Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.26 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.86 sec Percent passed so far: 100.0 Final Score: 100.0 n[0024.402] Enabled early print [0024.405] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0024.410] Processing in recovery mode [0024.414] A02 Bootrom Patch rev = 63 [0024.417] Power-up reason: pmc por [0024.420] Established communication link with host [0025.385] Odmdata from BCT: 0x00084000 [0025.388] DebugPort= 0x3 [0025.391] BoardId read from EEPROM/NCT: 2180 [0025.419] Turned on fan for loki board [0025.422] Key release before reqd. time for fastboot [0025.427] No Battery Present [0025.430] RamCode = 0 [0025.432] Platform has Ddr4 type ram [0025.435] max77620 disabling SD1 Remote Sense [0025.440] Setting Ddr voltage to 1125mv [0025.444] Serial Number of Pmic Max77663: 0x1e06f3 [0025.451] Entering ramdump check [0025.454] Get RamDumpCarveOut = 0x0 [0025.458] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0025.463] Last reboot was clean, booting normally! [0025.467] Sdram initialization is successful [0025.471] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0025.477] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0025.482] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0025.487] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0025.492] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0025.498] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0025.503] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0025.508] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0025.523] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0025.529] Platform-DebugCarveout: 0 [0025.532] Downloaded Bct successfully [0025.626] Downloaded bootloader successfully at 0x92c00000 [0025.731] Downloaded rp1 successfully at 0x83000000 [0025.770] MAX77620_GPIO1 Configured. [0025.773] MAX77620_GPIO5 Configured. [0025.777] CPU power rail is up [0025.780] CPU clock enabled [0025.784] Performing RAM repair [0025.786] Updating A64 Warmreset Address to 0x92c002e9 [0025.793] Enable APE clock/reset [0025.796] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0025.800] Loading Secure OS image failed. [0025.804] Set NvDecSticky Bits [0025.808] GSC1 address : ff700000 [0025.811] GSC2 address ff63fffc value c0edbbcc [0025.816] GSC2 address : ff600000 [0025.820] GSC3 address : ff500000 [0025.823] GSC4 address : ff400000 [0025.827] GSC5 address : ff300000 [0025.830] GSC MC Settings done [0025.833] NvTbootPackSdramParams: start. [0025.838] NvTbootPackSdramParams: done. [0025.842] Next binary entry address: 0x92c00258 [0025.846] BoardId: 2180 [0025.849] dram memory type is 3 [0025.852] Tegraboot started after 24988084 us [0025.857] Basic modules init took -24988084 us [0025.861] USB data transfer took 0 us [0025.864] Carveout took 26469659 us [0025.868] CPU initialization took 3629 us [0025.872] Total time taken by TegraBoot 1485204 us [0025.876] Starting CPU & Halting co-processor [0026.507] [0026.508] Debug Init done [0026.510] Marked DTB cacheable [0026.513] Bootloader DTB loaded at 0x83000000 [0026.517] DeviceTree Init done [0026.532] Pinmux applied successfully [0026.537] gicd_base: 0x50041000 [0026.541] gicc_base: 0x50042000 [0026.543] Interrupts Init done [0026.548] Using base:0x60005008 & irq:33 for tick-timer [0026.553] Using base:0x60005000 for delay-timer [0026.558] platform_init_timer: DONE [0026.561] Timer(tick) Init done [0026.565] osc freq = 38400 khz [0026.570] [0026.571] welcome to cboot [0026.573] [0026.575] Cboot Version: 24.00.2015.42-t210-63d15635 [0026.580] calling constructors [0026.583] initializing heap [0026.585] initializing threads [0026.588] initializing timers [0026.591] creating bootstrap completion thread [0026.595] top of bootstrap2() [0026.598] CPU: ARM Cortex A57 [0026.601] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0026.606] initializing platform [0026.632] config for ddr50 mode completed [0026.636] sdmmc bdev is already initialized [0026.640] of_register: registering tegra_udc to of_hal [0026.645] of_register: registering inv20628-driver to of_hal [0026.651] of_register: registering ads1015-driver to of_hal [0026.656] of_register: registering lp8557-bl-driver to of_hal [0026.662] of_register: registering bq2419x_charger to of_hal [0026.668] of_register: registering cpc to of_hal [0026.672] of_register: registering bq27441_fuel_gauge to of_hal [0026.687] gpio framework initialized [0026.690] of_register: registering tca9539_gpio to of_hal [0026.695] of_register: registering tca9539_gpio to of_hal [0026.701] of_register: registering i2c_bus_driver to of_hal [0026.706] of_register: registering i2c_bus_driver to of_hal [0026.712] of_register: registering i2c_bus_driver to of_hal [0026.718] pmic framework initialized [0026.721] of_register: registering max77620_pmic to of_hal [0026.726] regulator framework initialized [0026.730] of_register: registering tps65132_bl_driver to of_hal [0026.736] of_register: registering tegra_xhci to of_hal [0026.742] initializing target [0026.748] gpio_driver_register: register 'tegra_gpio_driver' driver [0026.758] fixed regulator driver initialized [0026.823] initializing OF layer [0026.827] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0026.835] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.857] I2C Bus Init done [0026.860] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.872] I2C Bus Init done [0026.875] of_children_init: Ops found for compatible string ti,lp8557 [0026.881] I2C slave not started [0026.884] I2C write failed [0026.887] Writing offset failed [0026.890] failed to read 0x 0 [0026.893] lp8557: Couldn't turn off backlight: -3 [0026.897] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0026.911] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0026.917] gpio_driver_register: register 'tca9539_gpio_driver' driver [0026.923] of_children_init: Ops found for compatible string ti,tca9539 [0026.934] tca9539_init: i2c bus: 2, slave addr: 0xee [0026.940] gpio_driver_register: register 'tca9539_gpio_driver' driver [0026.946] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.958] I2C Bus Init done [0026.961] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.973] I2C Bus Init done [0026.975] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.987] I2C Bus Init done [0026.990] of_children_init: Ops found for compatible string maxim,max77620 [0027.002] max77620_init using irq 118 [0027.007] register 'maxim,max77620' pmic [0027.012] gpio_driver_register: register 'max77620-gpio' driver [0027.018] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0027.030] I2C Bus Init done [0027.033] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0027.041] calling apps_init() [0027.047] Found 19 GPT partitions in "sdmmc3_user" [0027.051] Proceeding to flashing Server [0027.055] usbdcd_reinit Initialize driver to use already enumerated device [0027.062] nv3p_priv_usbf_open USB configuration success [0027.069] Writing GPT partition [0027.073] Erasing Boot device [0027.098] Erasing Storage Device [0027.347] Sanitizing Storage Device [0027.463] Writing protective mbr [0027.467] Writing primary GPT [0027.472] Writing secondary GPT [0027.478] Found 18 GPT partitions in "sdmmc3_user" [0027.484] Writing NVC partition [0027.486] bct_init bctinit [0027.489] bct_init bctinit [0027.497] bct_init bctinit [0027.500] bct_init bctinit [0027.502] bct_init bctinit [0027.536] partition NVC write successful. [0027.540] Writing APP partition [0027.543] bct_init bctinit [0028.353] bct_init bctinit [0028.356] bct_init bctinit [0028.967] partition APP write successful. [0028.972] Writing TBC partition [0028.975] bct_init bctinit [0028.980] bct_init bctinit [0028.983] bct_init bctinit [0028.988] partition TBC write successful. [0028.993] Writing EBT partition [0028.996] bct_init bctinit [0029.014] bct_init bctinit [0029.017] bct_init bctinit [0029.027] partition EBT write successful. [0029.032] Writing BPF partition [0029.035] bct_init bctinit [0029.040] bct_init bctinit [0029.043] bct_init bctinit [0029.048] partition BPF write successful. [0029.052] Writing WB0 partition [0029.055] bct_init bctinit [0029.059] bct_init bctinit [0029.061] bct_init bctinit [0029.066] partition WB0 write successful. [0029.070] Writing RP1 partition [0029.073] bct_init bctinit [0029.089] bct_init bctinit [0029.092] bct_init bctinit [0029.101] partition RP1 write successful. [0029.106] Writing TOS partition [0029.109] bct_init bctinit [0029.114] bct_init bctinit [0029.116] bct_init bctinit [0029.124] partition TOS write successful. [0029.129] Writing DTB partition [0029.132] bct_init bctinit [0029.147] bct_init bctinit [0029.150] bct_init bctinit [0029.159] partition DTB write successful. [0029.167] Writing BCT partition [0029.171] bct_init bctinit [0029.264] partition BCT write successful. [0029.272] Change state to cold boot mode [0029.275] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0x1e06f3 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132101 us [0000.779] Basic modules init took 292459 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12210 us [0000.800] Carveout took 264394 us [0000.803] CPU initialization took 92747 us [0000.807] Total time taken by TegraBoot 661810 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 h[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1e06f3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99054 us [0000.746] Basic modules init took 292238 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12210 us [0000.768] Carveout took 264389 us [0000.771] CPU initialization took 92749 us [0000.775] Total time taken by TegraBoot 661586 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 65 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915815 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 16710144 bytes read in 424 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11012/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 57 ms (900.4 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.468409] console [ttyS0] enabled [ 0.468409] console [ttyS0] enabled [ 0.475912] bootconsole [uart0] disabled [ 0.475912] bootconsole [uart0] disabled [ 0.484786] SuperH (H)SCI(F) driver initialized [ 0.489986] msm_serial: driver initialized [ 0.494830] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.505537] loop: module loaded [ 0.510649] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.522465] max77620-sd0: supplied by regulator-dummy [ 0.528846] max77620-sd1: supplied by regulator-dummy [ 0.535023] max77620-sd2: supplied by regulator-dummy [ 0.540949] max77620-sd3: supplied by regulator-dummy [ 0.547357] max77620-ldo0: supplied by regulator-dummy [ 0.553442] max77620-ldo1: supplied by regulator-dummy [ 0.559201] max77620-ldo2: supplied by regulator-dummy [ 0.565238] max77620-ldo3: supplied by regulator-dummy [ 0.570408] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.577320] max77620-ldo4: supplied by regulator-dummy [ 0.582491] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.589075] max77620-ldo5: supplied by regulator-dummy [ 0.594257] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.601263] max77620-ldo6: supplied by regulator-dummy [ 0.606435] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.613350] max77620-ldo7: supplied by regulator-dummy [ 0.619345] max77620-ldo8: supplied by regulator-dummy [ 0.631504] libphy: Fixed MDIO Bus: probed [ 0.638189] tun: Universal TUN/TAP device driver, 1.6 [ 0.644597] thunder-xcv, ver 1.0 [ 0.648384] thunder-BGX, ver 1.0 [ 0.651822] thunder-nic, ver 1.0 [ 0.655481] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.661476] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.667458] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.674477] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.680112] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.687973] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.694248] sky2: driver version 1.30 [ 0.698452] usbcore: registered new interface driver r8152 [ 0.704243] VFIO - User Level meta-driver version: 0.3 [ 0.714552] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.721488] ehci-pci: EHCI PCI platform driver [ 0.726034] ehci-platform: EHCI generic platform driver [ 0.731418] ehci-orion: EHCI orion driver [ 0.735561] ehci-exynos: EHCI EXYNOS driver [ 0.739873] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.746097] ohci-pci: OHCI PCI platform driver [ 0.750600] ohci-platform: OHCI generic platform driver [ 0.755965] ohci-exynos: OHCI EXYNOS driver [ 0.760984] usbcore: registered new interface driver usb-storage [ 0.901293] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.909831] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.917235] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.923630] i2c /dev entries driver [ 0.932539] sdhci: Secure Digital Host Controller Interface driver [ 0.938766] sdhci: Copyright(c) Pierre Ossman [ 0.943540] Synopsys Designware Multimedia Card Interface Driver [ 0.950426] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.956631] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.977437] mmc0: Unknown controller version (3). You may experience problems. [ 1.029409] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.041737] ledtrig-cpu: registered to indicate activity on CPUs [ 1.049695] usbcore: registered new interface driver usbhid [ 1.056117] usbhid: USB HID core driver [ 1.065666] NET: Registered protocol family 17 [ 1.070747] 9pnet: Installing 9P2000 support [ 1.075094] Key type dns_resolver registered [ 1.079926] registered taskstats version 1 [ 1.084253] Loading compiled-in X.509 certificates [ 1.096160] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.101154] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.107068] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.112474] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.118653] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.124267] mmc0: new high speed MMC card at address 0001 [ 1.130158] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.134869] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.140930] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.146892] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.151828] RTL_5V: supplied by VDD_5V0_SYS [ 1.152051] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.161644] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.169492] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.174670] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.187044] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.196080] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.196295] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.196353] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.196404] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.224632] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.234474] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.242688] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.650927] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.059929] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.468940] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.476431] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.481924] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.490115] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.899131] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.308155] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.717171] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.724661] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.730267] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.736575] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.742763] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.749643] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.756964] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.762849] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.770929] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.780285] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.850048] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.857452] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.862861] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.871446] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.880080] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.886573] hub 1-0:1.0: USB hub found [ 3.890435] hub 1-0:1.0: 5 ports detected [ 3.894835] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.900314] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.907961] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.916417] hub 2-0:1.0: USB hub found [ 3.920258] hub 2-0:1.0: 4 ports detected [ 3.925586] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.937535] mmc1: Unknown controller version (3). You may experience problems. [ 3.989474] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.997701] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.009881] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.017537] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.026233] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.038630] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.070430] max77686-rtc max77620-rtc: setting system clock to 2018-01-22 02:15:08 UTC (1516587308) [ 4.257907] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.284686] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.297575] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.422300] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.482629] r8152 2-1:1.0 eth0: v1.09.9 [ 4.486708] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.498815] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.387997] r8152 2-1:1.0 eth0: carrier on [ 7.417403] IP-Config: Complete: [ 7.420653] device=eth0, hwaddr=00:04:4b:66:e6:d7, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.430815] host=192.168.99.2, domain=, nis-domain=(none) [ 7.436641] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.444067] AVDD_DSI_CSI_1V2: disabling [ 7.447920] VDD_PRE_REG_1V35: disabling [ 7.451794] VDD_CAM_HV: disabling [ 7.455249] VDD_TS_HV: disabling [ 7.458594] VDD_TS_1V8: disabling [ 7.461910] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.466265] VDD_3V3_SD: disabling [ 7.469580] VDD_HDMI_5V0: disabling [ 7.473059] ALSA device list: [ 7.476023] No soundcards found. [ 7.480094] Freeing unused kernel memory: 1088K /init: line 58: chmod: command not found [ 02:15:11 ] L4T-INITRD Build DATE: Mon Jan 22 02:15:11 UTC 2018 [ 02:15:11 ] Root device found: nfs [ 02:15:11 ] Ethernet interfaces: eth0 [ 02:15:11 ] IP Address: 192.168.99.2 [ 02:15:11 ] Rootfs mounted over nfs [ 02:15:11 ] Switching from initrd to actual rootfs [ 8.107906] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.126280] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.169011] systemd[1]: Set hostname to . [ 8.576375] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 8.593750] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 8.609599] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.633673] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 8.649522] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.665571] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 8.685517] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice User and Session Slice. [ OK ] Listening on udev Control Socket. [ OK ] Reached target Slices. [ OK ] Listening on Journal Socket. Starting Remount Root and Kernel File Systems... Starting Journal Service... Mounting RPC Pipe File System... Starting Load Kernel Modules... [ OK ] Listening on udev Kernel Socket. Starting Create Static Device Nodes in /dev... Mounting Debug File System... [ OK ] Reached target Swap. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Huge Pages File System... [ OK ] Reached target Encrypted Volumes. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. Mounting POSIX Message Queue File System... [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started udev Kernel Device Manager. [ 9.493197] systemd-journald[1502]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting Permit User Sessions... Starting OpenBSD Secure Shell server... Starting /etc/rc.local Compatibility... Starting System Logging Service... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Started D-Bus System Message Bus. Starting LSB: Start NTP daemon... [ OK ] Started System Logging Service. [ OK ] Started Permit U[ 10.872268] random: crng init done ser Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Getty on tty1. [ OK ] Started Login Service. [ OK ] Found device /dev/ttyS0. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ä[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1e06f3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99049 us [0000.746] Basic modules init took 292241 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12209 us [0000.768] Carveout took 264389 us [0000.771] CPU initialization took 92749 us [0000.775] Total time taken by TegraBoot 661588 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 65 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915815 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 16710144 bytes read in 424 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11012/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 57 ms (900.4 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.471568] console [ttyS0] enabled [ 0.471568] console [ttyS0] enabled [ 0.479144] bootconsole [uart0] disabled [ 0.479144] bootconsole [uart0] disabled [ 0.487931] SuperH (H)SCI(F) driver initialized [ 0.493102] msm_serial: driver initialized [ 0.497986] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.508591] loop: module loaded [ 0.513773] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.525596] max77620-sd0: supplied by regulator-dummy [ 0.531968] max77620-sd1: supplied by regulator-dummy [ 0.538142] max77620-sd2: supplied by regulator-dummy [ 0.544070] max77620-sd3: supplied by regulator-dummy [ 0.550480] max77620-ldo0: supplied by regulator-dummy [ 0.556565] max77620-ldo1: supplied by regulator-dummy [ 0.562330] max77620-ldo2: supplied by regulator-dummy [ 0.568367] max77620-ldo3: supplied by regulator-dummy [ 0.573542] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.580451] max77620-ldo4: supplied by regulator-dummy [ 0.585623] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.592209] max77620-ldo5: supplied by regulator-dummy [ 0.597409] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.604415] max77620-ldo6: supplied by regulator-dummy [ 0.609584] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.616498] max77620-ldo7: supplied by regulator-dummy [ 0.622492] max77620-ldo8: supplied by regulator-dummy [ 0.634590] libphy: Fixed MDIO Bus: probed [ 0.641259] tun: Universal TUN/TAP device driver, 1.6 [ 0.647663] thunder-xcv, ver 1.0 [ 0.651204] thunder-BGX, ver 1.0 [ 0.654846] thunder-nic, ver 1.0 [ 0.658547] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.664516] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.670499] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.677499] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.683155] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.691020] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.697297] sky2: driver version 1.30 [ 0.701542] usbcore: registered new interface driver r8152 [ 0.707329] VFIO - User Level meta-driver version: 0.3 [ 0.717652] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.724529] ehci-pci: EHCI PCI platform driver [ 0.729035] ehci-platform: EHCI generic platform driver [ 0.734416] ehci-orion: EHCI orion driver [ 0.738608] ehci-exynos: EHCI EXYNOS driver [ 0.742926] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.749151] ohci-pci: OHCI PCI platform driver [ 0.753657] ohci-platform: OHCI generic platform driver [ 0.759025] ohci-exynos: OHCI EXYNOS driver [ 0.764047] usbcore: registered new interface driver usb-storage [ 0.904315] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.912850] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.920263] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.926657] i2c /dev entries driver [ 0.935255] sdhci: Secure Digital Host Controller Interface driver [ 0.941868] sdhci: Copyright(c) Pierre Ossman [ 0.946591] Synopsys Designware Multimedia Card Interface Driver [ 0.953566] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.959727] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.981014] mmc0: Unknown controller version (3). You may experience problems. [ 1.033388] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.045719] ledtrig-cpu: registered to indicate activity on CPUs [ 1.053656] usbcore: registered new interface driver usbhid [ 1.060078] usbhid: USB HID core driver [ 1.069505] NET: Registered protocol family 17 [ 1.074592] 9pnet: Installing 9P2000 support [ 1.078938] Key type dns_resolver registered [ 1.083761] registered taskstats version 1 [ 1.088087] Loading compiled-in X.509 certificates [ 1.100032] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.105030] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.110947] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.116351] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.122510] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.128141] mmc0: new high speed MMC card at address 0001 [ 1.133997] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.138711] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.144773] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.150740] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.155681] RTL_5V: supplied by VDD_5V0_SYS [ 1.155909] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.165507] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.173302] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.178492] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.190866] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.199888] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.200104] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.200164] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.200212] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.228431] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.238231] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.246446] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.654851] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.063853] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.472853] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.480346] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.485837] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.494029] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.903022] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.312019] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.721016] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.728505] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.734114] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.740421] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.746609] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.753489] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.760805] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.766706] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.774792] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.784150] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.854028] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.861434] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.866842] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.875445] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.884076] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.890563] hub 1-0:1.0: USB hub found [ 3.894424] hub 1-0:1.0: 5 ports detected [ 3.898823] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.904298] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.911951] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.920404] hub 2-0:1.0: USB hub found [ 3.924245] hub 2-0:1.0: 4 ports detected [ 3.929567] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.941518] mmc1: Unknown controller version (3). You may experience problems. [ 3.993452] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 4.001677] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.013859] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.021529] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.030189] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.042601] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.074382] max77686-rtc max77620-rtc: setting system clock to 2018-01-22 02:16:09 UTC (1516587369) [ 4.261885] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.288682] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.301559] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.426279] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.486601] r8152 2-1:1.0 eth0: v1.09.9 [ 4.490674] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.502762] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.423992] r8152 2-1:1.0 eth0: carrier on [ 7.453384] IP-Config: Complete: [ 7.456629] device=eth0, hwaddr=00:04:4b:66:e6:d7, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.466790] host=192.168.99.2, domain=, nis-domain=(none) [ 7.472616] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.480041] AVDD_DSI_CSI_1V2: disabling [ 7.483895] VDD_PRE_REG_1V35: disabling [ 7.487771] VDD_CAM_HV: disabling [ 7.491224] VDD_TS_HV: disabling [ 7.494570] VDD_TS_1V8: disabling [ 7.497885] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.502239] VDD_3V3_SD: disabling [ 7.505553] VDD_HDMI_5V0: disabling [ 7.509033] ALSA device list: [ 7.511998] No soundcards found. [ 7.516068] Freeing unused kernel memory: 1088K /init: line 58: chmod: command not found [ 02:16:12 ] L4T-INITRD Build DATE: Mon Jan 22 02:16:12 UTC 2018 [ 02:16:12 ] Root device found: nfs [ 02:16:12 ] Ethernet interfaces: eth0 [ 02:16:12 ] IP Address: 192.168.99.2 [ 02:16:12 ] Rootfs mounted over nfs [ 02:16:12 ] Switching from initrd to actual rootfs [ 7.771437] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.789860] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.810293] systemd[1]: Set hostname to . [ 8.097272] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 8.113591] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.137593] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.153474] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.169437] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.185693] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 8.201656] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket. Mounting Huge Pages File System... Mounting RPC Pipe File System... Mounting Debug File System... Starting Create Static Device Nodes in /dev... [ OK ] Listening on Syslog Socket. Starting Load Kernel Modules... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Audit Socket. Starting Journal Service... Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Started Forward Password Requests to Wall Directory Watch. Mounting POSIX Message Queue File System... [ OK ] Reached target Paths. [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Mounting Configuration File System... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started udev Kernel Device Manager. [ 8.903003] systemd-journald[1510]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting Login Service... [ OK ] Started D-Bus System Message Bus. Starting /etc/rc.local Compatibility... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. Starting Permit User Sessions... [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started Getty on tty1. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Found device /dev/ttyS0. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ 11.003109] random: crng init done Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: þ