U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 3.9 MiB/s done Bytes transferred = 7536112 (72fdf0 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.8 MiB/s done Bytes transferred = 67133 (1063d hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x72fdf0 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8301363c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.0-rc5-156411-ga71c9a1 (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Sun Apr 2 18:05:00 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c15381c0, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 16 pages/cpu @eef86000 s34432 r8192 d22912 u65536 [ 0.000000] pcpu-alloc: s34432 r8192 d22912 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993652K/2096128K available (10240K kernel code, 1254K rwdata, 4212K rodata, 2048K init, 536K bss, 36940K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc1539ae0 (1255 kB) [ 0.000000] .bss : 0xc153b000 - 0xc15c12b8 ( 537 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000032] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000048] Switching to timer-based delay loop, resolution 1000ns [ 0.005409] arm_arch_timer: Architected cp15 timer(s) running at 12.00MHz (virt). [ 0.005428] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005448] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005462] Switching to timer-based delay loop, resolution 83ns [ 0.005930] Console: colour dummy device 80x30 [ 0.005960] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005979] pid_max: default: 32768 minimum: 301 [ 0.006087] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006100] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006577] CPU: Testing write buffer coherency: ok [ 0.006827] /cpus/cpu@0 missing clock-frequency property [ 0.006872] /cpus/cpu@1 missing clock-frequency property [ 0.006915] /cpus/cpu@2 missing clock-frequency property [ 0.006959] /cpus/cpu@3 missing clock-frequency property [ 0.006972] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007260] Setting up static identity map for 0x80300000 - 0x80300098 [ 0.011121] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011793] EFI services will not be available. [ 0.012029] smp: Bringing up secondary CPUs ... [ 0.012540] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015542] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025552] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035084] smp: Brought up 1 node, 4 CPUs [ 0.035106] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035115] CPU: All CPU(s) started in SVC mode. [ 0.036607] devtmpfs: initialized [ 0.052393] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.052793] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.052811] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.054222] pinctrl core: initialized pinctrl subsystem [ 0.056149] NET: Registered protocol family 16 [ 0.058212] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.060678] cpuidle: using governor menu [ 0.087457] No ATAGs? [ 0.087583] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.087599] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.094122] Serial: AMBA PL011 UART driver [ 0.110212] +5V_SYS: supplied by +VDD_MUX [ 0.110479] +3.3V_SYS: supplied by +VDD_MUX [ 0.111070] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.111086] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.111174] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.111189] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.111351] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.111365] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.111451] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.111465] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.111550] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.111564] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.111648] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.111661] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.114787] vgaarb: loaded [ 0.115572] SCSI subsystem initialized [ 0.115736] libata version 3.00 loaded. [ 0.115975] usbcore: registered new interface driver usbfs [ 0.116032] usbcore: registered new interface driver hub [ 0.116091] usbcore: registered new device driver usb [ 0.119490] pps_core: LinuxPPS API ver. 1 registered [ 0.119501] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.119524] PTP clock support registered [ 0.119706] EDAC MC: Ver: 3.0.0 [ 0.122551] clocksource: Switched to clocksource arch_sys_counter [ 0.132144] NET: Registered protocol family 2 [ 0.132667] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.132768] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.132956] TCP: Hash tables configured (established 8192 bind 8192) [ 0.133037] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.133081] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.133230] NET: Registered protocol family 1 [ 0.133520] RPC: Registered named UNIX socket transport module. [ 0.133531] RPC: Registered udp transport module. [ 0.133541] RPC: Registered tcp transport module. [ 0.133550] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.133562] PCI: CLS 0 bytes, default 64 [ 0.134751] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.136476] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.144580] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.145264] NFS: Registering the id_resolver key type [ 0.145287] Key type id_resolver registered [ 0.145296] Key type id_legacy registered [ 0.145339] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.146801] bounce: pool size: 64 pages [ 0.146842] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.146853] io scheduler noop registered [ 0.146864] io scheduler deadline registered [ 0.147026] io scheduler cfq registered (default) [ 0.147037] io scheduler mq-deadline registered [ 0.152130] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.152253] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.152662] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.168640] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 0.168695] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 0.174918] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.182139] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.184150] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.237591] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.240095] console [ttyS0] disabled [ 0.240133] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.128782] console [ttyS0] enabled [ 1.133130] SuperH (H)SCI(F) driver initialized [ 1.138624] msm_serial: driver initialized [ 1.142925] STMicroelectronics ASC driver initialized [ 1.148799] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.158049] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.173428] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.192169] brd: module loaded [ 1.202165] loop: module loaded [ 1.206513] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.214763] as3722 4-0040: AS3722 with revision 0x1 found [ 1.226463] as3722-sd2: supplied by +5V_SYS [ 1.231070] as3722-sd3: supplied by +5V_SYS [ 1.235569] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.241914] as3722-sd4: supplied by +5V_SYS [ 1.246557] as3722-sd5: supplied by +5V_SYS [ 1.252575] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.258609] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.264842] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.270715] as3722-ldo3: supplied by +3.3V_SYS [ 1.275213] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.282961] as3722-ldo4: supplied by +3.3V_SYS [ 1.287624] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.293825] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.298643] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.305565] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.311217] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.317416] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.329811] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.349122] random: fast init done [ 1.352701] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.360437] libphy: Fixed MDIO Bus: probed [ 1.365674] CAN device driver interface [ 1.370410] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.377431] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.383273] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.389244] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.396207] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.405340] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.412789] usbcore: registered new interface driver pegasus [ 1.418488] usbcore: registered new interface driver asix [ 1.423931] usbcore: registered new interface driver ax88179_178a [ 1.430049] usbcore: registered new interface driver cdc_ether [ 1.435935] usbcore: registered new interface driver smsc75xx [ 1.441725] usbcore: registered new interface driver smsc95xx [ 1.447514] usbcore: registered new interface driver net1080 [ 1.453214] usbcore: registered new interface driver cdc_subset [ 1.459158] usbcore: registered new interface driver zaurus [ 1.464792] usbcore: registered new interface driver cdc_ncm [ 1.470653] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.478000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.484537] ehci-pci: EHCI PCI platform driver [ 1.489014] ehci-platform: EHCI generic platform driver [ 1.494454] ehci-orion: EHCI orion driver [ 1.498596] SPEAr-ehci: EHCI SPEAr driver [ 1.502759] ehci-st: EHCI STMicroelectronics driver [ 1.507773] ehci-exynos: EHCI EXYNOS driver [ 1.512110] ehci-atmel: EHCI Atmel driver [ 1.516263] tegra-ehci: Tegra EHCI driver [ 1.523096] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.528511] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.536291] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.562579] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.569292] hub 1-0:1.0: USB hub found [ 1.573095] hub 1-0:1.0: 1 port detected [ 1.577582] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.583799] ohci-pci: OHCI PCI platform driver [ 1.588285] ohci-platform: OHCI generic platform driver [ 1.593694] ohci-omap3: OHCI OMAP3 driver [ 1.597831] SPEAr-ohci: OHCI SPEAr driver [ 1.601972] ohci-st: OHCI STMicroelectronics driver [ 1.606995] ohci-atmel: OHCI Atmel driver [ 1.611763] usbcore: registered new interface driver usb-storage [ 1.621948] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.628847] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.637028] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.644211] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.650903] i2c /dev entries driver [ 1.661013] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.678198] sdhci: Secure Digital Host Controller Interface driver [ 1.684399] sdhci: Copyright(c) Pierre Ossman [ 1.690339] Synopsys Designware Multimedia Card Interface Driver [ 1.697508] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.703924] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.708812] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.713946] mmc0: Unknown controller version (3). You may experience problems. [ 1.721240] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.792573] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.801886] ledtrig-cpu: registered to indicate activity on CPUs [ 1.808295] usbcore: registered new interface driver usbhid [ 1.813954] usbhid: USB HID core driver [ 1.822031] NET: Registered protocol family 10 [ 1.827439] Segment Routing with IPv6 [ 1.831229] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.837734] NET: Registered protocol family 17 [ 1.842178] can: controller area network core (rev 20120528 abi 9) [ 1.848527] NET: Registered protocol family 29 [ 1.852984] can: raw protocol (rev 20120528) [ 1.857249] can: broadcast manager protocol (rev 20161123 t) [ 1.862920] can: netlink gateway (rev 20130117) max_hops=1 [ 1.868684] Key type dns_resolver registered [ 1.873497] ThumbEE CPU extension supported. [ 1.877768] Registering SWP/SWPB emulation handler [ 1.895411] +3.3V_RUN: supplied by +3.3V_SYS [ 1.900562] +USB0_VBUS_SW: supplied by +5V_SYS [ 1.905242] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.911145] +5V_USB_HS: supplied by +5V_SYS [ 1.916121] +3.3V_LP0: supplied by +3.3V_SYS [ 1.921465] +5V_HDMI_CON: supplied by +5V_SYS [ 1.926732] +5V_SATA: supplied by +5V_SYS [ 1.931530] +12V_SATA: supplied by +VDD_MUX [ 1.937609] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.944520] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 1.951582] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.959719] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 1.966413] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 1.977217] mmc0: new high speed MMC card at address 0001 [ 1.978575] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 1.983776] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 1.987179] as3722-sd2: supplied by +5V_SYS [ 1.987488] as3722-sd3: supplied by +5V_SYS [ 1.987776] as3722-sd4: supplied by +5V_SYS [ 1.988077] as3722-sd5: supplied by +5V_SYS [ 1.989511] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.990008] as3722-ldo1: supplied by +3.3V_RUN [ 1.990331] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.991272] as3722-ldo3: supplied by +3.3V_SYS [ 1.992206] as3722-ldo4: supplied by +3.3V_SYS [ 1.992526] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.992881] as3722-ldo6: supplied by +3.3V_RUN [ 1.993189] as3722-ldo7: supplied by +1.8V_VDDIO [ 1.993425] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 1.993797] as3722-ldo9: supplied by +5V_SYS [ 1.994198] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 1.994591] as3722-ldo10: supplied by +5V_SYS [ 1.994818] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 1.995192] as3722-ldo11: supplied by +3.3V_RUN [ 1.995418] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 1.998471] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 1.998484] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.003474] scsi host0: tegra-ahci [ 2.004129] scsi host1: tegra-ahci [ 2.004450] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.004455] ata2: DUMMY [ 2.008094] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.008124] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.008329] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.032671] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.043419] hub 2-0:1.0: USB hub found [ 2.043468] hub 2-0:1.0: 1 port detected [ 2.046330] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.046352] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.046551] mmc1: Unknown controller version (3). You may experience problems. [ 2.046652] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.113207] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.114120] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.116696] tegra-pcie 1003000.pcie-controller: probing port 0, using 2 lanes [ 2.119575] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000008 [ 2.148907] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 2.151034] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000000 [ 2.164890] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.164901] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.164908] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.164915] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.164924] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.164967] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.165019] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.165066] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.165117] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.165128] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.165402] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.165451] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.165495] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.165545] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.165556] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.165839] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.165853] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.165867] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.165878] pci_bus 0000:00: 1-byte config write to 0000:00:01.0 offset 0xc may corrupt adjacent RW1C bits [ 2.165892] PCI: bus0: Fast back to back transfers disabled [ 2.165903] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.165924] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.166149] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.166204] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.166433] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.192753] PCI: bus1: Fast back to back transfers disabled [ 2.192767] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.193048] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.193085] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.193128] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.193158] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.193343] pci 0000:02:00.0: supports D1 D2 [ 2.193350] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.222748] PCI: bus2: Fast back to back transfers disabled [ 2.222763] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.222968] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.222979] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.222989] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.222998] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.223012] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.223051] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.223065] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.223087] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.223117] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.223146] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.223160] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.223168] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.223181] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.223192] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.223237] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.223349] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.223644] pcieport 0000:00:01.0: Signaling PME with IRQ 393 [ 2.223771] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.223850] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.224114] pcieport 0000:00:02.0: Signaling PME with IRQ 394 [ 2.224433] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.224460] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.254439] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b41000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 2.254449] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.260359] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.262352] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.262356] [drm] No driver support for vblank timestamp query. [ 2.262396] [drm] Cannot find any crtc or sizes - going 1024x768 [ 2.343410] ata1: SATA link down (SStatus 0 SControl 300) [ 2.377089] mmc1: new high speed SDHC card at address aaaa [ 2.377961] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.388849] mmcblk1: p1 p2 p3 [ 2.683714] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.684451] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.685520] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.686160] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.688644] mmcblk0: p1 [ 2.729303] Console: switching to colour frame buffer device 128x48 [ 2.781422] drm drm: fb0: frame buffer device [ 2.785967] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 2.793832] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 2.801886] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 2.809221] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 2.818350] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.825636] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:02:05 UTC (946684925) [ 2.834772] +USB0_VBUS_SW: disabling [ 2.838349] +1.8V_RUN_CAM: disabling [ 2.842128] +2.8V_RUN_CAM: disabling [ 2.845867] +1.2V_RUN_CAM_FRONT: disabling [ 2.850081] +1.05V_RUN_CAM_REAR: disabling [ 2.854338] +3.3V_RUN_TOUCH: disabling [ 2.858193] +2.8V_RUN_CAM_AF: disabling [ 2.862120] +1.8V_RUN_VPP_FUSE: disabling [ 2.867093] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 2.907406] EXT4-fs (mmcblk0p1): recovery complete [ 2.912986] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 2.921081] VFS: Mounted root (ext3 filesystem) on device 179:17. [ 2.931251] devtmpfs: mounted [ 2.934949] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#