U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.tegra_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.tegra_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################### 4 MiB/s done Bytes transferred = 6169040 (5e21d0 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x5e21d0 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.15.0-rc7-15575-gb2cd1df (jonathanh@kaivo) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP PREEMPT Sun Jan 7 15:08:02 PST 2018 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0xfbc00000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39168 r8192 d22272 u69632 [ 0.000000] pcpu-alloc: s39168 r8192 d22272 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1998492K/2096128K available (9216K kernel code, 778K rwdata, 2560K rodata, 1024K init, 299K bss, 32100K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 779 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 300 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.007476] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.017005] Switching to timer-based delay loop, resolution 1000ns [ 0.024186] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.029228] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.039976] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.047944] Switching to timer-based delay loop, resolution 83ns [ 0.054393] Console: colour dummy device 80x30 [ 0.058360] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.068668] pid_max: default: 32768 minimum: 301 [ 0.073729] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.079853] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.087699] CPU: Testing write buffer coherency: ok [ 0.092022] /cpus/cpu@0 missing clock-frequency property [ 0.097027] /cpus/cpu@1 missing clock-frequency property [ 0.102337] /cpus/cpu@2 missing clock-frequency property [ 0.107602] /cpus/cpu@3 missing clock-frequency property [ 0.112873] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152987] Setting up static identity map for 0x80100000 - 0x801000a0 [ 0.157741] Hierarchical SRCU implementation. [ 0.173511] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.193008] smp: Bringing up secondary CPUs ... [ 0.243637] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.323749] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.403865] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.413443] smp: Brought up 1 node, 4 CPUs [ 0.432530] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.438697] CPU: All CPU(s) started in SVC mode. [ 0.445150] devtmpfs: initialized [ 0.465090] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.471193] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.480647] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.488122] pinctrl core: initialized pinctrl subsystem [ 0.493178] NET: Registered protocol family 16 [ 0.497868] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.504561] cpuidle: using governor menu [ 0.530466] No ATAGs? [ 0.530605] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.538965] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.546651] iommu: Adding device reg-dummy to group 0 [ 0.549854] iommu: Adding device 1003000.pcie to group 1 [ 0.555156] iommu: Adding device 50000000.host1x to group 2 [ 0.560712] iommu: Adding device 54200000.dc to group 3 [ 0.565893] iommu: Adding device 54240000.dc to group 4 [ 0.571079] iommu: Adding device 54280000.hdmi to group 5 [ 0.576467] iommu: Adding device 57000000.gpu to group 6 [ 0.581739] iommu: Adding device 60005000.timer to group 7 [ 0.587171] iommu: Adding device 60007000.flow-controller to group 8 [ 0.593518] iommu: Adding device 6000c800.actmon to group 9 [ 0.599046] iommu: Adding device 6000d000.gpio to group 10 [ 0.604523] iommu: Adding device 60020000.dma to group 11 [ 0.609896] iommu: Adding device 70000800.apbmisc to group 12 [ 0.615618] iommu: Adding device 70000868.pinmux to group 13 [ 0.621237] iommu: Adding device 70006000.serial to group 14 [ 0.626884] iommu: Adding device 70006040.serial to group 15 [ 0.632498] iommu: Adding device 70006300.serial to group 16 [ 0.638151] iommu: Adding device 7000c000.i2c to group 17 [ 0.643504] iommu: Adding device 7000c400.i2c to group 18 [ 0.648894] iommu: Adding device 7000c500.i2c to group 19 [ 0.654253] iommu: Adding device 7000c700.i2c to group 20 [ 0.659649] iommu: Adding device 7000d000.i2c to group 21 [ 0.664999] iommu: Adding device 7000d400.spi to group 22 [ 0.670395] iommu: Adding device 7000da00.spi to group 23 [ 0.675747] iommu: Adding device 7000e000.rtc to group 24 [ 0.681137] iommu: Adding device 7000e400.pmc to group 25 [ 0.686490] iommu: Adding device 7000f800.fuse to group 26 [ 0.691969] iommu: Adding device 70019000.memory-controller to group 27 [ 0.698540] iommu: Adding device 7001b000.emc to group 28 [ 0.703934] iommu: Adding device 70027000.sata to group 29 [ 0.709371] iommu: Adding device 70030000.hda to group 30 [ 0.714766] iommu: Adding device 70090000.usb to group 31 [ 0.720119] iommu: Adding device 7009f000.padctl to group 32 [ 0.725784] iommu: Adding device 700b0400.sdhci to group 33 [ 0.731297] iommu: Adding device 700b0600.sdhci to group 34 [ 0.736863] iommu: Adding device 70015000.cec to group 35 [ 0.742230] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.748567] iommu: Adding device 70110000.clock to group 37 [ 0.754092] iommu: Adding device 70300000.ahub to group 38 [ 0.759572] iommu: Adding device 7d000000.usb to group 39 [ 0.764925] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.770663] iommu: Adding device 7d004000.usb to group 41 [ 0.776018] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.781761] iommu: Adding device 7d008000.usb to group 43 [ 0.787117] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.792848] iommu: Adding device pmu to group 45 [ 0.797425] iommu: Adding device timer to group 46 [ 0.802192] iommu: Adding device clocks to group 47 [ 0.807061] iommu: Adding device gpio-keys to group 48 [ 0.812160] iommu: Adding device regulators to group 49 [ 0.817384] iommu: Adding device regulators:regulator@0 to group 50 [ 0.823598] iommu: Adding device regulators:regulator@1 to group 51 [ 0.829858] iommu: Adding device regulators:regulator@2 to group 52 [ 0.836079] iommu: Adding device regulators:regulator@3 to group 53 [ 0.842335] iommu: Adding device regulators:regulator@4 to group 54 [ 0.848564] iommu: Adding device regulators:regulator@7 to group 55 [ 0.854816] iommu: Adding device regulators:regulator@8 to group 56 [ 0.861045] iommu: Adding device regulators:regulator@10 to group 57 [ 0.867382] iommu: Adding device regulators:regulator@11 to group 58 [ 0.873691] iommu: Adding device regulators:regulator@12 to group 59 [ 0.880036] iommu: Adding device regulators:regulator@13 to group 60 [ 0.886345] iommu: Adding device regulators:regulator@14 to group 61 [ 0.892687] iommu: Adding device sound to group 62 [ 0.914310] +5V_SYS: supplied by +VDD_MUX [ 0.916802] +3.3V_SYS: supplied by +VDD_MUX [ 0.921367] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.926681] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.934807] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.940528] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.948767] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.955546] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.963749] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.969561] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.977789] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.983339] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.991567] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.997205] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 1.006642] vgaarb: loaded [ 1.008801] SCSI subsystem initialized [ 1.011982] libata version 3.00 loaded. [ 1.015876] usbcore: registered new interface driver usbfs [ 1.021103] usbcore: registered new interface driver hub [ 1.026411] usbcore: registered new device driver usb [ 1.034636] Linux video capture interface: v2.00 [ 1.037417] pps_core: LinuxPPS API ver. 1 registered [ 1.042316] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.051422] PTP clock support registered [ 1.056724] Advanced Linux Sound Architecture Driver Initialized. [ 1.061996] Bluetooth: Core ver 2.22 [ 1.064953] NET: Registered protocol family 31 [ 1.069351] Bluetooth: HCI device and connection manager initialized [ 1.075654] Bluetooth: HCI socket layer initialized [ 1.080527] Bluetooth: L2CAP socket layer initialized [ 1.085561] Bluetooth: SCO socket layer initialized [ 1.091041] clocksource: Switched to clocksource arch_sys_counter [ 1.186787] NET: Registered protocol family 2 [ 1.190234] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.196378] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.202864] TCP: Hash tables configured (established 8192 bind 8192) [ 1.209481] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.214948] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.221546] NET: Registered protocol family 1 [ 1.226268] RPC: Registered named UNIX socket transport module. [ 1.231467] RPC: Registered udp transport module. [ 1.236121] RPC: Registered tcp transport module. [ 1.240801] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.247685] iommu: Adding device regulatory.0 to group 63 [ 1.252816] PCI: CLS 0 bytes, default 64 [ 1.258303] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 1.265376] iommu: Adding device alarmtimer to group 64 [ 1.270983] Initialise system trusted keyrings [ 1.274464] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 1.282097] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.287237] NFS: Registering the id_resolver key type [ 1.291547] Key type id_resolver registered [ 1.295662] Key type id_legacy registered [ 1.304582] Key type asymmetric registered [ 1.306769] Asymmetric key parser 'x509' registered [ 1.311776] bounce: pool size: 64 pages [ 1.315503] io scheduler noop registered (default) [ 1.320203] io scheduler mq-deadline registered [ 1.324753] io scheduler kyber registered [ 1.330534] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.335525] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 1.342517] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 1.358627] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 1.362390] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 1.372231] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 1.382958] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.389913] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 1.395481] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.401343] iommu: Adding device serial8250 to group 65 [ 1.408213] console [ttyS0] disabled [ 1.409975] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.418946] console [ttyS0] enabled [ 1.418946] console [ttyS0] enabled [ 1.425152] bootconsole [earlycon0] disabled [ 1.425152] bootconsole [earlycon0] disabled [ 1.434866] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.445562] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.474016] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.493663] loop: module loaded [ 1.498158] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.505621] as3722 4-0040: AS3722 with revision 0x1 found [ 1.513279] iommu: Adding device as3722-pinctrl to group 66 [ 1.520575] iommu: Adding device as3722-regulator to group 67 [ 1.529345] as3722-sd2: supplied by +5V_SYS [ 1.534055] as3722-sd3: supplied by +5V_SYS [ 1.538483] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.544871] as3722-sd4: supplied by +5V_SYS [ 1.549530] as3722-sd5: supplied by +5V_SYS [ 1.555657] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.561796] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.568036] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.573997] as3722-ldo3: supplied by +3.3V_SYS [ 1.578490] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.586328] as3722-ldo4: supplied by +3.3V_SYS [ 1.591003] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.597277] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.602151] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.609097] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.614772] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.620949] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.631273] iommu: Adding device as3722-rtc to group 68 [ 1.636651] iommu: Adding device as3722-adc to group 69 [ 1.642049] iommu: Adding device as3722-power-off to group 70 [ 1.647939] iommu: Adding device as3722-wdt to group 71 [ 1.653968] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.672608] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.679332] iommu: Adding device Fixed MDIO bus.0 to group 72 [ 1.685284] libphy: Fixed MDIO Bus: probed [ 1.689376] CAN device driver interface [ 1.693313] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.700263] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.705996] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.713494] usbcore: registered new interface driver pegasus [ 1.719213] usbcore: registered new interface driver asix [ 1.724704] usbcore: registered new interface driver ax88179_178a [ 1.730840] usbcore: registered new interface driver cdc_ether [ 1.736790] usbcore: registered new interface driver smsc75xx [ 1.742620] usbcore: registered new interface driver smsc95xx [ 1.748409] usbcore: registered new interface driver net1080 [ 1.754164] usbcore: registered new interface driver cdc_subset [ 1.760125] usbcore: registered new interface driver zaurus [ 1.765806] usbcore: registered new interface driver cdc_ncm [ 1.771752] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.777376] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.783098] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.789617] ehci-pci: EHCI PCI platform driver [ 1.794140] tegra-ehci: Tegra EHCI driver [ 1.800989] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.806427] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.814241] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 1.841073] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.847905] hub 1-0:1.0: USB hub found [ 1.851718] hub 1-0:1.0: 1 port detected [ 1.856895] usbcore: registered new interface driver cdc_acm [ 1.862568] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.870625] usbcore: registered new interface driver cdc_wdm [ 1.876382] usbcore: registered new interface driver usb-storage [ 1.884035] iommu: Adding device ci_hdrc.0 to group 73 [ 1.895973] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.902872] as3722-rtc as3722-rtc: RTC interrupt 379 [ 1.910703] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.917905] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.924451] i2c /dev entries driver [ 1.929200] usbcore: registered new interface driver uvcvideo [ 1.934962] USB Video Class driver (1.1.1) [ 1.939051] gspca_main: v2.14.0 registered [ 1.943799] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.954080] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) [ 1.962581] iommu: Adding device cpufreq-tegra124 to group 74 [ 1.968889] sdhci: Secure Digital Host Controller Interface driver [ 1.975082] sdhci: Copyright(c) Pierre Ossman [ 1.979432] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.985425] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.990315] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.011096] mmc0: Unknown controller version (3). You may experience problems. [ 2.018354] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.081111] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.092603] usbcore: registered new interface driver usbhid [ 2.098278] usbhid: USB HID core driver [ 2.105171] iommu: Adding device snd-soc-dummy to group 75 [ 2.157506] mmc0: new high speed MMC card at address 0001 [ 2.163514] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.168439] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.174818] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.180922] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (247:0) [ 2.189965] mmcblk0: p1 [ 2.551524] iommu: Adding device 70301100.i2s to group 76 [ 2.557785] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub [ 2.578135] tegra-snd-rt5640 sound: rt5640-aif1 <-> 70301100.i2s mapping ok [ 2.588912] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input0 [ 2.600117] NET: Registered protocol family 10 [ 2.605927] Segment Routing with IPv6 [ 2.609761] mip6: Mobile IPv6 [ 2.612752] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.620163] NET: Registered protocol family 17 [ 2.624682] NET: Registered protocol family 15 [ 2.629133] can: controller area network core (rev 20170425 abi 9) [ 2.635540] NET: Registered protocol family 29 [ 2.639979] can: raw protocol (rev 20170425) [ 2.644261] can: broadcast manager protocol (rev 20170425 t) [ 2.649920] can: netlink gateway (rev 20170425) max_hops=1 [ 2.655651] Bluetooth: RFCOMM socket layer initialized [ 2.660800] Bluetooth: RFCOMM ver 1.11 [ 2.664585] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.669896] Bluetooth: BNEP socket layer initialized [ 2.674871] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.680788] Bluetooth: HIDP socket layer initialized [ 2.686013] Key type dns_resolver registered [ 2.690786] Registering SWP/SWPB emulation handler [ 2.696398] Loading compiled-in X.509 certificates [ 2.718864] +3.3V_RUN: supplied by +3.3V_SYS [ 2.724012] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.728714] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.734748] +5V_USB_HS: supplied by +5V_SYS [ 2.739843] +3.3V_LP0: supplied by +3.3V_SYS [ 2.745195] +5V_HDMI_CON: supplied by +5V_SYS [ 2.749973] +5V_SATA: supplied by +5V_SYS [ 2.754651] +12V_SATA: supplied by +VDD_MUX [ 2.760285] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.767161] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.774353] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.781881] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.787495] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.796608] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.805653] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.814217] as3722-sd2: supplied by +5V_SYS [ 2.818707] as3722-sd3: supplied by +5V_SYS [ 2.823233] as3722-sd4: supplied by +5V_SYS [ 2.827722] as3722-sd5: supplied by +5V_SYS [ 2.833665] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.839142] as3722-ldo1: supplied by +3.3V_RUN [ 2.844338] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.849881] as3722-ldo3: supplied by +3.3V_SYS [ 2.855423] as3722-ldo4: supplied by +3.3V_SYS [ 2.860174] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.865993] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 [ 2.874636] as3722-ldo6: supplied by +3.3V_RUN [ 2.879630] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.885098] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.892221] as3722-ldo9: supplied by +5V_SYS [ 2.897692] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.904454] as3722-ldo10: supplied by +5V_SYS [ 2.909558] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.916429] as3722-ldo11: supplied by +3.3V_RUN [ 2.921457] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.930692] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.939769] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.950320] scsi host0: tegra-ahci [ 2.954790] scsi host1: tegra-ahci [ 2.958496] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.966543] ata2: DUMMY [ 2.970154] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.975636] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.983486] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 3.011173] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 3.018296] hub 2-0:1.0: USB hub found [ 3.022177] hub 2-0:1.0: 1 port detected [ 3.039099] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 [ 3.048907] tegra-xusb 70090000.usb: failed to request firmware: -2 [ 3.055222] tegra-xusb 70090000.usb: failed to load firmware: -2 [ 3.061950] tegra-xusb: probe of 70090000.usb failed with error -2 [ 3.068975] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 3.073922] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 3.085322] mmc1: Unknown controller version (3). You may experience problems. [ 3.092663] mmc1: Invalid maximum block size, assuming 512 bytes [ 3.161683] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 3.169367] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 3.180290] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 3.188637] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 3.211950] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 3.220250] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 3.234298] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.240580] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.246816] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.253802] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.261256] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.266883] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 3.272960] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.282670] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.292462] pci 0000:00:01.0: enabling Extended Tags [ 3.294551] ata1: SATA link down (SStatus 0 SControl 300) [ 3.303080] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.312859] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.322647] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.329259] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.339409] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.345482] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.355148] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.364838] pci 0000:00:02.0: enabling Extended Tags [ 3.369801] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.379609] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.389448] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.396118] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.406132] PCI: bus0: Fast back to back transfers disabled [ 3.411725] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.419728] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.428008] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.434136] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.441267] PCI: bus1: Fast back to back transfers disabled [ 3.446916] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.453807] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.459905] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.465579] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.472464] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.479941] PCI: bus2: Fast back to back transfers disabled [ 3.485593] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.492323] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.499176] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.506174] mmc1: new high speed SDHC card at address aaaa [ 3.512266] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.517342] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.525192] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.531593] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.538990] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.544169] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.551091] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.559005] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.566439] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.572742] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.577773] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.584155] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.591008] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.599059] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.606401] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.613114] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.619330] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.626649] mmcblk1: p1 p2 p3 [ 3.629969] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.636884] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.643707] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.649323] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.655257] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.692903] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0x4a38b41c, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.702510] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.714660] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.724072] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.730699] [drm] No driver support for vblank timestamp query. [ 3.865043] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 4.112237] Console: switching to colour frame buffer device 512x135 [ 4.208136] drm drm: fb0: frame buffer device [ 4.212681] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 4.219932] iommu: Adding device cpufreq-dt.0 to group 77 [ 4.225678] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 4.233023] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 4.242062] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [ 4.249142] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:14 UTC (946684814) [ 4.257980] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.267633] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.274284] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.281679] +USB0_VBUS_SW: disabling [ 4.281694] +1.8V_RUN_CAM: disabling [ 4.282984] +2.8V_RUN_CAM: disabling [ 4.286689] +1.2V_RUN_CAM_FRONT: disabling [ 4.290225] +1.05V_RUN_CAM_REAR: disabling [ 4.293824] +3.3V_RUN_TOUCH: disabling [ 4.297935] +2.8V_RUN_CAM_AF: disabling [ 4.302055] +1.8V_RUN_VPP_FUSE: disabling [ 4.305814] ALSA device list: [ 4.305817] #0: tegra-hda at 0x70038000 irq 346 [ 4.305819] #1: NVIDIA Tegra Jetson TK1 [ 4.325323] cfg80211: failed to load regulatory.db [ 4.330808] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.385841] EXT4-fs (mmcblk0p1): recovery complete [ 4.392000] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.400206] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.411100] devtmpfs: mounted [ 4.414597] Freeing unused kernel memory: 1024K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#