeded [0001.091] DT Write: emc-table@68000 succeeded [0001.097] DT Write: emc-table@102000 succeeded [0001.104] DT Write: emc-table@204000 succeeded [0001.110] DT Write: emc-table@408000 succeeded [0001.116] DT Write: emc-table@665600 succeeded [0001.123] DT Write: emc-table@800000 succeeded [0001.129] DT Write: emc-table@1065600 succeeded [0001.135] DT Write: emc-table@1331200 succeeded [0001.142] DT Write: emc-table@1600000 succeeded [0001.146] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 Þò[0000.122] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.127] Processing in cold boot mode Bootloader 2 [0000.132] A02 Bootrom Patch rev = 15 [0000.135] Power-up reason: reset button [0000.139] No Battery Present [0000.141] RamCode = 0 [0000.144] Platform has Ddr4 type ram [0000.147] max77620 disabling SD1 Remote Sense [0000.151] Setting Ddr voltage to 1125mv [0000.155] Serial Number of Pmic Max77663: 0x1109e2 [0000.163] Entering ramdump check [0000.166] Get RamDumpCarveOut = 0x0 [0000.169] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.174] Last reboot was clean, booting normally! [0000.179] Sdram initialization is successful [0000.183] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.204] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.209] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.214] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.219] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.235] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.240] Platform-DebugCarveout: 0 [0000.243] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.253] AOTAG Init Done [0000.281] Using GPT Primary to query partitions [0000.286] Loading Tboot-CPU binary [0000.335] Verifying bootloader in OdmNonSecureSBK mode [0000.345] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.352] Bootloader downloaded successfully. [0000.356] Downloaded Tboot-CPU binary to 0xa0000258 [0000.361] MAX77620_GPIO1 Configured. [0000.365] MAX77620_GPIO5 Configured. [0000.368] CPU power rail is up [0000.371] CPU clock enabled [0000.375] Performing RAM repair [0000.378] Updating A64 Warmreset Address to 0xa00002e9 [0000.395] Bootloader DTB Load Address: 0x83000000 [0000.411] Kernel DTB Load Address: 0x83080000 [0000.416] Loading cboot binary [0000.510] Verifying bootloader in OdmNonSecureSBK mode [0000.616] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.623] Bootloader downloaded successfully. [0000.627] GPT: Partition NOT found ! [0000.630] Find Partition via GPT Failed [0000.634] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.642] Error in NvTbootLoadBinary: 0x1 ! [0000.646] Next binary entry address: 0x80110000 [0000.651] BoardId: 2180 [0000.656] dram memory type is 3 [0000.659] WB0 init successful [0000.685] Bpmp FW successfully loaded [0000.689] Set NvDecSticky Bits [0000.692] GSC1 address : ff700000 [0000.696] GSC2 address ff63fffc value c0edbbcc [0000.700] GSC2 address : ff600000 [0000.704] GSC3 address : ff500000 [0000.708] GSC4 address : ff400000 [0000.712] GSC5 address : ff300000 [0000.715] GSC MC Settings done [0000.718] TOS old plaintext Image length 65536 [0000.725] *** Secure OS image signature not verified *** [0000.730] Loading and Validation of Secure OS Successful [0000.735] NvTbootPackSdramParams: start. [0000.740] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 100049 us [0000.747] Basic modules init took 292262 us [0000.751] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.757] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.765] Next stage binary read took 12217 us [0000.769] Carveout took 264524 us [0000.772] CPU initialization took 92779 us [0000.776] Total time taken by TegraBoot 661782 us [0000.781] Starting CPU & Halting co-processor 64b[0000.888] RamCode = 0 [0000.903] LPDDR4 Training: Read DT: Number of tables = 10 [0000.908] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.913] EMC Training Skipped [0000.916] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.921] EMC Training Skipped [0000.924] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.929] EMC Training Skipped [0000.932] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.937] EMC Training Skipped [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.946] EMC Training Successful [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.955] EMC Training Successful [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.970] EMC Training Successful [0000.973] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.995] EMC Training Successful [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.020] EMC Training Successful [0001.023] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.043] EMC Training Successful [0001.046] Switching to 800000 KHz Success [0001.052] DT Write: emc-table@40800 succeeded [0001.058] DT Write: emc-table@68000 succeeded [0001.065] DT Write: emc-table@102000 succeeded [0001.071] DT Write: emc-table@204000 succeeded [0001.077] DT Write: emc-table@408000 succeeded [0001.084] DT Write: emc-table@665600 succeeded [0001.090] DT Write: emc-table@800000 succeeded [0001.097] DT Write: emc-table@1065600 succeeded [0001.103] DT Write: emc-table@1331200 succeeded [0001.109] DT Write: emc-table@1600000 succeeded [0001.114] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915468 bytes read in 209 ms (31.6 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 448 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3587/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 62 ms (830.1 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.451167] console [ttyS0] enabled [ 0.451167] console [ttyS0] enabled [ 0.458929] bootconsole [uart0] disabled [ 0.458929] bootconsole [uart0] disabled [ 0.467435] SuperH (H)SCI(F) driver initialized [ 0.472308] msm_serial: driver initialized [ 0.476938] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.487217] loop: module loaded [ 0.491641] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.503392] max77620-sd0: supplied by regulator-dummy [ 0.509730] max77620-sd1: supplied by regulator-dummy [ 0.515865] max77620-sd2: supplied by regulator-dummy [ 0.521788] max77620-sd3: supplied by regulator-dummy [ 0.528190] max77620-ldo0: supplied by regulator-dummy [ 0.534245] max77620-ldo1: supplied by regulator-dummy [ 0.539991] max77620-ldo2: supplied by regulator-dummy [ 0.545999] max77620-ldo3: supplied by regulator-dummy [ 0.551157] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.558031] max77620-ldo4: supplied by regulator-dummy [ 0.563206] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.569779] max77620-ldo5: supplied by regulator-dummy [ 0.574938] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.581924] max77620-ldo6: supplied by regulator-dummy [ 0.587083] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.593962] max77620-ldo7: supplied by regulator-dummy [ 0.599945] max77620-ldo8: supplied by regulator-dummy [ 0.610523] libphy: Fixed MDIO Bus: probed [ 0.615017] tun: Universal TUN/TAP device driver, 1.6 [ 0.620678] thunder_xcv, ver 1.0 [ 0.623941] thunder_bgx, ver 1.0 [ 0.627203] nicpf, ver 1.0 [ 0.630171] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.636002] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.641950] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.648908] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.654501] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.662324] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.668490] sky2: driver version 1.30 [ 0.672445] usbcore: registered new interface driver r8152 [ 0.678027] VFIO - User Level meta-driver version: 0.3 [ 0.683968] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.690494] ehci-pci: EHCI PCI platform driver [ 0.694962] ehci-platform: EHCI generic platform driver [ 0.700282] ehci-orion: EHCI orion driver [ 0.704369] ehci-exynos: EHCI EXYNOS driver [ 0.708627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.714812] ohci-pci: OHCI PCI platform driver [ 0.719282] ohci-platform: OHCI generic platform driver [ 0.724591] ohci-exynos: OHCI EXYNOS driver [ 0.729287] usbcore: registered new interface driver usb-storage [ 0.868216] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.876461] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.883623] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.889929] i2c /dev entries driver [ 0.896217] sdhci: Secure Digital Host Controller Interface driver [ 0.902397] sdhci: Copyright(c) Pierre Ossman [ 0.906911] Synopsys Designware Multimedia Card Interface Driver [ 0.913524] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.919432] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.940703] mmc0: Unknown controller version (3). You may experience problems. [ 0.978611] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.987570] ledtrig-cpu: registered to indicate activity on CPUs [ 0.994468] usbcore: registered new interface driver usbhid [ 1.000093] usbhid: USB HID core driver [ 1.005598] NET: Registered protocol family 17 [ 1.010118] 9pnet: Installing 9P2000 support [ 1.014453] Key type dns_resolver registered [ 1.019211] registered taskstats version 1 [ 1.023378] Loading compiled-in X.509 certificates [ 1.035746] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.040671] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.046463] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.051782] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.057712] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.064415] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.069670] RTL_5V: supplied by VDD_5V0_SYS [ 1.074093] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.080188] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.085151] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.098271] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.105245] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.112065] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.118866] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.126372] mmc0: new high speed MMC card at address 0001 [ 1.132324] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.137331] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.143686] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.149739] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.157403] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.164381] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.171422] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.179179] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.580742] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.989835] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.398930] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.406428] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.411925] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.420120] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.821695] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.230764] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.639835] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.647331] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.652912] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.659181] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.665361] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.672230] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.679535] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.685515] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.693597] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.702928] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.770146] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777547] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.782961] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791523] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.800161] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806590] hub 1-0:1.0: USB hub found [ 3.810373] hub 1-0:1.0: 5 ports detected [ 3.814717] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.820122] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827741] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.836131] hub 2-0:1.0: USB hub found [ 3.839904] hub 2-0:1.0: 4 ports detected [ 3.845064] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.858159] mmc1: Unknown controller version (3). You may experience problems. [ 3.897011] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.905155] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.917330] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.925015] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.931991] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.944153] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.957826] max77686-rtc max77620-rtc: setting system clock to 2018-02-11 23:46:10 UTC (1518392770) [ 4.178001] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.204701] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.217346] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.342388] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.402556] r8152 2-1:1.0 eth0: v1.09.9 [ 4.406608] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.418733] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.292492] r8152 2-1:1.0 eth0: carrier on [ 7.321495] IP-Config: Complete: [ 7.324741] device=eth0, hwaddr=00:04:4b:56:bc:27, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.334905] host=192.168.99.2, domain=, nis-domain=(none) [ 7.340732] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.348158] AVDD_DSI_CSI_1V2: disabling [ 7.352012] VDD_PRE_REG_1V35: disabling [ 7.355882] VDD_CAM_HV: disabling [ 7.359331] VDD_TS_HV: disabling [ 7.362687] VDD_TS_1V8: disabling [ 7.366008] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.370365] VDD_3V3_SD: disabling [ 7.373680] VDD_HDMI_5V0: disabling [ 7.377158] ALSA device list: [ 7.380122] No soundcards found. [ 7.384235] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 23:46:13 ] L4T-INITRD Build DATE: Sun Feb 11 23:46:13 UTC 2018 [ 23:46:13 ] Root device found: nfs [ 23:46:13 ] Ethernet interfaces: eth0 [ 23:46:13 ] IP Address: 192.168.99.2 [ 23:46:13 ] Rootfs mounted over nfs [ 23:46:13 ] Switching from initrd to actual rootfs [ 8.082116] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.100465] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.130970] systemd[1]: Set hostname to . [ 8.553077] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.573567] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.589671] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.605722] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 8.621668] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.641586] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.657622] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. Mounting RPC Pipe File System... [ OK ] Reached target Encrypted Volumes. Mounting Huge Pages File System... Starting Remount Root and Kernel File Systems... [ OK ] Created slice system-serial\x2dgetty.slice. Starting Load Kernel Modules... [ OK ] Listening on Syslog Socket. [ OK ] Reached target Paths. Mounting POSIX Message Queue File System... Starting Create Static Device Nodes in /dev... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... Mounting Debug File System... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. Starting Raise network interfaces... [ OK ] Started Preprocess NFS configuration. [ 9.353349] systemd-journald[1569]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Found device /dev/ttyS0. [ 10.046545] random: crng init done [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Permit User Sessions... [ OK ] Started Regular background program processing daemon. Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting System Logging Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting LSB: Start NTP daemon... [ OK ] Started D-Bus System Message Bus. Starting Login Service... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: þü[0000.122] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.127] Processing in cold boot mode Bootloader 2 [0000.132] A02 Bootrom Patch rev = 15 [0000.135] Power-up reason: reset button [0000.139] No Battery Present [0000.141] RamCode = 0 [0000.144] Platform has Ddr4 type ram [0000.147] max77620 disabling SD1 Remote Sense [0000.151] Setting Ddr voltage to 1125mv [0000.155] Serial Number of Pmic Max77663: 0x1109e2 [0000.163] Entering ramdump check [0000.166] Get RamDumpCarveOut = 0x0 [0000.169] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.174] Last reboot was clean, booting normally! [0000.179] Sdram initialization is successful [0000.183] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.204] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.209] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.214] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.219] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.235] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.240] Platform-DebugCarveout: 0 [0000.243] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.253] AOTAG Init Done [0000.281] Using GPT Primary to query partitions [0000.286] Loading Tboot-CPU binary [0000.335] Verifying bootloader in OdmNonSecureSBK mode [0000.345] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.352] Bootloader downloaded successfully. [0000.356] Downloaded Tboot-CPU binary to 0xa0000258 [0000.361] MAX77620_GPIO1 Configured. [0000.365] MAX77620_GPIO5 Configured. [0000.368] CPU power rail is up [0000.371] CPU clock enabled [0000.375] Performing RAM repair [0000.378] Updating A64 Warmreset Address to 0xa00002e9 [0000.395] Bootloader DTB Load Address: 0x83000000 [0000.411] Kernel DTB Load Address: 0x83080000 [0000.416] Loading cboot binary [0000.510] Verifying bootloader in OdmNonSecureSBK mode [0000.616] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.623] Bootloader downloaded successfully. [0000.627] GPT: Partition NOT found ! [0000.630] Find Partition via GPT Failed [0000.634] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.642] Error in NvTbootLoadBinary: 0x1 ! [0000.646] Next binary entry address: 0x80110000 [0000.651] BoardId: 2180 [0000.656] dram memory type is 3 [0000.659] WB0 init successful [0000.685] Bpmp FW successfully loaded [0000.689] Set NvDecSticky Bits [0000.692] GSC1 address : ff700000 [0000.696] GSC2 address ff63fffc value c0edbbcc [0000.700] GSC2 address : ff600000 [0000.704] GSC3 address : ff500000 [0000.708] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.715] GSC MC Settings done [0000.718] TOS old plaintext Image length 65536 [0000.725] *** Secure OS image signature not verified *** [0000.730] Loading and Validation of Secure OS Successful [0000.735] NvTbootPackSdramParams: start. [0000.740] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 100043 us [0000.747] Basic modules init took 292257 us [0000.751] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.757] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.765] Next stage binary read took 12217 us [0000.769] Carveout took 264523 us [0000.772] CPU initialization took 92779 us [0000.776] Total time taken by TegraBoot 661776 us [0000.781] Starting CPU & Halting co-processor 64b[0000.888] RamCode = 0 [0000.903] LPDDR4 Training: Read DT: Number of tables = 10 [0000.908] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.913] EMC Training Skipped [0000.916] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.921] EMC Training Skipped [0000.924] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.929] EMC Training Skipped [0000.932] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.937] EMC Training Skipped [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.946] EMC Training Successful [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.955] EMC Training Successful [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.970] EMC Training Successful [0000.973] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.995] EMC Training Successful [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.020] EMC Training Successful [0001.023] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.042] EMC Training Successful [0001.046] Switching to 800000 KHz Success [0001.052] DT Write: emc-table@40800 succeeded [0001.058] DT Write: emc-table@68000 succeeded [0001.065] DT Write: emc-table@102000 succeeded [0001.071] DT Write: emc-table@204000 succeeded [0001.077] DT Write: emc-table@408000 succeeded [0001.084] DT Write: emc-table@665600 succeeded [0001.090] DT Write: emc-table@800000 succeeded [0001.097] DT Write: emc-table@1065600 succeeded [0001.103] DT Write: emc-table@1331200 succeeded [0001.109] DT Write: emc-table@1600000 succeeded [0001.114] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915468 bytes read in 208 ms (31.7 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 447 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3587/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 61 ms (843.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.458757] console [ttyS0] enabled [ 0.458757] console [ttyS0] enabled [ 0.465848] bootconsole [uart0] disabled [ 0.465848] bootconsole [uart0] disabled [ 0.474387] SuperH (H)SCI(F) driver initialized [ 0.479277] msm_serial: driver initialized [ 0.483904] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.494353] loop: module loaded [ 0.498749] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.510494] max77620-sd0: supplied by regulator-dummy [ 0.516821] max77620-sd1: supplied by regulator-dummy [ 0.522989] max77620-sd2: supplied by regulator-dummy [ 0.528871] max77620-sd3: supplied by regulator-dummy [ 0.535288] max77620-ldo0: supplied by regulator-dummy [ 0.541362] max77620-ldo1: supplied by regulator-dummy [ 0.547103] max77620-ldo2: supplied by regulator-dummy [ 0.553108] max77620-ldo3: supplied by regulator-dummy [ 0.558281] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.565161] max77620-ldo4: supplied by regulator-dummy [ 0.570317] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.576895] max77620-ldo5: supplied by regulator-dummy [ 0.582053] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.589036] max77620-ldo6: supplied by regulator-dummy [ 0.594207] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.601092] max77620-ldo7: supplied by regulator-dummy [ 0.607074] max77620-ldo8: supplied by regulator-dummy [ 0.617717] libphy: Fixed MDIO Bus: probed [ 0.622147] tun: Universal TUN/TAP device driver, 1.6 [ 0.627805] thunder_xcv, ver 1.0 [ 0.631070] thunder_bgx, ver 1.0 [ 0.634317] nicpf, ver 1.0 [ 0.637285] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.643119] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.649068] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.656025] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.661618] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.669441] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.675613] sky2: driver version 1.30 [ 0.679569] usbcore: registered new interface driver r8152 [ 0.685149] VFIO - User Level meta-driver version: 0.3 [ 0.691095] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.697623] ehci-pci: EHCI PCI platform driver [ 0.702091] ehci-platform: EHCI generic platform driver [ 0.707409] ehci-orion: EHCI orion driver [ 0.711492] ehci-exynos: EHCI EXYNOS driver [ 0.715750] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.721933] ohci-pci: OHCI PCI platform driver [ 0.726409] ohci-platform: OHCI generic platform driver [ 0.731716] ohci-exynos: OHCI EXYNOS driver [ 0.736441] usbcore: registered new interface driver usb-storage [ 0.875361] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.883587] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.890763] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.897077] i2c /dev entries driver [ 0.903381] sdhci: Secure Digital Host Controller Interface driver [ 0.909561] sdhci: Copyright(c) Pierre Ossman [ 0.914071] Synopsys Designware Multimedia Card Interface Driver [ 0.920676] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.926600] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.946585] mmc0: Unknown controller version (3). You may experience problems. [ 0.984965] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.993896] ledtrig-cpu: registered to indicate activity on CPUs [ 1.000721] usbcore: registered new interface driver usbhid [ 1.006350] usbhid: USB HID core driver [ 1.011848] NET: Registered protocol family 17 [ 1.016373] 9pnet: Installing 9P2000 support [ 1.020707] Key type dns_resolver registered [ 1.025520] registered taskstats version 1 [ 1.029619] Loading compiled-in X.509 certificates [ 1.041701] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.046692] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.052464] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.057779] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.063728] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.070421] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.071661] mmc0: new high speed MMC card at address 0001 [ 1.075622] RTL_5V: supplied by VDD_5V0_SYS [ 1.081004] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.084917] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.089607] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.095318] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.100218] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.104730] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.110493] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.123458] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.135287] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.136115] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.150350] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.157106] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.165461] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.172252] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.180456] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.582033] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.991124] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.400206] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.407704] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.413196] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.421389] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.822978] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.232057] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.641132] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.648625] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.654197] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.660467] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.666647] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.673518] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.680826] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.686698] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.694870] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.704200] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.775206] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.782607] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.788018] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.796559] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.805195] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.811612] hub 1-0:1.0: USB hub found [ 3.815391] hub 1-0:1.0: 5 ports detected [ 3.819737] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.825143] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.832762] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.841153] hub 2-0:1.0: USB hub found [ 3.844930] hub 2-0:1.0: 4 ports detected [ 3.850100] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.863207] mmc1: Unknown controller version (3). You may experience problems. [ 3.902081] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.910226] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.922389] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.930060] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.937291] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.949488] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.974872] max77686-rtc max77620-rtc: setting system clock to 2018-02-11 23:47:12 UTC (1518392832) [ 4.183063] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.209846] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.222523] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.347453] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.407616] r8152 2-1:1.0 eth0: v1.09.9 [ 4.411666] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.423824] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.361534] r8152 2-1:1.0 eth0: carrier on [ 7.390558] IP-Config: Complete: [ 7.393804] device=eth0, hwaddr=00:04:4b:56:bc:27, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.403969] host=192.168.99.2, domain=, nis-domain=(none) [ 7.409797] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.417222] AVDD_DSI_CSI_1V2: disabling [ 7.421070] VDD_PRE_REG_1V35: disabling [ 7.424935] VDD_CAM_HV: disabling [ 7.428385] VDD_TS_HV: disabling [ 7.431744] VDD_TS_1V8: disabling [ 7.435064] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.439420] VDD_3V3_SD: disabling [ 7.442735] VDD_HDMI_5V0: disabling [ 7.446215] ALSA device list: [ 7.449179] No soundcards found. [ 7.453289] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 23:47:15 ] L4T-INITRD Build DATE: Sun Feb 11 23:47:15 UTC 2018 [ 23:47:15 ] Root device found: nfs [ 23:47:15 ] Ethernet interfaces: eth0 [ 23:47:15 ] IP Address: 192.168.99.2 [ 23:47:15 ] Rootfs mounted over nfs [ 23:47:15 ] Switching from initrd to actual rootfs [ 7.666081] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.684446] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.703454] systemd[1]: Set hostname to . [ 7.951463] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 7.970761] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.986754] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.010719] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.030647] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.046659] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.062881] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. Starting Remount Root and Kernel File Systems... Mounting RPC Pipe File System... Starting Load Kernel Modules... Mounting Huge Pages File System... [ OK ] Reached target Encrypted Volumes. Mounting Debug File System... [ OK ] Reached target Paths. [ OK ] Reached target Swap. Starting Create Static Device Nodes in /dev... [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Audit Socket. Starting Journal Service... Mounting POSIX Message Queue File System... [ OK ] Listening on udev Control Socket. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Reached target Local File Systems (Pre). Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Apply Kernel Variables. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Load/Save Random Seed. [ 8.693922] systemd-journald[1568]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Permit User Sessions... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting LSB: Start NTP daemon... Starting Login Service... [ OK ] Started D-Bus System Message Bus. [ 9.849020] random: crng init done [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ü