Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.46 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.93 sec Percent passed so far: 100.0 Final Score: 100.0 [0028.603] Enabled early print [0028.606] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0028.612] Processing in recovery mode [0028.615] A02 Bootrom Patch rev = 31 [0028.618] Power-up reason: pmc por [0028.622] Established communication link with host [0029.586] Odmdata from BCT: 0x00084000 [0029.589] DebugPort= 0x3 [0029.592] BoardId read from EEPROM/NCT: 2180 [0029.620] Turned on fan for loki board [0029.623] Key release before reqd. time for fastboot [0029.628] No Battery Present [0029.631] RamCode = 0 [0029.633] Platform has Ddr4 type ram [0029.637] max77620 disabling SD1 Remote Sense [0029.641] Setting Ddr voltage to 1125mv [0029.645] Serial Number of Pmic Max77663: 0x61088 [0029.652] Entering ramdump check [0029.655] Get RamDumpCarveOut = 0x0 [0029.659] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0029.664] Last reboot was clean, booting normally! [0029.668] Sdram initialization is successful [0029.673] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0029.678] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0029.683] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0029.688] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0029.693] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0029.699] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0029.704] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0029.709] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0029.725] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0029.730] Platform-DebugCarveout: 0 [0029.733] Downloaded Bct successfully [0029.827] Downloaded bootloader successfully at 0x92c00000 [0029.921] Downloaded rp1 successfully at 0x83000000 [0029.959] MAX77620_GPIO1 Configured. [0029.963] MAX77620_GPIO5 Configured. [0029.966] CPU power rail is up [0029.969] CPU clock enabled [0029.973] Performing RAM repair [0029.976] Updating A64 Warmreset Address to 0x92c002e9 [0029.982] Enable APE clock/reset [0029.985] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0029.990] Loading Secure OS image failed. [0029.994] Set NvDecSticky Bits [0029.997] GSC1 address : ff700000 [0030.001] GSC2 address ff63fffc value c0edbbcc [0030.005] GSC2 address : ff600000 [0030.009] GSC3 address : ff500000 [0030.013] GSC4 address : ff400000 [0030.016] GSC5 address : ff300000 [0030.020] GSC MC Settings done [0030.023] NvTbootPackSdramParams: start. [0030.028] NvTbootPackSdramParams: done. [0030.031] Next binary entry address: 0x92c00258 [0030.036] BoardId: 2180 [0030.039] dram memory type is 3 [0030.042] Tegraboot started after 29290110 us [0030.046] Basic modules init took -29290110 us [0030.050] USB data transfer took 0 us [0030.054] Carveout took 30759563 us [0030.057] CPU initialization took 3629 us [0030.061] Total time taken by TegraBoot 1473082 us [0030.066] Starting CPU & Halting co-processor [0030.796] [0030.798] Debug Init done [0030.800] Marked DTB cacheable [0030.803] Bootloader DTB loaded at 0x83000000 [0030.807] DeviceTree Init done [0030.822] Pinmux applied successfully [0030.827] gicd_base: 0x50041000 [0030.830] gicc_base: 0x50042000 [0030.833] Interrupts Init done [0030.838] Using base:0x60005008 & irq:33 for tick-timer [0030.843] Using base:0x60005000 for delay-timer [0030.847] platform_init_timer: DONE [0030.851] Timer(tick) Init done [0030.855] osc freq = 38400 khz [0030.860] [0030.861] welcome to cboot [0030.863] [0030.865] Cboot Version: 24.00.2015.42-t210-63d15635 [0030.870] calling constructors [0030.872] initializing heap [0030.875] initializing threads [0030.878] initializing timers [0030.881] creating bootstrap completion thread [0030.885] top of bootstrap2() [0030.888] CPU: ARM Cortex A57 [0030.891] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0030.896] initializing platform [0030.922] config for ddr50 mode completed [0030.926] sdmmc bdev is already initialized [0030.930] of_register: registering tegra_udc to of_hal [0030.935] of_register: registering inv20628-driver to of_hal [0030.941] of_register: registering ads1015-driver to of_hal [0030.946] of_register: registering lp8557-bl-driver to of_hal [0030.952] of_register: registering bq2419x_charger to of_hal [0030.958] of_register: registering cpc to of_hal [0030.962] of_register: registering bq27441_fuel_gauge to of_hal [0030.977] gpio framework initialized [0030.980] of_register: registering tca9539_gpio to of_hal [0030.985] of_register: registering tca9539_gpio to of_hal [0030.991] of_register: registering i2c_bus_driver to of_hal [0030.996] of_register: registering i2c_bus_driver to of_hal [0031.002] of_register: registering i2c_bus_driver to of_hal [0031.007] pmic framework initialized [0031.011] of_register: registering max77620_pmic to of_hal [0031.016] regulator framework initialized [0031.020] of_register: registering tps65132_bl_driver to of_hal [0031.026] of_register: registering tegra_xhci to of_hal [0031.031] initializing target [0031.038] gpio_driver_register: register 'tegra_gpio_driver' driver [0031.048] fixed regulator driver initialized [0031.112] initializing OF layer [0031.117] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0031.125] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0031.147] I2C Bus Init done [0031.150] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0031.161] I2C Bus Init done [0031.164] of_children_init: Ops found for compatible string ti,lp8557 [0031.171] of_children_init: Ops found for compatible string ti,tca9539 [0031.182] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0031.188] gpio_driver_register: register 'tca9539_gpio_driver' driver [0031.194] of_children_init: Ops found for compatible string ti,tca9539 [0031.205] tca9539_init: i2c bus: 2, slave addr: 0xee [0031.211] gpio_driver_register: register 'tca9539_gpio_driver' driver [0031.217] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0031.229] I2C Bus Init done [0031.232] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0031.244] I2C Bus Init done [0031.247] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0031.259] I2C Bus Init done [0031.261] of_children_init: Ops found for compatible string maxim,max77620 [0031.274] max77620_init using irq 118 [0031.279] register 'maxim,max77620' pmic [0031.283] gpio_driver_register: register 'max77620-gpio' driver [0031.289] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0031.301] I2C Bus Init done [0031.304] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0031.313] calling apps_init() [0031.319] Found 30 GPT partitions in "sdmmc3_user" [0031.324] Proceeding to flashing Server [0031.327] usbdcd_reinit Initialize driver to use already enumerated device [0031.334] nv3p_priv_usbf_open USB configuration success [0031.341] Writing GPT partition [0031.345] Erasing Boot device [0031.371] Erasing Storage Device [0032.285] Sanitizing Storage Device [0032.505] Writing protective mbr [0032.509] Writing primary GPT [0032.514] Writing secondary GPT [0032.520] Found 18 GPT partitions in "sdmmc3_user" [0032.525] Writing NVC partition [0032.528] bct_init bctinit [0032.531] bct_init bctinit [0032.539] bct_init bctinit [0032.542] bct_init bctinit [0032.545] bct_init bctinit [0032.582] partition NVC write successful. [0032.586] Writing APP partition [0032.589] bct_init bctinit [0033.424] bct_init bctinit [0033.427] bct_init bctinit [0034.061] partition APP write successful. [0034.066] Writing TBC partition [0034.069] bct_init bctinit [0034.074] bct_init bctinit [0034.076] bct_init bctinit [0034.082] partition TBC write successful. [0034.086] Writing EBT partition [0034.089] bct_init bctinit [0034.108] bct_init bctinit [0034.111] bct_init bctinit [0034.122] partition EBT write successful. [0034.126] Writing BPF partition [0034.129] bct_init bctinit [0034.134] bct_init bctinit [0034.137] bct_init bctinit [0034.142] partition BPF write successful. [0034.147] Writing WB0 partition [0034.150] bct_init bctinit [0034.153] bct_init bctinit [0034.156] bct_init bctinit [0034.160] partition WB0 write successful. [0034.164] Writing RP1 partition [0034.167] bct_init bctinit [0034.183] bct_init bctinit [0034.186] bct_init bctinit [0034.195] partition RP1 write successful. [0034.200] Writing TOS partition [0034.203] bct_init bctinit [0034.208] bct_init bctinit [0034.211] bct_init bctinit [0034.216] partition TOS write successful. [0034.221] Writing DTB partition [0034.224] bct_init bctinit [0034.240] bct_init bctinit [0034.242] bct_init bctinit [0034.254] partition DTB write successful. [0034.261] Writing BCT partition [0034.265] bct_init bctinit [0034.365] partition BCT write successful. [0034.372] Change state to cold boot mode [0034.376] Flushing data to stroage [0000.163] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.169] Processing in cold boot mode Bootloader 2 [0000.173] A02 Bootrom Patch rev = 31 [0000.177] Power-up reason: software reset [0000.180] No Battery Present [0000.183] RamCode = 0 [0000.185] Platform has Ddr4 type ram [0000.189] max77620 disabling SD1 Remote Sense [0000.193] Setting Ddr voltage to 1125mv [0000.197] Serial Number of Pmic Max77663: 0x61088 [0000.204] Entering ramdump check [0000.207] Get RamDumpCarveOut = 0x0 [0000.211] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.216] Last reboot was clean, booting normally! [0000.220] Sdram initialization is successful [0000.225] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.230] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.235] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.240] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.245] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.251] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.256] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.261] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.276] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.282] Platform-DebugCarveout: 0 [0000.285] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.290] Non secure mode. Disable rollback prevention [0000.295] AOTAG Init Done [0000.322] Using GPT Primary to query partitions [0000.328] Loading Tboot-CPU binary [0000.377] Verifying bootloader in OdmNonSecureSBK mode [0000.387] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.394] Bootloader downloaded successfully. [0000.398] Downloaded Tboot-CPU binary to 0xa0000258 [0000.403] MAX77620_GPIO1 Configured. [0000.406] MAX77620_GPIO5 Configured. [0000.410] CPU power rail is up [0000.413] CPU clock enabled [0000.416] Performing RAM repair [0000.419] Updating A64 Warmreset Address to 0xa00002e9 [0000.436] Bootloader DTB Load Address: 0x83000000 [0000.453] Kernel DTB Load Address: 0x83080000 [0000.458] Loading cboot binary [0000.552] Verifying bootloader in OdmNonSecureSBK mode [0000.657] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.664] Bootloader downloaded successfully. [0000.668] GPT: Partition NOT found ! [0000.672] Find Partition via GPT Failed [0000.676] Find Partition via PT Failed [0000.679] function NvTbootGetBinaryOffsets: 0x1 error [0000.684] Error in NvTbootLoadBinary: 0x1 ! [0000.688] Next binary entry address: 0x80110000 [0000.692] BoardId: 2180 [0000.697] dram memory type is 3 [0000.701] WB0 init successful [0000.727] Bpmp FW successfully loaded [0000.730] Set NvDecSticky Bits [0000.734] GSC1 address : ff700000 [0000.737] GSC2 address ff63fffc value c0edbbcc [0000.742] GSC2 address : ff600000 [0000.746] GSC3 address : ff500000 [0000.749] GSC4 address : ff400000 [0000.753] GSC5 address : ff300000 [0000.756] GSC MC Settings done [0000.760] TOS old plaintext Image length 65536 [0000.766] *** Secure OS image signature not verified *** [0000.771] Loading and Validation of Secure OS Successful [0000.776] NvTbootPackSdramParams: start. [0000.781] NvTbootPackSdramParams: done. [0000.785] Tegraboot started after 142688 us [0000.789] Basic modules init took 292396 us [0000.793] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.799] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.806] Next stage binary read took 12209 us [0000.810] Carveout took 264394 us [0000.814] CPU initialization took 92751 us [0000.817] Total time taken by TegraBoot 661750 us [0000.822] Starting CPU & Halting co-processor 64b[0000.930] RamCode = 0 [0000.945] LPDDR4 Training: Read DT: Number of tables = 10 [0000.950] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.955] EMC Training Skipped [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.963] EMC Training Skipped [0000.966] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.971] EMC Training Skipped [0000.974] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.979] EMC Training Skipped [0000.982] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.988] EMC Training Successful [0000.991] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.997] EMC Training Successful [0001.000] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.011] EMC Training Successful [0001.014] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.037] EMC Training Successful [0001.040] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.062] EMC Training Successful [0001.065] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.084] EMC Training Successful [0001.087] Switching to 800000 KHz Success [0001.094] DT Write: emc-table@40800 succeeded [0001.100] DT Write: emc-table@68000 succeeded [0001.106] DT Write: emc-table@102000 succeeded [0001.113] DT Write: emc-table@204000 succeeded [0001.119] DT Write: emc-table@408000 succeeded [0001.125] DT Write: emc-table@665600 succeeded [0001.132] DT Write: emc-table@800000 succeeded [0001.138] DT Write: emc-table@1065600 succeeded [0001.144] DT Write: emc-table@1331200 succeeded [0001.151] DT Write: emc-table@1600000 succeeded [0001.155] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 [0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 31 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.141] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x61088 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99349 us [0000.746] Basic modules init took 292148 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12209 us [0000.768] Carveout took 264390 us [0000.771] CPU initialization took 92752 us [0000.775] Total time taken by TegraBoot 661499 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915317 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17527296 bytes read in 446 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3619/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.447283] console [ttyS0] enabled [ 0.447283] console [ttyS0] enabled [ 0.454383] bootconsole [uart0] disabled [ 0.454383] bootconsole [uart0] disabled [ 0.463129] SuperH (H)SCI(F) driver initialized [ 0.467981] msm_serial: driver initialized [ 0.472585] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.483006] loop: module loaded [ 0.487402] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.499150] max77620-sd0: supplied by regulator-dummy [ 0.505479] max77620-sd1: supplied by regulator-dummy [ 0.511622] max77620-sd2: supplied by regulator-dummy [ 0.517511] max77620-sd3: supplied by regulator-dummy [ 0.523892] max77620-ldo0: supplied by regulator-dummy [ 0.529977] max77620-ldo1: supplied by regulator-dummy [ 0.535705] max77620-ldo2: supplied by regulator-dummy [ 0.541706] max77620-ldo3: supplied by regulator-dummy [ 0.546864] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.553756] max77620-ldo4: supplied by regulator-dummy [ 0.558916] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.565483] max77620-ldo5: supplied by regulator-dummy [ 0.570637] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.577627] max77620-ldo6: supplied by regulator-dummy [ 0.582781] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.589683] max77620-ldo7: supplied by regulator-dummy [ 0.595646] max77620-ldo8: supplied by regulator-dummy [ 0.606276] libphy: Fixed MDIO Bus: probed [ 0.610851] tun: Universal TUN/TAP device driver, 1.6 [ 0.616523] thunder_xcv, ver 1.0 [ 0.619785] thunder_bgx, ver 1.0 [ 0.623044] nicpf, ver 1.0 [ 0.626012] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.631841] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.637789] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.644743] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.650340] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.658164] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.664331] sky2: driver version 1.30 [ 0.668287] usbcore: registered new interface driver r8152 [ 0.673875] VFIO - User Level meta-driver version: 0.3 [ 0.679830] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.686358] ehci-pci: EHCI PCI platform driver [ 0.690830] ehci-platform: EHCI generic platform driver [ 0.696151] ehci-orion: EHCI orion driver [ 0.700234] ehci-exynos: EHCI EXYNOS driver [ 0.704488] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.710673] ohci-pci: OHCI PCI platform driver [ 0.715139] ohci-platform: OHCI generic platform driver [ 0.720445] ohci-exynos: OHCI EXYNOS driver [ 0.725152] usbcore: registered new interface driver usb-storage [ 0.863986] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.872214] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.879382] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.885691] i2c /dev entries driver [ 0.892006] sdhci: Secure Digital Host Controller Interface driver [ 0.898187] sdhci: Copyright(c) Pierre Ossman [ 0.902694] Synopsys Designware Multimedia Card Interface Driver [ 0.909298] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.915209] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.936464] mmc0: Unknown controller version (3). You may experience problems. [ 0.974062] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.982996] ledtrig-cpu: registered to indicate activity on CPUs [ 0.989849] usbcore: registered new interface driver usbhid [ 0.995474] usbhid: USB HID core driver [ 1.000963] NET: Registered protocol family 17 [ 1.005493] 9pnet: Installing 9P2000 support [ 1.009824] Key type dns_resolver registered [ 1.014568] registered taskstats version 1 [ 1.018745] Loading compiled-in X.509 certificates [ 1.030839] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.035771] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.041572] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.046894] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.052828] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.059555] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.064803] RTL_5V: supplied by VDD_5V0_SYS [ 1.069214] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.075295] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.080243] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.093413] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.100344] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.107123] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.113909] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.121411] mmc0: new high speed MMC card at address 0001 [ 1.122239] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.127379] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.133626] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.137356] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.145102] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.149426] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.162494] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.171463] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.558133] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.967236] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.376352] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.383848] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.389344] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.397543] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.806627] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.215722] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.624834] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.632328] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.637911] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.644178] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.650358] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.657229] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.664537] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.670503] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.678556] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.687893] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.758100] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.765507] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.770917] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.779465] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.788104] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.794540] hub 1-0:1.0: USB hub found [ 3.798322] hub 1-0:1.0: 5 ports detected [ 3.802663] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.808064] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.815686] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.824070] hub 2-0:1.0: USB hub found [ 3.827844] hub 2-0:1.0: 4 ports detected [ 3.833001] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.846094] mmc1: Unknown controller version (3). You may experience problems. [ 3.884869] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.893013] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.905169] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.912870] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.920196] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.932340] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.949759] max77686-rtc max77620-rtc: setting system clock to 2018-02-06 11:41:27 UTC (1517917287) [ 4.165955] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.192615] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.205248] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.330343] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.390503] r8152 2-1:1.0 eth0: v1.09.9 [ 4.394554] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.406690] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.328437] r8152 2-1:1.0 eth0: carrier on [ 7.353450] IP-Config: Complete: [ 7.356674] device=eth0, hwaddr=00:04:4b:56:d5:a7, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.366839] host=192.168.99.2, domain=, nis-domain=(none) [ 7.372667] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.380081] AVDD_DSI_CSI_1V2: disabling [ 7.383931] VDD_PRE_REG_1V35: disabling [ 7.387771] VDD_CAM_HV: disabling [ 7.391225] VDD_TS_HV: disabling [ 7.394580] VDD_TS_1V8: disabling [ 7.397902] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.402259] VDD_3V3_SD: disabling [ 7.405575] VDD_HDMI_5V0: disabling [ 7.409056] ALSA device list: [ 7.412022] No soundcards found. [ 7.416145] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 11:41:30 ] L4T-INITRD Build DATE: Tue Feb 6 11:41:30 UTC 2018 [ 11:41:30 ] Root device found: nfs [ 11:41:30 ] Ethernet interfaces: eth0 [ 11:41:30 ] IP Address: 192.168.99.2 [ 11:41:30 ] Rootfs mounted over nfs [ 11:41:30 ] Switching from initrd to actual rootfs [ 8.167907] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.186325] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.215060] systemd[1]: Set hostname to . [ 8.656450] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 8.677685] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.693663] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.717672] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 8.733552] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.749806] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.769689] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. Mounting POSIX Message Queue File System... [ OK ] Reached target Slices. Starting Load Kernel Modules... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. Mounting RPC Pipe File System... [ OK ] Reached target Encrypted Volumes. Mounting Huge Pages File System... Starting Create Static Device Nodes in /dev... [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Reached target Swap. [ OK ] Listening on udev Control Socket. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Debug File System... Starting Remount Root and Kernel File Systems... [ OK ] Created slice system-getty.slice. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Mounting Configuration File System... Starting Apply Kernel Variables... [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Mounted Configuration File System. [ 9.408524] systemd-journald[1559]: Received request to flush runtime journal from PID 1 [ OK ] Started Preprocess NFS configuration. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. Starting Raise network interfaces... Starting Create Volatile Files and Directories... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started udev Kernel Device Manager. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Found device /dev/ttyS0. [ OK ] Started Update UTMP about System Boot/Shutdown. [ 10.201803] random: crng init done [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Started Daily apt activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Permit User Sessions... Starting /etc/rc.local Compatibility... Starting System Logging Service... Starting LSB: Start NTP daemon... [ OK ] Started Regular background program processing daemon. Starting OpenBSD Secure Shell server... Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Started D-Bus System Message Bus. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: àÿ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 31 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.141] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x61088 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99336 us [0000.746] Basic modules init took 292164 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12210 us [0000.768] Carveout took 264391 us [0000.771] CPU initialization took 92750 us [0000.775] Total time taken by TegraBoot 661515 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915317 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17527296 bytes read in 446 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3619/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.448009] console [ttyS0] enabled [ 0.448009] console [ttyS0] enabled [ 0.455125] bootconsole [uart0] disabled [ 0.455125] bootconsole [uart0] disabled [ 0.463589] SuperH (H)SCI(F) driver initialized [ 0.468580] msm_serial: driver initialized [ 0.473187] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.484080] loop: module loaded [ 0.488433] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.500119] max77620-sd0: supplied by regulator-dummy [ 0.506397] max77620-sd1: supplied by regulator-dummy [ 0.512542] max77620-sd2: supplied by regulator-dummy [ 0.518461] max77620-sd3: supplied by regulator-dummy [ 0.524853] max77620-ldo0: supplied by regulator-dummy [ 0.530916] max77620-ldo1: supplied by regulator-dummy [ 0.536662] max77620-ldo2: supplied by regulator-dummy [ 0.542664] max77620-ldo3: supplied by regulator-dummy [ 0.547821] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.554686] max77620-ldo4: supplied by regulator-dummy [ 0.559861] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.566437] max77620-ldo5: supplied by regulator-dummy [ 0.571591] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.578572] max77620-ldo6: supplied by regulator-dummy [ 0.583728] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.590611] max77620-ldo7: supplied by regulator-dummy [ 0.596601] max77620-ldo8: supplied by regulator-dummy [ 0.607195] libphy: Fixed MDIO Bus: probed [ 0.611658] tun: Universal TUN/TAP device driver, 1.6 [ 0.617342] thunder_xcv, ver 1.0 [ 0.620607] thunder_bgx, ver 1.0 [ 0.623868] nicpf, ver 1.0 [ 0.626837] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.632666] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.638612] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.645567] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.651168] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.658989] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.665156] sky2: driver version 1.30 [ 0.669108] usbcore: registered new interface driver r8152 [ 0.674698] VFIO - User Level meta-driver version: 0.3 [ 0.680644] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.687174] ehci-pci: EHCI PCI platform driver [ 0.691645] ehci-platform: EHCI generic platform driver [ 0.696968] ehci-orion: EHCI orion driver [ 0.701049] ehci-exynos: EHCI EXYNOS driver [ 0.705303] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.711486] ohci-pci: OHCI PCI platform driver [ 0.715957] ohci-platform: OHCI generic platform driver [ 0.721262] ohci-exynos: OHCI EXYNOS driver [ 0.725992] usbcore: registered new interface driver usb-storage [ 0.864981] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.873217] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.880378] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.886689] i2c /dev entries driver [ 0.892991] sdhci: Secure Digital Host Controller Interface driver [ 0.899173] sdhci: Copyright(c) Pierre Ossman [ 0.903685] Synopsys Designware Multimedia Card Interface Driver [ 0.910287] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.916200] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.937470] mmc0: Unknown controller version (3). You may experience problems. [ 0.975744] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.984677] ledtrig-cpu: registered to indicate activity on CPUs [ 0.991562] usbcore: registered new interface driver usbhid [ 0.997186] usbhid: USB HID core driver [ 1.002682] NET: Registered protocol family 17 [ 1.007199] 9pnet: Installing 9P2000 support [ 1.011532] Key type dns_resolver registered [ 1.016266] registered taskstats version 1 [ 1.020430] Loading compiled-in X.509 certificates [ 1.032688] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.037631] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.043429] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.048726] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.054653] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.061372] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.066607] RTL_5V: supplied by VDD_5V0_SYS [ 1.071030] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.077124] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.082067] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.095264] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.102240] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.109053] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.115860] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.123360] mmc0: new high speed MMC card at address 0001 [ 1.129321] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.134330] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.140695] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.146753] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.154416] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.161397] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.168420] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.176177] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.576921] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.986078] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.395215] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.402712] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.408208] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.416404] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.818039] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.227188] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.636328] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.643822] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.649406] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.655676] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.661856] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.668726] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.676035] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.681992] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.690052] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.699390] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.770219] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777620] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.783030] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791578] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.800216] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806650] hub 1-0:1.0: USB hub found [ 3.810431] hub 1-0:1.0: 5 ports detected [ 3.814774] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.820177] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827797] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.836192] hub 2-0:1.0: USB hub found [ 3.839965] hub 2-0:1.0: 4 ports detected [ 3.845138] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.858227] mmc1: Unknown controller version (3). You may experience problems. [ 3.896999] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.905144] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.917283] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.924951] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.931975] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.944122] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.970096] max77686-rtc max77620-rtc: setting system clock to 2018-02-06 11:42:29 UTC (1517917349) [ 4.182075] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.208790] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.221426] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.346459] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.406636] r8152 2-1:1.0 eth0: v1.09.9 [ 4.410686] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.422818] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.324530] r8152 2-1:1.0 eth0: carrier on [ 7.345577] IP-Config: Complete: [ 7.348800] device=eth0, hwaddr=00:04:4b:56:d5:a7, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.358977] host=192.168.99.2, domain=, nis-domain=(none) [ 7.364806] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.372239] AVDD_DSI_CSI_1V2: disabling [ 7.376088] VDD_PRE_REG_1V35: disabling [ 7.379930] VDD_CAM_HV: disabling [ 7.383385] VDD_TS_HV: disabling [ 7.386739] VDD_TS_1V8: disabling [ 7.390087] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.394446] VDD_3V3_SD: disabling [ 7.397762] VDD_HDMI_5V0: disabling [ 7.401242] ALSA device list: [ 7.404209] No soundcards found. [ 7.408308] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 11:42:32 ] L4T-INITRD Build DATE: Tue Feb 6 11:42:32 UTC 2018 [ 11:42:32 ] Root device found: nfs [ 11:42:32 ] Ethernet interfaces: eth0 [ 11:42:32 ] IP Address: 192.168.99.2 [ 11:42:32 ] Rootfs mounted over nfs [ 11:42:32 ] Switching from initrd to actual rootfs [ 7.626340] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.644691] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.662519] systemd[1]: Set hostname to . [ 7.920245] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 7.941783] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 7.961748] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.977914] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 7.997671] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.013668] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.029790] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on udev Control Socket. [ OK ] Created slice System Slice. Mounting RPC Pipe File System... Mounting Debug File System... [ OK ] Reached target Slices. Mounting Huge Pages File System... [ OK ] Created slice system-getty.slice. Starting Create Static Device Nodes in /dev... Starting Remount Root and Kernel File Systems... [ OK ] Listening on Journal Audit Socket. [ OK ] Reached target Encrypted Volumes. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... Mounting POSIX Message Queue File System... Starting Load Kernel Modules... [ OK ] Reached target Swap. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting udev Kernel Device Manager... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started udev Kernel Device Manager. [ 8.703448] systemd-journald[1563]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started D-Bus System Message Bus. Starting LSB: Start NTP daemon... [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... Starting System Logging Service... [ OK ] Started /etc/rc.local Compatibility. [ 9.927961] random: crng init done [ OK ] Started Permit User Sessions. [ OK ] Started System Logging Service. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ¸