Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.37 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.97 sec Percent passed so far: 100.0 Final Score: 100.0 þ[0022.192] Enabled early print [0022.195] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0022.200] Processing in recovery mode [0022.204] A02 Bootrom Patch rev = 63 [0022.207] Power-up reason: pmc por [0022.210] Established communication link with host [0023.175] Odmdata from BCT: 0x00084000 [0023.178] DebugPort= 0x3 [0023.181] BoardId read from EEPROM/NCT: 2180 [0023.209] Turned on fan for loki board [0023.212] Key release before reqd. time for fastboot [0023.217] No Battery Present [0023.220] RamCode = 0 [0023.222] Platform has Ddr4 type ram [0023.225] max77620 disabling SD1 Remote Sense [0023.230] Setting Ddr voltage to 1125mv [0023.234] Serial Number of Pmic Max77663: 0x405f3 [0023.241] Entering ramdump check [0023.244] Get RamDumpCarveOut = 0x0 [0023.247] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0023.253] Last reboot was clean, booting normally! [0023.257] Sdram initialization is successful [0023.261] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0023.267] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0023.272] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0023.277] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0023.282] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0023.288] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0023.293] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0023.298] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0023.313] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0023.319] Platform-DebugCarveout: 0 [0023.322] Downloaded Bct successfully [0023.416] Downloaded bootloader successfully at 0x92c00000 [0023.509] Downloaded rp1 successfully at 0x83000000 [0023.558] MAX77620_GPIO1 Configured. [0023.562] MAX77620_GPIO5 Configured. [0023.565] CPU power rail is up [0023.568] CPU clock enabled [0023.572] Performing RAM repair [0023.575] Updating A64 Warmreset Address to 0x92c002e9 [0023.581] Enable APE clock/reset [0023.584] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0023.589] Loading Secure OS image failed. [0023.593] Set NvDecSticky Bits [0023.596] GSC1 address : ff700000 [0023.600] GSC2 address ff63fffc value c0edbbcc [0023.604] GSC2 address : ff600000 [0023.608] GSC3 address : ff500000 [0023.612] GSC4 address : ff400000 [0023.616] GSC5 address : ff300000 [0023.619] GSC MC Settings done [0023.622] NvTbootPackSdramParams: start. [0023.627] NvTbootPackSdramParams: done. [0023.630] Next binary entry address: 0x92c00258 [0023.635] BoardId: 2180 [0023.638] dram memory type is 3 [0023.641] Tegraboot started after 22725095 us [0023.645] Basic modules init took -22725095 us [0023.649] USB data transfer took 0 us [0023.653] Carveout took 24204996 us [0023.656] CPU initialization took 3628 us [0023.660] Total time taken by TegraBoot 1483529 us [0023.665] Starting CPU & Halting co-processor [0024.242] [0024.243] Debug Init done [0024.245] Marked DTB cacheable [0024.248] Bootloader DTB loaded at 0x83000000 [0024.253] DeviceTree Init done [0024.267] Pinmux applied successfully [0024.272] gicd_base: 0x50041000 [0024.276] gicc_base: 0x50042000 [0024.279] Interrupts Init done [0024.283] Using base:0x60005008 & irq:33 for tick-timer [0024.288] Using base:0x60005000 for delay-timer [0024.293] platform_init_timer: DONE [0024.296] Timer(tick) Init done [0024.301] osc freq = 38400 khz [0024.305] [0024.306] welcome to cboot [0024.309] [0024.310] Cboot Version: 24.00.2015.42-t210-63d15635 [0024.315] calling constructors [0024.318] initializing heap [0024.321] initializing threads [0024.324] initializing timers [0024.326] creating bootstrap completion thread [0024.331] top of bootstrap2() [0024.334] CPU: ARM Cortex A57 [0024.337] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0024.341] initializing platform [0024.378] config for ddr50 mode completed [0024.382] sdmmc bdev is already initialized [0024.386] of_register: registering tegra_udc to of_hal [0024.391] of_register: registering inv20628-driver to of_hal [0024.396] of_register: registering ads1015-driver to of_hal [0024.402] of_register: registering lp8557-bl-driver to of_hal [0024.408] of_register: registering bq2419x_charger to of_hal [0024.413] of_register: registering cpc to of_hal [0024.418] of_register: registering bq27441_fuel_gauge to of_hal [0024.432] gpio framework initialized [0024.436] of_register: registering tca9539_gpio to of_hal [0024.441] of_register: registering tca9539_gpio to of_hal [0024.446] of_register: registering i2c_bus_driver to of_hal [0024.452] of_register: registering i2c_bus_driver to of_hal [0024.458] of_register: registering i2c_bus_driver to of_hal [0024.463] pmic framework initialized [0024.467] of_register: registering max77620_pmic to of_hal [0024.472] regulator framework initialized [0024.476] of_register: registering tps65132_bl_driver to of_hal [0024.482] of_register: registering tegra_xhci to of_hal [0024.487] initializing target [0024.494] gpio_driver_register: register 'tegra_gpio_driver' driver [0024.504] fixed regulator driver initialized [0024.568] initializing OF layer [0024.573] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0024.581] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0024.602] I2C Bus Init done [0024.605] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0024.617] I2C Bus Init done [0024.620] of_children_init: Ops found for compatible string ti,lp8557 [0024.626] I2C slave not started [0024.629] I2C write failed [0024.632] Writing offset failed [0024.635] failed to read 0x 0 [0024.638] lp8557: Couldn't turn off backlight: -3 [0024.642] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0024.656] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0024.662] gpio_driver_register: register 'tca9539_gpio_driver' driver [0024.668] of_children_init: Ops found for compatible string ti,tca9539 [0024.679] tca9539_init: i2c bus: 2, slave addr: 0xee [0024.685] gpio_driver_register: register 'tca9539_gpio_driver' driver [0024.691] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0024.703] I2C Bus Init done [0024.706] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0024.718] I2C Bus Init done [0024.721] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0024.733] I2C Bus Init done [0024.735] of_children_init: Ops found for compatible string maxim,max77620 [0024.747] max77620_init using irq 118 [0024.752] register 'maxim,max77620' pmic [0024.757] gpio_driver_register: register 'max77620-gpio' driver [0024.763] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0024.775] I2C Bus Init done [0024.778] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0024.787] calling apps_init() [0024.793] Found 30 GPT partitions in "sdmmc3_user" [0024.797] Proceeding to flashing Server [0024.801] usbdcd_reinit Initialize driver to use already enumerated device [0024.808] nv3p_priv_usbf_open USB configuration success [0024.815] Writing GPT partition [0024.819] Erasing Boot device [0024.844] Erasing Storage Device [0025.623] Sanitizing Storage Device [0025.776] Writing protective mbr [0025.780] Writing primary GPT [0025.785] Writing secondary GPT [0025.791] Found 18 GPT partitions in "sdmmc3_user" [0025.797] Writing NVC partition [0025.800] bct_init bctinit [0025.802] bct_init bctinit [0025.810] bct_init bctinit [0025.813] bct_init bctinit [0025.815] bct_init bctinit [0025.849] partition NVC write successful. [0025.853] Writing APP partition [0025.856] bct_init bctinit [0026.703] bct_init bctinit [0026.706] bct_init bctinit [0027.319] partition APP write successful. [0027.324] Writing TBC partition [0027.327] bct_init bctinit [0027.332] bct_init bctinit [0027.335] bct_init bctinit [0027.340] partition TBC write successful. [0027.345] Writing EBT partition [0027.348] bct_init bctinit [0027.366] bct_init bctinit [0027.369] bct_init bctinit [0027.379] partition EBT write successful. [0027.384] Writing BPF partition [0027.387] bct_init bctinit [0027.392] bct_init bctinit [0027.395] bct_init bctinit [0027.400] partition BPF write successful. [0027.404] Writing WB0 partition [0027.407] bct_init bctinit [0027.411] bct_init bctinit [0027.413] bct_init bctinit [0027.418] partition WB0 write successful. [0027.422] Writing RP1 partition [0027.425] bct_init bctinit [0027.441] bct_init bctinit [0027.443] bct_init bctinit [0027.453] partition RP1 write successful. [0027.457] Writing TOS partition [0027.460] bct_init bctinit [0027.466] bct_init bctinit [0027.468] bct_init bctinit [0027.474] partition TOS write successful. [0027.479] Writing DTB partition [0027.482] bct_init bctinit [0027.497] bct_init bctinit [0027.500] bct_init bctinit [0027.511] partition DTB write successful. [0027.518] Writing BCT partition [0027.522] bct_init bctinit [0027.619] partition BCT write successful. [0027.627] Change state to cold boot mode [0027.630] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0x405f3 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.447] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.673] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.723] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132083 us [0000.779] Basic modules init took 292382 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.788] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12208 us [0000.800] Carveout took 264387 us [0000.803] CPU initialization took 92739 us [0000.807] Total time taken by TegraBoot 661716 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.986] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.121] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.140] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 ¨þ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x405f3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.713] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.738] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99040 us [0000.746] Basic modules init took 292131 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12208 us [0000.767] Carveout took 264381 us [0000.771] CPU initialization took 92740 us [0000.774] Total time taken by TegraBoot 661460 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.044] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.082] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915339 bytes read in 216 ms (30.5 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 447 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11035/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.443496] console [ttyS0] enabled [ 0.443496] console [ttyS0] enabled [ 0.450591] bootconsole [uart0] disabled [ 0.450591] bootconsole [uart0] disabled [ 0.459076] SuperH (H)SCI(F) driver initialized [ 0.463916] msm_serial: driver initialized [ 0.468591] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.478987] loop: module loaded [ 0.483360] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.495070] max77620-sd0: supplied by regulator-dummy [ 0.501388] max77620-sd1: supplied by regulator-dummy [ 0.507537] max77620-sd2: supplied by regulator-dummy [ 0.513433] max77620-sd3: supplied by regulator-dummy [ 0.519830] max77620-ldo0: supplied by regulator-dummy [ 0.525900] max77620-ldo1: supplied by regulator-dummy [ 0.531623] max77620-ldo2: supplied by regulator-dummy [ 0.537623] max77620-ldo3: supplied by regulator-dummy [ 0.542779] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.549670] max77620-ldo4: supplied by regulator-dummy [ 0.554826] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.561398] max77620-ldo5: supplied by regulator-dummy [ 0.566553] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.573532] max77620-ldo6: supplied by regulator-dummy [ 0.578688] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.585582] max77620-ldo7: supplied by regulator-dummy [ 0.591545] max77620-ldo8: supplied by regulator-dummy [ 0.602149] libphy: Fixed MDIO Bus: probed [ 0.606598] tun: Universal TUN/TAP device driver, 1.6 [ 0.612255] thunder_xcv, ver 1.0 [ 0.615519] thunder_bgx, ver 1.0 [ 0.618772] nicpf, ver 1.0 [ 0.621713] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.627546] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.633489] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.640446] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.646041] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.653866] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.660040] sky2: driver version 1.30 [ 0.664002] usbcore: registered new interface driver r8152 [ 0.669590] VFIO - User Level meta-driver version: 0.3 [ 0.675525] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.682051] ehci-pci: EHCI PCI platform driver [ 0.686519] ehci-platform: EHCI generic platform driver [ 0.691832] ehci-orion: EHCI orion driver [ 0.695913] ehci-exynos: EHCI EXYNOS driver [ 0.700173] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.706358] ohci-pci: OHCI PCI platform driver [ 0.710826] ohci-platform: OHCI generic platform driver [ 0.716132] ohci-exynos: OHCI EXYNOS driver [ 0.720853] usbcore: registered new interface driver usb-storage [ 0.859668] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.867914] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.875089] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.881404] i2c /dev entries driver [ 0.887720] sdhci: Secure Digital Host Controller Interface driver [ 0.893903] sdhci: Copyright(c) Pierre Ossman [ 0.898415] Synopsys Designware Multimedia Card Interface Driver [ 0.905019] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.910941] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.932187] mmc0: Unknown controller version (3). You may experience problems. [ 0.970369] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.979304] ledtrig-cpu: registered to indicate activity on CPUs [ 0.986183] usbcore: registered new interface driver usbhid [ 0.991806] usbhid: USB HID core driver [ 0.997245] NET: Registered protocol family 17 [ 1.001763] 9pnet: Installing 9P2000 support [ 1.006100] Key type dns_resolver registered [ 1.010856] registered taskstats version 1 [ 1.014961] Loading compiled-in X.509 certificates [ 1.027139] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.032057] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.037813] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.043141] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.049100] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.055800] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.057464] mmc0: new high speed MMC card at address 0001 [ 1.060987] RTL_5V: supplied by VDD_5V0_SYS [ 1.066405] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.070317] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.074971] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.080656] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.085585] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.090091] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.095857] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.108766] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.116122] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.121462] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.135732] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.142489] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.150871] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.157649] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.165852] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.567346] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.976357] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.385368] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.392863] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.398355] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.406548] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.808053] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.217058] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.626064] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.633558] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.639131] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.645400] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.651579] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.658448] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.665756] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.671620] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.679724] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.689059] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.758772] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.766173] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.771583] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.780120] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.788758] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.795183] hub 1-0:1.0: USB hub found [ 3.798961] hub 1-0:1.0: 5 ports detected [ 3.803309] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.808712] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.816330] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.824714] hub 2-0:1.0: USB hub found [ 3.828486] hub 2-0:1.0: 4 ports detected [ 3.833621] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.846711] mmc1: Unknown controller version (3). You may experience problems. [ 3.885484] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.893629] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.905781] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.913463] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.920748] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.932900] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.958445] max77686-rtc max77620-rtc: setting system clock to 2018-02-07 04:27:20 UTC (1517977640) [ 4.170627] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.197385] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.210144] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.335026] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.395193] r8152 2-1:1.0 eth0: v1.09.9 [ 4.399236] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.411347] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.297074] r8152 2-1:1.0 eth0: carrier on [ 7.318142] IP-Config: Complete: [ 7.321365] device=eth0, hwaddr=00:04:4b:66:e7:58, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.331528] host=192.168.99.2, domain=, nis-domain=(none) [ 7.337356] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.344790] AVDD_DSI_CSI_1V2: disabling [ 7.348641] VDD_PRE_REG_1V35: disabling [ 7.352483] VDD_CAM_HV: disabling [ 7.355932] VDD_TS_HV: disabling [ 7.359290] VDD_TS_1V8: disabling [ 7.362611] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.366970] VDD_3V3_SD: disabling [ 7.370286] VDD_HDMI_5V0: disabling [ 7.373766] ALSA device list: [ 7.376731] No soundcards found. [ 7.380837] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 04:27:23 ] L4T-INITRD Build DATE: Wed Feb 7 04:27:23 UTC 2018 [ 04:27:23 ] Root device found: nfs [ 04:27:23 ] Ethernet interfaces: eth0 [ 04:27:23 ] IP Address: 192.168.99.2 [ 04:27:23 ] Rootfs mounted over nfs [ 04:27:23 ] Switching from initrd to actual rootfs [ 8.065882] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.084304] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.127974] systemd[1]: Set hostname to . [ 8.660288] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 8.678337] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.702265] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.718275] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.734451] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 8.750403] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.770357] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Audit Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Reached target Paths. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Listening on Journal Socket. Mounting RPC Pipe File System... Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... Starting Create Static Device Nodes in /dev... Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Debug File System... Starting Journal Service... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Apply Kernel Variables. [ OK ] Started udev Kernel Device Manager. [ 9.447972] systemd-journald[1566]: Received request to flush runtime journal from PID 1 Starting Raise network interfaces... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ 10.196306] random: crng init done [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started D-Bus System Message Bus. Starting System Logging Service... Starting Permit User Sessions... Starting /etc/rc.local Compatibility... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started System Logging Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: úþ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x405f3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.713] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.738] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99034 us [0000.746] Basic modules init took 292133 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12207 us [0000.767] Carveout took 264382 us [0000.771] CPU initialization took 92740 us [0000.774] Total time taken by TegraBoot 661462 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.044] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.082] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915339 bytes read in 216 ms (30.5 MiB/s) Retrieving file: /boot/Image 17601024 bytes read in 447 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11035/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.447314] console [ttyS0] enabled [ 0.447314] console [ttyS0] enabled [ 0.454411] bootconsole [uart0] disabled [ 0.454411] bootconsole [uart0] disabled [ 0.463104] SuperH (H)SCI(F) driver initialized [ 0.467934] msm_serial: driver initialized [ 0.472593] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.482943] loop: module loaded [ 0.487355] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.499032] max77620-sd0: supplied by regulator-dummy [ 0.505347] max77620-sd1: supplied by regulator-dummy [ 0.511493] max77620-sd2: supplied by regulator-dummy [ 0.517378] max77620-sd3: supplied by regulator-dummy [ 0.523776] max77620-ldo0: supplied by regulator-dummy [ 0.529852] max77620-ldo1: supplied by regulator-dummy [ 0.535574] max77620-ldo2: supplied by regulator-dummy [ 0.541571] max77620-ldo3: supplied by regulator-dummy [ 0.546731] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.553613] max77620-ldo4: supplied by regulator-dummy [ 0.558773] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.565342] max77620-ldo5: supplied by regulator-dummy [ 0.570500] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.577483] max77620-ldo6: supplied by regulator-dummy [ 0.582642] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.589540] max77620-ldo7: supplied by regulator-dummy [ 0.595503] max77620-ldo8: supplied by regulator-dummy [ 0.606107] libphy: Fixed MDIO Bus: probed [ 0.610578] tun: Universal TUN/TAP device driver, 1.6 [ 0.616222] thunder_xcv, ver 1.0 [ 0.619485] thunder_bgx, ver 1.0 [ 0.622743] nicpf, ver 1.0 [ 0.625693] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.631524] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.637471] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.644428] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.650027] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.657850] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.664021] sky2: driver version 1.30 [ 0.667970] usbcore: registered new interface driver r8152 [ 0.673578] VFIO - User Level meta-driver version: 0.3 [ 0.679525] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.686052] ehci-pci: EHCI PCI platform driver [ 0.690533] ehci-platform: EHCI generic platform driver [ 0.695854] ehci-orion: EHCI orion driver [ 0.699935] ehci-exynos: EHCI EXYNOS driver [ 0.704190] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.710373] ohci-pci: OHCI PCI platform driver [ 0.714845] ohci-platform: OHCI generic platform driver [ 0.720150] ohci-exynos: OHCI EXYNOS driver [ 0.724860] usbcore: registered new interface driver usb-storage [ 0.863794] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.872027] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.879191] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.885500] i2c /dev entries driver [ 0.891828] sdhci: Secure Digital Host Controller Interface driver [ 0.898006] sdhci: Copyright(c) Pierre Ossman [ 0.902517] Synopsys Designware Multimedia Card Interface Driver [ 0.909144] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.915065] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.934562] mmc0: Unknown controller version (3). You may experience problems. [ 0.972741] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.981679] ledtrig-cpu: registered to indicate activity on CPUs [ 0.988530] usbcore: registered new interface driver usbhid [ 0.994157] usbhid: USB HID core driver [ 0.999642] NET: Registered protocol family 17 [ 1.004170] 9pnet: Installing 9P2000 support [ 1.008499] Key type dns_resolver registered [ 1.013234] registered taskstats version 1 [ 1.017397] Loading compiled-in X.509 certificates [ 1.029838] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.034781] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.040576] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.045874] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.051856] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.058585] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.063782] RTL_5V: supplied by VDD_5V0_SYS [ 1.068203] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.074331] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.079267] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.091994] mmc0: new high speed MMC card at address 0001 [ 1.097959] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.102985] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.109922] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.117075] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.123437] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.129458] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.136209] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.143015] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.152339] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.158762] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.167234] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.174989] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.575976] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.984995] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.394008] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.401506] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.407003] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.415198] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.816717] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.225739] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.634739] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.642231] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.647810] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.654078] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.660257] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.667125] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.674432] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.680368] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.688414] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.697753] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.767187] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.774589] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.779998] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.788529] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.797168] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.803588] hub 1-0:1.0: USB hub found [ 3.807367] hub 1-0:1.0: 5 ports detected [ 3.811718] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.817123] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.824743] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.833122] hub 2-0:1.0: USB hub found [ 3.836898] hub 2-0:1.0: 4 ports detected [ 3.842050] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.855142] mmc1: Unknown controller version (3). You may experience problems. [ 3.893938] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.902086] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.914249] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.921923] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.929322] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.941500] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.970855] max77686-rtc max77620-rtc: setting system clock to 2018-02-07 04:28:21 UTC (1517977701) [ 4.175043] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.201758] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.214375] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.339428] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.399599] r8152 2-1:1.0 eth0: v1.09.9 [ 4.403644] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.415763] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.321479] r8152 2-1:1.0 eth0: carrier on [ 7.342538] IP-Config: Complete: [ 7.345761] device=eth0, hwaddr=00:04:4b:66:e7:58, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.355924] host=192.168.99.2, domain=, nis-domain=(none) [ 7.361754] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.369185] AVDD_DSI_CSI_1V2: disabling [ 7.373036] VDD_PRE_REG_1V35: disabling [ 7.376877] VDD_CAM_HV: disabling [ 7.380323] VDD_TS_HV: disabling [ 7.383682] VDD_TS_1V8: disabling [ 7.387003] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.391360] VDD_3V3_SD: disabling [ 7.394675] VDD_HDMI_5V0: disabling [ 7.398154] ALSA device list: [ 7.401119] No soundcards found. [ 7.405225] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 04:28:24 ] L4T-INITRD Build DATE: Wed Feb 7 04:28:24 UTC 2018 [ 04:28:24 ] Root device found: nfs [ 04:28:24 ] Ethernet interfaces: eth0 [ 04:28:24 ] IP Address: 192.168.99.2 [ 04:28:24 ] Rootfs mounted over nfs [ 04:28:24 ] Switching from initrd to actual rootfs [ 7.626014] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.644379] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.663445] systemd[1]: Set hostname to . [ 7.924257] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 7.942762] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 7.966707] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.982826] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.002698] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.022649] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.042752] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Syslog Socket. Mounting Huge Pages File System... [ OK ] Reached target Swap. [ OK ] Created slice system-getty.slice. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Create Static Device Nodes in /dev... [ OK ] Reached target Encrypted Volumes. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Mounting Debug File System... [ OK ] Reached target Paths. Starting Remount Root and Kernel File Systems... Mounting RPC Pipe File System... [ OK ] Listening on Journal Audit Socket. Starting Journal Service... [ OK ] Listening on udev Control Socket. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started udev Kernel Device Manager. [ 8.727087] systemd-journald[1566]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting LSB: Start NTP daemon... Starting System Logging Service... [ OK ] Started D-Bus System Message Bus. [ 9.818942] random: crng init done [ OK ] Started Regular background program processing daemon. Starting OpenBSD Secure Shell server... Starting /etc/rc.local Compatibility... Starting Permit User Sessions... [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ú