Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.34 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.94 sec Percent passed so far: 100.0 Final Score: 100.0 ¨[0025.446] Enabled early print [0025.449] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0025.455] Processing in recovery mode [0025.458] A02 Bootrom Patch rev = 63 [0025.461] Power-up reason: pmc por [0025.465] Established communication link with host [0026.432] Odmdata from BCT: 0x00084000 [0026.436] DebugPort= 0x3 [0026.438] BoardId read from EEPROM/NCT: 2180 [0026.466] Turned on fan for loki board [0026.470] Key release before reqd. time for fastboot [0026.475] No Battery Present [0026.477] RamCode = 0 [0026.480] Platform has Ddr4 type ram [0026.483] max77620 disabling SD1 Remote Sense [0026.487] Setting Ddr voltage to 1125mv [0026.491] Serial Number of Pmic Max77663: 0x102f6 [0026.499] Entering ramdump check [0026.502] Get RamDumpCarveOut = 0x0 [0026.505] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0026.510] Last reboot was clean, booting normally! [0026.515] Sdram initialization is successful [0026.519] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0026.525] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0026.530] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0026.535] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0026.540] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0026.545] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0026.550] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0026.556] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0026.571] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0026.577] Platform-DebugCarveout: 0 [0026.580] Downloaded Bct successfully [0026.685] Downloaded bootloader successfully at 0x92c00000 [0026.801] Downloaded rp1 successfully at 0x83000000 [0026.849] MAX77620_GPIO1 Configured. [0026.852] MAX77620_GPIO5 Configured. [0026.856] CPU power rail is up [0026.858] CPU clock enabled [0026.862] Performing RAM repair [0026.865] Updating A64 Warmreset Address to 0x92c002e9 [0026.871] Enable APE clock/reset [0026.874] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0026.879] Loading Secure OS image failed. [0026.883] Set NvDecSticky Bits [0026.886] GSC1 address : ff700000 [0026.890] GSC2 address ff63fffc value c0edbbcc [0026.895] GSC2 address : ff600000 [0026.898] GSC3 address : ff500000 [0026.902] GSC4 address : ff400000 [0026.906] GSC5 address : ff300000 [0026.909] GSC MC Settings done [0026.912] NvTbootPackSdramParams: start. [0026.917] NvTbootPackSdramParams: done. [0026.921] Next binary entry address: 0x92c00258 [0026.925] BoardId: 2180 [0026.928] dram memory type is 3 [0026.931] Tegraboot started after 26057517 us [0026.935] Basic modules init took -26057517 us [0026.940] USB data transfer took 0 us [0026.943] Carveout took 27574385 us [0026.947] CPU initialization took 3629 us [0026.950] Total time taken by TegraBoot 1520497 us [0026.955] Starting CPU & Halting co-processor [0027.611] [0027.612] Debug Init done [0027.615] Marked DTB cacheable [0027.618] Bootloader DTB loaded at 0x83000000 [0027.622] DeviceTree Init done [0027.636] Pinmux applied successfully [0027.641] gicd_base: 0x50041000 [0027.645] gicc_base: 0x50042000 [0027.648] Interrupts Init done [0027.653] Using base:0x60005008 & irq:33 for tick-timer [0027.658] Using base:0x60005000 for delay-timer [0027.662] platform_init_timer: DONE [0027.666] Timer(tick) Init done [0027.670] osc freq = 38400 khz [0027.675] [0027.676] welcome to cboot [0027.678] [0027.679] Cboot Version: 24.00.2015.42-t210-63d15635 [0027.684] calling constructors [0027.687] initializing heap [0027.690] initializing threads [0027.693] initializing timers [0027.696] creating bootstrap completion thread [0027.700] top of bootstrap2() [0027.703] CPU: ARM Cortex A57 [0027.706] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0027.711] initializing platform [0027.737] config for ddr50 mode completed [0027.741] sdmmc bdev is already initialized [0027.745] of_register: registering tegra_udc to of_hal [0027.750] of_register: registering inv20628-driver to of_hal [0027.756] of_register: registering ads1015-driver to of_hal [0027.761] of_register: registering lp8557-bl-driver to of_hal [0027.767] of_register: registering bq2419x_charger to of_hal [0027.773] of_register: registering cpc to of_hal [0027.777] of_register: registering bq27441_fuel_gauge to of_hal [0027.792] gpio framework initialized [0027.795] of_register: registering tca9539_gpio to of_hal [0027.800] of_register: registering tca9539_gpio to of_hal [0027.806] of_register: registering i2c_bus_driver to of_hal [0027.811] of_register: registering i2c_bus_driver to of_hal [0027.817] of_register: registering i2c_bus_driver to of_hal [0027.822] pmic framework initialized [0027.826] of_register: registering max77620_pmic to of_hal [0027.831] regulator framework initialized [0027.835] of_register: registering tps65132_bl_driver to of_hal [0027.841] of_register: registering tegra_xhci to of_hal [0027.846] initializing target [0027.853] gpio_driver_register: register 'tegra_gpio_driver' driver [0027.863] fixed regulator driver initialized [0027.927] initializing OF layer [0027.932] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0027.940] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0027.962] I2C Bus Init done [0027.964] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0027.976] I2C Bus Init done [0027.979] of_children_init: Ops found for compatible string ti,lp8557 [0027.985] I2C slave not started [0027.988] I2C write failed [0027.991] Writing offset failed [0027.994] failed to read 0x 0 [0027.997] lp8557: Couldn't turn off backlight: -3 [0028.002] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0028.016] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0028.021] gpio_driver_register: register 'tca9539_gpio_driver' driver [0028.027] of_children_init: Ops found for compatible string ti,tca9539 [0028.039] tca9539_init: i2c bus: 2, slave addr: 0xee [0028.044] gpio_driver_register: register 'tca9539_gpio_driver' driver [0028.051] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.063] I2C Bus Init done [0028.065] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.077] I2C Bus Init done [0028.080] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.092] I2C Bus Init done [0028.095] of_children_init: Ops found for compatible string maxim,max77620 [0028.107] max77620_init using irq 118 [0028.112] register 'maxim,max77620' pmic [0028.116] gpio_driver_register: register 'max77620-gpio' driver [0028.122] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.135] I2C Bus Init done [0028.137] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0028.146] calling apps_init() [0028.151] Found 19 GPT partitions in "sdmmc3_user" [0028.156] Proceeding to flashing Server [0028.160] usbdcd_reinit Initialize driver to use already enumerated device [0028.167] nv3p_priv_usbf_open USB configuration success [0028.176] Writing GPT partition [0028.181] Erasing Boot device [0028.207] Erasing Storage Device [0028.476] Sanitizing Storage Device [0028.615] Writing protective mbr [0028.619] Writing primary GPT [0028.624] Writing secondary GPT [0028.630] Found 18 GPT partitions in "sdmmc3_user" [0028.637] Writing NVC partition [0028.640] bct_init bctinit [0028.642] bct_init bctinit [0028.653] bct_init bctinit [0028.656] bct_init bctinit [0028.658] bct_init bctinit [0028.695] partition NVC write successful. [0028.701] Writing APP partition [0028.704] bct_init bctinit [0029.737] bct_init bctinit [0029.740] bct_init bctinit [0030.337] partition APP write successful. [0030.344] Writing TBC partition [0030.347] bct_init bctinit [0030.354] bct_init bctinit [0030.356] bct_init bctinit [0030.362] partition TBC write successful. [0030.368] Writing EBT partition [0030.371] bct_init bctinit [0030.396] bct_init bctinit [0030.398] bct_init bctinit [0030.410] partition EBT write successful. [0030.416] Writing BPF partition [0030.419] bct_init bctinit [0030.425] bct_init bctinit [0030.428] bct_init bctinit [0030.435] partition BPF write successful. [0030.441] Writing WB0 partition [0030.444] bct_init bctinit [0030.448] bct_init bctinit [0030.451] bct_init bctinit [0030.455] partition WB0 write successful. [0030.461] Writing RP1 partition [0030.464] bct_init bctinit [0030.485] bct_init bctinit [0030.487] bct_init bctinit [0030.497] partition RP1 write successful. [0030.503] Writing TOS partition [0030.506] bct_init bctinit [0030.513] bct_init bctinit [0030.516] bct_init bctinit [0030.524] partition TOS write successful. [0030.530] Writing DTB partition [0030.533] bct_init bctinit [0030.554] bct_init bctinit [0030.557] bct_init bctinit [0030.567] partition DTB write successful. [0030.578] Writing BCT partition [0030.583] bct_init bctinit [0030.678] partition BCT write successful. [0030.690] Change state to cold boot mode [0030.693] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.179] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0x102f6 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.318] Loading Tboot-CPU binary [0000.367] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.393] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.678] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132253 us [0000.779] Basic modules init took 292351 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12211 us [0000.800] Carveout took 264395 us [0000.803] CPU initialization took 92751 us [0000.807] Total time taken by TegraBoot 661708 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.964] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 è¬[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x102f6 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99175 us [0000.746] Basic modules init took 292164 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12211 us [0000.768] Carveout took 264391 us [0000.771] CPU initialization took 92754 us [0000.775] Total time taken by TegraBoot 661520 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 74 ms (4.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6914801 bytes read in 212 ms (31.1 MiB/s) Retrieving file: /boot/Image 16710144 bytes read in 423 ms (37.7 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2390/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 53 ms (967.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.466524] console [ttyS0] enabled [ 0.466524] console [ttyS0] enabled [ 0.474181] bootconsole [uart0] disabled [ 0.474181] bootconsole [uart0] disabled [ 0.482874] SuperH (H)SCI(F) driver initialized [ 0.488063] msm_serial: driver initialized [ 0.492916] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.503510] loop: module loaded [ 0.508696] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.520380] max77620-sd0: supplied by regulator-dummy [ 0.526916] max77620-sd1: supplied by regulator-dummy [ 0.533065] max77620-sd2: supplied by regulator-dummy [ 0.539004] max77620-sd3: supplied by regulator-dummy [ 0.545418] max77620-ldo0: supplied by regulator-dummy [ 0.551502] max77620-ldo1: supplied by regulator-dummy [ 0.557272] max77620-ldo2: supplied by regulator-dummy [ 0.563312] max77620-ldo3: supplied by regulator-dummy [ 0.568487] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.575399] max77620-ldo4: supplied by regulator-dummy [ 0.580575] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.587165] max77620-ldo5: supplied by regulator-dummy [ 0.592345] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.599350] max77620-ldo6: supplied by regulator-dummy [ 0.604520] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.611440] max77620-ldo7: supplied by regulator-dummy [ 0.617441] max77620-ldo8: supplied by regulator-dummy [ 0.631348] libphy: Fixed MDIO Bus: probed [ 0.636231] tun: Universal TUN/TAP device driver, 1.6 [ 0.642856] thunder-xcv, ver 1.0 [ 0.646441] thunder-BGX, ver 1.0 [ 0.649834] thunder-nic, ver 1.0 [ 0.653429] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.659440] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.665441] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.672462] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.678093] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.685955] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.692234] sky2: driver version 1.30 [ 0.696439] usbcore: registered new interface driver r8152 [ 0.702231] VFIO - User Level meta-driver version: 0.3 [ 0.712473] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.719385] ehci-pci: EHCI PCI platform driver [ 0.723890] ehci-platform: EHCI generic platform driver [ 0.729277] ehci-orion: EHCI orion driver [ 0.733469] ehci-exynos: EHCI EXYNOS driver [ 0.737790] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.744012] ohci-pci: OHCI PCI platform driver [ 0.748516] ohci-platform: OHCI generic platform driver [ 0.753885] ohci-exynos: OHCI EXYNOS driver [ 0.758917] usbcore: registered new interface driver usb-storage [ 0.899232] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.907756] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.915166] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.921559] i2c /dev entries driver [ 0.929486] sdhci: Secure Digital Host Controller Interface driver [ 0.936677] sdhci: Copyright(c) Pierre Ossman [ 0.941354] Synopsys Designware Multimedia Card Interface Driver [ 0.948377] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.954550] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.973644] mmc0: Unknown controller version (3). You may experience problems. [ 1.025615] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.037908] ledtrig-cpu: registered to indicate activity on CPUs [ 1.045847] usbcore: registered new interface driver usbhid [ 1.052275] usbhid: USB HID core driver [ 1.061790] NET: Registered protocol family 17 [ 1.066876] 9pnet: Installing 9P2000 support [ 1.071223] Key type dns_resolver registered [ 1.076044] registered taskstats version 1 [ 1.080369] Loading compiled-in X.509 certificates [ 1.092272] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.097267] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.103185] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.108596] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.114757] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.120391] mmc0: new high speed MMC card at address 0001 [ 1.126253] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.130961] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.137020] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.142986] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.147931] RTL_5V: supplied by VDD_5V0_SYS [ 1.148157] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.157758] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.165616] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.170760] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.183136] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.192182] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.192406] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.192468] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.192518] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.220746] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.230466] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.238679] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.647101] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.056089] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.465082] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.472572] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.478062] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.486253] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.895215] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.304197] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.713176] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.720665] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.726274] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.732581] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.738769] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.745649] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.752968] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.758872] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.766949] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.776308] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.846253] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.853657] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.859066] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.867642] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.876275] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.882761] hub 1-0:1.0: USB hub found [ 3.886623] hub 1-0:1.0: 5 ports detected [ 3.891015] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.896495] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.904149] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.912602] hub 2-0:1.0: USB hub found [ 3.916443] hub 2-0:1.0: 4 ports detected [ 3.921776] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.933745] mmc1: Unknown controller version (3). You may experience problems. [ 3.985676] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.993908] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.006109] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.013776] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.022415] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.034859] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.066608] max77686-rtc max77620-rtc: setting system clock to 2017-05-13 15:11:41 UTC (1494688301) [ 4.254112] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.280891] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.293774] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.418499] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.478824] r8152 2-1:1.0 eth0: v1.09.9 [ 4.482902] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.495026] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.744193] r8152 2-1:1.0 eth0: carrier on [ 8.773610] IP-Config: Complete: [ 8.776854] device=eth0, hwaddr=00:04:4b:5a:c3:ba, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.787017] host=192.168.99.2, domain=, nis-domain=(none) [ 8.792843] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.800267] AVDD_DSI_CSI_1V2: disabling [ 8.804122] VDD_PRE_REG_1V35: disabling [ 8.807995] VDD_CAM_HV: disabling [ 8.811453] VDD_TS_HV: disabling [ 8.814800] VDD_TS_1V8: disabling [ 8.818113] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.822466] VDD_3V3_SD: disabling [ 8.825781] VDD_HDMI_5V0: disabling [ 8.829259] ALSA device list: [ 8.832224] No soundcards found. [ 8.836297] Freeing unused kernel memory: 1088K /init: line 58: chmod: command not found [ 15:11:46 ] L4T-INITRD Build DATE: Sat May 13 15:11:46 UTC 2017 [ 15:11:46 ] Root device found: nfs [ 15:11:46 ] Ethernet interfaces: eth0 [ 15:11:46 ] IP Address: 192.168.99.2 [ 15:11:46 ] Rootfs mounted over nfs [ 15:11:46 ] Switching from initrd to actual rootfs [ 9.498289] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.516651] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.578028] systemd[1]: Set hostname to . [ 10.027262] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 10.045942] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 10.065721] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.081781] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 10.101734] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 10.117819] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 10.133732] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Syslog Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Swap. [ OK ] Listening on Journal Socket. [ OK ] Created slice System Slice. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... Starting Journal Service... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Debug File System... [ OK ] Reached target Slices. Starting Create Static Device Nodes in /dev... Mounting RPC Pipe File System... Mounting Huge Pages File System... [ OK ] Created slice system-getty.slice. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Journal Service. Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Mounting Configuration File System... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Mounted Configuration File System. [ 10.732603] systemd-journald[1505]: Received request to flush runtime journal from PID 1 Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... [ OK ] Started Flush Journal to Persistent Storage. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started udev Kernel Device Manager. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting Permit User Sessions... Starting LSB: Start NTP daemon... Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started D-Bus System Message Bus. Starting /etc/rc.local Compatibility... Starting System Logging Service... Starting OpenBSD Secure Shell server... [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Found device /dev/ttyS0. [ 12.374124] random: crng init done [ OK ] Started System Logging Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started LSB: Start NTP daemon. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started Login Service. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: áé[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x102f6 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99174 us [0000.746] Basic modules init took 292158 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12211 us [0000.768] Carveout took 264391 us [0000.771] CPU initialization took 92753 us [0000.775] Total time taken by TegraBoot 661513 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 74 ms (4.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6914801 bytes read in 212 ms (31.1 MiB/s) Retrieving file: /boot/Image 16710144 bytes read in 423 ms (37.7 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2390/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 53 ms (967.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.466447] console [ttyS0] enabled [ 0.466447] console [ttyS0] enabled [ 0.474100] bootconsole [uart0] disabled [ 0.474100] bootconsole [uart0] disabled [ 0.482798] SuperH (H)SCI(F) driver initialized [ 0.487979] msm_serial: driver initialized [ 0.492825] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.503418] loop: module loaded [ 0.508612] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.520333] max77620-sd0: supplied by regulator-dummy [ 0.526823] max77620-sd1: supplied by regulator-dummy [ 0.533010] max77620-sd2: supplied by regulator-dummy [ 0.538937] max77620-sd3: supplied by regulator-dummy [ 0.545349] max77620-ldo0: supplied by regulator-dummy [ 0.551438] max77620-ldo1: supplied by regulator-dummy [ 0.557208] max77620-ldo2: supplied by regulator-dummy [ 0.563251] max77620-ldo3: supplied by regulator-dummy [ 0.568429] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.575344] max77620-ldo4: supplied by regulator-dummy [ 0.580517] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.587106] max77620-ldo5: supplied by regulator-dummy [ 0.592288] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.599295] max77620-ldo6: supplied by regulator-dummy [ 0.604465] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.611384] max77620-ldo7: supplied by regulator-dummy [ 0.617382] max77620-ldo8: supplied by regulator-dummy [ 0.631253] libphy: Fixed MDIO Bus: probed [ 0.636143] tun: Universal TUN/TAP device driver, 1.6 [ 0.642772] thunder-xcv, ver 1.0 [ 0.646303] thunder-BGX, ver 1.0 [ 0.649732] thunder-nic, ver 1.0 [ 0.653322] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.659329] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.665330] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.672349] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.677980] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.685843] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.692121] sky2: driver version 1.30 [ 0.696323] usbcore: registered new interface driver r8152 [ 0.702113] VFIO - User Level meta-driver version: 0.3 [ 0.712368] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.719278] ehci-pci: EHCI PCI platform driver [ 0.723782] ehci-platform: EHCI generic platform driver [ 0.729164] ehci-orion: EHCI orion driver [ 0.733354] ehci-exynos: EHCI EXYNOS driver [ 0.737676] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.743900] ohci-pci: OHCI PCI platform driver [ 0.748404] ohci-platform: OHCI generic platform driver [ 0.753772] ohci-exynos: OHCI EXYNOS driver [ 0.758802] usbcore: registered new interface driver usb-storage [ 0.899066] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.907581] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.914990] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.921382] i2c /dev entries driver [ 0.930313] sdhci: Secure Digital Host Controller Interface driver [ 0.936616] sdhci: Copyright(c) Pierre Ossman [ 0.941319] Synopsys Designware Multimedia Card Interface Driver [ 0.948208] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.954407] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.973477] mmc0: Unknown controller version (3). You may experience problems. [ 1.025446] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.037737] ledtrig-cpu: registered to indicate activity on CPUs [ 1.045675] usbcore: registered new interface driver usbhid [ 1.052185] usbhid: USB HID core driver [ 1.061610] NET: Registered protocol family 17 [ 1.066705] 9pnet: Installing 9P2000 support [ 1.071053] Key type dns_resolver registered [ 1.075875] registered taskstats version 1 [ 1.080203] Loading compiled-in X.509 certificates [ 1.092072] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.097068] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.102983] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.108393] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.114557] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.120191] mmc0: new high speed MMC card at address 0001 [ 1.126061] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.130771] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.136830] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.142794] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.147741] RTL_5V: supplied by VDD_5V0_SYS [ 1.147975] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.157570] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.165381] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.170570] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.182945] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.192015] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.192227] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.192294] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.192347] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.220608] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.230365] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.238580] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.646963] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.055958] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.464956] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.472448] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.477938] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.486129] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.895123] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.304113] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.713114] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.720604] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.726209] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.732516] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.738705] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.745586] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.752905] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.758811] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.766921] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.776277] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.846087] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.853491] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.858898] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.867477] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.876111] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.882594] hub 1-0:1.0: USB hub found [ 3.886459] hub 1-0:1.0: 5 ports detected [ 3.890859] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.896337] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.903990] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.912445] hub 2-0:1.0: USB hub found [ 3.916288] hub 2-0:1.0: 4 ports detected [ 3.921622] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.933577] mmc1: Unknown controller version (3). You may experience problems. [ 3.985511] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.993741] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.005932] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.013604] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.022251] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.034689] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.066443] max77686-rtc max77620-rtc: setting system clock to 2017-05-13 15:12:43 UTC (1494688363) [ 4.253945] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.280723] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.293604] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.418336] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.478655] r8152 2-1:1.0 eth0: v1.09.9 [ 4.482731] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.494847] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.808013] r8152 2-1:1.0 eth0: carrier on [ 8.833445] IP-Config: Complete: [ 8.836668] device=eth0, hwaddr=00:04:4b:5a:c3:ba, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.846861] host=192.168.99.2, domain=, nis-domain=(none) [ 8.852691] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.860119] AVDD_DSI_CSI_1V2: disabling [ 8.863971] VDD_PRE_REG_1V35: disabling [ 8.867820] VDD_CAM_HV: disabling [ 8.871302] VDD_TS_HV: disabling [ 8.874650] VDD_TS_1V8: disabling [ 8.877964] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.882318] VDD_3V3_SD: disabling [ 8.885633] VDD_HDMI_5V0: disabling [ 8.889111] ALSA device list: [ 8.892076] No soundcards found. [ 8.896150] Freeing unused kernel memory: 1088K /init: line 58: chmod: command not found [ 15:12:48 ] L4T-INITRD Build DATE: Sat May 13 15:12:48 UTC 2017 [ 15:12:48 ] Root device found: nfs [ 15:12:48 ] Ethernet interfaces: eth0 [ 15:12:48 ] IP Address: 192.168.99.2 [ 15:12:48 ] Rootfs mounted over nfs [ 15:12:48 ] Switching from initrd to actual rootfs [ 9.151325] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.169766] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.186338] systemd[1]: Set hostname to . [ 9.495917] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 9.513647] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 9.533581] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 9.553545] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 9.569759] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 9.585633] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.602741] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... Mounting Debug File System... Mounting POSIX Message Queue File System... Starting Remount Root and Kernel File Systems... Starting Load Kernel Modules... [ OK ] Listening on Syslog Socket. Mounting RPC Pipe File System... [ OK ] Reached target Swap. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Journal Audit Socket. [ OK ] Created slice system-getty.slice. [ OK ] Listening on udev Control Socket. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Reached target Encrypted Volumes. Starting Journal Service... Starting Create Static Device Nodes in /dev... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Journal Service. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Mounted Configuration File System. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Apply Kernel Variables. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Load/Save Random Seed. [ 10.314710] systemd-journald[1512]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting System Logging Service... Starting LSB: Start NTP daemon... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [ OK ] Started D-Bus System Message Bus. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting /etc/rc.local Compatibility... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Login Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Getty on tty1. [ OK ] Found device /dev/ttyS0. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ 12.398202] random: crng init done Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ø