U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################### 3.4 MiB/s done Bytes transferred = 8018496 (7a5a40 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.4 MiB/s done Bytes transferred = 67161 (10659 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7a5a40 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83013658 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.0-187049-g569dbb8 (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Sun Sep 3 14:06:13 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c157e840, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 17 pages/cpu @eef81000 s39488 r8192 d21952 u69632 [ 0.000000] pcpu-alloc: s39488 r8192 d21952 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993428K/2096128K available (10240K kernel code, 1562K rwdata, 4452K rodata, 2048K init, 402K bss, 37164K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc15869a8 (1563 kB) [ 0.000000] .bss : 0xc158fcb0 - 0xc15f46fc ( 403 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000044] Switching to timer-based delay loop, resolution 1000ns [ 0.005123] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005143] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005162] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005177] Switching to timer-based delay loop, resolution 83ns [ 0.005667] Console: colour dummy device 80x30 [ 0.005697] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005715] pid_max: default: 32768 minimum: 301 [ 0.005805] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005821] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006281] CPU: Testing write buffer coherency: ok [ 0.006524] /cpus/cpu@0 missing clock-frequency property [ 0.006568] /cpus/cpu@1 missing clock-frequency property [ 0.006611] /cpus/cpu@2 missing clock-frequency property [ 0.006655] /cpus/cpu@3 missing clock-frequency property [ 0.006669] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006962] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.008920] Hierarchical SRCU implementation. [ 0.010796] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011552] EFI services will not be available. [ 0.011698] smp: Bringing up secondary CPUs ... [ 0.012250] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015614] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025655] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035104] smp: Brought up 1 node, 4 CPUs [ 0.035125] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035134] CPU: All CPU(s) started in SVC mode. [ 0.036656] devtmpfs: initialized [ 0.053478] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.053888] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.053908] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.055336] pinctrl core: initialized pinctrl subsystem [ 0.056994] DMI not present or invalid. [ 0.057167] random: get_random_u32 called from bucket_table_alloc+0xe8/0x254 with crng_init=0 [ 0.057258] NET: Registered protocol family 16 [ 0.059366] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.061973] cpuidle: using governor menu [ 0.089182] No ATAGs? [ 0.089305] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.089322] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.096625] Serial: AMBA PL011 UART driver [ 0.113672] AT91: Could not find identification node [ 0.114244] +5V_SYS: supplied by +VDD_MUX [ 0.114534] +3.3V_SYS: supplied by +VDD_MUX [ 0.115206] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.115222] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.115328] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.115343] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.115536] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.115551] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.115651] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.115665] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.115766] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.115780] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.115880] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.115893] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.118909] vgaarb: loaded [ 0.119706] SCSI subsystem initialized [ 0.119869] libata version 3.00 loaded. [ 0.120116] usbcore: registered new interface driver usbfs [ 0.120175] usbcore: registered new interface driver hub [ 0.120236] usbcore: registered new device driver usb [ 0.123792] pps_core: LinuxPPS API ver. 1 registered [ 0.123803] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.123826] PTP clock support registered [ 0.124015] EDAC MC: Ver: 3.0.0 [ 0.124339] dmi: Firmware registration failed. [ 0.127001] clocksource: Switched to clocksource arch_sys_counter [ 0.182328] NET: Registered protocol family 2 [ 0.182835] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.182936] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.183124] TCP: Hash tables configured (established 8192 bind 8192) [ 0.183206] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.183250] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.183402] NET: Registered protocol family 1 [ 0.183734] RPC: Registered named UNIX socket transport module. [ 0.183745] RPC: Registered udp transport module. [ 0.183754] RPC: Registered tcp transport module. [ 0.183764] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.183777] PCI: CLS 0 bytes, default 64 [ 0.185222] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.186978] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.195275] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.196004] NFS: Registering the id_resolver key type [ 0.196028] Key type id_resolver registered [ 0.196037] Key type id_legacy registered [ 0.196080] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.196733] random: fast init done [ 0.197731] bounce: pool size: 64 pages [ 0.197778] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.197789] io scheduler noop registered [ 0.197799] io scheduler deadline registered [ 0.197964] io scheduler cfq registered (default) [ 0.197975] io scheduler mq-deadline registered [ 0.197984] io scheduler kyber registered [ 0.201562] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.201679] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.202153] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.220847] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.220901] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.227087] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.234265] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.236890] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.293107] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.295753] console [ttyS0] disabled [ 0.295793] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.209721] console [ttyS0] enabled [ 1.214053] SuperH (H)SCI(F) driver initialized [ 1.219697] msm_serial: driver initialized [ 1.223976] STMicroelectronics ASC driver initialized [ 1.229918] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.239195] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.253851] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.271783] brd: module loaded [ 1.281360] loop: module loaded [ 1.285707] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.294108] as3722 4-0040: AS3722 with revision 0x1 found [ 1.306088] as3722-sd2: supplied by +5V_SYS [ 1.310742] as3722-sd3: supplied by +5V_SYS [ 1.315124] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.321539] as3722-sd4: supplied by +5V_SYS [ 1.326156] as3722-sd5: supplied by +5V_SYS [ 1.332194] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.338281] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.344477] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.350365] as3722-ldo3: supplied by +3.3V_SYS [ 1.354841] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.362628] as3722-ldo4: supplied by +3.3V_SYS [ 1.367303] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.373487] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.378338] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.385242] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.390915] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.397109] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.410427] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.432788] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.440688] libphy: Fixed MDIO Bus: probed [ 1.445895] CAN device driver interface [ 1.450712] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.457795] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.463619] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.469609] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.476558] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.486009] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.493462] usbcore: registered new interface driver pegasus [ 1.499176] usbcore: registered new interface driver asix [ 1.504603] usbcore: registered new interface driver ax88179_178a [ 1.510741] usbcore: registered new interface driver cdc_ether [ 1.516614] usbcore: registered new interface driver smsc75xx [ 1.522426] usbcore: registered new interface driver smsc95xx [ 1.528216] usbcore: registered new interface driver net1080 [ 1.533902] usbcore: registered new interface driver cdc_subset [ 1.539862] usbcore: registered new interface driver zaurus [ 1.545482] usbcore: registered new interface driver cdc_ncm [ 1.551384] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.558893] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.565411] ehci-pci: EHCI PCI platform driver [ 1.569908] ehci-platform: EHCI generic platform driver [ 1.575342] ehci-orion: EHCI orion driver [ 1.579527] SPEAr-ehci: EHCI SPEAr driver [ 1.583675] ehci-st: EHCI STMicroelectronics driver [ 1.588711] ehci-exynos: EHCI EXYNOS driver [ 1.593053] ehci-atmel: EHCI Atmel driver [ 1.597213] tegra-ehci: Tegra EHCI driver [ 1.604062] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.609495] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.617264] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.647024] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.653721] hub 1-0:1.0: USB hub found [ 1.657542] hub 1-0:1.0: 1 port detected [ 1.661995] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.668212] ohci-pci: OHCI PCI platform driver [ 1.672691] ohci-platform: OHCI generic platform driver [ 1.678135] SPEAr-ohci: OHCI SPEAr driver [ 1.682281] ohci-st: OHCI STMicroelectronics driver [ 1.687315] ohci-atmel: OHCI Atmel driver [ 1.692112] usbcore: registered new interface driver usb-storage [ 1.702712] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.709607] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.718046] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.725206] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.731930] i2c /dev entries driver [ 1.742426] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.760003] sdhci: Secure Digital Host Controller Interface driver [ 1.766175] sdhci: Copyright(c) Pierre Ossman [ 1.772193] Synopsys Designware Multimedia Card Interface Driver [ 1.779580] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.786037] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.790948] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.812196] mmc0: Unknown controller version (3). You may experience problems. [ 1.819469] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.887025] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.896369] ledtrig-cpu: registered to indicate activity on CPUs [ 1.902713] usbcore: registered new interface driver usbhid [ 1.908298] usbhid: USB HID core driver [ 1.916272] NET: Registered protocol family 10 [ 1.921539] Segment Routing with IPv6 [ 1.925283] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.931778] NET: Registered protocol family 17 [ 1.936224] can: controller area network core (rev 20170425 abi 9) [ 1.942471] NET: Registered protocol family 29 [ 1.946910] can: raw protocol (rev 20170425) [ 1.951194] can: broadcast manager protocol (rev 20170425 t) [ 1.956851] can: netlink gateway (rev 20170425) max_hops=1 [ 1.962652] Key type dns_resolver registered [ 1.967527] ThumbEE CPU extension supported. [ 1.971798] Registering SWP/SWPB emulation handler [ 1.994073] +3.3V_RUN: supplied by +3.3V_SYS [ 2.000022] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.004669] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.010850] +5V_USB_HS: supplied by +5V_SYS [ 2.016529] +3.3V_LP0: supplied by +3.3V_SYS [ 2.025882] +5V_HDMI_CON: supplied by +5V_SYS [ 2.031027] +5V_SATA: supplied by +5V_SYS [ 2.035572] +12V_SATA: supplied by +VDD_MUX [ 2.041246] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.048165] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.055199] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.063220] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.068888] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.078331] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.088534] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.100589] as3722-sd2: supplied by +5V_SYS [ 2.105135] as3722-sd3: supplied by +5V_SYS [ 2.109650] as3722-sd4: supplied by +5V_SYS [ 2.114181] as3722-sd5: supplied by +5V_SYS [ 2.120368] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.126229] as3722-ldo1: supplied by +3.3V_RUN [ 2.131125] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.136798] as3722-ldo3: supplied by +3.3V_SYS [ 2.142329] as3722-ldo4: supplied by +3.3V_SYS [ 2.147152] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.152110] as3722-ldo6: supplied by +3.3V_RUN [ 2.156797] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.162296] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.169551] as3722-ldo9: supplied by +5V_SYS [ 2.174656] mmc0: new high speed MMC card at address 0001 [ 2.180538] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.185625] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.191725] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.198245] as3722-ldo10: supplied by +5V_SYS [ 2.202722] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.209249] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.215399] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.221850] as3722-ldo11: supplied by +3.3V_RUN [ 2.226978] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.235491] mmcblk0: p1 [ 2.240909] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.250011] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.260092] scsi host0: tegra-ahci [ 2.264095] scsi host1: tegra-ahci [ 2.267823] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.275817] ata2: DUMMY [ 2.281690] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.287147] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.294881] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.327041] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.333871] hub 2-0:1.0: USB hub found [ 2.337722] hub 2-0:1.0: 1 port detected [ 2.344197] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.349150] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.361232] mmc1: Unknown controller version (3). You may experience problems. [ 2.368568] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.437572] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.445688] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.453315] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.463039] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.487206] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.495544] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.509356] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.515635] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.521861] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.528780] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.536096] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.541661] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.547733] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.557429] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.567166] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.576937] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.586745] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.593404] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.603447] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.609511] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.611565] ata1: SATA link down (SStatus 0 SControl 300) [ 2.624591] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.634312] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.644081] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.653864] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.660491] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.670511] PCI: bus0: Fast back to back transfers disabled [ 2.676081] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.684105] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.692308] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.698394] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.705366] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.726816] mmc1: new high speed SDHC card at address aaaa [ 2.733048] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.737890] PCI: bus1: Fast back to back transfers disabled [ 2.743490] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.750367] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.756422] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.762064] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.768900] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.776268] pci 0000:02:00.0: supports D1 D2 [ 2.780576] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.798635] mmcblk1: p1 p2 p3 [ 2.817159] PCI: bus2: Fast back to back transfers disabled [ 2.822738] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.829418] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.836199] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.843005] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.850796] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.856907] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.864277] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.869260] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.876052] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.883832] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.891203] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.897327] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.902294] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.908425] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.915207] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.923013] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.930127] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.936479] pcieport 0000:00:01.0: Signaling PME with IRQ 393 [ 2.942380] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.949480] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.955808] pcieport 0000:00:02.0: Signaling PME with IRQ 394 [ 2.961943] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.967557] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.998699] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b72000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 3.008373] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.020679] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.028474] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.035088] [drm] No driver support for vblank timestamp query. [ 3.164484] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.412394] Console: switching to colour frame buffer device 512x135 [ 3.510966] drm drm: fb0: frame buffer device [ 3.515494] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.523405] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 3.531475] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.538803] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.547912] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.555183] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:02:30 UTC (946684950) [ 3.564113] +USB0_VBUS_SW: disabling [ 3.567728] +1.8V_RUN_CAM: disabling [ 3.571499] +2.8V_RUN_CAM: disabling [ 3.575227] +1.2V_RUN_CAM_FRONT: disabling [ 3.579583] +1.05V_RUN_CAM_REAR: disabling [ 3.583832] +3.3V_RUN_TOUCH: disabling [ 3.587802] +2.8V_RUN_CAM_AF: disabling [ 3.591788] +1.8V_RUN_VPP_FUSE: disabling [ 3.596812] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.640295] EXT4-fs (mmcblk0p1): recovery complete [ 3.645972] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.654097] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.664194] devtmpfs: mounted [ 3.667822] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#