[0000.741] [TegraBoot] (version 23.00.2015.14-mobile-1ef66670) [0000.747] Processing in cold boot mode Bootloader 2 [0000.751] A01Q Bootrom Patch rev = 3 [0000.755] Power-up reason: pmu watchdog [0000.758] No Battery Present [0000.761] Platform has Ddr4 type ram [0000.765] max77620 disabling SD1 Remote Sense [0000.769] Setting Ddr voltage to 1125mv [0000.773] Serial Number of Pmic Max77663: 0x40daf [0000.781] Entering ramdump check [0000.784] Get RamDumpCarveOut = 0x0 [0000.787] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.792] Last reboot was clean, booting normally! [0000.797] Sdram initialization is successful [0000.801] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.806] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.832] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.858] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.863] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.868] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.873] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.879] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.894] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.900] Platform-DebugCarveout: 0 [0000.903] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.952] Using GPT Primary to query partitions [0000.958] Loading Tboot-CPU binary [0001.007] Verifying bootloader in OdmNonSecureSBK mode [0001.016] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.026] Bootloader downloaded successfully. [0001.030] Downloaded Tboot-CPU binary to 0xa0000258 [0001.035] MAX77620_GPIO1 Configured. [0001.039] MAX77620_GPIO5 Configured. [0001.042] CPU power rail is up [0001.045] CPU clock enabled [0001.049] Performing RAM repair [0001.052] Updating A64 Warmreset Address to 0xa00002e9 [0001.071] Bootloader DTB Load Address: 0x83000000 [0001.088] Kernel DTB Load Address: 0x83080000 [0001.093] Loading cboot binary [0001.187] Verifying bootloader in OdmNonSecureSBK mode [0001.275] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0001.284] Bootloader downloaded successfully. [0001.288] GPT: Partition NOT found ! [0001.292] Find Partition via GPT Failed [0001.295] function NvTbootGetBinaryOffsets: 0x845208 error [0001.301] Error in NvTbootLoadBinary: 0x845208 ! [0001.305] GPT: Partition NOT found ! [0001.309] No FB partition [0001.311] Next binary entry address: 0x80110000 [0001.315] BoardId: 2595 [0001.320] dram memory type is 3 [0001.326] WB0 init successful [0001.353] Bpmp FW successfully loaded [0001.356] Set NvDecSticky Bits [0001.359] GSC1 address : ff700000 [0001.363] GSC2 address : ff600000 [0001.367] GSC3 address : ff500000 [0001.371] GSC4 address : ff400000 [0001.374] GSC5 address : ff300000 [0001.378] GSC MC Settings done [0001.383] TOS old plaintext Image length 61440 [0001.389] *** Secure OS image signature not verified *** [0001.394] Loading and Validation of Secure OS Successful [0001.399] NvTbootPackSdramParams: start. [0001.404] NvTbootPackSdramParams: done. [0001.408] Tegraboot started after 734096 us [0001.412] Basic modules init took 348709 us [0001.416] Sec Bootdevice Read Time = 202 ms, Read Size = 8459 KB [0001.422] Next stage binary read took 14367 us [0001.426] Carveout took 252686 us [0001.429] CPU initialization took 92425 us [0001.433] Total time taken by TegraBoot 708187 us [0001.438] Starting CPU & Halting co-processor 64b[0001.573] LPDDR4 Training: Number of tables = 10 [0001.577] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.584] EMC Training Successful [0001.587] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.593] EMC Training Successful [0001.596] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.607] EMC Training Successful [0001.610] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.633] EMC Training Successful [0001.636] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.657] EMC Training Successful [0001.660] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.680] EMC Training Successful [0001.683] Switching to 800000 KHz Success [0001.716] LPDDR4 Training: Number of tables = 10 U-Boot 2015.07-rc2-g2ac3917 (Nov 09 2015 - 13:12:08 -0800) TEGRA210 Model: NVIDIA P2371-0000 DRAM: 3 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0x1d5a000 |/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/CTRL+C - Operation aborted Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # env set fdt_copy_node_names /cpus:/psci Tegra210 (P2371-0000) # setenv rootpart 1 Tegra210 (P2371-0000) # setenv devtype mmc Tegra210 (P2371-0000) # setenv devnum 0 Tegra210 (P2371-0000) # part uuid ${devtype} ${devnum}:${rootpart} uuid Tegra210 (P2371-0000) # setenv bootargs ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${kernel_addr_r} /boot/Image.defconfig%jetson-tx1 16710144 bytes read in 852 ms (18.7 MiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${fdt_addr_r} /boot/tegra210-p2371-0000.dtb 44764 bytes read in 453 ms (95.7 KiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${ramdisk_addr_r} /boot/tegra-ramdisk.img 1627787 bytes read in 495 ms (3.1 MiB/s) Tegra210 (P2371-0000) # ramdisk_size=${filesize} Tegra210 (P2371-0000) # booti ${kernel_addr_r} - ${fdt_addr_r} ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200dedb Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd071] [ 0.000000] Linux version 4.15.0-rc4-14859-g1291a0d5 (jonathanh@kaivo) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09)) #1 SMP PREEMPT Sun Dec 17 19:36:49 PST 2017 [ 0.000000] Machine model: NVIDIA Tegra210 P2371 (P2530/P2595) reference design [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000fe000000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000013fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x13ffb6e00-0x13ffb88ff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ff1fffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000013fffffff] [ 0.000000] On node 0 totalpages: 782848 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 520704 pages, LIFO batch:31 [ 0.000000] Normal zone: 4096 pages used for memmap [ 0.000000] Normal zone: 262144 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 23 pages/cpu @ (ptrval) s55168 r8192 d30848 u94208 [ 0.000000] pcpu-alloc: s55168 r8192 d30848 u94208 alloc=23*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] CPU features: enabling workaround for ARM erratum 834220 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 770560 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash [ 0.000000] software IO TLB [mem 0xfa000000-0xfe000000] (64MB) mapped at [ (ptrval)- (ptrval)] [ 0.000000] Memory: 2982428K/3131392K available (9468K kernel code, 1150K rwdata, 4596K rodata, 1088K init, 395K bss, 132580K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB) [ 0.000000] .text : 0x (ptrval) - 0x (ptrval) ( 9472 KB) [ 0.000000] .rodata : 0x (ptrval) - 0x (ptrval) ( 4608 KB) [ 0.000000] .init : 0x (ptrval) - 0x (ptrval) ( 1088 KB) [ 0.000000] .data : 0x (ptrval) - 0x (ptrval) ( 1151 KB) [ 0.000000] .bss : 0x (ptrval) - 0x (ptrval) ( 396 KB) [ 0.000000] fixed : 0xffff7dfffe7fb000 - 0xffff7dfffec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum) [ 0.000000] 0xffff7e0000000000 - 0xffff7e0003000000 ( 48 MB actual) [ 0.000000] memory : 0xffff800000000000 - 0xffff8000c0000000 ( 3072 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] boot misc1 0x0: expected 0x20 [ 0.000000] (comparison mask = 0xffffff) [ 0.000000] PLL_X already enabled. Postponing set full defaults [ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.008441] Console: colour dummy device 80x25 [ 0.013093] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.023720] pid_max: default: 32768 minimum: 301 [ 0.028566] Security Framework initialized [ 0.034961] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.043511] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.050867] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.057838] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.081292] ASID allocator initialised with 65536 entries [ 0.086962] Hierarchical SRCU implementation. [ 0.100504] Speedo Revision 4 [ 0.103602] Tegra Revision: A01 SKU: 1 CPU Process: -22 SoC Process: -22 [ 0.111435] EFI services will not be available. [ 0.124152] smp: Bringing up secondary CPUs ... [ 0.156984] Detected PIPT I-cache on CPU1 [ 0.157029] CPU1: Booted secondary processor 0x0000000001 [0x411fd071] [ 0.185040] Detected PIPT I-cache on CPU2 [ 0.185074] CPU2: Booted secondary processor 0x0000000002 [0x411fd071] [ 0.213102] Detected PIPT I-cache on CPU3 [ 0.213136] CPU3: Booted secondary processor 0x0000000003 [0x411fd071] [ 0.213213] smp: Brought up 1 node, 4 CPUs [ 0.250151] SMP: Total of 4 processors activated. [ 0.255022] CPU features: detected feature: 32-bit EL0 Support [ 0.261386] CPU: All CPU(s) started at EL2 [ 0.265640] alternatives: patching kernel code [ 0.274599] devtmpfs: initialized [ 0.285513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.295648] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.302587] pinctrl core: initialized pinctrl subsystem [ 0.309452] DMI not present or invalid. [ 0.313756] NET: Registered protocol family 16 [ 0.318689] audit: initializing netlink subsys (disabled) [ 0.324384] audit: type=2000 audit(0.268:1): state=initialized audit_enabled=0 res=1 [ 0.332406] cpuidle: using governor menu [ 0.337402] vdso: 2 pages (1 code @ 00000000d1347484, 1 data @ 00000000b6d94819) [ 0.345083] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.353158] DMA: preallocated 256 KiB pool for atomic allocations [ 0.361815] Serial: AMBA PL011 UART driver [ 0.390623] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.398807] ACPI: Interpreter disabled. [ 0.403580] vgaarb: loaded [ 0.406630] SCSI subsystem initialized [ 0.410785] libata version 3.00 loaded. [ 0.415016] usbcore: registered new interface driver usbfs [ 0.420855] usbcore: registered new interface driver hub [ 0.426427] usbcore: registered new device driver usb [ 0.432740] pps_core: LinuxPPS API ver. 1 registered [ 0.437890] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.447376] PTP clock support registered [ 0.451552] EDAC MC: Ver: 3.0.0 [ 0.455070] dmi: Firmware registration failed. [ 0.459937] Advanced Linux Sound Architecture Driver Initialized. [ 0.466920] clocksource: Switched to clocksource arch_sys_counter [ 0.473384] VFS: Disk quotas dquot_6.6.0 [ 0.477515] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.484777] pnp: PnP ACPI: disabled [ 0.494840] NET: Registered protocol family 2 [ 0.499891] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.507674] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.514783] TCP: Hash tables configured (established 32768 bind 32768) [ 0.521682] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.527966] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.534778] NET: Registered protocol family 1 [ 0.539596] RPC: Registered named UNIX socket transport module. [ 0.545734] RPC: Registered udp transport module. [ 0.550609] RPC: Registered tcp transport module. [ 0.555477] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.562151] PCI: CLS 0 bytes, default 128 [ 0.566953] kvm [1]: 8-bit VMID [ 0.570198] kvm [1]: IDMAP page: 809a6000 [ 0.574355] kvm [1]: HYP VA range: 800000000000:ffffffffffff [ 0.581178] kvm [1]: vgic-v2@50044000 [ 0.585087] kvm [1]: vgic interrupt IRQ1 [ 0.589169] kvm [1]: virtual timer IRQ4 [ 0.593235] kvm [1]: Hyp mode initialized successfully [ 0.601446] Initialise system trusted keyrings [ 0.606162] workingset: timestamp_bits=44 max_order=20 bucket_order=0 [ 0.619059] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.625709] NFS: Registering the id_resolver key type [ 0.630964] Key type id_resolver registered [ 0.635294] Key type id_legacy registered [ 0.639452] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.646524] 9p: Installing v9fs 9p2000 file system support [ 0.654825] Key type asymmetric registered [ 0.659075] Asymmetric key parser 'x509' registered [ 0.664263] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.671921] io scheduler noop registered [ 0.676171] io scheduler cfq registered (default) [ 0.681041] io scheduler mq-deadline registered [ 0.685735] io scheduler kyber registered [ 0.703886] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.713539] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.726492] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.734957] console [ttyS0] disabled [ 0.738697] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 313, base_baud = 25500000) is a Tegra [ 0.747998] console [ttyS0] enabled [ 0.747998] console [ttyS0] enabled [ 0.755090] bootconsole [uart8250] disabled [ 0.755090] bootconsole [uart8250] disabled [ 0.764111] SuperH (H)SCI(F) driver initialized [ 0.768926] msm_serial: driver initialized [ 0.773558] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.785416] loop: module loaded [ 0.791549] libphy: Fixed MDIO Bus: probed [ 0.796104] tun: Universal TUN/TAP device driver, 1.6 [ 0.801717] thunder-xcv, ver 1.0 [ 0.805001] thunder-BGX, ver 1.0 [ 0.808274] thunder-nic, ver 1.0 [ 0.811759] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.817594] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.823560] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.830521] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.836141] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.843968] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.850132] sky2: driver version 1.30 [ 0.854091] usbcore: registered new interface driver r8152 [ 0.859722] VFIO - User Level meta-driver version: 0.3 [ 0.865718] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.872256] ehci-pci: EHCI PCI platform driver [ 0.876743] ehci-platform: EHCI generic platform driver [ 0.882063] ehci-orion: EHCI orion driver [ 0.886143] ehci-exynos: EHCI EXYNOS driver [ 0.890403] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.896593] ohci-pci: OHCI PCI platform driver [ 0.901080] ohci-platform: OHCI generic platform driver [ 0.906412] ohci-exynos: OHCI EXYNOS driver [ 0.910969] usbcore: registered new interface driver usb-storage [ 0.919146] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.926334] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.932681] i2c /dev entries driver [ 0.938935] sdhci: Secure Digital Host Controller Interface driver [ 0.945119] sdhci: Copyright(c) Pierre Ossman [ 0.949653] Synopsys Designware Multimedia Card Interface Driver [ 0.956216] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.970253] mmc0: Unknown controller version (3). You may experience problems. [ 1.022979] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.035162] ledtrig-cpu: registered to indicate activity on CPUs [ 1.042228] usbcore: registered new interface driver usbhid [ 1.047828] usbhid: USB HID core driver [ 1.053556] NET: Registered protocol family 17 [ 1.058185] 9pnet: Installing 9P2000 support [ 1.062550] Key type dns_resolver registered [ 1.067525] registered taskstats version 1 [ 1.071679] Loading compiled-in X.509 certificates [ 1.085533] hctosys: unable to open rtc device (rtc0) [ 1.091200] ALSA device list: [ 1.094191] No soundcards found. [ 1.098028] Waiting for root device PARTUUID=00000000-0001-0000-788f-a75600000000... [ 1.122070] mmc0: new high speed MMC card at address 0001 [ 1.127860] mmcblk0: mmc0:0001 SDW16G 14.7 GiB [ 1.132556] mmcblk0boot0: mmc0:0001 SDW16G partition 1 4.00 MiB [ 1.138616] mmcblk0boot1: mmc0:0001 SDW16G partition 2 4.00 MiB [ 1.144667] mmcblk0rpmb: mmc0:0001 SDW16G partition 3 4.00 MiB, chardev (240:0) [ 1.154048] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.170124] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 1.193585] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.201720] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 1.211185] devtmpfs: mounted [ 1.214807] Freeing unused kernel memory: 1088K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#