FAILED: Linux Boot Test 1 Test Owner(s): N/A Execution Time 175.25 sec Test TIMEOUT reached. Test did not report results in 120 secs Percent passed so far: 0.0 FAILED: Linux Boot Test 2 Test Owner(s): N/A Execution Time 175.19 sec Test TIMEOUT reached. Test did not report results in 120 secs Percent passed so far: 0.0 FAILED: Linux Boot Test 3 Test Owner(s): N/A Execution Time 175.26 sec Test TIMEOUT reached. Test did not report results in 120 secs Percent passed so far: 0.0 Final Score: 0.0 Sanity Failed! D[0031.740] Enabled early print [0031.742] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0031.748] Processing in recovery mode [0031.751] A02 Bootrom Patch rev = 63 [0031.755] Power-up reason: pmc por [0031.758] Established communication link with host [0032.725] Odmdata from BCT: 0x00084000 [0032.729] DebugPort= 0x3 [0032.731] BoardId read from EEPROM/NCT: 2180 [0032.759] Turned on fan for loki board [0032.763] Key release before reqd. time for fastboot [0032.768] No Battery Present [0032.770] RamCode = 0 [0032.773] Platform has Ddr4 type ram [0032.776] max77620 disabling SD1 Remote Sense [0032.780] Setting Ddr voltage to 1125mv [0032.784] Serial Number of Pmic Max77663: 0x50bb6 [0032.792] Entering ramdump check [0032.795] Get RamDumpCarveOut = 0x0 [0032.798] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0032.803] Last reboot was clean, booting normally! [0032.808] Sdram initialization is successful [0032.812] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0032.818] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0032.823] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0032.828] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0032.833] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0032.838] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0032.843] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0032.849] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0032.864] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0032.870] Platform-DebugCarveout: 0 [0032.873] Downloaded Bct successfully [0032.977] Downloaded bootloader successfully at 0x92c00000 [0033.077] Downloaded rp1 successfully at 0x83000000 [0033.125] MAX77620_GPIO1 Configured. [0033.128] MAX77620_GPIO5 Configured. [0033.132] CPU power rail is up [0033.134] CPU clock enabled [0033.138] Performing RAM repair [0033.141] Updating A64 Warmreset Address to 0x92c002e9 [0033.147] Enable APE clock/reset [0033.150] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0033.155] Loading Secure OS image failed. [0033.159] Set NvDecSticky Bits [0033.162] GSC1 address : ff700000 [0033.166] GSC2 address ff63fffc value c0edbbcc [0033.171] GSC2 address : ff600000 [0033.174] GSC3 address : ff500000 [0033.178] GSC4 address : ff400000 [0033.182] GSC5 address : ff300000 [0033.185] GSC MC Settings done [0033.188] NvTbootPackSdramParams: start. [0033.193] NvTbootPackSdramParams: done. [0033.197] Next binary entry address: 0x92c00258 [0033.201] BoardId: 2180 [0033.204] dram memory type is 3 [0033.207] Tegraboot started after 32501630 us [0033.211] Basic modules init took -32501630 us [0033.216] USB data transfer took 0 us [0033.219] Carveout took 34000991 us [0033.223] CPU initialization took 3629 us [0033.226] Total time taken by TegraBoot 1502990 us [0033.231] Starting CPU & Halting co-processor [0034.038] [0034.039] Debug Init done [0034.042] Marked DTB cacheable [0034.044] Bootloader DTB loaded at 0x83000000 [0034.049] DeviceTree Init done [0034.063] Pinmux applied successfully [0034.068] gicd_base: 0x50041000 [0034.072] gicc_base: 0x50042000 [0034.075] Interrupts Init done [0034.079] Using base:0x60005008 & irq:33 for tick-timer [0034.084] Using base:0x60005000 for delay-timer [0034.089] platform_init_timer: DONE [0034.092] Timer(tick) Init done [0034.097] osc freq = 38400 khz [0034.101] [0034.102] welcome to cboot [0034.105] [0034.106] Cboot Version: 24.00.2015.42-t210-63d15635 [0034.111] calling constructors [0034.114] initializing heap [0034.117] initializing threads [0034.120] initializing timers [0034.122] creating bootstrap completion thread [0034.127] top of bootstrap2() [0034.130] CPU: ARM Cortex A57 [0034.133] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0034.137] initializing platform [0034.164] config for ddr50 mode completed [0034.167] sdmmc bdev is already initialized [0034.172] of_register: registering tegra_udc to of_hal [0034.177] of_register: registering inv20628-driver to of_hal [0034.182] of_register: registering ads1015-driver to of_hal [0034.188] of_register: registering lp8557-bl-driver to of_hal [0034.194] of_register: registering bq2419x_charger to of_hal [0034.199] of_register: registering cpc to of_hal [0034.204] of_register: registering bq27441_fuel_gauge to of_hal [0034.218] gpio framework initialized [0034.222] of_register: registering tca9539_gpio to of_hal [0034.227] of_register: registering tca9539_gpio to of_hal [0034.232] of_register: registering i2c_bus_driver to of_hal [0034.238] of_register: registering i2c_bus_driver to of_hal [0034.243] of_register: registering i2c_bus_driver to of_hal [0034.249] pmic framework initialized [0034.252] of_register: registering max77620_pmic to of_hal [0034.258] regulator framework initialized [0034.262] of_register: registering tps65132_bl_driver to of_hal [0034.268] of_register: registering tegra_xhci to of_hal [0034.273] initializing target [0034.280] gpio_driver_register: register 'tegra_gpio_driver' driver [0034.289] fixed regulator driver initialized [0034.354] initializing OF layer [0034.359] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0034.367] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.388] I2C Bus Init done [0034.391] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.403] I2C Bus Init done [0034.406] of_children_init: Ops found for compatible string ti,lp8557 [0034.412] I2C slave not started [0034.415] I2C write failed [0034.418] Writing offset failed [0034.421] failed to read 0x 0 [0034.424] lp8557: Couldn't turn off backlight: -3 [0034.428] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0034.442] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0034.448] gpio_driver_register: register 'tca9539_gpio_driver' driver [0034.454] of_children_init: Ops found for compatible string ti,tca9539 [0034.465] tca9539_init: i2c bus: 2, slave addr: 0xee [0034.471] gpio_driver_register: register 'tca9539_gpio_driver' driver [0034.477] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.489] I2C Bus Init done [0034.492] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.504] I2C Bus Init done [0034.506] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.519] I2C Bus Init done [0034.521] of_children_init: Ops found for compatible string maxim,max77620 [0034.533] max77620_init using irq 118 [0034.538] register 'maxim,max77620' pmic [0034.543] gpio_driver_register: register 'max77620-gpio' driver [0034.549] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0034.561] I2C Bus Init done [0034.564] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0034.572] calling apps_init() [0034.578] Found 19 GPT partitions in "sdmmc3_user" [0034.583] Proceeding to flashing Server [0034.586] usbdcd_reinit Initialize driver to use already enumerated device [0034.593] nv3p_priv_usbf_open USB configuration success [0034.603] Writing GPT partition [0034.608] Erasing Boot device [0034.633] Erasing Storage Device [0034.902] Sanitizing Storage Device [0035.028] Writing protective mbr [0035.032] Writing primary GPT [0035.038] Writing secondary GPT [0035.043] Found 18 GPT partitions in "sdmmc3_user" [0035.050] Writing NVC partition [0035.053] bct_init bctinit [0035.056] bct_init bctinit [0035.066] bct_init bctinit [0035.069] bct_init bctinit [0035.072] bct_init bctinit [0035.104] partition NVC write successful. [0035.110] Writing APP partition [0035.113] bct_init bctinit [0036.174] bct_init bctinit [0036.176] bct_init bctinit [0036.819] partition APP write successful. [0036.826] Writing TBC partition [0036.829] bct_init bctinit [0036.836] bct_init bctinit [0036.838] bct_init bctinit [0036.846] partition TBC write successful. [0036.852] Writing EBT partition [0036.855] bct_init bctinit [0036.880] bct_init bctinit [0036.883] bct_init bctinit [0036.894] partition EBT write successful. [0036.900] Writing BPF partition [0036.903] bct_init bctinit [0036.909] bct_init bctinit [0036.911] bct_init bctinit [0036.924] partition BPF write successful. [0036.929] Writing WB0 partition [0036.932] bct_init bctinit [0036.937] bct_init bctinit [0036.939] bct_init bctinit [0036.948] partition WB0 write successful. [0036.954] Writing RP1 partition [0036.957] bct_init bctinit [0036.978] bct_init bctinit [0036.981] bct_init bctinit [0037.001] partition RP1 write successful. [0037.007] Writing TOS partition [0037.010] bct_init bctinit [0037.016] bct_init bctinit [0037.019] bct_init bctinit [0037.025] partition TOS write successful. [0037.031] Writing DTB partition [0037.034] bct_init bctinit [0037.054] bct_init bctinit [0037.057] bct_init bctinit [0037.067] partition DTB write successful. [0037.078] Writing BCT partition [0037.083] bct_init bctinit [0037.178] partition BCT write successful. [0037.190] Change state to cold boot mode [0037.194] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.186] Serial Number of Pmic Max77663: 0x50bb6 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.205] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132079 us [0000.779] Basic modules init took 292343 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12259 us [0000.800] Carveout took 264489 us [0000.803] CPU initialization took 92733 us [0000.807] Total time taken by TegraBoot 661824 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 È[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x50bb6 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.373] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99026 us [0000.746] Basic modules init took 292129 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12258 us [0000.768] Carveout took 264484 us [0000.771] CPU initialization took 92736 us [0000.775] Total time taken by TegraBoot 661607 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 66 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915798 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17457664 bytes read in 444 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2388/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.460136] console [ttyS0] enabled [ 0.460136] console [ttyS0] enabled [ 0.467228] bootconsole [uart0] disabled [ 0.467228] bootconsole [uart0] disabled [ 0.475738] SuperH (H)SCI(F) driver initialized [ 0.480574] msm_serial: driver initialized [ 0.485140] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.495500] loop: module loaded [ 0.499820] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.511529] max77620-sd0: supplied by regulator-dummy [ 0.518005] max77620-sd1: supplied by regulator-dummy [ 0.524124] max77620-sd2: supplied by regulator-dummy [ 0.530036] max77620-sd3: supplied by regulator-dummy [ 0.536439] max77620-ldo0: supplied by regulator-dummy [ 0.542497] max77620-ldo1: supplied by regulator-dummy [ 0.548234] max77620-ldo2: supplied by regulator-dummy [ 0.554231] max77620-ldo3: supplied by regulator-dummy [ 0.559393] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.566268] max77620-ldo4: supplied by regulator-dummy [ 0.571424] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.578014] max77620-ldo5: supplied by regulator-dummy [ 0.583171] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.590163] max77620-ldo6: supplied by regulator-dummy [ 0.595317] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.602204] max77620-ldo7: supplied by regulator-dummy [ 0.608195] max77620-ldo8: supplied by regulator-dummy [ 0.618762] libphy: Fixed MDIO Bus: probed [ 0.623138] tun: Universal TUN/TAP device driver, 1.6 [ 0.628781] thunder-xcv, ver 1.0 [ 0.632045] thunder-BGX, ver 1.0 [ 0.635304] thunder-nic, ver 1.0 [ 0.638781] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.644609] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.650559] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.657513] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.663107] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.670928] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.677094] sky2: driver version 1.30 [ 0.681042] usbcore: registered new interface driver r8152 [ 0.686629] VFIO - User Level meta-driver version: 0.3 [ 0.692573] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.699103] ehci-pci: EHCI PCI platform driver [ 0.703569] ehci-platform: EHCI generic platform driver [ 0.708887] ehci-orion: EHCI orion driver [ 0.712965] ehci-exynos: EHCI EXYNOS driver [ 0.717229] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.723409] ohci-pci: OHCI PCI platform driver [ 0.727884] ohci-platform: OHCI generic platform driver [ 0.733189] ohci-exynos: OHCI EXYNOS driver [ 0.737890] usbcore: registered new interface driver usb-storage [ 0.876796] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.885053] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.892213] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.898523] i2c /dev entries driver [ 0.904791] sdhci: Secure Digital Host Controller Interface driver [ 0.910972] sdhci: Copyright(c) Pierre Ossman [ 0.915484] Synopsys Designware Multimedia Card Interface Driver [ 0.922087] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.928006] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.949247] mmc0: Unknown controller version (3). You may experience problems. [ 0.987442] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.996507] ledtrig-cpu: registered to indicate activity on CPUs [ 1.003344] usbcore: registered new interface driver usbhid [ 1.008969] usbhid: USB HID core driver [ 1.014700] NET: Registered protocol family 17 [ 1.019298] 9pnet: Installing 9P2000 support [ 1.023667] Key type dns_resolver registered [ 1.028482] registered taskstats version 1 [ 1.032584] Loading compiled-in X.509 certificates [ 1.044675] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.049611] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.055365] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.060686] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.066622] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.072909] mmc0: new high speed MMC card at address 0001 [ 1.078687] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.078898] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.088181] RTL_5V: supplied by VDD_5V0_SYS [ 1.088301] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.092648] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.098711] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.109027] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.117071] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.117999] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.122048] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.142517] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.149447] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.156205] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.162971] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.171261] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.178023] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.186230] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.587787] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.996860] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.405917] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.413412] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.418903] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.427096] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.828649] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.237712] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.646778] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.654272] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.659838] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.666108] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.672287] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.679157] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.686461] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.692310] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.700365] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.709700] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.777870] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.785271] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.790680] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.799246] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.807881] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.814312] hub 1-0:1.0: USB hub found [ 3.818092] hub 1-0:1.0: 5 ports detected [ 3.822443] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.827848] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.835467] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.843851] hub 2-0:1.0: USB hub found [ 3.847626] hub 2-0:1.0: 4 ports detected [ 3.852776] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.865869] mmc1: Unknown controller version (3). You may experience problems. [ 3.904642] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.912781] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.924931] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.932606] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.939571] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.951765] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.981538] max77686-rtc max77620-rtc: setting system clock to 2017-04-08 21:44:11 UTC (1491687851) [ 4.185726] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.212361] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.224983] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.350114] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.410279] r8152 2-1:1.0 eth0: v1.09.9 [ 4.414337] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.426449] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.739808] r8152 2-1:1.0 eth0: carrier on [ 8.765224] IP-Config: Complete: [ 8.768447] device=eth0, hwaddr=00:04:4b:5a:c3:7e, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.778635] host=192.168.99.2, domain=, nis-domain=(none) [ 8.784465] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.791885] AVDD_DSI_CSI_1V2: disabling [ 8.795735] VDD_PRE_REG_1V35: disabling [ 8.799578] VDD_CAM_HV: disabling [ 8.803051] VDD_TS_HV: disabling [ 8.806408] VDD_TS_1V8: disabling [ 8.809729] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.814086] VDD_3V3_SD: disabling [ 8.817400] VDD_HDMI_5V0: disabling [ 8.820881] ALSA device list: [ 8.823847] No soundcards found. [ 8.828011] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 21:44:16 ] L4T-INITRD Build DATE: Sat Apr 8 21:44:16 UTC 2017 [ 21:44:16 ] Root device found: nfs [ 21:44:16 ] Ethernet interfaces: eth0 [ 21:44:16 ] ERROR: dhclient fail... bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell bash-4.3# ¤ð[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x50bb6 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99030 us [0000.746] Basic modules init took 292133 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12260 us [0000.768] Carveout took 264485 us [0000.771] CPU initialization took 92732 us [0000.775] Total time taken by TegraBoot 661610 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 66 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915798 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17457664 bytes read in 444 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2388/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.461162] console [ttyS0] enabled [ 0.461162] console [ttyS0] enabled [ 0.468258] bootconsole [uart0] disabled [ 0.468258] bootconsole [uart0] disabled [ 0.476788] SuperH (H)SCI(F) driver initialized [ 0.481622] msm_serial: driver initialized [ 0.486145] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.497208] loop: module loaded [ 0.501545] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.513271] max77620-sd0: supplied by regulator-dummy [ 0.519620] max77620-sd1: supplied by regulator-dummy [ 0.525767] max77620-sd2: supplied by regulator-dummy [ 0.531659] max77620-sd3: supplied by regulator-dummy [ 0.538082] max77620-ldo0: supplied by regulator-dummy [ 0.544136] max77620-ldo1: supplied by regulator-dummy [ 0.549869] max77620-ldo2: supplied by regulator-dummy [ 0.555890] max77620-ldo3: supplied by regulator-dummy [ 0.561047] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.567917] max77620-ldo4: supplied by regulator-dummy [ 0.573076] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.579636] max77620-ldo5: supplied by regulator-dummy [ 0.584810] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.591799] max77620-ldo6: supplied by regulator-dummy [ 0.596954] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.603839] max77620-ldo7: supplied by regulator-dummy [ 0.609799] max77620-ldo8: supplied by regulator-dummy [ 0.620469] libphy: Fixed MDIO Bus: probed [ 0.624958] tun: Universal TUN/TAP device driver, 1.6 [ 0.630587] thunder-xcv, ver 1.0 [ 0.633849] thunder-BGX, ver 1.0 [ 0.637097] thunder-nic, ver 1.0 [ 0.640574] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.646404] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.652354] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.659307] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.664903] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.672723] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.678901] sky2: driver version 1.30 [ 0.682848] usbcore: registered new interface driver r8152 [ 0.688429] VFIO - User Level meta-driver version: 0.3 [ 0.694366] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.700893] ehci-pci: EHCI PCI platform driver [ 0.705359] ehci-platform: EHCI generic platform driver [ 0.710677] ehci-orion: EHCI orion driver [ 0.714754] ehci-exynos: EHCI EXYNOS driver [ 0.719008] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.725190] ohci-pci: OHCI PCI platform driver [ 0.729661] ohci-platform: OHCI generic platform driver [ 0.734965] ohci-exynos: OHCI EXYNOS driver [ 0.739669] usbcore: registered new interface driver usb-storage [ 0.878511] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.886611] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.893770] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.900079] i2c /dev entries driver [ 0.906381] sdhci: Secure Digital Host Controller Interface driver [ 0.912574] sdhci: Copyright(c) Pierre Ossman [ 0.917088] Synopsys Designware Multimedia Card Interface Driver [ 0.923695] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.929608] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.949337] mmc0: Unknown controller version (3). You may experience problems. [ 0.985316] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.994173] ledtrig-cpu: registered to indicate activity on CPUs [ 1.001048] usbcore: registered new interface driver usbhid [ 1.006621] usbhid: USB HID core driver [ 1.012017] NET: Registered protocol family 17 [ 1.016518] 9pnet: Installing 9P2000 support [ 1.020803] Key type dns_resolver registered [ 1.025543] registered taskstats version 1 [ 1.029643] Loading compiled-in X.509 certificates [ 1.035549] mmc0: new high speed MMC card at address 0001 [ 1.041608] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.041821] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.046600] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.051082] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.057129] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.062488] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.067839] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.073046] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.081342] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.085673] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.098724] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.103936] RTL_5V: supplied by VDD_5V0_SYS [ 1.108369] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.114436] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.119357] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.132353] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.139272] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.146036] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.152785] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.161091] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.167839] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.176044] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.577603] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.986679] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.395770] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.403266] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.408758] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.416950] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.818513] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.227573] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.636647] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.644140] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.649713] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.655981] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.662160] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.669031] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.676337] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.682170] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.690213] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.699545] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.769963] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777363] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.782772] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791317] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.799956] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806389] hub 1-0:1.0: USB hub found [ 3.810168] hub 1-0:1.0: 5 ports detected [ 3.814520] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.819925] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827551] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.835935] hub 2-0:1.0: USB hub found [ 3.839716] hub 2-0:1.0: 4 ports detected [ 3.844867] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.857955] mmc1: Unknown controller version (3). You may experience problems. [ 3.896725] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.904866] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.916999] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.924670] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.931778] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.943918] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.961655] max77686-rtc max77620-rtc: setting system clock to 2017-04-08 21:47:10 UTC (1491688030) [ 4.181819] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.208597] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.221281] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.346202] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.406376] r8152 2-1:1.0 eth0: v1.09.9 [ 4.410423] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.422532] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.667909] r8152 2-1:1.0 eth0: carrier on [ 8.697313] IP-Config: Complete: [ 8.700538] device=eth0, hwaddr=00:04:4b:5a:c3:7e, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.710702] host=192.168.99.2, domain=, nis-domain=(none) [ 8.716530] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.723945] AVDD_DSI_CSI_1V2: disabling [ 8.727796] VDD_PRE_REG_1V35: disabling [ 8.731636] VDD_CAM_HV: disabling [ 8.735085] VDD_TS_HV: disabling [ 8.738440] VDD_TS_1V8: disabling [ 8.741761] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.746119] VDD_3V3_SD: disabling [ 8.749434] VDD_HDMI_5V0: disabling [ 8.752912] ALSA device list: [ 8.755879] No soundcards found. [ 8.759980] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 21:47:15 ] L4T-INITRD Build DATE: Sat Apr 8 21:47:15 UTC 2017 [ 21:47:15 ] Root device found: nfs [ 21:47:15 ] Ethernet interfaces: eth0 [ 21:47:15 ] ERROR: dhclient fail... bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell bash-4.3# 8H[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x50bb6 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.373] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99032 us [0000.746] Basic modules init took 292125 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12259 us [0000.768] Carveout took 264483 us [0000.771] CPU initialization took 92735 us [0000.775] Total time taken by TegraBoot 661602 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 66 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915798 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17457664 bytes read in 444 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2388/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 57 ms (902.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.464578] console [ttyS0] enabled [ 0.464578] console [ttyS0] enabled [ 0.471975] bootconsole [uart0] disabled [ 0.471975] bootconsole [uart0] disabled [ 0.480493] SuperH (H)SCI(F) driver initialized [ 0.485326] msm_serial: driver initialized [ 0.489889] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.500257] loop: module loaded [ 0.504594] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.516315] max77620-sd0: supplied by regulator-dummy [ 0.522654] max77620-sd1: supplied by regulator-dummy [ 0.528804] max77620-sd2: supplied by regulator-dummy [ 0.534688] max77620-sd3: supplied by regulator-dummy [ 0.541087] max77620-ldo0: supplied by regulator-dummy [ 0.547159] max77620-ldo1: supplied by regulator-dummy [ 0.552882] max77620-ldo2: supplied by regulator-dummy [ 0.558881] max77620-ldo3: supplied by regulator-dummy [ 0.564042] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.570932] max77620-ldo4: supplied by regulator-dummy [ 0.576090] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.582654] max77620-ldo5: supplied by regulator-dummy [ 0.587808] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.594793] max77620-ldo6: supplied by regulator-dummy [ 0.599947] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.606851] max77620-ldo7: supplied by regulator-dummy [ 0.612817] max77620-ldo8: supplied by regulator-dummy [ 0.623394] libphy: Fixed MDIO Bus: probed [ 0.627890] tun: Universal TUN/TAP device driver, 1.6 [ 0.633538] thunder-xcv, ver 1.0 [ 0.636789] thunder-BGX, ver 1.0 [ 0.640049] thunder-nic, ver 1.0 [ 0.643537] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.649368] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.655314] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.662270] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.667865] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.675687] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.681865] sky2: driver version 1.30 [ 0.685816] usbcore: registered new interface driver r8152 [ 0.691414] VFIO - User Level meta-driver version: 0.3 [ 0.697348] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.703873] ehci-pci: EHCI PCI platform driver [ 0.708344] ehci-platform: EHCI generic platform driver [ 0.713659] ehci-orion: EHCI orion driver [ 0.717744] ehci-exynos: EHCI EXYNOS driver [ 0.721996] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.728181] ohci-pci: OHCI PCI platform driver [ 0.732649] ohci-platform: OHCI generic platform driver [ 0.737955] ohci-exynos: OHCI EXYNOS driver [ 0.742652] usbcore: registered new interface driver usb-storage [ 0.881747] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.889973] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.897142] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.903450] i2c /dev entries driver [ 0.909817] sdhci: Secure Digital Host Controller Interface driver [ 0.915999] sdhci: Copyright(c) Pierre Ossman [ 0.920515] Synopsys Designware Multimedia Card Interface Driver [ 0.927118] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.933038] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.953465] mmc0: Unknown controller version (3). You may experience problems. [ 0.991757] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.000677] ledtrig-cpu: registered to indicate activity on CPUs [ 1.007566] usbcore: registered new interface driver usbhid [ 1.013193] usbhid: USB HID core driver [ 1.018652] NET: Registered protocol family 17 [ 1.023172] 9pnet: Installing 9P2000 support [ 1.027479] Key type dns_resolver registered [ 1.032209] registered taskstats version 1 [ 1.036328] Loading compiled-in X.509 certificates [ 1.048851] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.053769] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.059573] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.064865] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.070833] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.077559] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.082747] RTL_5V: supplied by VDD_5V0_SYS [ 1.087160] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.093288] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.098226] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.110944] mmc0: new high speed MMC card at address 0001 [ 1.116909] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.121987] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.128927] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.136076] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.142435] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.148457] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.155223] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.162022] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.171341] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.177780] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.186346] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.194810] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.596365] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.005459] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.414543] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.422039] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.427534] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.435726] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.837306] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.246389] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.655466] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.662961] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.668535] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.674805] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.680983] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.687854] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.695160] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.701105] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.709138] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.718474] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.786087] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.793495] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.798905] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.807477] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.816116] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.822545] hub 1-0:1.0: USB hub found [ 3.826326] hub 1-0:1.0: 5 ports detected [ 3.830674] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.836080] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.843702] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.852092] hub 2-0:1.0: USB hub found [ 3.855868] hub 2-0:1.0: 4 ports detected [ 3.861030] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.874126] mmc1: Unknown controller version (3). You may experience problems. [ 3.912904] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.921045] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.933190] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.940875] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.948105] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.960335] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.989759] max77686-rtc max77620-rtc: setting system clock to 2017-04-08 21:50:09 UTC (1491688209) [ 4.193941] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.220715] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.233396] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.358332] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.418493] r8152 2-1:1.0 eth0: v1.09.9 [ 4.422540] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.434650] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.668048] r8152 2-1:1.0 eth0: carrier on [ 8.693439] IP-Config: Complete: [ 8.696662] device=eth0, hwaddr=00:04:4b:5a:c3:7e, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.706851] host=192.168.99.2, domain=, nis-domain=(none) [ 8.712681] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.720102] AVDD_DSI_CSI_1V2: disabling [ 8.723953] VDD_PRE_REG_1V35: disabling [ 8.727795] VDD_CAM_HV: disabling [ 8.731267] VDD_TS_HV: disabling [ 8.734625] VDD_TS_1V8: disabling [ 8.737947] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.742304] VDD_3V3_SD: disabling [ 8.745619] VDD_HDMI_5V0: disabling [ 8.749098] ALSA device list: [ 8.752062] No soundcards found. [ 8.756166] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 21:50:14 ] L4T-INITRD Build DATE: Sat Apr 8 21:50:14 UTC 2017 [ 21:50:14 ] Root device found: nfs [ 21:50:14 ] Ethernet interfaces: eth0 [ 21:50:14 ] ERROR: dhclient fail... bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell bash-4.3# Ùô[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x50bb6 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.279] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.373] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99028 us [0000.746] Basic modules init took 292128 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12259 us [0000.768] Carveout took 264486 us [0000.771] CPU initialization took 92732 us [0000.775] Total time taken by TegraBoot 661605 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [000”