Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.45 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.98 sec Percent passed so far: 100.0 Final Score: 100.0 [0031.241] Enabled early print [0031.244] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0031.249] Processing in recovery mode [0031.253] A02 Bootrom Patch rev = 63 [0031.256] Power-up reason: pmc por [0031.259] Established communication link with host [0032.224] Odmdata from BCT: 0x00084000 [0032.227] DebugPort= 0x3 [0032.230] BoardId read from EEPROM/NCT: 2180 [0032.258] Turned on fan for loki board [0032.261] Key release before reqd. time for fastboot [0032.266] No Battery Present [0032.269] RamCode = 0 [0032.271] Platform has Ddr4 type ram [0032.275] max77620 disabling SD1 Remote Sense [0032.279] Setting Ddr voltage to 1125mv [0032.283] Serial Number of Pmic Max77663: 0x2100a3 [0032.290] Entering ramdump check [0032.293] Get RamDumpCarveOut = 0x0 [0032.297] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0032.302] Last reboot was clean, booting normally! [0032.306] Sdram initialization is successful [0032.311] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0032.316] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0032.321] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0032.326] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0032.332] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0032.337] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0032.342] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0032.347] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0032.363] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0032.368] Platform-DebugCarveout: 0 [0032.371] Downloaded Bct successfully [0032.466] Downloaded bootloader successfully at 0x92c00000 [0032.559] Downloaded rp1 successfully at 0x83000000 [0032.608] MAX77620_GPIO1 Configured. [0032.612] MAX77620_GPIO5 Configured. [0032.615] CPU power rail is up [0032.618] CPU clock enabled [0032.622] Performing RAM repair [0032.625] Updating A64 Warmreset Address to 0x92c002e9 [0032.631] Enable APE clock/reset [0032.634] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0032.639] Loading Secure OS image failed. [0032.642] Set NvDecSticky Bits [0032.646] GSC1 address : ff700000 [0032.649] GSC2 address ff63fffc value c0edbbcc [0032.654] GSC2 address : ff600000 [0032.658] GSC3 address : ff500000 [0032.661] GSC4 address : ff400000 [0032.665] GSC5 address : ff300000 [0032.668] GSC MC Settings done [0032.671] NvTbootPackSdramParams: start. [0032.676] NvTbootPackSdramParams: done. [0032.680] Next binary entry address: 0x92c00258 [0032.685] BoardId: 2180 [0032.687] dram memory type is 3 [0032.690] Tegraboot started after 31991305 us [0032.695] Basic modules init took -31991305 us [0032.699] USB data transfer took 0 us [0032.702] Carveout took 33471905 us [0032.706] CPU initialization took 3630 us [0032.710] Total time taken by TegraBoot 1484230 us [0032.714] Starting CPU & Halting co-processor [0033.509] [0033.510] Debug Init done [0033.512] Marked DTB cacheable [0033.515] Bootloader DTB loaded at 0x83000000 [0033.520] DeviceTree Init done [0033.534] Pinmux applied successfully [0033.539] gicd_base: 0x50041000 [0033.543] gicc_base: 0x50042000 [0033.546] Interrupts Init done [0033.550] Using base:0x60005008 & irq:33 for tick-timer [0033.555] Using base:0x60005000 for delay-timer [0033.560] platform_init_timer: DONE [0033.563] Timer(tick) Init done [0033.568] osc freq = 38400 khz [0033.572] [0033.573] welcome to cboot [0033.576] [0033.577] Cboot Version: 24.00.2015.42-t210-63d15635 [0033.582] calling constructors [0033.585] initializing heap [0033.588] initializing threads [0033.590] initializing timers [0033.593] creating bootstrap completion thread [0033.598] top of bootstrap2() [0033.601] CPU: ARM Cortex A57 [0033.603] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0033.608] initializing platform [0033.645] config for ddr50 mode completed [0033.649] sdmmc bdev is already initialized [0033.653] of_register: registering tegra_udc to of_hal [0033.658] of_register: registering inv20628-driver to of_hal [0033.663] of_register: registering ads1015-driver to of_hal [0033.669] of_register: registering lp8557-bl-driver to of_hal [0033.675] of_register: registering bq2419x_charger to of_hal [0033.680] of_register: registering cpc to of_hal [0033.685] of_register: registering bq27441_fuel_gauge to of_hal [0033.699] gpio framework initialized [0033.703] of_register: registering tca9539_gpio to of_hal [0033.708] of_register: registering tca9539_gpio to of_hal [0033.713] of_register: registering i2c_bus_driver to of_hal [0033.719] of_register: registering i2c_bus_driver to of_hal [0033.724] of_register: registering i2c_bus_driver to of_hal [0033.730] pmic framework initialized [0033.733] of_register: registering max77620_pmic to of_hal [0033.739] regulator framework initialized [0033.743] of_register: registering tps65132_bl_driver to of_hal [0033.749] of_register: registering tegra_xhci to of_hal [0033.754] initializing target [0033.761] gpio_driver_register: register 'tegra_gpio_driver' driver [0033.770] fixed regulator driver initialized [0033.835] initializing OF layer [0033.840] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0033.848] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0033.869] I2C Bus Init done [0033.872] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0033.884] I2C Bus Init done [0033.887] of_children_init: Ops found for compatible string ti,lp8557 [0033.893] I2C slave not started [0033.896] I2C write failed [0033.899] Writing offset failed [0033.902] failed to read 0x 0 [0033.905] lp8557: Couldn't turn off backlight: -3 [0033.909] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0033.923] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0033.929] gpio_driver_register: register 'tca9539_gpio_driver' driver [0033.935] of_children_init: Ops found for compatible string ti,tca9539 [0033.946] tca9539_init: i2c bus: 2, slave addr: 0xee [0033.952] gpio_driver_register: register 'tca9539_gpio_driver' driver [0033.958] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0033.970] I2C Bus Init done [0033.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0033.985] I2C Bus Init done [0033.988] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.000] I2C Bus Init done [0034.002] of_children_init: Ops found for compatible string maxim,max77620 [0034.015] max77620_init using irq 118 [0034.019] register 'maxim,max77620' pmic [0034.024] gpio_driver_register: register 'max77620-gpio' driver [0034.030] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.042] I2C Bus Init done [0034.045] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0034.054] calling apps_init() [0034.060] Found 30 GPT partitions in "sdmmc3_user" [0034.065] Proceeding to flashing Server [0034.068] usbdcd_reinit Initialize driver to use already enumerated device [0034.075] nv3p_priv_usbf_open USB configuration success [0034.082] Writing GPT partition [0034.086] Erasing Boot device [0034.111] Erasing Storage Device [0035.006] Sanitizing Storage Device [0035.168] Writing protective mbr [0035.172] Writing primary GPT [0035.178] Writing secondary GPT [0035.183] Found 18 GPT partitions in "sdmmc3_user" [0035.189] Writing NVC partition [0035.192] bct_init bctinit [0035.195] bct_init bctinit [0035.203] bct_init bctinit [0035.205] bct_init bctinit [0035.208] bct_init bctinit [0035.242] partition NVC write successful. [0035.247] Writing APP partition [0035.250] bct_init bctinit [0036.089] bct_init bctinit [0036.091] bct_init bctinit [0036.696] partition APP write successful. [0036.701] Writing TBC partition [0036.704] bct_init bctinit [0036.709] bct_init bctinit [0036.712] bct_init bctinit [0036.717] partition TBC write successful. [0036.722] Writing EBT partition [0036.725] bct_init bctinit [0036.744] bct_init bctinit [0036.746] bct_init bctinit [0036.757] partition EBT write successful. [0036.762] Writing BPF partition [0036.765] bct_init bctinit [0036.790] bct_init bctinit [0036.793] bct_init bctinit [0036.798] partition BPF write successful. [0036.802] Writing WB0 partition [0036.805] bct_init bctinit [0036.809] bct_init bctinit [0036.811] bct_init bctinit [0036.816] partition WB0 write successful. [0036.820] Writing RP1 partition [0036.823] bct_init bctinit [0036.839] bct_init bctinit [0036.842] bct_init bctinit [0036.853] partition RP1 write successful. [0036.858] Writing TOS partition [0036.861] bct_init bctinit [0036.866] bct_init bctinit [0036.868] bct_init bctinit [0036.874] partition TOS write successful. [0036.879] Writing DTB partition [0036.882] bct_init bctinit [0036.897] bct_init bctinit [0036.900] bct_init bctinit [0036.909] partition DTB write successful. [0036.917] Writing BCT partition [0036.921] bct_init bctinit [0037.018] partition BCT write successful. [0037.025] Change state to cold boot mode [0037.029] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0x2100a3 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132087 us [0000.779] Basic modules init took 292474 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12209 us [0000.800] Carveout took 264397 us [0000.803] CPU initialization took 92754 us [0000.807] Total time taken by TegraBoot 661834 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2 [0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x2100a3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99042 us [0000.746] Basic modules init took 292228 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12209 us [0000.768] Carveout took 264393 us [0000.771] CPU initialization took 92753 us [0000.775] Total time taken by TegraBoot 661583 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915540 bytes read in 216 ms (30.5 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 447 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3550/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 52 ms (989.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.442170] console [ttyS0] enabled [ 0.442170] console [ttyS0] enabled [ 0.449540] bootconsole [uart0] disabled [ 0.449540] bootconsole [uart0] disabled [ 0.458057] SuperH (H)SCI(F) driver initialized [ 0.463016] msm_serial: driver initialized [ 0.467639] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.478028] loop: module loaded [ 0.482396] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.494108] max77620-sd0: supplied by regulator-dummy [ 0.500428] max77620-sd1: supplied by regulator-dummy [ 0.506581] max77620-sd2: supplied by regulator-dummy [ 0.512466] max77620-sd3: supplied by regulator-dummy [ 0.518864] max77620-ldo0: supplied by regulator-dummy [ 0.524935] max77620-ldo1: supplied by regulator-dummy [ 0.530661] max77620-ldo2: supplied by regulator-dummy [ 0.536660] max77620-ldo3: supplied by regulator-dummy [ 0.541815] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.548703] max77620-ldo4: supplied by regulator-dummy [ 0.553860] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.560427] max77620-ldo5: supplied by regulator-dummy [ 0.565581] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.572561] max77620-ldo6: supplied by regulator-dummy [ 0.577715] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.584619] max77620-ldo7: supplied by regulator-dummy [ 0.590588] max77620-ldo8: supplied by regulator-dummy [ 0.601107] libphy: Fixed MDIO Bus: probed [ 0.605583] tun: Universal TUN/TAP device driver, 1.6 [ 0.611243] thunder_xcv, ver 1.0 [ 0.614505] thunder_bgx, ver 1.0 [ 0.617752] nicpf, ver 1.0 [ 0.620705] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.626536] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.632485] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.639441] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.645039] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.652861] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.659040] sky2: driver version 1.30 [ 0.662989] usbcore: registered new interface driver r8152 [ 0.668573] VFIO - User Level meta-driver version: 0.3 [ 0.674531] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.681056] ehci-pci: EHCI PCI platform driver [ 0.685523] ehci-platform: EHCI generic platform driver [ 0.690841] ehci-orion: EHCI orion driver [ 0.694922] ehci-exynos: EHCI EXYNOS driver [ 0.699177] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.705361] ohci-pci: OHCI PCI platform driver [ 0.709833] ohci-platform: OHCI generic platform driver [ 0.715140] ohci-exynos: OHCI EXYNOS driver [ 0.719847] usbcore: registered new interface driver usb-storage [ 0.858701] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.866928] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.874102] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.880410] i2c /dev entries driver [ 0.886713] sdhci: Secure Digital Host Controller Interface driver [ 0.892894] sdhci: Copyright(c) Pierre Ossman [ 0.897401] Synopsys Designware Multimedia Card Interface Driver [ 0.904019] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.909950] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.929931] mmc0: Unknown controller version (3). You may experience problems. [ 0.968190] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.977120] ledtrig-cpu: registered to indicate activity on CPUs [ 0.983966] usbcore: registered new interface driver usbhid [ 0.989595] usbhid: USB HID core driver [ 0.995075] NET: Registered protocol family 17 [ 0.999601] 9pnet: Installing 9P2000 support [ 1.003937] Key type dns_resolver registered [ 1.008673] registered taskstats version 1 [ 1.012839] Loading compiled-in X.509 certificates [ 1.025284] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.030230] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.036024] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.041320] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.047280] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.054003] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.059195] RTL_5V: supplied by VDD_5V0_SYS [ 1.063613] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.069741] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.074674] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.087406] mmc0: new high speed MMC card at address 0001 [ 1.093383] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.098439] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.105380] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.112534] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.118907] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.124923] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.131687] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.138486] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.147821] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.154262] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.162850] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.171057] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.572587] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.981662] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.390726] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.398224] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.403720] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.411912] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.813463] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.222518] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.631569] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.639064] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.644637] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.650905] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.657083] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.663952] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.671257] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.677190] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.685212] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.694546] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.762554] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.769956] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.775365] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.783911] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.792549] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.798971] hub 1-0:1.0: USB hub found [ 3.802750] hub 1-0:1.0: 5 ports detected [ 3.807095] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.812498] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.820116] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.828498] hub 2-0:1.0: USB hub found [ 3.832270] hub 2-0:1.0: 4 ports detected [ 3.837410] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.850501] mmc1: Unknown controller version (3). You may experience problems. [ 3.889347] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.897490] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.909648] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.917330] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.924293] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.936519] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.954231] max77686-rtc max77620-rtc: setting system clock to 2018-02-08 03:27:57 UTC (1518060477) [ 4.174410] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.201106] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.213750] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.338797] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.398960] r8152 2-1:1.0 eth0: v1.09.9 [ 4.403014] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.415129] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.300878] r8152 2-1:1.0 eth0: carrier on [ 7.329906] IP-Config: Complete: [ 7.333131] device=eth0, hwaddr=00:04:4b:79:97:25, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.343296] host=192.168.99.2, domain=, nis-domain=(none) [ 7.349125] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.356540] AVDD_DSI_CSI_1V2: disabling [ 7.360388] VDD_PRE_REG_1V35: disabling [ 7.364227] VDD_CAM_HV: disabling [ 7.367674] VDD_TS_HV: disabling [ 7.371031] VDD_TS_1V8: disabling [ 7.374352] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.378710] VDD_3V3_SD: disabling [ 7.382024] VDD_HDMI_5V0: disabling [ 7.385503] ALSA device list: [ 7.388467] No soundcards found. [ 7.392574] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 03:28:00 ] L4T-INITRD Build DATE: Thu Feb 8 03:28:00 UTC 2018 [ 03:28:00 ] Root device found: nfs [ 03:28:00 ] Ethernet interfaces: eth0 [ 03:28:00 ] IP Address: 192.168.99.2 [ 03:28:00 ] Rootfs mounted over nfs [ 03:28:00 ] Switching from initrd to actual rootfs [ 8.076183] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.094565] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.265663] systemd[1]: Set hostname to . [ 9.131287] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 9.149999] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.166086] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.224814] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 9.247035] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 9.262137] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 9.282156] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on Journal Audit Socket. Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Syslog Socket. Mounting RPC Pipe File System... [ OK ] Listening on udev Kernel Socket. [ OK ] Created slice system-getty.slice. [ OK ] Reached target Encrypted Volumes. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. Starting Create Static Device Nodes in /dev... Mounting Huge Pages File System... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Mounting Configuration File System... [ OK ] Started Journal Service. [ OK ] Mounted Configuration File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Flush Journal to Persistent Storage... [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ 9.917884] systemd-journald[1566]: Received request to flush runtime journal from PID 1 Starting Raise network interfaces... [ OK ] Started Preprocess NFS configuration. [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Found device /dev/ttyS0. [ OK ] Started Update UTMP about System Boot/Shutdown. [ 10.636215] random: crng init done [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. [ OK ] Started Regular background program processing daemon. Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting OpenBSD Secure Shell server... Starting Login Service... Starting Permit User Sessions... Starting System Logging Service... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Login Service. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started System Logging Service. [ OK ] Started LSB: Start NTP daemon. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: [0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x2100a3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99041 us [0000.746] Basic modules init took 292228 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12211 us [0000.768] Carveout took 264392 us [0000.771] CPU initialization took 92753 us [0000.775] Total time taken by TegraBoot 661584 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915540 bytes read in 216 ms (30.5 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 447 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3550/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.442639] console [ttyS0] enabled [ 0.442639] console [ttyS0] enabled [ 0.449749] bootconsole [uart0] disabled [ 0.449749] bootconsole [uart0] disabled [ 0.458334] SuperH (H)SCI(F) driver initialized [ 0.463218] msm_serial: driver initialized [ 0.467809] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.478232] loop: module loaded [ 0.482577] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.494299] max77620-sd0: supplied by regulator-dummy [ 0.500619] max77620-sd1: supplied by regulator-dummy [ 0.506749] max77620-sd2: supplied by regulator-dummy [ 0.512650] max77620-sd3: supplied by regulator-dummy [ 0.519043] max77620-ldo0: supplied by regulator-dummy [ 0.525101] max77620-ldo1: supplied by regulator-dummy [ 0.530847] max77620-ldo2: supplied by regulator-dummy [ 0.536853] max77620-ldo3: supplied by regulator-dummy [ 0.542010] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.548879] max77620-ldo4: supplied by regulator-dummy [ 0.554052] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.560621] max77620-ldo5: supplied by regulator-dummy [ 0.565775] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.572762] max77620-ldo6: supplied by regulator-dummy [ 0.577917] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.584802] max77620-ldo7: supplied by regulator-dummy [ 0.590791] max77620-ldo8: supplied by regulator-dummy [ 0.601350] libphy: Fixed MDIO Bus: probed [ 0.605848] tun: Universal TUN/TAP device driver, 1.6 [ 0.611510] thunder_xcv, ver 1.0 [ 0.614775] thunder_bgx, ver 1.0 [ 0.618033] nicpf, ver 1.0 [ 0.620988] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.626819] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.632763] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.639718] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.645318] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.653140] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.659304] sky2: driver version 1.30 [ 0.663252] usbcore: registered new interface driver r8152 [ 0.668839] VFIO - User Level meta-driver version: 0.3 [ 0.674762] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.681289] ehci-pci: EHCI PCI platform driver [ 0.685760] ehci-platform: EHCI generic platform driver [ 0.691076] ehci-orion: EHCI orion driver [ 0.695157] ehci-exynos: EHCI EXYNOS driver [ 0.699412] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.705595] ohci-pci: OHCI PCI platform driver [ 0.710061] ohci-platform: OHCI generic platform driver [ 0.715365] ohci-exynos: OHCI EXYNOS driver [ 0.720060] usbcore: registered new interface driver usb-storage [ 0.859097] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.867320] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.874492] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.880799] i2c /dev entries driver [ 0.887111] sdhci: Secure Digital Host Controller Interface driver [ 0.893289] sdhci: Copyright(c) Pierre Ossman [ 0.897799] Synopsys Designware Multimedia Card Interface Driver [ 0.904413] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.910325] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.929900] mmc0: Unknown controller version (3). You may experience problems. [ 0.968163] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.977091] ledtrig-cpu: registered to indicate activity on CPUs [ 0.983903] usbcore: registered new interface driver usbhid [ 0.989526] usbhid: USB HID core driver [ 0.995018] NET: Registered protocol family 17 [ 0.999540] 9pnet: Installing 9P2000 support [ 1.003870] Key type dns_resolver registered [ 1.008672] registered taskstats version 1 [ 1.012797] Loading compiled-in X.509 certificates [ 1.024935] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.029881] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.035685] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.040993] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.046929] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.053629] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.054824] mmc0: new high speed MMC card at address 0001 [ 1.058820] RTL_5V: supplied by VDD_5V0_SYS [ 1.064209] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.068114] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.072808] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.078516] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.083429] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.087938] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.093700] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.106621] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.114041] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.119309] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.133585] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.140338] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.148699] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.155486] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.163692] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.565246] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.974309] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.383378] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.390875] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.396367] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.404558] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.806119] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.215178] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.624237] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.631730] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.637298] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.643568] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.649747] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.656616] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.663921] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.669791] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.677936] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.687268] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.754523] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.761925] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.767334] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.775881] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.784516] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.790924] hub 1-0:1.0: USB hub found [ 3.794702] hub 1-0:1.0: 5 ports detected [ 3.799051] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.804456] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.812081] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.820484] hub 2-0:1.0: USB hub found [ 3.824260] hub 2-0:1.0: 4 ports detected [ 3.829413] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.842526] mmc1: Unknown controller version (3). You may experience problems. [ 3.881388] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.889531] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.901692] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.909364] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.916478] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.928605] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.946204] max77686-rtc max77620-rtc: setting system clock to 2018-02-08 03:28:59 UTC (1518060539) [ 4.166378] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.193037] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.205275] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.338768] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.398945] r8152 2-1:1.0 eth0: v1.09.9 [ 4.402995] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.415119] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.356858] r8152 2-1:1.0 eth0: carrier on [ 7.377878] IP-Config: Complete: [ 7.381101] device=eth0, hwaddr=00:04:4b:79:97:25, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.391265] host=192.168.99.2, domain=, nis-domain=(none) [ 7.397095] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.404518] AVDD_DSI_CSI_1V2: disabling [ 7.408367] VDD_PRE_REG_1V35: disabling [ 7.412208] VDD_CAM_HV: disabling [ 7.415654] VDD_TS_HV: disabling [ 7.419013] VDD_TS_1V8: disabling [ 7.422335] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.426692] VDD_3V3_SD: disabling [ 7.430007] VDD_HDMI_5V0: disabling [ 7.433486] ALSA device list: [ 7.436452] No soundcards found. [ 7.440622] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 03:29:03 ] L4T-INITRD Build DATE: Thu Feb 8 03:29:03 UTC 2018 [ 03:29:03 ] Root device found: nfs [ 03:29:03 ] Ethernet interfaces: eth0 [ 03:29:03 ] IP Address: 192.168.99.2 [ 03:29:03 ] Rootfs mounted over nfs [ 03:29:03 ] Switching from initrd to actual rootfs [ 7.660841] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.679198] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.698792] systemd[1]: Set hostname to . [ 7.956653] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 7.974138] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 7.990009] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.006057] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.026195] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 8.042033] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.059249] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... Mounting RPC Pipe File System... Mounting Debug File System... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ OK ] Listening on udev Control Socket. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Load Kernel Modules... Mounting Huge Pages File System... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Slices. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... Mounting POSIX Message Queue File System... Starting Create Static Device Nodes in /dev... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Reached target Local File Systems (Pre). Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting udev Coldplug all Devices... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ 8.715810] systemd-journald[1562]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Found device /dev/ttyS0. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... Starting System Logging Service... Starting /etc/rc.local Compatibility... Starting Login Service... [ OK ] Started D-Bus System Message Bus. Starting Permit User Sessions... Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ 9.927735] random: crng init done [ OK ] Started Regular background program processing daemon. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Login Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: