Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.36 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.95 sec Percent passed so far: 100.0 Final Score: 100.0 ±[0027.054] Enabled early print [0027.056] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0027.062] Processing in recovery mode [0027.065] A02 Bootrom Patch rev = 63 [0027.069] Power-up reason: pmc por [0027.072] Established communication link with host [0028.039] Odmdata from BCT: 0x00084000 [0028.043] DebugPort= 0x3 [0028.045] BoardId read from EEPROM/NCT: 2180 [0028.073] Turned on fan for loki board [0028.077] Key release before reqd. time for fastboot [0028.082] No Battery Present [0028.084] RamCode = 0 [0028.087] Platform has Ddr4 type ram [0028.090] max77620 disabling SD1 Remote Sense [0028.094] Setting Ddr voltage to 1125mv [0028.098] Serial Number of Pmic Max77663: 0xb0af8 [0028.106] Entering ramdump check [0028.109] Get RamDumpCarveOut = 0x0 [0028.112] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0028.117] Last reboot was clean, booting normally! [0028.122] Sdram initialization is successful [0028.126] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0028.132] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0028.137] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0028.142] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0028.147] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0028.152] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0028.157] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0028.163] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0028.178] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0028.183] Platform-DebugCarveout: 0 [0028.187] Downloaded Bct successfully [0028.290] Downloaded bootloader successfully at 0x92c00000 [0028.390] Downloaded rp1 successfully at 0x83000000 [0028.438] MAX77620_GPIO1 Configured. [0028.442] MAX77620_GPIO5 Configured. [0028.445] CPU power rail is up [0028.448] CPU clock enabled [0028.452] Performing RAM repair [0028.455] Updating A64 Warmreset Address to 0x92c002e9 [0028.461] Enable APE clock/reset [0028.464] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0028.468] Loading Secure OS image failed. [0028.472] Set NvDecSticky Bits [0028.476] GSC1 address : ff700000 [0028.479] GSC2 address ff63fffc value c0edbbcc [0028.484] GSC2 address : ff600000 [0028.488] GSC3 address : ff500000 [0028.491] GSC4 address : ff400000 [0028.495] GSC5 address : ff300000 [0028.498] GSC MC Settings done [0028.501] NvTbootPackSdramParams: start. [0028.506] NvTbootPackSdramParams: done. [0028.510] Next binary entry address: 0x92c00258 [0028.515] BoardId: 2180 [0028.517] dram memory type is 3 [0028.520] Tegraboot started after 27703159 us [0028.525] Basic modules init took -27703159 us [0028.529] USB data transfer took 0 us [0028.532] Carveout took 29201779 us [0028.536] CPU initialization took 3629 us [0028.540] Total time taken by TegraBoot 1502249 us [0028.544] Starting CPU & Halting co-processor [0029.239] [0029.240] Debug Init done [0029.242] Marked DTB cacheable [0029.245] Bootloader DTB loaded at 0x83000000 [0029.250] DeviceTree Init done [0029.264] Pinmux applied successfully [0029.269] gicd_base: 0x50041000 [0029.273] gicc_base: 0x50042000 [0029.276] Interrupts Init done [0029.280] Using base:0x60005008 & irq:33 for tick-timer [0029.285] Using base:0x60005000 for delay-timer [0029.290] platform_init_timer: DONE [0029.293] Timer(tick) Init done [0029.297] osc freq = 38400 khz [0029.302] [0029.303] welcome to cboot [0029.306] [0029.307] Cboot Version: 24.00.2015.42-t210-63d15635 [0029.312] calling constructors [0029.315] initializing heap [0029.317] initializing threads [0029.320] initializing timers [0029.323] creating bootstrap completion thread [0029.328] top of bootstrap2() [0029.330] CPU: ARM Cortex A57 [0029.333] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0029.338] initializing platform [0029.364] config for ddr50 mode completed [0029.368] sdmmc bdev is already initialized [0029.372] of_register: registering tegra_udc to of_hal [0029.377] of_register: registering inv20628-driver to of_hal [0029.383] of_register: registering ads1015-driver to of_hal [0029.389] of_register: registering lp8557-bl-driver to of_hal [0029.394] of_register: registering bq2419x_charger to of_hal [0029.400] of_register: registering cpc to of_hal [0029.405] of_register: registering bq27441_fuel_gauge to of_hal [0029.419] gpio framework initialized [0029.422] of_register: registering tca9539_gpio to of_hal [0029.428] of_register: registering tca9539_gpio to of_hal [0029.433] of_register: registering i2c_bus_driver to of_hal [0029.439] of_register: registering i2c_bus_driver to of_hal [0029.444] of_register: registering i2c_bus_driver to of_hal [0029.450] pmic framework initialized [0029.453] of_register: registering max77620_pmic to of_hal [0029.459] regulator framework initialized [0029.463] of_register: registering tps65132_bl_driver to of_hal [0029.468] of_register: registering tegra_xhci to of_hal [0029.474] initializing target [0029.480] gpio_driver_register: register 'tegra_gpio_driver' driver [0029.490] fixed regulator driver initialized [0029.555] initializing OF layer [0029.559] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0029.567] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.589] I2C Bus Init done [0029.592] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.604] I2C Bus Init done [0029.606] of_children_init: Ops found for compatible string ti,lp8557 [0029.613] I2C slave not started [0029.616] I2C write failed [0029.618] Writing offset failed [0029.621] failed to read 0x 0 [0029.624] lp8557: Couldn't turn off backlight: -3 [0029.629] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0029.643] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0029.648] gpio_driver_register: register 'tca9539_gpio_driver' driver [0029.655] of_children_init: Ops found for compatible string ti,tca9539 [0029.666] tca9539_init: i2c bus: 2, slave addr: 0xee [0029.671] gpio_driver_register: register 'tca9539_gpio_driver' driver [0029.678] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.690] I2C Bus Init done [0029.692] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.705] I2C Bus Init done [0029.707] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.719] I2C Bus Init done [0029.722] of_children_init: Ops found for compatible string maxim,max77620 [0029.734] max77620_init using irq 118 [0029.739] register 'maxim,max77620' pmic [0029.743] gpio_driver_register: register 'max77620-gpio' driver [0029.750] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.762] I2C Bus Init done [0029.765] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0029.773] calling apps_init() [0029.778] Found 19 GPT partitions in "sdmmc3_user" [0029.783] Proceeding to flashing Server [0029.787] usbdcd_reinit Initialize driver to use already enumerated device [0029.794] nv3p_priv_usbf_open USB configuration success [0029.803] Writing GPT partition [0029.808] Erasing Boot device [0029.835] Erasing Storage Device [0030.087] Sanitizing Storage Device [0030.212] Writing protective mbr [0030.216] Writing primary GPT [0030.222] Writing secondary GPT [0030.227] Found 18 GPT partitions in "sdmmc3_user" [0030.234] Writing NVC partition [0030.237] bct_init bctinit [0030.240] bct_init bctinit [0030.251] bct_init bctinit [0030.253] bct_init bctinit [0030.256] bct_init bctinit [0030.290] partition NVC write successful. [0030.296] Writing APP partition [0030.299] bct_init bctinit [0031.359] bct_init bctinit [0031.362] bct_init bctinit [0031.966] partition APP write successful. [0031.972] Writing TBC partition [0031.975] bct_init bctinit [0031.982] bct_init bctinit [0031.984] bct_init bctinit [0031.990] partition TBC write successful. [0031.996] Writing EBT partition [0031.999] bct_init bctinit [0032.023] bct_init bctinit [0032.026] bct_init bctinit [0032.036] partition EBT write successful. [0032.042] Writing BPF partition [0032.045] bct_init bctinit [0032.055] bct_init bctinit [0032.058] bct_init bctinit [0032.063] partition BPF write successful. [0032.069] Writing WB0 partition [0032.072] bct_init bctinit [0032.076] bct_init bctinit [0032.078] bct_init bctinit [0032.083] partition WB0 write successful. [0032.089] Writing RP1 partition [0032.092] bct_init bctinit [0032.112] bct_init bctinit [0032.115] bct_init bctinit [0032.124] partition RP1 write successful. [0032.130] Writing TOS partition [0032.133] bct_init bctinit [0032.140] bct_init bctinit [0032.143] bct_init bctinit [0032.148] partition TOS write successful. [0032.154] Writing DTB partition [0032.157] bct_init bctinit [0032.178] bct_init bctinit [0032.180] bct_init bctinit [0032.191] partition DTB write successful. [0032.203] Writing BCT partition [0032.208] bct_init bctinit [0032.306] partition BCT write successful. [0032.318] Change state to cold boot mode [0032.322] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.159] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.167] Power-up reason: software reset [0000.171] No Battery Present [0000.173] RamCode = 0 [0000.176] Platform has Ddr4 type ram [0000.179] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0xb0af8 [0000.195] Entering ramdump check [0000.198] Get RamDumpCarveOut = 0x0 [0000.201] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.211] Sdram initialization is successful [0000.215] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.236] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.241] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.246] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.267] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.272] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.313] Using GPT Primary to query partitions [0000.318] Loading Tboot-CPU binary [0000.367] Verifying bootloader in OdmNonSecureSBK mode [0000.377] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.384] Bootloader downloaded successfully. [0000.388] Downloaded Tboot-CPU binary to 0xa0000258 [0000.393] MAX77620_GPIO1 Configured. [0000.397] MAX77620_GPIO5 Configured. [0000.400] CPU power rail is up [0000.403] CPU clock enabled [0000.407] Performing RAM repair [0000.410] Updating A64 Warmreset Address to 0xa00002e9 [0000.427] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.542] Verifying bootloader in OdmNonSecureSBK mode [0000.648] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.655] Bootloader downloaded successfully. [0000.659] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.666] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.678] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.721] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.728] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.736] GSC3 address : ff500000 [0000.740] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.747] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.767] NvTbootPackSdramParams: start. [0000.772] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132661 us [0000.779] Basic modules init took 292407 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12213 us [0000.801] Carveout took 264407 us [0000.804] CPU initialization took 92764 us [0000.808] Total time taken by TegraBoot 661791 us [0000.812] Starting CPU & Halting co-processor 64b[0000.920] RamCode = 0 [0000.935] LPDDR4 Training: Read DT: Number of tables = 10 [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.956] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.964] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.052] EMC Training Successful [0001.055] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.078] Switching to 800000 KHz Success [0001.084] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.103] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.116] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.135] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 é[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.127] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.135] Power-up reason: reset button [0000.138] No Battery Present [0000.141] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.151] Setting Ddr voltage to 1125mv [0000.155] Serial Number of Pmic Max77663: 0xb0af8 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.174] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.219] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.243] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.253] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.411] Kernel DTB Load Address: 0x83080000 [0000.416] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.630] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.642] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.659] WB0 init successful [0000.685] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.692] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.700] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.718] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99645 us [0000.747] Basic modules init took 292144 us [0000.751] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.757] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12213 us [0000.768] Carveout took 264402 us [0000.771] CPU initialization took 92767 us [0000.775] Total time taken by TegraBoot 661526 us [0000.780] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.913] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.921] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.929] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.937] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.946] EMC Training Successful [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.955] EMC Training Successful [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.995] EMC Training Successful [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.042] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.058] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.077] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.096] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.109] DT Write: emc-table@1600000 succeeded [0001.113] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 74 ms (4.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915289 bytes read in 209 ms (31.6 MiB/s) Retrieving file: /boot/Image 17527296 bytes read in 445 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2677/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.456496] console [ttyS0] enabled [ 0.456496] console [ttyS0] enabled [ 0.463585] bootconsole [uart0] disabled [ 0.463585] bootconsole [uart0] disabled [ 0.472041] SuperH (H)SCI(F) driver initialized [ 0.476928] msm_serial: driver initialized [ 0.481542] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.492452] loop: module loaded [ 0.496866] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.508581] max77620-sd0: supplied by regulator-dummy [ 0.514929] max77620-sd1: supplied by regulator-dummy [ 0.521055] max77620-sd2: supplied by regulator-dummy [ 0.526947] max77620-sd3: supplied by regulator-dummy [ 0.533350] max77620-ldo0: supplied by regulator-dummy [ 0.539410] max77620-ldo1: supplied by regulator-dummy [ 0.545130] max77620-ldo2: supplied by regulator-dummy [ 0.551153] max77620-ldo3: supplied by regulator-dummy [ 0.556312] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.563177] max77620-ldo4: supplied by regulator-dummy [ 0.568333] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.574896] max77620-ldo5: supplied by regulator-dummy [ 0.580073] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.587060] max77620-ldo6: supplied by regulator-dummy [ 0.592214] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.599099] max77620-ldo7: supplied by regulator-dummy [ 0.605069] max77620-ldo8: supplied by regulator-dummy [ 0.615743] libphy: Fixed MDIO Bus: probed [ 0.620276] tun: Universal TUN/TAP device driver, 1.6 [ 0.625941] thunder_xcv, ver 1.0 [ 0.629188] thunder_bgx, ver 1.0 [ 0.632450] nicpf, ver 1.0 [ 0.635417] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.641249] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.647192] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.654150] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.659748] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.667572] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.673737] sky2: driver version 1.30 [ 0.677693] usbcore: registered new interface driver r8152 [ 0.683284] VFIO - User Level meta-driver version: 0.3 [ 0.689220] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.695747] ehci-pci: EHCI PCI platform driver [ 0.700222] ehci-platform: EHCI generic platform driver [ 0.705541] ehci-orion: EHCI orion driver [ 0.709628] ehci-exynos: EHCI EXYNOS driver [ 0.713882] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.720066] ohci-pci: OHCI PCI platform driver [ 0.724531] ohci-platform: OHCI generic platform driver [ 0.729838] ohci-exynos: OHCI EXYNOS driver [ 0.734546] usbcore: registered new interface driver usb-storage [ 0.873469] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.881715] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.888872] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.895184] i2c /dev entries driver [ 0.901557] sdhci: Secure Digital Host Controller Interface driver [ 0.907735] sdhci: Copyright(c) Pierre Ossman [ 0.912248] Synopsys Designware Multimedia Card Interface Driver [ 0.918858] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.924779] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.945282] mmc0: Unknown controller version (3). You may experience problems. [ 0.981864] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.990811] ledtrig-cpu: registered to indicate activity on CPUs [ 0.997687] usbcore: registered new interface driver usbhid [ 1.003316] usbhid: USB HID core driver [ 1.008786] NET: Registered protocol family 17 [ 1.013319] 9pnet: Installing 9P2000 support [ 1.017653] Key type dns_resolver registered [ 1.022421] registered taskstats version 1 [ 1.026584] Loading compiled-in X.509 certificates [ 1.038851] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.043780] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.049554] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.054871] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.060802] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.067506] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.072752] RTL_5V: supplied by VDD_5V0_SYS [ 1.077167] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.083252] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.088212] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.101349] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.108325] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.115127] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.121922] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.129429] mmc0: new high speed MMC card at address 0001 [ 1.135396] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.140407] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.146764] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.152818] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.160494] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.167478] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.174510] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.182267] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.583816] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.992905] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.401992] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.409491] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.414989] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.423185] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.824764] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.233848] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.642926] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.650423] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.655997] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.662266] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.668445] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.675313] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.682618] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.688582] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.696612] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.705967] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.773905] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.781314] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.786725] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.795278] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.803914] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.810323] hub 1-0:1.0: USB hub found [ 3.814101] hub 1-0:1.0: 5 ports detected [ 3.818446] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.823852] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.831475] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.839867] hub 2-0:1.0: USB hub found [ 3.843641] hub 2-0:1.0: 4 ports detected [ 3.848807] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.861911] mmc1: Unknown controller version (3). You may experience problems. [ 3.900675] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.908825] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.920996] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.928674] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.935784] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.947931] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.965593] max77686-rtc max77620-rtc: setting system clock to 2018-02-02 05:00:31 UTC (1517547631) [ 4.185759] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.212400] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.225068] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.350150] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.410312] r8152 2-1:1.0 eth0: v1.09.9 [ 4.414362] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.426498] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.799870] r8152 2-1:1.0 eth0: carrier on [ 8.829259] IP-Config: Complete: [ 8.832484] device=eth0, hwaddr=00:04:4b:79:7d:b8, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.842648] host=192.168.99.2, domain=, nis-domain=(none) [ 8.848478] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.855903] AVDD_DSI_CSI_1V2: disabling [ 8.859751] VDD_PRE_REG_1V35: disabling [ 8.863592] VDD_CAM_HV: disabling [ 8.867039] VDD_TS_HV: disabling [ 8.870394] VDD_TS_1V8: disabling [ 8.873715] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.878073] VDD_3V3_SD: disabling [ 8.881388] VDD_HDMI_5V0: disabling [ 8.884867] ALSA device list: [ 8.887831] No soundcards found. [ 8.891941] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 05:00:36 ] L4T-INITRD Build DATE: Fri Feb 2 05:00:36 UTC 2018 [ 05:00:36 ] Root device found: nfs [ 05:00:36 ] Ethernet interfaces: eth0 [ 05:00:36 ] IP Address: 192.168.99.2 [ 05:00:36 ] Rootfs mounted over nfs [ 05:00:36 ] Switching from initrd to actual rootfs [ 9.661549] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.679897] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.702905] systemd[1]: Set hostname to . [ 10.099125] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 10.117513] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 10.133312] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.149636] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 10.165550] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.185308] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 10.201391] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Starting Create Static Device Nodes in /dev... Mounting Debug File System... Starting Remount Root and Kernel File Systems... Mounting POSIX Message Queue File System... Mounting RPC Pipe File System... Mounting Huge Pages File System... [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Paths. Starting Journal Service... [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Mounting Configuration File System... [ OK ] Mounted Configuration File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting udev Kernel Device Manager... Starting Flush Journal to Persistent Storage... [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ 10.915811] systemd-journald[1567]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ 11.743534] random: crng init done [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting Login Service... Starting OpenBSD Secure Shell server... [ OK ] Started Daily Cleanup of Temporary Directories. Starting System Logging Service... [ OK ] Started Regular background program processing daemon. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. Starting Permit User Sessions... [ OK ] Started D-Bus System Message Bus. [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Login Service. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: I[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.127] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.135] Power-up reason: reset button [0000.138] No Battery Present [0000.141] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.151] Setting Ddr voltage to 1125mv [0000.155] Serial Number of Pmic Max77663: 0xb0af8 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.174] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.219] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.243] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.253] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.411] Kernel DTB Load Address: 0x83080000 [0000.416] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.630] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.642] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.659] WB0 init successful [0000.685] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.692] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.700] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.718] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99603 us [0000.747] Basic modules init took 292161 us [0000.751] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.757] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12214 us [0000.768] Carveout took 264402 us [0000.771] CPU initialization took 92765 us [0000.775] Total time taken by TegraBoot 661542 us [0000.780] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.913] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.921] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.929] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.937] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.946] EMC Training Successful [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.955] EMC Training Successful [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.995] EMC Training Successful [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.042] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.058] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.077] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.096] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.109] DT Write: emc-table@1600000 succeeded [0001.113] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 74 ms (4.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915289 bytes read in 209 ms (31.6 MiB/s) Retrieving file: /boot/Image 17527296 bytes read in 445 ms (37.6 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2677/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.455146] console [ttyS0] enabled [ 0.455146] console [ttyS0] enabled [ 0.462240] bootconsole [uart0] disabled [ 0.462240] bootconsole [uart0] disabled [ 0.470696] SuperH (H)SCI(F) driver initialized [ 0.475577] msm_serial: driver initialized [ 0.480233] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.490626] loop: module loaded [ 0.494989] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.506714] max77620-sd0: supplied by regulator-dummy [ 0.513059] max77620-sd1: supplied by regulator-dummy [ 0.519193] max77620-sd2: supplied by regulator-dummy [ 0.525074] max77620-sd3: supplied by regulator-dummy [ 0.531488] max77620-ldo0: supplied by regulator-dummy [ 0.537542] max77620-ldo1: supplied by regulator-dummy [ 0.543268] max77620-ldo2: supplied by regulator-dummy [ 0.549285] max77620-ldo3: supplied by regulator-dummy [ 0.554446] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.561310] max77620-ldo4: supplied by regulator-dummy [ 0.566470] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.573034] max77620-ldo5: supplied by regulator-dummy [ 0.578209] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.585193] max77620-ldo6: supplied by regulator-dummy [ 0.590353] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.597232] max77620-ldo7: supplied by regulator-dummy [ 0.603193] max77620-ldo8: supplied by regulator-dummy [ 0.613767] libphy: Fixed MDIO Bus: probed [ 0.618180] tun: Universal TUN/TAP device driver, 1.6 [ 0.623844] thunder_xcv, ver 1.0 [ 0.627107] thunder_bgx, ver 1.0 [ 0.630364] nicpf, ver 1.0 [ 0.633315] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.639145] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.645090] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.652045] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.657654] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.665477] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.671646] sky2: driver version 1.30 [ 0.675603] usbcore: registered new interface driver r8152 [ 0.681188] VFIO - User Level meta-driver version: 0.3 [ 0.687129] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.693654] ehci-pci: EHCI PCI platform driver [ 0.698125] ehci-platform: EHCI generic platform driver [ 0.703442] ehci-orion: EHCI orion driver [ 0.707524] ehci-exynos: EHCI EXYNOS driver [ 0.711776] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.717960] ohci-pci: OHCI PCI platform driver [ 0.722426] ohci-platform: OHCI generic platform driver [ 0.727732] ohci-exynos: OHCI EXYNOS driver [ 0.732436] usbcore: registered new interface driver usb-storage [ 0.871336] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.879555] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.886730] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.893040] i2c /dev entries driver [ 0.899392] sdhci: Secure Digital Host Controller Interface driver [ 0.905575] sdhci: Copyright(c) Pierre Ossman [ 0.910082] Synopsys Designware Multimedia Card Interface Driver [ 0.916698] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.922620] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.943866] mmc0: Unknown controller version (3). You may experience problems. [ 0.981687] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.990629] ledtrig-cpu: registered to indicate activity on CPUs [ 0.997454] usbcore: registered new interface driver usbhid [ 1.003079] usbhid: USB HID core driver [ 1.008529] NET: Registered protocol family 17 [ 1.013060] 9pnet: Installing 9P2000 support [ 1.017389] Key type dns_resolver registered [ 1.022205] registered taskstats version 1 [ 1.026305] Loading compiled-in X.509 certificates [ 1.038241] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.043185] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.048941] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.054235] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.060185] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.066877] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.068744] mmc0: new high speed MMC card at address 0001 [ 1.072080] RTL_5V: supplied by VDD_5V0_SYS [ 1.077453] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.081386] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.086061] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.091765] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.096664] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.101191] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.106950] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.119929] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.127244] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.132576] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.146834] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.153594] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.161965] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.168772] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.176977] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.578535] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.987616] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.396694] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.404189] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.409681] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.417876] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.819453] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.228528] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.637605] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.645098] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.650676] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.656942] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.663120] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.669988] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.677293] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.683159] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.691275] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.700611] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.770302] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777703] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.783113] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791687] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.800321] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806749] hub 1-0:1.0: USB hub found [ 3.810528] hub 1-0:1.0: 5 ports detected [ 3.814879] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.820282] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827903] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.836290] hub 2-0:1.0: USB hub found [ 3.840066] hub 2-0:1.0: 4 ports detected [ 3.845223] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.858313] mmc1: Unknown controller version (3). You may experience problems. [ 3.897087] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.905227] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.917395] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.925070] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.932430] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.944602] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.961963] max77686-rtc max77620-rtc: setting system clock to 2018-02-02 05:01:32 UTC (1517547692) [ 4.178155] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.204844] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.217635] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.342548] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.402722] r8152 2-1:1.0 eth0: v1.09.9 [ 4.406775] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.418915] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.796260] r8152 2-1:1.0 eth0: carrier on [ 8.821655] IP-Config: Complete: [ 8.824878] device=eth0, hwaddr=00:04:4b:79:7d:b8, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.835042] host=192.168.99.2, domain=, nis-domain=(none) [ 8.840870] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.848280] AVDD_DSI_CSI_1V2: disabling [ 8.852130] VDD_PRE_REG_1V35: disabling [ 8.855971] VDD_CAM_HV: disabling [ 8.859416] VDD_TS_HV: disabling [ 8.862770] VDD_TS_1V8: disabling [ 8.866091] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.870447] VDD_3V3_SD: disabling [ 8.873761] VDD_HDMI_5V0: disabling [ 8.877241] ALSA device list: [ 8.880205] No soundcards found. [ 8.884309] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 05:01:37 ] L4T-INITRD Build DATE: Fri Feb 2 05:01:37 UTC 2018 [ 05:01:37 ] Root device found: nfs [ 05:01:37 ] Ethernet interfaces: eth0 [ 05:01:37 ] IP Address: 192.168.99.2 [ 05:01:37 ] Rootfs mounted over nfs [ 05:01:37 ] Switching from initrd to actual rootfs [ 9.107093] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.125444] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.146622] systemd[1]: Set hostname to . [ 9.416064] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 9.433742] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.449867] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 9.465800] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 9.481704] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 9.497835] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 9.521810] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on Syslog Socket. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-getty.slice. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Mounting Debug File System... Starting Create Static Device Nodes in /dev... Mounting Huge Pages File System... Mounting RPC Pipe File System... Starting Journal Service... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Mounting Configuration File System... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Apply Kernel Variables. [ OK ] Started udev Kernel Device Manager. [ 10.175457] systemd-journald[1561]: Received request to flush runtime journal from PID 1 Starting Raise network interfaces... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Started Daily apt activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting OpenBSD Secure Shell server... Starting Login Service... Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... Starting Permit User Sessions... [ OK ] Started D-Bus System Message Bus. Starting System Logging Service... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started System Logging Servi[ 11.443987] random: crng init done ce. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: