Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.44 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.95 sec Percent passed so far: 100.0 Final Score: 100.0 |[0025.659] Enabled early print [0025.662] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0025.668] Processing in recovery mode [0025.671] A02 Bootrom Patch rev = 63 [0025.674] Power-up reason: pmc por [0025.678] Established communication link with host [0026.642] Odmdata from BCT: 0x00084000 [0026.645] DebugPort= 0x3 [0026.648] BoardId read from EEPROM/NCT: 2180 [0026.676] Turned on fan for loki board [0026.679] Key release before reqd. time for fastboot [0026.684] No Battery Present [0026.687] RamCode = 0 [0026.689] Platform has Ddr4 type ram [0026.693] max77620 disabling SD1 Remote Sense [0026.697] Setting Ddr voltage to 1125mv [0026.701] Serial Number of Pmic Max77663: 0xb18a4 [0026.708] Entering ramdump check [0026.711] Get RamDumpCarveOut = 0x0 [0026.715] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0026.720] Last reboot was clean, booting normally! [0026.724] Sdram initialization is successful [0026.729] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0026.734] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0026.739] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0026.744] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0026.750] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0026.755] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0026.760] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0026.765] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0026.781] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0026.786] Platform-DebugCarveout: 0 [0026.789] Downloaded Bct successfully [0026.883] Downloaded bootloader successfully at 0x92c00000 [0026.977] Downloaded rp1 successfully at 0x83000000 [0027.016] MAX77620_GPIO1 Configured. [0027.019] MAX77620_GPIO5 Configured. [0027.023] CPU power rail is up [0027.026] CPU clock enabled [0027.029] Performing RAM repair [0027.032] Updating A64 Warmreset Address to 0x92c002e9 [0027.038] Enable APE clock/reset [0027.042] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0027.046] Loading Secure OS image failed. [0027.050] Set NvDecSticky Bits [0027.054] GSC1 address : ff700000 [0027.057] GSC2 address ff63fffc value c0edbbcc [0027.062] GSC2 address : ff600000 [0027.065] GSC3 address : ff500000 [0027.069] GSC4 address : ff400000 [0027.073] GSC5 address : ff300000 [0027.076] GSC MC Settings done [0027.079] NvTbootPackSdramParams: start. [0027.084] NvTbootPackSdramParams: done. [0027.088] Next binary entry address: 0x92c00258 [0027.092] BoardId: 2180 [0027.095] dram memory type is 3 [0027.098] Tegraboot started after 26275512 us [0027.102] Basic modules init took -26275512 us [0027.107] USB data transfer took 0 us [0027.110] Carveout took 27745420 us [0027.114] CPU initialization took 3629 us [0027.117] Total time taken by TegraBoot 1473537 us [0027.122] Starting CPU & Halting co-processor [0027.782] [0027.783] Debug Init done [0027.786] Marked DTB cacheable [0027.789] Bootloader DTB loaded at 0x83000000 [0027.793] DeviceTree Init done [0027.808] Pinmux applied successfully [0027.812] gicd_base: 0x50041000 [0027.816] gicc_base: 0x50042000 [0027.819] Interrupts Init done [0027.824] Using base:0x60005008 & irq:33 for tick-timer [0027.829] Using base:0x60005000 for delay-timer [0027.833] platform_init_timer: DONE [0027.837] Timer(tick) Init done [0027.841] osc freq = 38400 khz [0027.846] [0027.847] welcome to cboot [0027.849] [0027.850] Cboot Version: 24.00.2015.42-t210-63d15635 [0027.855] calling constructors [0027.858] initializing heap [0027.861] initializing threads [0027.864] initializing timers [0027.867] creating bootstrap completion thread [0027.871] top of bootstrap2() [0027.874] CPU: ARM Cortex A57 [0027.877] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0027.882] initializing platform [0027.908] config for ddr50 mode completed [0027.912] sdmmc bdev is already initialized [0027.916] of_register: registering tegra_udc to of_hal [0027.921] of_register: registering inv20628-driver to of_hal [0027.927] of_register: registering ads1015-driver to of_hal [0027.932] of_register: registering lp8557-bl-driver to of_hal [0027.938] of_register: registering bq2419x_charger to of_hal [0027.944] of_register: registering cpc to of_hal [0027.948] of_register: registering bq27441_fuel_gauge to of_hal [0027.963] gpio framework initialized [0027.966] of_register: registering tca9539_gpio to of_hal [0027.971] of_register: registering tca9539_gpio to of_hal [0027.977] of_register: registering i2c_bus_driver to of_hal [0027.982] of_register: registering i2c_bus_driver to of_hal [0027.988] of_register: registering i2c_bus_driver to of_hal [0027.993] pmic framework initialized [0027.997] of_register: registering max77620_pmic to of_hal [0028.002] regulator framework initialized [0028.006] of_register: registering tps65132_bl_driver to of_hal [0028.012] of_register: registering tegra_xhci to of_hal [0028.018] initializing target [0028.024] gpio_driver_register: register 'tegra_gpio_driver' driver [0028.034] fixed regulator driver initialized [0028.099] initializing OF layer [0028.103] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0028.111] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.133] I2C Bus Init done [0028.136] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.147] I2C Bus Init done [0028.150] of_children_init: Ops found for compatible string ti,lp8557 [0028.157] I2C slave not started [0028.160] I2C write failed [0028.162] Writing offset failed [0028.165] failed to read 0x 0 [0028.168] lp8557: Couldn't turn off backlight: -3 [0028.173] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0028.187] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0028.192] gpio_driver_register: register 'tca9539_gpio_driver' driver [0028.199] of_children_init: Ops found for compatible string ti,tca9539 [0028.210] tca9539_init: i2c bus: 2, slave addr: 0xee [0028.215] gpio_driver_register: register 'tca9539_gpio_driver' driver [0028.222] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.234] I2C Bus Init done [0028.236] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.248] I2C Bus Init done [0028.251] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.263] I2C Bus Init done [0028.266] of_children_init: Ops found for compatible string maxim,max77620 [0028.278] max77620_init using irq 118 [0028.283] register 'maxim,max77620' pmic [0028.287] gpio_driver_register: register 'max77620-gpio' driver [0028.294] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0028.306] I2C Bus Init done [0028.308] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0028.317] calling apps_init() [0028.322] Found 19 GPT partitions in "sdmmc3_user" [0028.327] Proceeding to flashing Server [0028.331] usbdcd_reinit Initialize driver to use already enumerated device [0028.338] nv3p_priv_usbf_open USB configuration success [0028.344] Writing GPT partition [0028.348] Erasing Boot device [0028.375] Erasing Storage Device [0028.628] Sanitizing Storage Device [0028.757] Writing protective mbr [0028.761] Writing primary GPT [0028.766] Writing secondary GPT [0028.772] Found 18 GPT partitions in "sdmmc3_user" [0028.777] Writing NVC partition [0028.780] bct_init bctinit [0028.783] bct_init bctinit [0028.791] bct_init bctinit [0028.794] bct_init bctinit [0028.796] bct_init bctinit [0028.831] partition NVC write successful. [0028.835] Writing APP partition [0028.838] bct_init bctinit [0029.671] bct_init bctinit [0029.674] bct_init bctinit [0030.295] partition APP write successful. [0030.300] Writing TBC partition [0030.303] bct_init bctinit [0030.308] bct_init bctinit [0030.310] bct_init bctinit [0030.316] partition TBC write successful. [0030.320] Writing EBT partition [0030.323] bct_init bctinit [0030.342] bct_init bctinit [0030.345] bct_init bctinit [0030.355] partition EBT write successful. [0030.360] Writing BPF partition [0030.363] bct_init bctinit [0030.368] bct_init bctinit [0030.370] bct_init bctinit [0030.376] partition BPF write successful. [0030.380] Writing WB0 partition [0030.383] bct_init bctinit [0030.386] bct_init bctinit [0030.389] bct_init bctinit [0030.393] partition WB0 write successful. [0030.398] Writing RP1 partition [0030.401] bct_init bctinit [0030.417] bct_init bctinit [0030.419] bct_init bctinit [0030.429] partition RP1 write successful. [0030.433] Writing TOS partition [0030.436] bct_init bctinit [0030.441] bct_init bctinit [0030.444] bct_init bctinit [0030.450] partition TOS write successful. [0030.454] Writing DTB partition [0030.457] bct_init bctinit [0030.473] bct_init bctinit [0030.476] bct_init bctinit [0030.487] partition DTB write successful. [0030.495] Writing BCT partition [0030.498] bct_init bctinit [0030.598] partition BCT write successful. [0030.605] Change state to cold boot mode [0030.609] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0xb18a4 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.723] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132119 us [0000.779] Basic modules init took 292392 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12213 us [0000.800] Carveout took 264403 us [0000.803] CPU initialization took 92765 us [0000.807] Total time taken by TegraBoot 661773 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 òô[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0xb18a4 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99070 us [0000.746] Basic modules init took 292156 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12213 us [0000.768] Carveout took 264398 us [0000.771] CPU initialization took 92766 us [0000.775] Total time taken by TegraBoot 661533 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 74 ms (4.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915459 bytes read in 209 ms (31.6 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 447 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11003/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.452701] console [ttyS0] enabled [ 0.452701] console [ttyS0] enabled [ 0.459804] bootconsole [uart0] disabled [ 0.459804] bootconsole [uart0] disabled [ 0.468309] SuperH (H)SCI(F) driver initialized [ 0.473163] msm_serial: driver initialized [ 0.477803] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.488226] loop: module loaded [ 0.492632] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.504368] max77620-sd0: supplied by regulator-dummy [ 0.510703] max77620-sd1: supplied by regulator-dummy [ 0.516843] max77620-sd2: supplied by regulator-dummy [ 0.522766] max77620-sd3: supplied by regulator-dummy [ 0.529155] max77620-ldo0: supplied by regulator-dummy [ 0.535216] max77620-ldo1: supplied by regulator-dummy [ 0.540958] max77620-ldo2: supplied by regulator-dummy [ 0.546964] max77620-ldo3: supplied by regulator-dummy [ 0.552126] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.559011] max77620-ldo4: supplied by regulator-dummy [ 0.564185] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.570759] max77620-ldo5: supplied by regulator-dummy [ 0.575917] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.582900] max77620-ldo6: supplied by regulator-dummy [ 0.588060] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.594941] max77620-ldo7: supplied by regulator-dummy [ 0.600928] max77620-ldo8: supplied by regulator-dummy [ 0.611607] libphy: Fixed MDIO Bus: probed [ 0.616066] tun: Universal TUN/TAP device driver, 1.6 [ 0.621720] thunder_xcv, ver 1.0 [ 0.624981] thunder_bgx, ver 1.0 [ 0.628236] nicpf, ver 1.0 [ 0.631194] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.637023] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.642967] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.649924] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.655523] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.663347] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.669515] sky2: driver version 1.30 [ 0.673471] usbcore: registered new interface driver r8152 [ 0.679050] VFIO - User Level meta-driver version: 0.3 [ 0.684988] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.691514] ehci-pci: EHCI PCI platform driver [ 0.695986] ehci-platform: EHCI generic platform driver [ 0.701302] ehci-orion: EHCI orion driver [ 0.705387] ehci-exynos: EHCI EXYNOS driver [ 0.709640] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.715825] ohci-pci: OHCI PCI platform driver [ 0.720291] ohci-platform: OHCI generic platform driver [ 0.725596] ohci-exynos: OHCI EXYNOS driver [ 0.730296] usbcore: registered new interface driver usb-storage [ 0.869244] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.877457] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.884629] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.890940] i2c /dev entries driver [ 0.897278] sdhci: Secure Digital Host Controller Interface driver [ 0.903459] sdhci: Copyright(c) Pierre Ossman [ 0.907970] Synopsys Designware Multimedia Card Interface Driver [ 0.914600] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.920527] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.941811] mmc0: Unknown controller version (3). You may experience problems. [ 0.980090] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.989028] ledtrig-cpu: registered to indicate activity on CPUs [ 0.995906] usbcore: registered new interface driver usbhid [ 1.001532] usbhid: USB HID core driver [ 1.007014] NET: Registered protocol family 17 [ 1.011537] 9pnet: Installing 9P2000 support [ 1.015870] Key type dns_resolver registered [ 1.020609] registered taskstats version 1 [ 1.024771] Loading compiled-in X.509 certificates [ 1.037255] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.042176] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.047955] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.053272] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.059206] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.065915] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.071155] RTL_5V: supplied by VDD_5V0_SYS [ 1.075585] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.081675] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.086642] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.099813] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.106798] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.113614] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.120413] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.127917] mmc0: new high speed MMC card at address 0001 [ 1.133860] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.138885] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.145243] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.151295] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.158963] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.165947] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.172980] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.180739] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.581807] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.990890] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.399971] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.407469] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.412963] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.421158] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.822747] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.231823] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.640895] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.648391] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.653964] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.660232] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.666427] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.673298] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.680606] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.686573] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.694642] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.703977] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.775068] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.782470] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.787878] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.796444] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.805081] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.811499] hub 1-0:1.0: USB hub found [ 3.815279] hub 1-0:1.0: 5 ports detected [ 3.819624] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.825029] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.832651] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.841038] hub 2-0:1.0: USB hub found [ 3.844815] hub 2-0:1.0: 4 ports detected [ 3.849984] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.863091] mmc1: Unknown controller version (3). You may experience problems. [ 3.901960] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.910105] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.922287] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.929976] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.937219] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.949404] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.974745] max77686-rtc max77620-rtc: setting system clock to 2018-02-14 16:12:09 UTC (1518624729) [ 4.182926] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.209666] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.222505] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.347320] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.407500] r8152 2-1:1.0 eth0: v1.09.9 [ 4.411548] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.423662] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.393377] r8152 2-1:1.0 eth0: carrier on [ 7.414423] IP-Config: Complete: [ 7.417646] device=eth0, hwaddr=00:04:4b:79:9d:55, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.427811] host=192.168.99.2, domain=, nis-domain=(none) [ 7.433640] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.441071] AVDD_DSI_CSI_1V2: disabling [ 7.444920] VDD_PRE_REG_1V35: disabling [ 7.448762] VDD_CAM_HV: disabling [ 7.452209] VDD_TS_HV: disabling [ 7.455567] VDD_TS_1V8: disabling [ 7.458888] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.463245] VDD_3V3_SD: disabling [ 7.466560] VDD_HDMI_5V0: disabling [ 7.470039] ALSA device list: [ 7.473003] No soundcards found. [ 7.477174] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 16:12:13 ] L4T-INITRD Build DATE: Wed Feb 14 16:12:13 UTC 2018 [ 16:12:13 ] Root device found: nfs [ 16:12:13 ] Ethernet interfaces: eth0 [ 16:12:13 ] IP Address: 192.168.99.2 [ 16:12:13 ] Rootfs mounted over nfs [ 16:12:13 ] Switching from initrd to actual rootfs [ 8.092640] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.111038] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.146111] systemd[1]: Set hostname to . [ 8.614811] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.634593] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.654656] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.674546] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 8.694595] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.718511] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.734467] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ OK ] Reached target Swap. [ OK ] Listening on Journal Socket. [ OK ] Reached target Encrypted Volumes. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. Mounting RPC Pipe File System... Starting Load Kernel Modules... Mounting POSIX Message Queue File System... Starting Remount Root and Kernel File Systems... Starting Create Static Device Nodes in /dev... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Reached target Slices. Mounting Debug File System... Mounting Huge Pages File System... [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Audit Socket. Starting Journal Service... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Journal Service. Starting udev Kernel Device Manager... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems (Pre). Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Apply Kernel Variables... Mounting Configuration File System... [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Mounted Configuration File System. [ 9.426066] systemd-journald[1573]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. Starting Create Volatile Files and Directories... [ OK ] Started Preprocess NFS configuration. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Apply Kernel Variables. Starting Raise network interfaces... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started D-Bus System Message Bus. [ 10.324538] random: crng init done Starting Permit User Sessions... Starting System Logging Service... [ OK ] Found device /dev/ttyS0. [ OK ] Started Permit User Sessions. [ OK ] Started System Logging Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting LSB: Start NTP daemon... Starting OpenBSD Secure Shell server... Starting /etc/rc.local Compatibility... [ OK ] Started Login Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Start NTP daemon. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ðò[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0xb18a4 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99076 us [0000.746] Basic modules init took 292173 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12213 us [0000.768] Carveout took 264397 us [0000.771] CPU initialization took 92765 us [0000.775] Total time taken by TegraBoot 661548 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 73 ms (4.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915459 bytes read in 209 ms (31.6 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 448 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11003/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.454662] console [ttyS0] enabled [ 0.454662] console [ttyS0] enabled [ 0.461765] bootconsole [uart0] disabled [ 0.461765] bootconsole [uart0] disabled [ 0.470269] SuperH (H)SCI(F) driver initialized [ 0.475130] msm_serial: driver initialized [ 0.479783] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.490137] loop: module loaded [ 0.494516] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.506243] max77620-sd0: supplied by regulator-dummy [ 0.512565] max77620-sd1: supplied by regulator-dummy [ 0.518716] max77620-sd2: supplied by regulator-dummy [ 0.524605] max77620-sd3: supplied by regulator-dummy [ 0.531007] max77620-ldo0: supplied by regulator-dummy [ 0.537088] max77620-ldo1: supplied by regulator-dummy [ 0.542815] max77620-ldo2: supplied by regulator-dummy [ 0.548814] max77620-ldo3: supplied by regulator-dummy [ 0.553992] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.560865] max77620-ldo4: supplied by regulator-dummy [ 0.566029] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.572599] max77620-ldo5: supplied by regulator-dummy [ 0.577762] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.584739] max77620-ldo6: supplied by regulator-dummy [ 0.589917] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.596801] max77620-ldo7: supplied by regulator-dummy [ 0.602771] max77620-ldo8: supplied by regulator-dummy [ 0.613400] libphy: Fixed MDIO Bus: probed [ 0.617792] tun: Universal TUN/TAP device driver, 1.6 [ 0.623467] thunder_xcv, ver 1.0 [ 0.626715] thunder_bgx, ver 1.0 [ 0.629972] nicpf, ver 1.0 [ 0.632938] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.638767] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.644716] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.651670] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.657267] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.665088] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.671270] sky2: driver version 1.30 [ 0.675221] usbcore: registered new interface driver r8152 [ 0.680814] VFIO - User Level meta-driver version: 0.3 [ 0.686762] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.693290] ehci-pci: EHCI PCI platform driver [ 0.697758] ehci-platform: EHCI generic platform driver [ 0.703094] ehci-orion: EHCI orion driver [ 0.707177] ehci-exynos: EHCI EXYNOS driver [ 0.711434] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.717636] ohci-pci: OHCI PCI platform driver [ 0.722111] ohci-platform: OHCI generic platform driver [ 0.727421] ohci-exynos: OHCI EXYNOS driver [ 0.732135] usbcore: registered new interface driver usb-storage [ 0.871177] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.879439] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.886600] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.892913] i2c /dev entries driver [ 0.899274] sdhci: Secure Digital Host Controller Interface driver [ 0.905451] sdhci: Copyright(c) Pierre Ossman [ 0.909965] Synopsys Designware Multimedia Card Interface Driver [ 0.916587] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.922522] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.943024] mmc0: Unknown controller version (3). You may experience problems. [ 0.981204] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.990158] ledtrig-cpu: registered to indicate activity on CPUs [ 0.997058] usbcore: registered new interface driver usbhid [ 1.002688] usbhid: USB HID core driver [ 1.008159] NET: Registered protocol family 17 [ 1.012676] 9pnet: Installing 9P2000 support [ 1.017008] Key type dns_resolver registered [ 1.021769] registered taskstats version 1 [ 1.025888] Loading compiled-in X.509 certificates [ 1.038387] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.043322] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.049112] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.054418] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.060410] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.067138] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.072334] RTL_5V: supplied by VDD_5V0_SYS [ 1.076768] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.082899] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.087845] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.100572] mmc0: new high speed MMC card at address 0001 [ 1.106532] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.111624] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.118562] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.125711] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.132078] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.138100] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.144858] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.151656] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.160978] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.167415] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.176022] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.184231] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.585743] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.994821] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.403892] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.411390] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.416885] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.425080] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.826644] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.235710] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.644768] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.652265] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.657841] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.664109] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.670289] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.677158] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.684463] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.690403] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.698443] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.707776] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.775645] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.783053] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.788465] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.797019] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.805658] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.812082] hub 1-0:1.0: USB hub found [ 3.815862] hub 1-0:1.0: 5 ports detected [ 3.820210] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.825615] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.833241] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.841631] hub 2-0:1.0: USB hub found [ 3.845408] hub 2-0:1.0: 4 ports detected [ 3.850619] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.863742] mmc1: Unknown controller version (3). You may experience problems. [ 3.902599] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.910752] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.922940] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.930620] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.937904] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.950076] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.963319] max77686-rtc max77620-rtc: setting system clock to 2018-02-14 16:13:11 UTC (1518624791) [ 4.183502] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.210220] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.222850] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.347888] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.408055] r8152 2-1:1.0 eth0: v1.09.9 [ 4.412113] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.424293] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.297978] r8152 2-1:1.0 eth0: carrier on [ 7.318996] IP-Config: Complete: [ 7.322220] device=eth0, hwaddr=00:04:4b:79:9d:55, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.332382] host=192.168.99.2, domain=, nis-domain=(none) [ 7.338211] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.345642] AVDD_DSI_CSI_1V2: disabling [ 7.349490] VDD_PRE_REG_1V35: disabling [ 7.353331] VDD_CAM_HV: disabling [ 7.356779] VDD_TS_HV: disabling [ 7.360136] VDD_TS_1V8: disabling [ 7.363458] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.367815] VDD_3V3_SD: disabling [ 7.371131] VDD_HDMI_5V0: disabling [ 7.374610] ALSA device list: [ 7.377576] No soundcards found. [ 7.381686] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 16:13:14 ] L4T-INITRD Build DATE: Wed Feb 14 16:13:14 UTC 2018 [ 16:13:14 ] Root device found: nfs [ 16:13:14 ] Ethernet interfaces: eth0 [ 16:13:14 ] IP Address: 192.168.99.2 [ 16:13:14 ] Rootfs mounted over nfs [ 16:13:14 ] Switching from initrd to actual rootfs [ 7.595861] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.614292] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.631924] systemd[1]: Set hostname to . [ 7.890253] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 7.907198] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 7.927125] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 7.943046] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 7.959118] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 7.979177] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.003209] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Created slice User and Session Slice. [ OK ] Listening on Journal Socket. [ OK ] Listening on Syslog Socket. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Debug File System... [ OK ] Reached target Slices. Starting Create Static Device Nodes in /dev... Starting Journal Service... Mounting RPC Pipe File System... Starting Load Kernel Modules... Mounting POSIX Message Queue File System... [ OK ] Created slice system-getty.slice. Mounting Huge Pages File System... Starting Remount Root and Kernel File Systems... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started udev Kernel Device Manager. [ 8.635398] systemd-journald[1555]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting LSB: Start NTP daemon... [ OK ] Started D-Bus System Message Bus. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting Permit User Sessions... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Login Service... [ OK ] Started Daily apt activities. [ 9.827142] random: crng init done [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ¾