U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################### 4 MiB/s done Bytes transferred = 8167936 (7ca200 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7ca200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.15.0-next-20180201-348720-gf26e52e08ab8 (jonathanh@tamien) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Wed Jan 31 20:49:02 PST 2018 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39232 r8192 d22208 u69632 [ 0.000000] pcpu-alloc: s39232 r8192 d22208 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1992472K/2096128K available (11264K kernel code, 1570K rwdata, 4352K rodata, 2048K init, 405K bss, 38120K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1571 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 406 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000044] Switching to timer-based delay loop, resolution 1000ns [ 0.005531] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005550] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005570] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005585] Switching to timer-based delay loop, resolution 83ns [ 0.006038] Console: colour dummy device 80x30 [ 0.006073] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.006091] pid_max: default: 32768 minimum: 301 [ 0.006209] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006224] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006720] CPU: Testing write buffer coherency: ok [ 0.006986] /cpus/cpu@0 missing clock-frequency property [ 0.007031] /cpus/cpu@1 missing clock-frequency property [ 0.007076] /cpus/cpu@2 missing clock-frequency property [ 0.007123] /cpus/cpu@3 missing clock-frequency property [ 0.007137] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007441] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.009440] Hierarchical SRCU implementation. [ 0.012498] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.013358] EFI services will not be available. [ 0.013521] smp: Bringing up secondary CPUs ... [ 0.014020] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015967] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025998] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035531] smp: Brought up 1 node, 4 CPUs [ 0.035554] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035563] CPU: All CPU(s) started in SVC mode. [ 0.037080] devtmpfs: initialized [ 0.051707] Built 1 zonelists, mobility grouping on. Total pages: 514502 [ 0.052060] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.052487] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.052507] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052697] pinctrl core: initialized pinctrl subsystem [ 0.054191] DMI not present or invalid. [ 0.054440] NET: Registered protocol family 16 [ 0.056469] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058967] cpuidle: using governor menu [ 0.083994] No ATAGs? [ 0.084124] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.084141] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.091838] Serial: AMBA PL011 UART driver [ 0.093282] iommu: Adding device 50000000.host1x to group 0 [ 0.093361] iommu: Adding device 54200000.dc to group 1 [ 0.093422] iommu: Adding device 54240000.dc to group 1 [ 0.093497] iommu: Adding device 57000000.gpu to group 2 [ 0.108726] AT91: Could not find identification node [ 0.109282] +5V_SYS: supplied by +VDD_MUX [ 0.109567] +3.3V_SYS: supplied by +VDD_MUX [ 0.110178] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.110194] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.110294] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.110308] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.110488] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.110503] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.110597] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.110610] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.110705] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.110718] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.110812] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.110826] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.113841] vgaarb: loaded [ 0.114569] SCSI subsystem initialized [ 0.114749] libata version 3.00 loaded. [ 0.114940] usbcore: registered new interface driver usbfs [ 0.114995] usbcore: registered new interface driver hub [ 0.115058] usbcore: registered new device driver usb [ 0.118540] pps_core: LinuxPPS API ver. 1 registered [ 0.118551] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.118575] PTP clock support registered [ 0.118766] EDAC MC: Ver: 3.0.0 [ 0.121761] clocksource: Switched to clocksource arch_sys_counter [ 0.173280] NET: Registered protocol family 2 [ 0.173787] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.173820] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.173919] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.174107] TCP: Hash tables configured (established 8192 bind 8192) [ 0.174189] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.174240] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.174388] NET: Registered protocol family 1 [ 0.174705] RPC: Registered named UNIX socket transport module. [ 0.174716] RPC: Registered udp transport module. [ 0.174725] RPC: Registered tcp transport module. [ 0.174734] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.174747] PCI: CLS 0 bytes, default 64 [ 0.176218] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.177727] Initialise system trusted keyrings [ 0.177860] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.184546] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.185127] NFS: Registering the id_resolver key type [ 0.185148] Key type id_resolver registered [ 0.185158] Key type id_legacy registered [ 0.185199] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.186736] Key type asymmetric registered [ 0.186748] Asymmetric key parser 'x509' registered [ 0.186798] bounce: pool size: 64 pages [ 0.186846] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.186858] io scheduler noop registered [ 0.186867] io scheduler deadline registered [ 0.187088] io scheduler cfq registered (default) [ 0.187100] io scheduler mq-deadline registered [ 0.187110] io scheduler kyber registered [ 0.191191] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.191300] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.191699] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.210880] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.210942] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.217794] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.224300] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.227709] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.276409] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.278993] console [ttyS0] disabled [ 0.279034] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.216213] console [ttyS0] enabled [ 1.220582] SuperH (H)SCI(F) driver initialized [ 1.226253] msm_serial: driver initialized [ 1.230535] STMicroelectronics ASC driver initialized [ 1.236290] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.245554] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.260233] Failed to attached device 54200000.dc to IOMMU_mapping [ 1.274662] Failed to attached device 54240000.dc to IOMMU_mapping [ 1.289548] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.306704] brd: module loaded [ 1.316098] loop: module loaded [ 1.320521] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.328865] as3722 4-0040: AS3722 with revision 0x1 found [ 1.340368] as3722-sd2: supplied by +5V_SYS [ 1.344987] as3722-sd3: supplied by +5V_SYS [ 1.349375] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.355791] as3722-sd4: supplied by +5V_SYS [ 1.360378] as3722-sd5: supplied by +5V_SYS [ 1.366332] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.372334] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.378521] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.384394] as3722-ldo3: supplied by +3.3V_SYS [ 1.388871] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.396637] as3722-ldo4: supplied by +3.3V_SYS [ 1.401295] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.407499] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.412344] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.419220] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.424894] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.431072] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.443704] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.466160] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.473594] libphy: Fixed MDIO Bus: probed [ 1.478613] CAN device driver interface [ 1.483416] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.490481] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.496326] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.502293] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.509243] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.518869] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.526315] usbcore: registered new interface driver pegasus [ 1.532023] usbcore: registered new interface driver asix [ 1.537442] usbcore: registered new interface driver ax88179_178a [ 1.543570] usbcore: registered new interface driver cdc_ether [ 1.549434] usbcore: registered new interface driver smsc75xx [ 1.555231] usbcore: registered new interface driver smsc95xx [ 1.560999] usbcore: registered new interface driver net1080 [ 1.566693] usbcore: registered new interface driver cdc_subset [ 1.572648] usbcore: registered new interface driver zaurus [ 1.578259] usbcore: registered new interface driver cdc_ncm [ 1.584156] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.589745] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.597239] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.603775] ehci-pci: EHCI PCI platform driver [ 1.608249] ehci-platform: EHCI generic platform driver [ 1.613706] ehci-orion: EHCI orion driver [ 1.617876] SPEAr-ehci: EHCI SPEAr driver [ 1.622040] ehci-st: EHCI STMicroelectronics driver [ 1.627052] ehci-exynos: EHCI EXYNOS driver [ 1.631391] ehci-atmel: EHCI Atmel driver [ 1.635556] tegra-ehci: Tegra EHCI driver [ 1.642405] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.647817] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.655617] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 1.681791] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.688375] hub 1-0:1.0: USB hub found [ 1.692181] hub 1-0:1.0: 1 port detected [ 1.696682] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.702903] ohci-pci: OHCI PCI platform driver [ 1.707382] ohci-platform: OHCI generic platform driver [ 1.712828] SPEAr-ohci: OHCI SPEAr driver [ 1.716980] ohci-st: OHCI STMicroelectronics driver [ 1.722018] ohci-atmel: OHCI Atmel driver [ 1.726826] usbcore: registered new interface driver usb-storage [ 1.741729] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.748632] as3722-rtc as3722-rtc: RTC interrupt 379 [ 1.757051] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.764241] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.770973] i2c /dev entries driver [ 1.781618] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.799409] sdhci: Secure Digital Host Controller Interface driver [ 1.805610] sdhci: Copyright(c) Pierre Ossman [ 1.811736] Synopsys Designware Multimedia Card Interface Driver [ 1.819311] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.825792] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.830683] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.851962] mmc0: Unknown controller version (3). You may experience problems. [ 1.859221] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.896199] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.905829] ledtrig-cpu: registered to indicate activity on CPUs [ 1.912228] usbcore: registered new interface driver usbhid [ 1.917870] usbhid: USB HID core driver [ 1.926390] NET: Registered protocol family 10 [ 1.931896] Segment Routing with IPv6 [ 1.935717] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.942244] NET: Registered protocol family 17 [ 1.946713] can: controller area network core (rev 20170425 abi 9) [ 1.952979] NET: Registered protocol family 29 [ 1.957418] can: raw protocol (rev 20170425) [ 1.961682] can: broadcast manager protocol (rev 20170425 t) [ 1.967358] can: netlink gateway (rev 20170425) max_hops=1 [ 1.973132] Key type dns_resolver registered [ 1.977918] ThumbEE CPU extension supported. [ 1.982211] Registering SWP/SWPB emulation handler [ 1.987505] Loading compiled-in X.509 certificates [ 2.005823] +3.3V_RUN: supplied by +3.3V_SYS [ 2.010988] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.015834] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.022180] +5V_USB_HS: supplied by +5V_SYS [ 2.027676] +3.3V_LP0: supplied by +3.3V_SYS [ 2.033900] +5V_HDMI_CON: supplied by +5V_SYS [ 2.039188] +5V_SATA: supplied by +5V_SYS [ 2.039336] mmc0: new high speed MMC card at address 0001 [ 2.044083] +12V_SATA: supplied by +VDD_MUX [ 2.049307] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.054507] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.057779] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.064253] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.070444] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.077045] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.083182] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (236:0) [ 2.090826] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.102390] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.112323] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.120508] mmcblk0: p1 [ 2.123726] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.133204] as3722-sd2: supplied by +5V_SYS [ 2.137612] as3722-sd3: supplied by +5V_SYS [ 2.142139] as3722-sd4: supplied by +5V_SYS [ 2.146644] as3722-sd5: supplied by +5V_SYS [ 2.152415] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.157831] as3722-ldo1: supplied by +3.3V_RUN [ 2.162652] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.168144] as3722-ldo3: supplied by +3.3V_SYS [ 2.173589] as3722-ldo4: supplied by +3.3V_SYS [ 2.178265] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.183281] as3722-ldo6: supplied by +3.3V_RUN [ 2.187958] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.193329] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.200348] as3722-ldo9: supplied by +5V_SYS [ 2.205822] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.212522] as3722-ldo10: supplied by +5V_SYS [ 2.217604] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.224399] as3722-ldo11: supplied by +3.3V_RUN [ 2.229653] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.239707] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.248784] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.259309] scsi host0: tegra-ahci [ 2.264114] scsi host1: tegra-ahci [ 2.267753] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.275794] ata2: DUMMY [ 2.281893] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.287310] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.295061] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 2.321885] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.328836] hub 2-0:1.0: USB hub found [ 2.332698] hub 2-0:1.0: 1 port detected [ 2.339253] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.344216] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.355996] mmc1: Unknown controller version (3). You may experience problems. [ 2.363354] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.401371] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.409589] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.417085] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.424724] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.450079] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.458355] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.472321] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.478589] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.484810] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.491692] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.499053] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.504634] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.510664] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.520370] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.530096] pci 0000:00:01.0: enabling Extended Tags [ 2.535122] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.544934] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.554755] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.561386] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.571446] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.577524] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.587224] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.596949] pci 0000:00:02.0: enabling Extended Tags [ 2.601976] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.605585] ata1: SATA link down (SStatus 0 SControl 300) [ 2.611739] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.626911] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.633545] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.643582] PCI: bus0: Fast back to back transfers disabled [ 2.649164] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.657218] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.665431] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.671503] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.678529] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.698425] mmc1: new high speed SDHC card at address aaaa [ 2.704561] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.711852] PCI: bus1: Fast back to back transfers disabled [ 2.717465] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.724298] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.730359] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.736012] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.742835] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.750221] pci 0000:02:00.0: supports D1 D2 [ 2.754506] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.769019] mmcblk1: p1 p2 p3 [ 2.781935] PCI: bus2: Fast back to back transfers disabled [ 2.787526] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.794229] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.801012] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.807849] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.815607] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.821703] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.829081] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.834071] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.840868] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.848677] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.856022] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.862171] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.867138] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.873252] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.880033] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.887851] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.894970] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.901294] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 2.907250] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.914354] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.920679] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 2.926869] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.932490] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.963409] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xcb2dba36, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 397 [ 2.973105] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.985668] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.994038] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.000662] [drm] No driver support for vblank timestamp query. [ 3.133970] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.296878] Console: switching to colour frame buffer device 512x135 [ 3.395707] drm drm: fb0: frame buffer device [ 3.400277] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.408212] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.415556] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.424656] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.431567] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:04:12 UTC (946685052) [ 3.440546] +USB0_VBUS_SW: disabling [ 3.444170] +1.8V_RUN_CAM: disabling [ 3.447872] +2.8V_RUN_CAM: disabling [ 3.451610] +1.2V_RUN_CAM_FRONT: disabling [ 3.455944] +1.05V_RUN_CAM_REAR: disabling [ 3.460201] +3.3V_RUN_TOUCH: disabling [ 3.464121] +2.8V_RUN_CAM_AF: disabling [ 3.468064] +1.8V_RUN_VPP_FUSE: disabling [ 3.473033] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.522640] EXT4-fs (mmcblk0p1): recovery complete [ 3.528380] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.536590] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.546873] devtmpfs: mounted [ 3.550588] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#