Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.29 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.9 sec Percent passed so far: 100.0 Final Score: 100.0 ü[0030.061] Enabled early print [0030.063] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0030.069] Processing in recovery mode [0030.072] A02 Bootrom Patch rev = 63 [0030.076] Power-up reason: pmc por [0030.079] Established communication link with host [0031.046] Odmdata from BCT: 0x00084000 [0031.050] DebugPort= 0x3 [0031.052] BoardId read from EEPROM/NCT: 2180 [0031.081] Turned on fan for loki board [0031.084] Key release before reqd. time for fastboot [0031.089] No Battery Present [0031.092] RamCode = 0 [0031.094] Platform has Ddr4 type ram [0031.097] max77620 disabling SD1 Remote Sense [0031.102] Setting Ddr voltage to 1125mv [0031.105] Serial Number of Pmic Max77663: 0x1d1ab9 [0031.113] Entering ramdump check [0031.116] Get RamDumpCarveOut = 0x0 [0031.119] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0031.125] Last reboot was clean, booting normally! [0031.129] Sdram initialization is successful [0031.133] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0031.139] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0031.144] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0031.149] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0031.154] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0031.160] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0031.165] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0031.170] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0031.185] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0031.191] Platform-DebugCarveout: 0 [0031.194] Downloaded Bct successfully [0031.297] Downloaded bootloader successfully at 0x92c00000 [0031.398] Downloaded rp1 successfully at 0x83000000 [0031.445] MAX77620_GPIO1 Configured. [0031.449] MAX77620_GPIO5 Configured. [0031.452] CPU power rail is up [0031.455] CPU clock enabled [0031.459] Performing RAM repair [0031.462] Updating A64 Warmreset Address to 0x92c002e9 [0031.468] Enable APE clock/reset [0031.471] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0031.476] Loading Secure OS image failed. [0031.480] Set NvDecSticky Bits [0031.483] GSC1 address : ff700000 [0031.487] GSC2 address ff63fffc value c0edbbcc [0031.491] GSC2 address : ff600000 [0031.495] GSC3 address : ff500000 [0031.499] GSC4 address : ff400000 [0031.503] GSC5 address : ff300000 [0031.506] GSC MC Settings done [0031.509] NvTbootPackSdramParams: start. [0031.514] NvTbootPackSdramParams: done. [0031.518] Next binary entry address: 0x92c00258 [0031.522] BoardId: 2180 [0031.525] dram memory type is 3 [0031.528] Tegraboot started after 30782391 us [0031.532] Basic modules init took -30782391 us [0031.536] USB data transfer took 0 us [0031.540] Carveout took 32281392 us [0031.543] CPU initialization took 3629 us [0031.547] Total time taken by TegraBoot 1502630 us [0031.552] Starting CPU & Halting co-processor [0032.318] [0032.319] Debug Init done [0032.322] Marked DTB cacheable [0032.325] Bootloader DTB loaded at 0x83000000 [0032.329] DeviceTree Init done [0032.343] Pinmux applied successfully [0032.348] gicd_base: 0x50041000 [0032.352] gicc_base: 0x50042000 [0032.355] Interrupts Init done [0032.360] Using base:0x60005008 & irq:33 for tick-timer [0032.365] Using base:0x60005000 for delay-timer [0032.369] platform_init_timer: DONE [0032.373] Timer(tick) Init done [0032.377] osc freq = 38400 khz [0032.382] [0032.383] welcome to cboot [0032.385] [0032.386] Cboot Version: 24.00.2015.42-t210-63d15635 [0032.391] calling constructors [0032.394] initializing heap [0032.397] initializing threads [0032.400] initializing timers [0032.403] creating bootstrap completion thread [0032.407] top of bootstrap2() [0032.410] CPU: ARM Cortex A57 [0032.413] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0032.418] initializing platform [0032.444] config for ddr50 mode completed [0032.448] sdmmc bdev is already initialized [0032.452] of_register: registering tegra_udc to of_hal [0032.457] of_register: registering inv20628-driver to of_hal [0032.463] of_register: registering ads1015-driver to of_hal [0032.468] of_register: registering lp8557-bl-driver to of_hal [0032.474] of_register: registering bq2419x_charger to of_hal [0032.480] of_register: registering cpc to of_hal [0032.484] of_register: registering bq27441_fuel_gauge to of_hal [0032.499] gpio framework initialized [0032.502] of_register: registering tca9539_gpio to of_hal [0032.507] of_register: registering tca9539_gpio to of_hal [0032.513] of_register: registering i2c_bus_driver to of_hal [0032.518] of_register: registering i2c_bus_driver to of_hal [0032.524] of_register: registering i2c_bus_driver to of_hal [0032.529] pmic framework initialized [0032.533] of_register: registering max77620_pmic to of_hal [0032.538] regulator framework initialized [0032.542] of_register: registering tps65132_bl_driver to of_hal [0032.548] of_register: registering tegra_xhci to of_hal [0032.553] initializing target [0032.560] gpio_driver_register: register 'tegra_gpio_driver' driver [0032.570] fixed regulator driver initialized [0032.634] initializing OF layer [0032.639] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0032.647] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0032.669] I2C Bus Init done [0032.672] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0032.683] I2C Bus Init done [0032.686] of_children_init: Ops found for compatible string ti,lp8557 [0032.693] I2C slave not started [0032.695] I2C write failed [0032.698] Writing offset failed [0032.701] failed to read 0x 0 [0032.704] lp8557: Couldn't turn off backlight: -3 [0032.709] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0032.723] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0032.728] gpio_driver_register: register 'tca9539_gpio_driver' driver [0032.734] of_children_init: Ops found for compatible string ti,tca9539 [0032.746] tca9539_init: i2c bus: 2, slave addr: 0xee [0032.751] gpio_driver_register: register 'tca9539_gpio_driver' driver [0032.758] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0032.770] I2C Bus Init done [0032.772] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0032.784] I2C Bus Init done [0032.787] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0032.799] I2C Bus Init done [0032.802] of_children_init: Ops found for compatible string maxim,max77620 [0032.814] max77620_init using irq 118 [0032.819] register 'maxim,max77620' pmic [0032.823] gpio_driver_register: register 'max77620-gpio' driver [0032.830] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0032.842] I2C Bus Init done [0032.844] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0032.853] calling apps_init() [0032.859] Found 19 GPT partitions in "sdmmc3_user" [0032.863] Proceeding to flashing Server [0032.867] usbdcd_reinit Initialize driver to use already enumerated device [0032.874] nv3p_priv_usbf_open USB configuration success [0032.884] Writing GPT partition [0032.888] Erasing Boot device [0032.914] Erasing Storage Device [0033.163] Sanitizing Storage Device [0033.284] Writing protective mbr [0033.288] Writing primary GPT [0033.293] Writing secondary GPT [0033.299] Found 18 GPT partitions in "sdmmc3_user" [0033.306] Writing NVC partition [0033.309] bct_init bctinit [0033.312] bct_init bctinit [0033.322] bct_init bctinit [0033.325] bct_init bctinit [0033.327] bct_init bctinit [0033.361] partition NVC write successful. [0033.367] Writing APP partition [0033.370] bct_init bctinit [0034.426] bct_init bctinit [0034.429] bct_init bctinit [0035.060] partition APP write successful. [0035.067] Writing TBC partition [0035.070] bct_init bctinit [0035.076] bct_init bctinit [0035.079] bct_init bctinit [0035.084] partition TBC write successful. [0035.090] Writing EBT partition [0035.093] bct_init bctinit [0035.118] bct_init bctinit [0035.121] bct_init bctinit [0035.131] partition EBT write successful. [0035.138] Writing BPF partition [0035.140] bct_init bctinit [0035.168] bct_init bctinit [0035.171] bct_init bctinit [0035.178] partition BPF write successful. [0035.184] Writing WB0 partition [0035.187] bct_init bctinit [0035.191] bct_init bctinit [0035.194] bct_init bctinit [0035.198] partition WB0 write successful. [0035.204] Writing RP1 partition [0035.207] bct_init bctinit [0035.228] bct_init bctinit [0035.230] bct_init bctinit [0035.239] partition RP1 write successful. [0035.246] Writing TOS partition [0035.248] bct_init bctinit [0035.255] bct_init bctinit [0035.258] bct_init bctinit [0035.263] partition TOS write successful. [0035.270] Writing DTB partition [0035.272] bct_init bctinit [0035.293] bct_init bctinit [0035.295] bct_init bctinit [0035.305] partition DTB write successful. [0035.316] Writing BCT partition [0035.321] bct_init bctinit [0035.418] partition BCT write successful. [0035.430] Change state to cold boot mode [0035.434] Flushing data to stroage [0000.163] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.168] Processing in cold boot mode Bootloader 2 [0000.173] A02 Bootrom Patch rev = 63 [0000.176] Power-up reason: software reset [0000.180] No Battery Present [0000.183] RamCode = 0 [0000.185] Platform has Ddr4 type ram [0000.188] max77620 disabling SD1 Remote Sense [0000.193] Setting Ddr voltage to 1125mv [0000.197] Serial Number of Pmic Max77663: 0x1d1ab9 [0000.204] Entering ramdump check [0000.207] Get RamDumpCarveOut = 0x0 [0000.211] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.216] Last reboot was clean, booting normally! [0000.220] Sdram initialization is successful [0000.224] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.230] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.235] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.240] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.245] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.250] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.255] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.261] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.276] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.282] Platform-DebugCarveout: 0 [0000.285] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.290] Non secure mode. Disable rollback prevention [0000.295] AOTAG Init Done [0000.322] Using GPT Primary to query partitions [0000.328] Loading Tboot-CPU binary [0000.377] Verifying bootloader in OdmNonSecureSBK mode [0000.386] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.393] Bootloader downloaded successfully. [0000.398] Downloaded Tboot-CPU binary to 0xa0000258 [0000.403] MAX77620_GPIO1 Configured. [0000.406] MAX77620_GPIO5 Configured. [0000.409] CPU power rail is up [0000.412] CPU clock enabled [0000.416] Performing RAM repair [0000.419] Updating A64 Warmreset Address to 0xa00002e9 [0000.436] Bootloader DTB Load Address: 0x83000000 [0000.453] Kernel DTB Load Address: 0x83080000 [0000.458] Loading cboot binary [0000.551] Verifying bootloader in OdmNonSecureSBK mode [0000.657] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.664] Bootloader downloaded successfully. [0000.668] GPT: Partition NOT found ! [0000.672] Find Partition via GPT Failed [0000.675] Find Partition via PT Failed [0000.679] function NvTbootGetBinaryOffsets: 0x1 error [0000.684] Error in NvTbootLoadBinary: 0x1 ! [0000.688] Next binary entry address: 0x80110000 [0000.692] BoardId: 2180 [0000.697] dram memory type is 3 [0000.701] WB0 init successful [0000.727] Bpmp FW successfully loaded [0000.730] Set NvDecSticky Bits [0000.734] GSC1 address : ff700000 [0000.737] GSC2 address ff63fffc value c0edbbcc [0000.742] GSC2 address : ff600000 [0000.745] GSC3 address : ff500000 [0000.749] GSC4 address : ff400000 [0000.753] GSC5 address : ff300000 [0000.756] GSC MC Settings done [0000.760] TOS old plaintext Image length 65536 [0000.766] *** Secure OS image signature not verified *** [0000.771] Loading and Validation of Secure OS Successful [0000.776] NvTbootPackSdramParams: start. [0000.781] NvTbootPackSdramParams: done. [0000.785] Tegraboot started after 142403 us [0000.789] Basic modules init took 292462 us [0000.793] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.799] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.806] Next stage binary read took 12209 us [0000.810] Carveout took 264394 us [0000.813] CPU initialization took 92746 us [0000.817] Total time taken by TegraBoot 661811 us [0000.822] Starting CPU & Halting co-processor 64b[0000.929] RamCode = 0 [0000.944] LPDDR4 Training: Read DT: Number of tables = 10 [0000.950] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.955] EMC Training Skipped [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.963] EMC Training Skipped [0000.965] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.971] EMC Training Skipped [0000.974] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.979] EMC Training Skipped [0000.982] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.988] EMC Training Successful [0000.991] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.997] EMC Training Successful [0001.000] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.011] EMC Training Successful [0001.014] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.037] EMC Training Successful [0001.040] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.061] EMC Training Successful [0001.064] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.084] EMC Training Successful [0001.087] Switching to 800000 KHz Success [0001.093] DT Write: emc-table@40800 succeeded [0001.100] DT Write: emc-table@68000 succeeded [0001.106] DT Write: emc-table@102000 succeeded [0001.112] DT Write: emc-table@204000 succeeded [0001.119] DT Write: emc-table@408000 succeeded [0001.125] DT Write: emc-table@665600 succeeded [0001.132] DT Write: emc-table@800000 succeeded [0001.138] DT Write: emc-table@1065600 succeeded [0001.144] DT Write: emc-table@1331200 succeeded [0001.151] DT Write: emc-table@1600000 succeeded [0001.155] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 þþ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1d1ab9 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99037 us [0000.746] Basic modules init took 292221 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12208 us [0000.768] Carveout took 264390 us [0000.771] CPU initialization took 92747 us [0000.775] Total time taken by TegraBoot 661566 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 65 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915367 bytes read in 213 ms (31 MiB/s) Retrieving file: /boot/Image 17453568 bytes read in 444 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2653/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 61 ms (843.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.444989] console [ttyS0] enabled [ 0.444989] console [ttyS0] enabled [ 0.452388] bootconsole [uart0] disabled [ 0.452388] bootconsole [uart0] disabled [ 0.460905] SuperH (H)SCI(F) driver initialized [ 0.465785] msm_serial: driver initialized [ 0.470348] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.480746] loop: module loaded [ 0.485109] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.496824] max77620-sd0: supplied by regulator-dummy [ 0.503154] max77620-sd1: supplied by regulator-dummy [ 0.509305] max77620-sd2: supplied by regulator-dummy [ 0.515193] max77620-sd3: supplied by regulator-dummy [ 0.521599] max77620-ldo0: supplied by regulator-dummy [ 0.527676] max77620-ldo1: supplied by regulator-dummy [ 0.533407] max77620-ldo2: supplied by regulator-dummy [ 0.539409] max77620-ldo3: supplied by regulator-dummy [ 0.544582] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.551457] max77620-ldo4: supplied by regulator-dummy [ 0.556616] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.563182] max77620-ldo5: supplied by regulator-dummy [ 0.568337] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.575320] max77620-ldo6: supplied by regulator-dummy [ 0.580494] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.587377] max77620-ldo7: supplied by regulator-dummy [ 0.593338] max77620-ldo8: supplied by regulator-dummy [ 0.603939] libphy: Fixed MDIO Bus: probed [ 0.608400] tun: Universal TUN/TAP device driver, 1.6 [ 0.614056] thunder-xcv, ver 1.0 [ 0.617302] thunder-BGX, ver 1.0 [ 0.620563] thunder-nic, ver 1.0 [ 0.624058] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.629886] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.635834] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.642788] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.648391] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.656212] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.662389] sky2: driver version 1.30 [ 0.666344] usbcore: registered new interface driver r8152 [ 0.671936] VFIO - User Level meta-driver version: 0.3 [ 0.677910] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.684436] ehci-pci: EHCI PCI platform driver [ 0.688906] ehci-platform: EHCI generic platform driver [ 0.694232] ehci-orion: EHCI orion driver [ 0.698318] ehci-exynos: EHCI EXYNOS driver [ 0.702572] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.708756] ohci-pci: OHCI PCI platform driver [ 0.713226] ohci-platform: OHCI generic platform driver [ 0.718532] ohci-exynos: OHCI EXYNOS driver [ 0.723264] usbcore: registered new interface driver usb-storage [ 0.862226] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.870457] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.877622] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.883928] i2c /dev entries driver [ 0.890268] sdhci: Secure Digital Host Controller Interface driver [ 0.896445] sdhci: Copyright(c) Pierre Ossman [ 0.900954] Synopsys Designware Multimedia Card Interface Driver [ 0.907570] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.913487] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.933624] mmc0: Unknown controller version (3). You may experience problems. [ 0.971806] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.980727] ledtrig-cpu: registered to indicate activity on CPUs [ 0.987510] usbcore: registered new interface driver usbhid [ 0.993138] usbhid: USB HID core driver [ 0.998654] NET: Registered protocol family 17 [ 1.003175] 9pnet: Installing 9P2000 support [ 1.007482] Key type dns_resolver registered [ 1.012212] registered taskstats version 1 [ 1.016375] Loading compiled-in X.509 certificates [ 1.028797] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.033744] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.039529] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.044822] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.050791] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.057592] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.062786] RTL_5V: supplied by VDD_5V0_SYS [ 1.067198] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.073328] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.078269] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.090991] mmc0: new high speed MMC card at address 0001 [ 1.096946] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.101993] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.108940] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.116091] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.122456] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.128483] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.135235] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.142036] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.151351] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.157777] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.166350] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.173981] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.574993] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.984090] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.393206] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.400703] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.406200] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.414397] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.815980] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.225074] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.634163] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.641659] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.647240] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.653506] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.659685] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.666555] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.673861] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.679801] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.687826] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.697160] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.766248] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.773650] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.779059] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.787613] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.796250] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.802676] hub 1-0:1.0: USB hub found [ 3.806455] hub 1-0:1.0: 5 ports detected [ 3.810806] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.816210] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.823826] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.832233] hub 2-0:1.0: USB hub found [ 3.836008] hub 2-0:1.0: 4 ports detected [ 3.841165] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.854254] mmc1: Unknown controller version (3). You may experience problems. [ 3.893035] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.901176] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.913340] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.921017] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.928296] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.940482] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.969923] max77686-rtc max77620-rtc: setting system clock to 2018-01-19 16:30:48 UTC (1516379448) [ 4.178105] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.204885] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.217564] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.342494] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.402653] r8152 2-1:1.0 eth0: v1.09.9 [ 4.406698] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.418808] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.760202] r8152 2-1:1.0 eth0: carrier on [ 8.781601] IP-Config: Complete: [ 8.784825] device=eth0, hwaddr=00:04:4b:79:75:8d, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.794990] host=192.168.99.2, domain=, nis-domain=(none) [ 8.800817] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.808254] AVDD_DSI_CSI_1V2: disabling [ 8.812105] VDD_PRE_REG_1V35: disabling [ 8.815947] VDD_CAM_HV: disabling [ 8.819400] VDD_TS_HV: disabling [ 8.822754] VDD_TS_1V8: disabling [ 8.826101] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.830473] VDD_3V3_SD: disabling [ 8.833792] VDD_HDMI_5V0: disabling [ 8.837272] ALSA device list: [ 8.840237] No soundcards found. [ 8.844348] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 16:30:53 ] L4T-INITRD Build DATE: Fri Jan 19 16:30:53 UTC 2018 [ 16:30:53 ] Root device found: nfs [ 16:30:53 ] Ethernet interfaces: eth0 [ 16:30:53 ] IP Address: 192.168.99.2 [ 16:30:53 ] Rootfs mounted over nfs [ 16:30:53 ] Switching from initrd to actual rootfs [ 9.474256] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.492598] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.532380] systemd[1]: Set hostname to . [ 9.976727] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.993704] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.009799] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 10.029702] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 10.045816] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 10.061742] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 10.081925] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. Mounting Debug File System... Starting Remount Root and Kernel File Systems... Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Starting Load Kernel Modules... [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on udev Control Socket. Starting Create Static Device Nodes in /dev... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting RPC Pipe File System... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Reached target Local File Systems (Pre). Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started udev Kernel Device Manager. [ 10.767384] systemd-journald[1541]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Raise network interfaces. [ 11.702782] random: crng init done [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting /etc/rc.local Compatibility... Starting Login Service... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started D-Bus System Message Bus. Starting Permit User Sessions... [ OK ] Started Regular background program processing daemon. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting LSB: Start NTP daemon... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. Starting OpenBSD Secure Shell server... Starting System Logging Service... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started Login Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started System Logging Service. [ OK ] Started LSB: Start NTP daemon. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: þþ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1d1ab9 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99042 us [0000.746] Basic modules init took 292253 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12208 us [0000.768] Carveout took 264391 us [0000.771] CPU initialization took 92748 us [0000.775] Total time taken by TegraBoot 661600 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 65 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915367 bytes read in 213 ms (31 MiB/s) Retrieving file: /boot/Image 17453568 bytes read in 444 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2653/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 61 ms (843.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.449715] console [ttyS0] enabled [ 0.449715] console [ttyS0] enabled [ 0.456811] bootconsole [uart0] disabled [ 0.456811] bootconsole [uart0] disabled [ 0.465306] SuperH (H)SCI(F) driver initialized [ 0.470173] msm_serial: driver initialized [ 0.474708] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.485244] loop: module loaded [ 0.489569] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.501272] max77620-sd0: supplied by regulator-dummy [ 0.507628] max77620-sd1: supplied by regulator-dummy [ 0.513772] max77620-sd2: supplied by regulator-dummy [ 0.519661] max77620-sd3: supplied by regulator-dummy [ 0.526073] max77620-ldo0: supplied by regulator-dummy [ 0.532126] max77620-ldo1: supplied by regulator-dummy [ 0.537861] max77620-ldo2: supplied by regulator-dummy [ 0.543880] max77620-ldo3: supplied by regulator-dummy [ 0.549042] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.555913] max77620-ldo4: supplied by regulator-dummy [ 0.561072] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.567628] max77620-ldo5: supplied by regulator-dummy [ 0.572806] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.579797] max77620-ldo6: supplied by regulator-dummy [ 0.584959] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.591835] max77620-ldo7: supplied by regulator-dummy [ 0.597807] max77620-ldo8: supplied by regulator-dummy [ 0.608425] libphy: Fixed MDIO Bus: probed [ 0.612884] tun: Universal TUN/TAP device driver, 1.6 [ 0.618533] thunder-xcv, ver 1.0 [ 0.621797] thunder-BGX, ver 1.0 [ 0.625041] thunder-nic, ver 1.0 [ 0.628526] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.634356] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.640302] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.647257] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.652858] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.660681] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.666858] sky2: driver version 1.30 [ 0.670814] usbcore: registered new interface driver r8152 [ 0.676407] VFIO - User Level meta-driver version: 0.3 [ 0.682396] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.688922] ehci-pci: EHCI PCI platform driver [ 0.693390] ehci-platform: EHCI generic platform driver [ 0.698708] ehci-orion: EHCI orion driver [ 0.702796] ehci-exynos: EHCI EXYNOS driver [ 0.707051] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.713235] ohci-pci: OHCI PCI platform driver [ 0.717721] ohci-platform: OHCI generic platform driver [ 0.723028] ohci-exynos: OHCI EXYNOS driver [ 0.727740] usbcore: registered new interface driver usb-storage [ 0.866659] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.874884] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.882045] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.888357] i2c /dev entries driver [ 0.894677] sdhci: Secure Digital Host Controller Interface driver [ 0.900857] sdhci: Copyright(c) Pierre Ossman [ 0.905368] Synopsys Designware Multimedia Card Interface Driver [ 0.911983] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.917906] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.937721] mmc0: Unknown controller version (3). You may experience problems. [ 0.975899] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.984827] ledtrig-cpu: registered to indicate activity on CPUs [ 0.991697] usbcore: registered new interface driver usbhid [ 0.997326] usbhid: USB HID core driver [ 1.002828] NET: Registered protocol family 17 [ 1.007357] 9pnet: Installing 9P2000 support [ 1.011665] Key type dns_resolver registered [ 1.016436] registered taskstats version 1 [ 1.020603] Loading compiled-in X.509 certificates [ 1.033211] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.038137] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.043920] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.049237] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.055191] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.061902] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.067113] RTL_5V: supplied by VDD_5V0_SYS [ 1.071529] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.077657] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.082623] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.095344] mmc0: new high speed MMC card at address 0001 [ 1.101303] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.106350] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.113268] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.120415] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.126778] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.132798] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.139572] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.146377] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.155672] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.162100] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.170724] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.179075] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.580653] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.989770] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.398870] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.406366] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.411862] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.420054] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.821666] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.230774] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.639885] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.647377] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.652952] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.659220] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.665400] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.672268] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.679574] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.685518] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.693540] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.702894] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.770342] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777743] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.783153] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791693] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.800335] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806781] hub 1-0:1.0: USB hub found [ 3.810560] hub 1-0:1.0: 5 ports detected [ 3.814905] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.820311] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827930] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.836320] hub 2-0:1.0: USB hub found [ 3.840093] hub 2-0:1.0: 4 ports detected [ 3.845244] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.858332] mmc1: Unknown controller version (3). You may experience problems. [ 3.897111] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.905250] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.917424] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.925092] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.932453] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.944589] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.962021] max77686-rtc max77620-rtc: setting system clock to 2018-01-19 16:31:49 UTC (1516379509) [ 4.182197] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.208931] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.221751] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.346591] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.926756] r8152 2-1:1.0 eth0: v1.09.9 [ 4.930807] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.942936] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 9.244267] r8152 2-1:1.0 eth0: carrier on [ 9.273694] IP-Config: Complete: [ 9.276918] device=eth0, hwaddr=00:04:4b:79:75:8d, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 9.287081] host=192.168.99.2, domain=, nis-domain=(none) [ 9.292910] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 9.300333] AVDD_DSI_CSI_1V2: disabling [ 9.304184] VDD_PRE_REG_1V35: disabling [ 9.308025] VDD_CAM_HV: disabling [ 9.311472] VDD_TS_HV: disabling [ 9.314827] VDD_TS_1V8: disabling [ 9.318149] AVDD_SATA_HDMI_DP_1V05: disabling [ 9.322506] VDD_3V3_SD: disabling [ 9.325821] VDD_HDMI_5V0: disabling [ 9.329301] ALSA device list: [ 9.332267] No soundcards found. [ 9.336377] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 16:31:54 ] L4T-INITRD Build DATE: Fri Jan 19 16:31:54 UTC 2018 [ 16:31:54 ] Root device found: nfs [ 16:31:54 ] Ethernet interfaces: eth0 [ 16:31:54 ] IP Address: 192.168.99.2 [ 16:31:54 ] Rootfs mounted over nfs [ 16:31:54 ] Switching from initrd to actual rootfs [ 9.555197] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.573561] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.594656] systemd[1]: Set hostname to . [ 9.854962] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 9.873851] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 9.893740] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 9.910014] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 9.929832] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.945764] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.961860] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting RPC Pipe File System... [ OK ] Created slice system-getty.slice. Starting Create Static Device Nodes in /dev... Starting Load Kernel Modules... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Remount Root and Kernel File Systems... [ OK ] Reached target Slices. [ OK ] Listening on Journal Audit Socket. Mounting Debug File System... [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Syslog Socket. Starting Journal Service... Mounting Huge Pages File System... Mounting POSIX Message Queue File System... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Mounting Configuration File System... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started udev Kernel Device Manager. [ 10.657409] systemd-journald[1540]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. [ OK ] Found device /dev/ttyS0. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt activities. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... Starting Permit User Sessions... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting Login Service... [ OK ] Started D-Bus System Message Bus. [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell ser[ 11.981762] random: crng init done ver. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: