[0000.773] [TegraBoot] (version 23.00.2015.14-mobile-1ef66670) [0000.779] Processing in cold boot mode Bootloader 2 [0000.783] A01Q Bootrom Patch rev = 3 [0000.787] Power-up reason: pmu watchdog [0000.790] No Battery Present [0000.793] Platform has Ddr4 type ram [0000.796] max77620 disabling SD1 Remote Sense [0000.801] Setting Ddr voltage to 1125mv [0000.805] Serial Number of Pmic Max77663: 0x40daf [0000.813] Entering ramdump check [0000.816] Get RamDumpCarveOut = 0x0 [0000.819] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.824] Last reboot was clean, booting normally! [0000.829] Sdram initialization is successful [0000.833] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.838] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.864] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.890] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.895] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.900] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.905] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.911] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.926] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.931] Platform-DebugCarveout: 0 [0000.935] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.984] Using GPT Primary to query partitions [0000.989] Loading Tboot-CPU binary [0001.038] Verifying bootloader in OdmNonSecureSBK mode [0001.048] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.057] Bootloader downloaded successfully. [0001.061] Downloaded Tboot-CPU binary to 0xa0000258 [0001.067] MAX77620_GPIO1 Configured. [0001.071] MAX77620_GPIO5 Configured. [0001.074] CPU power rail is up [0001.077] CPU clock enabled [0001.081] Performing RAM repair [0001.084] Updating A64 Warmreset Address to 0xa00002e9 [0001.103] Bootloader DTB Load Address: 0x83000000 [0001.120] Kernel DTB Load Address: 0x83080000 [0001.125] Loading cboot binary [0001.219] Verifying bootloader in OdmNonSecureSBK mode [0001.307] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0001.316] Bootloader downloaded successfully. [0001.320] GPT: Partition NOT found ! [0001.324] Find Partition via GPT Failed [0001.327] function NvTbootGetBinaryOffsets: 0x845208 error [0001.332] Error in NvTbootLoadBinary: 0x845208 ! [0001.337] GPT: Partition NOT found ! [0001.340] No FB partition [0001.343] Next binary entry address: 0x80110000 [0001.347] BoardId: 2595 [0001.352] dram memory type is 3 [0001.358] WB0 init successful [0001.384] Bpmp FW successfully loaded [0001.388] Set NvDecSticky Bits [0001.391] GSC1 address : ff700000 [0001.395] GSC2 address : ff600000 [0001.399] GSC3 address : ff500000 [0001.402] GSC4 address : ff400000 [0001.406] GSC5 address : ff300000 [0001.409] GSC MC Settings done [0001.415] TOS old plaintext Image length 61440 [0001.421] *** Secure OS image signature not verified *** [0001.426] Loading and Validation of Secure OS Successful [0001.431] NvTbootPackSdramParams: start. [0001.436] NvTbootPackSdramParams: done. [0001.440] Tegraboot started after 766641 us [0001.444] Basic modules init took 348713 us [0001.448] Sec Bootdevice Read Time = 202 ms, Read Size = 8459 KB [0001.454] Next stage binary read took 14387 us [0001.458] Carveout took 252722 us [0001.461] CPU initialization took 92324 us [0001.465] Total time taken by TegraBoot 708146 us [0001.470] Starting CPU & Halting co-processor 64b[0001.605] LPDDR4 Training: Number of tables = 10 [0001.609] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.615] EMC Training Successful [0001.618] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.624] EMC Training Successful [0001.627] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.639] EMC Training Successful [0001.642] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.664] EMC Training Successful [0001.668] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.689] EMC Training Successful [0001.692] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.712] EMC Training Successful [0001.715] Switching to 800000 KHz Success [0001.748] LPDDR4 Training: Number of tables = 10 U-Boot 2015.07-rc2-g2ac3917 (Nov 09 2015 - 13:12:08 -0800) TEGRA210 Model: NVIDIA P2371-0000 DRAM: 3 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0x1d5a000 |/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\CTRL+C - Operation aborted Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # env set fdt_copy_node_names /cpus:/psci Tegra210 (P2371-0000) # setenv rootpart 1 Tegra210 (P2371-0000) # setenv devtype mmc Tegra210 (P2371-0000) # setenv devnum 0 Tegra210 (P2371-0000) # part uuid ${devtype} ${devnum}:${rootpart} uuid Tegra210 (P2371-0000) # setenv bootargs ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${kernel_addr_r} /boot/Image.defconfig 15337984 bytes read in 803 ms (18.2 MiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${fdt_addr_r} /boot/tegra210-p2371-0000.dtb 44882 bytes read in 465 ms (93.8 KiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${ramdisk_addr_r} /boot/tegra-ramdisk.img 1627787 bytes read in 495 ms (3.1 MiB/s) Tegra210 (P2371-0000) # ramdisk_size=${filesize} Tegra210 (P2371-0000) # booti ${kernel_addr_r} - ${fdt_addr_r} ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200df51 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.0-rc2-179788-g4495c08 (pwalmsley@tamien) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sun Mar 12 15:09:02 PDT 2017 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000fe000000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000013fffffff] [ 0.000000] NUMA: Adding memblock [0x80000000 - 0xff1fffff] on node 0 [ 0.000000] NUMA: Adding memblock [0x100000000 - 0x13fffffff] on node 0 [ 0.000000] NUMA: Initmem setup node 0 [mem 0x80000000-0x13fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x13ffad200-0x13ffaecff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ff1fffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000013fffffff] [ 0.000000] On node 0 totalpages: 782848 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 520704 pages, LIFO batch:31 [ 0.000000] Normal zone: 4096 pages used for memmap [ 0.000000] Normal zone: 262144 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 23 pages/cpu @ffff8000bff4e000 s56960 r8192 d29056 u94208 [ 0.000000] pcpu-alloc: s56960 r8192 d29056 u94208 alloc=23*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] CPU features: enabling workaround for ARM erratum 834220 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 770560 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] software IO TLB [mem 0xfa000000-0xfe000000] (64MB) mapped at [ffff80007a000000-ffff80007dffffff] [ 0.000000] Memory: 2983716K/3131392K available (8700K kernel code, 962K rwdata, 4204K rodata, 1088K init, 395K bss, 131292K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB) [ 0.000000] .text : 0xffff000008080000 - 0xffff000008900000 ( 8704 KB) [ 0.000000] .rodata : 0xffff000008900000 - 0xffff000008d20000 ( 4224 KB) [ 0.000000] .init : 0xffff000008d20000 - 0xffff000008e30000 ( 1088 KB) [ 0.000000] .data : 0xffff000008e30000 - 0xffff000008f20a00 ( 963 KB) [ 0.000000] .bss : 0xffff000008f20a00 - 0xffff000008f83638 ( 396 KB) [ 0.000000] fixed : 0xffff7dfffe7fd000 - 0xffff7dfffec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum) [ 0.000000] 0xffff7e0000000000 - 0xffff7e0003000000 ( 48 MB actual) [ 0.000000] memory : 0xffff800000000000 - 0xffff8000c0000000 ( 3072 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] PLL_MB already enabled. Postponing set full defaults [ 0.000000] PLL_U already enabled. Postponing set full defaults [ 0.000000] PLL_P already enabled. Postponing set full defaults [ 0.000000] PLL_X already enabled. Postponing set full defaults [ 0.000000] boot misc1 0x0: expected 0x20 [ 0.000000] (comparison mask = 0xffffff) [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.008440] Console: colour dummy device 80x25 [ 0.013084] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.023707] pid_max: default: 32768 minimum: 301 [ 0.028556] Security Framework initialized [ 0.033789] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.044040] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.052499] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.059443] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.078885] ASID allocator initialised with 65536 entries [ 0.105421] Speedo Revision 4 [ 0.108500] Tegra Revision: A01 SKU: 1 CPU Process: -22 SoC Process: -22 [ 0.116268] EFI services will not be available. [ 0.137007] smp: Bringing up secondary CPUs ... [ 0.173845] Detected PIPT I-cache on CPU1 [ 0.173887] CPU1: Booted secondary processor [411fd071] [ 0.205913] Detected PIPT I-cache on CPU2 [ 0.205946] CPU2: Booted secondary processor [411fd071] [ 0.237989] Detected PIPT I-cache on CPU3 [ 0.238020] CPU3: Booted secondary processor [411fd071] [ 0.238083] smp: Brought up 1 node, 4 CPUs [ 0.270943] SMP: Total of 4 processors activated. [ 0.275813] CPU features: detected feature: 32-bit EL0 Support [ 0.281896] CPU: All CPU(s) started at EL2 [ 0.286156] alternatives: patching kernel code [ 0.294563] devtmpfs: initialized [ 0.305576] DMI not present or invalid. [ 0.309751] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.319888] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.326831] pinctrl core: initialized pinctrl subsystem [ 0.333575] NET: Registered protocol family 16 [ 0.339854] cpuidle: using governor menu [ 0.344607] vdso: 2 pages (1 code @ ffff000008907000, 1 data @ ffff000008e35000) [ 0.352282] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.360315] DMA: preallocated 256 KiB pool for atomic allocations [ 0.368025] Serial: AMBA PL011 UART driver [ 0.392393] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.399874] ACPI: Interpreter disabled. [ 0.404515] vgaarb: loaded [ 0.407526] SCSI subsystem initialized [ 0.412197] libata version 3.00 loaded. [ 0.416415] usbcore: registered new interface driver usbfs [ 0.422155] usbcore: registered new interface driver hub [ 0.427725] usbcore: registered new device driver usb [ 0.433694] pps_core: LinuxPPS API ver. 1 registered [ 0.438842] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.448300] PTP clock support registered [ 0.452505] dmi: Firmware registration failed. [ 0.457255] Advanced Linux Sound Architecture Driver Initialized. [ 0.464169] clocksource: Switched to clocksource arch_sys_counter [ 0.470597] VFS: Disk quotas dquot_6.6.0 [ 0.474716] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.482005] pnp: PnP ACPI: disabled [ 0.492522] NET: Registered protocol family 2 [ 0.497532] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.505322] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.512433] TCP: Hash tables configured (established 32768 bind 32768) [ 0.519331] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.525605] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.532431] NET: Registered protocol family 1 [ 0.537213] RPC: Registered named UNIX socket transport module. [ 0.543345] RPC: Registered udp transport module. [ 0.548220] RPC: Registered tcp transport module. [ 0.553091] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.559761] PCI: CLS 0 bytes, default 128 [ 0.564528] kvm [1]: 8-bit VMID [ 0.567777] kvm [1]: IDMAP page: 808ee000 [ 0.571937] kvm [1]: HYP VA range: 800000000000:ffffffffffff [ 0.578613] kvm [1]: Hyp mode initialized successfully [ 0.583990] kvm [1]: vgic-v2@50044000 [ 0.587888] kvm [1]: vgic interrupt IRQ1 [ 0.591960] kvm [1]: virtual timer IRQ4 [ 0.598109] audit: initializing netlink subsys (disabled) [ 0.603801] audit: type=2000 audit(0.527:1): state=initialized audit_enabled=0 res=1 [ 0.604140] workingset: timestamp_bits=44 max_order=20 bucket_order=0 [ 0.610876] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.611458] NFS: Registering the id_resolver key type [ 0.611476] Key type id_resolver registered [ 0.611479] Key type id_legacy registered [ 0.611490] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.611623] 9p: Installing v9fs 9p2000 file system support [ 0.613888] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.613893] io scheduler noop registered [ 0.614098] io scheduler cfq registered (default) [ 0.614102] io scheduler mq-deadline registered [ 0.633899] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.634888] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.635077] xenfs: not registering filesystem on non-xen platform [ 0.638282] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.639748] console [ttyS0] disabled [ 0.705903] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 312, base_baud = 25500000) is a Tegra [ 0.715232] console [ttyS0] enabled [ 0.715232] console [ttyS0] enabled [ 0.722318] bootconsole [uart8250] disabled [ 0.722318] bootconsole [uart8250] disabled [ 0.731172] SuperH (H)SCI(F) driver initialized [ 0.735948] msm_serial: driver initialized [ 0.740436] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.752465] loop: module loaded [ 0.756147] hisi_sas: driver version v1.6 [ 0.761930] libphy: Fixed MDIO Bus: probed [ 0.766422] tun: Universal TUN/TAP device driver, 1.6 [ 0.771489] tun: (C) 1999-2004 Max Krasnyansky [ 0.778354] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.784234] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.790204] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.797168] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.802791] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.810626] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.816586] sky2: driver version 1.30 [ 0.820614] VFIO - User Level meta-driver version: 0.3 [ 0.826602] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.833136] ehci-pci: EHCI PCI platform driver [ 0.837622] ehci-platform: EHCI generic platform driver [ 0.842932] ehci-exynos: EHCI EXYNOS driver [ 0.847184] ehci-msm: Qualcomm On-Chip EHCI Host Controller [ 0.852814] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.859006] ohci-pci: OHCI PCI platform driver [ 0.863486] ohci-platform: OHCI generic platform driver [ 0.868786] ohci-exynos: OHCI EXYNOS driver [ 0.873282] usbcore: registered new interface driver usb-storage [ 0.880685] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.887866] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.894151] i2c /dev entries driver [ 0.899428] sdhci: Secure Digital Host Controller Interface driver [ 0.905614] sdhci: Copyright(c) Pierre Ossman [ 0.910158] Synopsys Designware Multimedia Card Interface Driver [ 0.916577] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.922510] mmc0: Unknown controller version (3). You may experience problems. [ 0.972229] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.985061] ledtrig-cpu: registered to indicate activity on CPUs [ 0.992177] usbcore: registered new interface driver usbhid [ 0.997766] usbhid: USB HID core driver [ 1.003059] NET: Registered protocol family 17 [ 1.007586] 9pnet: Installing 9P2000 support [ 1.011925] Key type dns_resolver registered [ 1.016758] registered taskstats version 1 [ 1.028122] hctosys: unable to open rtc device (rtc0) [ 1.033712] ALSA device list: [ 1.036688] No soundcards found. [ 1.040321] Waiting for root device PARTUUID=00000000-0001-0000-788f-a75600000000... [ 1.045752] mmc0: new high speed MMC card at address 0001 [ 1.046196] mmcblk0: mmc0:0001 SDW16G 14.7 GiB [ 1.050379] mmcblk0boot0: mmc0:0001 SDW16G partition 1 4.00 MiB [ 1.050548] mmcblk0boot1: mmc0:0001 SDW16G partition 2 4.00 MiB [ 1.050714] mmcblk0rpmb: mmc0:0001 SDW16G partition 3 4.00 MiB [ 1.053339] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.084397] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 1.130103] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.138223] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 1.149600] devtmpfs: mounted [ 1.153178] Freeing unused kernel memory: 1088K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job contr[ 1.316072] random: fast init done ol in this shell root@(none):/#