U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 3.6 MiB/s done Bytes transferred = 7537304 (730298 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 337.9 KiB/s done Bytes transferred = 67133 (1063d hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x730298 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8301363c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.0-rc6-156693-g39da7c5 (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Tue Apr 11 05:33:37 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c15381c0, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 16 pages/cpu @eef86000 s34432 r8192 d22912 u65536 [ 0.000000] pcpu-alloc: s34432 r8192 d22912 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993652K/2096128K available (10240K kernel code, 1254K rwdata, 4212K rodata, 2048K init, 536K bss, 36940K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc1539ae0 (1255 kB) [ 0.000000] .bss : 0xc153b000 - 0xc15c12b8 ( 537 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000031] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000047] Switching to timer-based delay loop, resolution 1000ns [ 0.005466] arm_arch_timer: Architected cp15 timer(s) running at 12.00MHz (virt). [ 0.005485] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005504] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005518] Switching to timer-based delay loop, resolution 83ns [ 0.005982] Console: colour dummy device 80x30 [ 0.006011] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.006030] pid_max: default: 32768 minimum: 301 [ 0.006137] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006149] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006630] CPU: Testing write buffer coherency: ok [ 0.006878] /cpus/cpu@0 missing clock-frequency property [ 0.006923] /cpus/cpu@1 missing clock-frequency property [ 0.006966] /cpus/cpu@2 missing clock-frequency property [ 0.007011] /cpus/cpu@3 missing clock-frequency property [ 0.007025] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007311] Setting up static identity map for 0x80300000 - 0x80300098 [ 0.011095] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011762] EFI services will not be available. [ 0.012000] smp: Bringing up secondary CPUs ... [ 0.012586] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015676] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025683] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035134] smp: Brought up 1 node, 4 CPUs [ 0.035157] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035165] CPU: All CPU(s) started in SVC mode. [ 0.036638] devtmpfs: initialized [ 0.052987] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.053392] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.053412] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.054823] pinctrl core: initialized pinctrl subsystem [ 0.056781] NET: Registered protocol family 16 [ 0.058851] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.061391] cpuidle: using governor menu [ 0.088884] No ATAGs? [ 0.089010] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.089027] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.095641] Serial: AMBA PL011 UART driver [ 0.112097] +5V_SYS: supplied by +VDD_MUX [ 0.112369] +3.3V_SYS: supplied by +VDD_MUX [ 0.112969] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.112987] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.113076] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.113090] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.113253] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.113267] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.113351] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.113365] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.113451] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.113465] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.113551] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.113565] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.116722] vgaarb: loaded [ 0.117495] SCSI subsystem initialized [ 0.117660] libata version 3.00 loaded. [ 0.117907] usbcore: registered new interface driver usbfs [ 0.117967] usbcore: registered new interface driver hub [ 0.118028] usbcore: registered new device driver usb [ 0.121462] pps_core: LinuxPPS API ver. 1 registered [ 0.121474] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.121500] PTP clock support registered [ 0.121684] EDAC MC: Ver: 3.0.0 [ 0.124561] clocksource: Switched to clocksource arch_sys_counter [ 0.134357] NET: Registered protocol family 2 [ 0.134870] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.134971] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.135159] TCP: Hash tables configured (established 8192 bind 8192) [ 0.135240] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.135284] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.135431] NET: Registered protocol family 1 [ 0.135723] RPC: Registered named UNIX socket transport module. [ 0.135734] RPC: Registered udp transport module. [ 0.135742] RPC: Registered tcp transport module. [ 0.135750] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.135762] PCI: CLS 0 bytes, default 64 [ 0.136951] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.138735] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.147397] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.148110] NFS: Registering the id_resolver key type [ 0.148145] Key type id_resolver registered [ 0.148155] Key type id_legacy registered [ 0.148200] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.149742] bounce: pool size: 64 pages [ 0.149784] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.149795] io scheduler noop registered [ 0.149805] io scheduler deadline registered [ 0.149973] io scheduler cfq registered (default) [ 0.149984] io scheduler mq-deadline registered [ 0.155188] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.155315] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.155696] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.171538] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 0.171593] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 0.177804] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.185145] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.187129] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.241887] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.244438] console [ttyS0] disabled [ 0.244476] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.133077] console [ttyS0] enabled [ 1.137417] SuperH (H)SCI(F) driver initialized [ 1.142899] msm_serial: driver initialized [ 1.147211] STMicroelectronics ASC driver initialized [ 1.153103] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.162376] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.177802] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.196853] brd: module loaded [ 1.207027] loop: module loaded [ 1.211346] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.219604] as3722 4-0040: AS3722 with revision 0x1 found [ 1.231434] as3722-sd2: supplied by +5V_SYS [ 1.236075] as3722-sd3: supplied by +5V_SYS [ 1.240457] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.246852] as3722-sd4: supplied by +5V_SYS [ 1.251483] as3722-sd5: supplied by +5V_SYS [ 1.257507] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.263553] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.269795] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.275678] as3722-ldo3: supplied by +3.3V_SYS [ 1.280153] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.287923] as3722-ldo4: supplied by +3.3V_SYS [ 1.292586] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.298791] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.303615] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.310532] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.316205] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.322382] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.334832] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.354322] random: fast init done [ 1.357872] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.365690] libphy: Fixed MDIO Bus: probed [ 1.370862] CAN device driver interface [ 1.375711] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.382722] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.388562] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.394530] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.401498] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.410641] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.418099] usbcore: registered new interface driver pegasus [ 1.423800] usbcore: registered new interface driver asix [ 1.429243] usbcore: registered new interface driver ax88179_178a [ 1.435382] usbcore: registered new interface driver cdc_ether [ 1.441257] usbcore: registered new interface driver smsc75xx [ 1.447065] usbcore: registered new interface driver smsc95xx [ 1.452837] usbcore: registered new interface driver net1080 [ 1.458541] usbcore: registered new interface driver cdc_subset [ 1.464486] usbcore: registered new interface driver zaurus [ 1.470120] usbcore: registered new interface driver cdc_ncm [ 1.476003] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.483348] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.489883] ehci-pci: EHCI PCI platform driver [ 1.494363] ehci-platform: EHCI generic platform driver [ 1.499805] ehci-orion: EHCI orion driver [ 1.503945] SPEAr-ehci: EHCI SPEAr driver [ 1.508104] ehci-st: EHCI STMicroelectronics driver [ 1.513121] ehci-exynos: EHCI EXYNOS driver [ 1.517475] ehci-atmel: EHCI Atmel driver [ 1.521614] tegra-ehci: Tegra EHCI driver [ 1.528457] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.533870] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.541659] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.574581] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.581311] hub 1-0:1.0: USB hub found [ 1.585113] hub 1-0:1.0: 1 port detected [ 1.589602] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.595819] ohci-pci: OHCI PCI platform driver [ 1.600304] ohci-platform: OHCI generic platform driver [ 1.605712] ohci-omap3: OHCI OMAP3 driver [ 1.609849] SPEAr-ohci: OHCI SPEAr driver [ 1.613991] ohci-st: OHCI STMicroelectronics driver [ 1.619013] ohci-atmel: OHCI Atmel driver [ 1.623782] usbcore: registered new interface driver usb-storage [ 1.634097] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.640997] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.649177] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.656360] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.663054] i2c /dev entries driver [ 1.673201] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.690449] sdhci: Secure Digital Host Controller Interface driver [ 1.696649] sdhci: Copyright(c) Pierre Ossman [ 1.702600] Synopsys Designware Multimedia Card Interface Driver [ 1.709768] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.716196] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.721083] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.726225] mmc0: Unknown controller version (3). You may experience problems. [ 1.733515] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.804582] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.813878] ledtrig-cpu: registered to indicate activity on CPUs [ 1.820214] usbcore: registered new interface driver usbhid [ 1.825798] usbhid: USB HID core driver [ 1.833698] NET: Registered protocol family 10 [ 1.839005] Segment Routing with IPv6 [ 1.842715] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.849205] NET: Registered protocol family 17 [ 1.853649] can: controller area network core (rev 20120528 abi 9) [ 1.860010] NET: Registered protocol family 29 [ 1.864449] can: raw protocol (rev 20120528) [ 1.868733] can: broadcast manager protocol (rev 20161123 t) [ 1.874390] can: netlink gateway (rev 20130117) max_hops=1 [ 1.880198] Key type dns_resolver registered [ 1.885029] ThumbEE CPU extension supported. [ 1.889300] Registering SWP/SWPB emulation handler [ 1.907686] +3.3V_RUN: supplied by +3.3V_SYS [ 1.913227] +USB0_VBUS_SW: supplied by +5V_SYS [ 1.918006] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.923995] +5V_USB_HS: supplied by +5V_SYS [ 1.929971] +3.3V_LP0: supplied by +3.3V_SYS [ 1.936447] +5V_HDMI_CON: supplied by +5V_SYS [ 1.941496] +5V_SATA: supplied by +5V_SYS [ 1.946045] +12V_SATA: supplied by +VDD_MUX [ 1.952195] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.956165] mmc0: new high speed MMC card at address 0001 [ 1.957532] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 1.958327] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 1.958701] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 1.959856] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 1.970689] mmcblk0: p1 [ 1.989333] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 1.996418] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.004334] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.010971] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 2.022095] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.032810] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.043565] as3722-sd2: supplied by +5V_SYS [ 2.048132] as3722-sd3: supplied by +5V_SYS [ 2.052543] as3722-sd4: supplied by +5V_SYS [ 2.057096] as3722-sd5: supplied by +5V_SYS [ 2.062993] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.068870] as3722-ldo1: supplied by +3.3V_RUN [ 2.073659] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.079211] as3722-ldo3: supplied by +3.3V_SYS [ 2.084523] as3722-ldo4: supplied by +3.3V_SYS [ 2.089397] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.094345] as3722-ldo6: supplied by +3.3V_RUN [ 2.099181] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.104690] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.111772] as3722-ldo9: supplied by +5V_SYS [ 2.117560] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.124092] as3722-ldo10: supplied by +5V_SYS [ 2.129050] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.135907] as3722-ldo11: supplied by +3.3V_RUN [ 2.141200] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.151146] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.160220] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.170781] scsi host0: tegra-ahci [ 2.175335] scsi host1: tegra-ahci [ 2.179038] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.187076] ata2: DUMMY [ 2.192385] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.197834] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.205635] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.234680] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.241724] hub 2-0:1.0: USB hub found [ 2.245579] hub 2-0:1.0: 1 port detected [ 2.251886] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.256838] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.261912] mmc1: Unknown controller version (3). You may experience problems. [ 2.269248] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.335114] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.343206] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.351721] tegra-pcie 1003000.pcie-controller: probing port 0, using 2 lanes [ 2.361227] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000008 [ 2.384635] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 2.393844] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000000 [ 2.408567] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.415835] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.422024] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.428929] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.436280] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.441808] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.447904] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.457725] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.467547] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.474173] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.484226] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.490324] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.500133] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.509955] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.516624] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.526645] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.528359] ata1: SATA link down (SStatus 0 SControl 300) [ 2.541814] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.551560] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.561221] pci_bus 0000:00: 1-byte config write to 0000:00:01.0 offset 0xc may corrupt adjacent RW1C bits [ 2.570911] PCI: bus0: Fast back to back transfers disabled [ 2.576504] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.584522] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.592807] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.598900] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.605911] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.628462] mmc1: new high speed SDHC card at address aaaa [ 2.634694] PCI: bus1: Fast back to back transfers disabled [ 2.640295] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.647177] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.653213] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.658855] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.665673] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.673044] pci 0000:02:00.0: supports D1 D2 [ 2.677329] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.684249] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.702085] mmcblk1: p1 p2 p3 [ 2.705379] PCI: bus2: Fast back to back transfers disabled [ 2.710975] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.717816] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.724657] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.731456] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.739235] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.745356] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.752697] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.757702] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.764502] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.772277] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.779641] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.785761] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.790735] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.796869] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.803653] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.811439] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.818531] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.824890] pcieport 0000:00:01.0: Signaling PME with IRQ 393 [ 2.830730] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.837813] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.844151] pcieport 0000:00:02.0: Signaling PME with IRQ 394 [ 2.850218] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.855857] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.886278] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b56000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 2.895975] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.908930] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.916747] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.923362] [drm] No driver support for vblank timestamp query. [ 3.050066] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.296605] Console: switching to colour frame buffer device 512x135 [ 3.395213] drm drm: fb0: frame buffer device [ 3.399741] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.407622] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 3.415703] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.423018] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.432255] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.439542] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:13 UTC (946684813) [ 3.448688] +USB0_VBUS_SW: disabling [ 3.452264] +1.8V_RUN_CAM: disabling [ 3.456100] +2.8V_RUN_CAM: disabling [ 3.459952] +1.2V_RUN_CAM_FRONT: disabling [ 3.464210] +1.05V_RUN_CAM_REAR: disabling [ 3.468566] +3.3V_RUN_TOUCH: disabling [ 3.472473] +2.8V_RUN_CAM_AF: disabling [ 3.476549] +1.8V_RUN_VPP_FUSE: disabling [ 3.481652] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.523145] EXT4-fs (mmcblk0p1): recovery complete [ 3.528845] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.536963] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.547062] devtmpfs: mounted [ 3.550764] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#