Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 60.07 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 59.82 sec Percent passed so far: 100.0 Final Score: 100.0 [0048.360] Enabled early print [0048.363] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0048.368] Processing in recovery mode [0048.372] A02 Bootrom Patch rev = 63 [0048.375] Power-up reason: pmc por [0048.378] Established communication link with host [0049.346] Odmdata from BCT: 0x00084000 [0049.350] DebugPort= 0x3 [0049.352] BoardId read from EEPROM/NCT: 2180 [0049.380] Turned on fan for loki board [0049.384] Key release before reqd. time for fastboot [0049.388] No Battery Present [0049.391] RamCode = 0 [0049.393] Platform has Ddr4 type ram [0049.397] max77620 disabling SD1 Remote Sense [0049.401] Setting Ddr voltage to 1125mv [0049.405] Serial Number of Pmic Max77663: 0x1711af [0049.413] Entering ramdump check [0049.416] Get RamDumpCarveOut = 0x0 [0049.419] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0049.424] Last reboot was clean, booting normally! [0049.429] Sdram initialization is successful [0049.433] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0049.438] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0049.444] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0049.449] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0049.454] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0049.459] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0049.464] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0049.470] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0049.485] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0049.490] Platform-DebugCarveout: 0 [0049.494] Downloaded Bct successfully [0049.596] Downloaded bootloader successfully at 0x92c00000 [0049.697] Downloaded rp1 successfully at 0x83000000 [0049.775] MAX77620_GPIO1 Configured. [0049.778] MAX77620_GPIO5 Configured. [0049.782] CPU power rail is up [0049.784] CPU clock enabled [0049.788] Performing RAM repair [0049.791] Updating A64 Warmreset Address to 0x92c002e9 [0049.797] Enable APE clock/reset [0049.800] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0049.805] Loading Secure OS image failed. [0049.809] Set NvDecSticky Bits [0049.812] GSC1 address : ff700000 [0049.816] GSC2 address ff63fffc value c0edbbcc [0049.821] GSC2 address : ff600000 [0049.824] GSC3 address : ff500000 [0049.828] GSC4 address : ff400000 [0049.832] GSC5 address : ff300000 [0049.835] GSC MC Settings done [0049.838] NvTbootPackSdramParams: start. [0049.843] NvTbootPackSdramParams: done. [0049.847] Next binary entry address: 0x92c00258 [0049.851] BoardId: 2180 [0049.854] dram memory type is 3 [0049.857] Tegraboot started after 49521237 us [0049.861] Basic modules init took -49521237 us [0049.866] USB data transfer took 0 us [0049.869] Carveout took 51050634 us [0049.873] CPU initialization took 3631 us [0049.876] Total time taken by TegraBoot 1533028 us [0049.881] Starting CPU & Halting co-processor [0051.088] [0051.089] Debug Init done [0051.091] Marked DTB cacheable [0051.094] Bootloader DTB loaded at 0x83000000 [0051.098] DeviceTree Init done [0051.113] Pinmux applied successfully [0051.118] gicd_base: 0x50041000 [0051.122] gicc_base: 0x50042000 [0051.125] Interrupts Init done [0051.129] Using base:0x60005008 & irq:33 for tick-timer [0051.134] Using base:0x60005000 for delay-timer [0051.139] platform_init_timer: DONE [0051.142] Timer(tick) Init done [0051.146] osc freq = 38400 khz [0051.151] [0051.152] welcome to cboot [0051.155] [0051.156] Cboot Version: 24.00.2015.42-t210-63d15635 [0051.161] calling constructors [0051.164] initializing heap [0051.166] initializing threads [0051.169] initializing timers [0051.172] creating bootstrap completion thread [0051.176] top of bootstrap2() [0051.179] CPU: ARM Cortex A57 [0051.182] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0051.187] initializing platform [0051.234] config for ddr50 mode completed [0051.237] sdmmc bdev is already initialized [0051.242] of_register: registering tegra_udc to of_hal [0051.247] of_register: registering inv20628-driver to of_hal [0051.252] of_register: registering ads1015-driver to of_hal [0051.258] of_register: registering lp8557-bl-driver to of_hal [0051.264] of_register: registering bq2419x_charger to of_hal [0051.269] of_register: registering cpc to of_hal [0051.274] of_register: registering bq27441_fuel_gauge to of_hal [0051.288] gpio framework initialized [0051.292] of_register: registering tca9539_gpio to of_hal [0051.297] of_register: registering tca9539_gpio to of_hal [0051.302] of_register: registering i2c_bus_driver to of_hal [0051.308] of_register: registering i2c_bus_driver to of_hal [0051.313] of_register: registering i2c_bus_driver to of_hal [0051.319] pmic framework initialized [0051.323] of_register: registering max77620_pmic to of_hal [0051.328] regulator framework initialized [0051.332] of_register: registering tps65132_bl_driver to of_hal [0051.338] of_register: registering tegra_xhci to of_hal [0051.343] initializing target [0051.350] gpio_driver_register: register 'tegra_gpio_driver' driver [0051.359] fixed regulator driver initialized [0051.424] initializing OF layer [0051.429] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0051.437] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0051.458] I2C Bus Init done [0051.461] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0051.473] I2C Bus Init done [0051.476] of_children_init: Ops found for compatible string ti,lp8557 [0051.482] I2C slave not started [0051.485] I2C write failed [0051.488] Writing offset failed [0051.491] failed to read 0x 0 [0051.494] lp8557: Couldn't turn off backlight: -3 [0051.498] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0051.512] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0051.518] gpio_driver_register: register 'tca9539_gpio_driver' driver [0051.524] of_children_init: Ops found for compatible string ti,tca9539 [0051.535] tca9539_init: i2c bus: 2, slave addr: 0xee [0051.541] gpio_driver_register: register 'tca9539_gpio_driver' driver [0051.547] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0051.559] I2C Bus Init done [0051.562] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0051.574] I2C Bus Init done [0051.576] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0051.589] I2C Bus Init done [0051.591] of_children_init: Ops found for compatible string maxim,max77620 [0051.603] max77620_init using irq 118 [0051.608] register 'maxim,max77620' pmic [0051.613] gpio_driver_register: register 'max77620-gpio' driver [0051.619] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0051.631] I2C Bus Init done [0051.634] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0051.642] calling apps_init() [0051.649] Found 30 GPT partitions in "sdmmc3_user" [0051.653] Proceeding to flashing Server [0051.657] usbdcd_reinit Initialize driver to use already enumerated device [0051.664] nv3p_priv_usbf_open USB configuration success [0051.674] Writing GPT partition [0051.678] Erasing Boot device [0051.704] Erasing Storage Device [0052.864] Sanitizing Storage Device [0053.093] Writing protective mbr [0053.102] Writing primary GPT [0053.107] Writing secondary GPT [0053.113] Found 18 GPT partitions in "sdmmc3_user" [0053.120] Writing NVC partition [0053.123] bct_init bctinit [0053.125] bct_init bctinit [0053.136] bct_init bctinit [0053.139] bct_init bctinit [0053.141] bct_init bctinit [0053.175] partition NVC write successful. [0053.181] Writing APP partition [0053.184] bct_init bctinit [0054.237] bct_init bctinit [0054.239] bct_init bctinit [0054.855] partition APP write successful. [0054.862] Writing TBC partition [0054.865] bct_init bctinit [0054.871] bct_init bctinit [0054.874] bct_init bctinit [0054.879] partition TBC write successful. [0054.885] Writing EBT partition [0054.888] bct_init bctinit [0054.913] bct_init bctinit [0054.915] bct_init bctinit [0054.926] partition EBT write successful. [0054.932] Writing BPF partition [0054.935] bct_init bctinit [0054.958] bct_init bctinit [0054.960] bct_init bctinit [0054.965] partition BPF write successful. [0054.971] Writing WB0 partition [0054.974] bct_init bctinit [0054.978] bct_init bctinit [0054.981] bct_init bctinit [0054.985] partition WB0 write successful. [0054.991] Writing RP1 partition [0054.994] bct_init bctinit [0055.015] bct_init bctinit [0055.018] bct_init bctinit [0055.029] partition RP1 write successful. [0055.035] Writing TOS partition [0055.038] bct_init bctinit [0055.045] bct_init bctinit [0055.047] bct_init bctinit [0055.053] partition TOS write successful. [0055.059] Writing DTB partition [0055.062] bct_init bctinit [0055.083] bct_init bctinit [0055.086] bct_init bctinit [0055.095] partition DTB write successful. [0055.106] Writing BCT partition [0055.111] bct_init bctinit [0055.204] partition BCT write successful. [0055.216] Change state to cold boot mode [0055.220] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.186] Serial Number of Pmic Max77663: 0x1711af [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.447] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.673] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.723] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132034 us [0000.779] Basic modules init took 292474 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12209 us [0000.800] Carveout took 264395 us [0000.803] CPU initialization took 92753 us [0000.807] Total time taken by TegraBoot 661831 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.121] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 [0000.120] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.142] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1711af [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 98987 us [0000.746] Basic modules init took 292229 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12211 us [0000.767] Carveout took 264391 us [0000.771] CPU initialization took 92752 us [0000.775] Total time taken by TegraBoot 661583 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915391 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17318400 bytes read in 440 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2763/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 52 ms (989.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.439134] console [ttyS0] enabled [ 0.439134] console [ttyS0] enabled [ 0.446227] bootconsole [uart0] disabled [ 0.446227] bootconsole [uart0] disabled [ 0.454662] SuperH (H)SCI(F) driver initialized [ 0.459525] msm_serial: driver initialized [ 0.464073] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.474294] loop: module loaded [ 0.478623] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.490350] max77620-sd0: supplied by regulator-dummy [ 0.496673] max77620-sd1: supplied by regulator-dummy [ 0.502832] max77620-sd2: supplied by regulator-dummy [ 0.508721] max77620-sd3: supplied by regulator-dummy [ 0.515106] max77620-ldo0: supplied by regulator-dummy [ 0.521186] max77620-ldo1: supplied by regulator-dummy [ 0.526915] max77620-ldo2: supplied by regulator-dummy [ 0.532918] max77620-ldo3: supplied by regulator-dummy [ 0.538074] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.544962] max77620-ldo4: supplied by regulator-dummy [ 0.550115] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.556689] max77620-ldo5: supplied by regulator-dummy [ 0.561845] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.568829] max77620-ldo6: supplied by regulator-dummy [ 0.573988] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.580891] max77620-ldo7: supplied by regulator-dummy [ 0.586862] max77620-ldo8: supplied by regulator-dummy [ 0.597445] libphy: Fixed MDIO Bus: probed [ 0.601847] tun: Universal TUN/TAP device driver, 1.6 [ 0.607454] thunder-xcv, ver 1.0 [ 0.610718] thunder-BGX, ver 1.0 [ 0.613972] thunder-nic, ver 1.0 [ 0.617452] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.623280] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.629225] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.636180] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.641777] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.649598] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.655770] sky2: driver version 1.30 [ 0.659723] usbcore: registered new interface driver r8152 [ 0.665323] VFIO - User Level meta-driver version: 0.3 [ 0.671278] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.677809] ehci-pci: EHCI PCI platform driver [ 0.682274] ehci-platform: EHCI generic platform driver [ 0.687594] ehci-orion: EHCI orion driver [ 0.691675] ehci-exynos: EHCI EXYNOS driver [ 0.695931] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.702112] ohci-pci: OHCI PCI platform driver [ 0.706582] ohci-platform: OHCI generic platform driver [ 0.711885] ohci-exynos: OHCI EXYNOS driver [ 0.716589] usbcore: registered new interface driver usb-storage [ 0.855418] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.863628] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.870804] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.877112] i2c /dev entries driver [ 0.883367] sdhci: Secure Digital Host Controller Interface driver [ 0.889547] sdhci: Copyright(c) Pierre Ossman [ 0.894058] Synopsys Designware Multimedia Card Interface Driver [ 0.900651] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.906563] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.927801] mmc0: Unknown controller version (3). You may experience problems. [ 0.965973] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.974898] ledtrig-cpu: registered to indicate activity on CPUs [ 0.981719] usbcore: registered new interface driver usbhid [ 0.987341] usbhid: USB HID core driver [ 0.992785] NET: Registered protocol family 17 [ 0.997309] 9pnet: Installing 9P2000 support [ 1.001619] Key type dns_resolver registered [ 1.006353] registered taskstats version 1 [ 1.010478] Loading compiled-in X.509 certificates [ 1.022999] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.027942] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.033725] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.039020] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.044943] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.051668] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.056907] RTL_5V: supplied by VDD_5V0_SYS [ 1.061309] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.067409] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.072350] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.085449] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.092440] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.099235] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.106034] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.113541] mmc0: new high speed MMC card at address 0001 [ 1.119489] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.124500] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.130860] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.136919] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.144581] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.151257] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.158294] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.166048] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.567604] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.976687] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.385771] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.393271] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.398770] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.406965] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.808527] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.217599] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.626667] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.634163] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.639736] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.646005] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.652186] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.659056] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.666361] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.672317] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.680372] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.689706] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.757527] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.764931] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.770344] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.778879] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.787519] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.793943] hub 1-0:1.0: USB hub found [ 3.797723] hub 1-0:1.0: 5 ports detected [ 3.802064] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.807471] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.815092] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.823487] hub 2-0:1.0: USB hub found [ 3.827263] hub 2-0:1.0: 4 ports detected [ 3.832414] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.845511] mmc1: Unknown controller version (3). You may experience problems. [ 3.884365] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.892506] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.904672] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.912335] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.919436] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.931566] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.951958] max77686-rtc max77620-rtc: setting system clock to 2018-01-09 06:11:18 UTC (1515478278) [ 4.169381] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.196020] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.208652] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.333768] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.393935] r8152 2-1:1.0 eth0: v1.09.9 [ 4.397982] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.410096] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.863451] r8152 2-1:1.0 eth0: carrier on [ 8.892877] IP-Config: Complete: [ 8.896100] device=eth0, hwaddr=00:04:4b:66:e1:7f, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.906264] host=192.168.99.2, domain=, nis-domain=(none) [ 8.912092] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.919512] AVDD_DSI_CSI_1V2: disabling [ 8.923361] VDD_PRE_REG_1V35: disabling [ 8.927200] VDD_CAM_HV: disabling [ 8.930655] VDD_TS_HV: disabling [ 8.934009] VDD_TS_1V8: disabling [ 8.937330] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.941688] VDD_3V3_SD: disabling [ 8.945003] VDD_HDMI_5V0: disabling [ 8.948483] ALSA device list: [ 8.951448] No soundcards found. [ 8.955550] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 06:11:23 ] L4T-INITRD Build DATE: Tue Jan 9 06:11:23 UTC 2018 [ 06:11:23 ] Root device found: nfs [ 06:11:23 ] Ethernet interfaces: eth0 [ 06:11:23 ] IP Address: 192.168.99.2 [ 06:11:23 ] Rootfs mounted over nfs [ 06:11:23 ] Switching from initrd to actual rootfs [ 9.663748] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.682170] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.714380] systemd[1]: Set hostname to . [ 10.820375] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 10.841092] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 10.856931] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 10.873054] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 10.892978] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 10.912977] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.928923] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Syslog Socket. [ OK ] Listening on udev Control Socket. [ OK ] Created slice System Slice. Mounting POSIX Message Queue File System... [ OK ] Created slice system-serial\x2dgetty.slice. Starting Create Static Device Nodes in /dev... [ OK ] Created slice system-getty.slice. Mounting Huge Pages File System... Mounting RPC Pipe File System... Starting Journal Service... Mounting Debug File System... [ OK ] Started Dispatch Password Requests to Console Directory Watch. Starting Load Kernel Modules... [ OK ] Reached target Paths. [ 11.307414] random: crng init done Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ OK ] Started Load Kernel Modules. Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... [ OK ] Mounted Configuration File System. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ 12.219054] systemd-journald[1534]: Received request to flush runtime journal from PID 1 [ OK ] Started Apply Kernel Variables. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Preprocess NFS configuration. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Permit User Sessions... Starting Login Service... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started D-Bus System Message Bus. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/ttyS0. [ 21.162069] print_req_error: I/O error, dev mmcblk0, sector 512 [ 21.964436] print_req_error: I/O error, dev mmcblk0, sector 29359650 [ 21.995494] print_req_error: I/O error, dev mmcblk0, sector 29589666 [ 22.003709] print_req_error: I/O error, dev mmcblk0, sector 29417634 [ 22.012195] print_req_error: I/O error, dev mmcblk0, sector 29458594 [ 22.073527] print_req_error: I/O error, dev mmcblk0, sector 29590050 [ 22.088621] print_req_error: I/O error, dev mmcblk0, sector 30776354 [ 22.118014] print_req_error: I/O error, dev mmcblk0, sector 29588514 [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Raise network interfaces. [* ] A start job is running for Login Service (21s / 1min 35s) [** ] A start job is running for Login Service (22s / 1min 35s) [*** ] A start job is running for Login Service (23s / 1min 35s) [ *** ] A start job is running for Login Service (23s / 1min 35s) [ *** ] A start job is running for Login Service (24s / 1min 35s) [ ***] A start job is running for Login Service (25s / 1min 35s) [ **] A start job is running for Login Service (25s / 1min 35s) [ *] A start job is running for Login Service (26s / 1min 35s) [ **] A start job is running for Login Service (27s / 1min 35s) [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Login Service. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: [0000.120] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.142] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1711af [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 98984 us [0000.746] Basic modules init took 292232 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12209 us [0000.767] Carveout took 264391 us [0000.771] CPU initialization took 92752 us [0000.775] Total time taken by TegraBoot 661584 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915391 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17318400 bytes read in 440 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2763/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 52 ms (989.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.441759] console [ttyS0] enabled [ 0.441759] console [ttyS0] enabled [ 0.448862] bootconsole [uart0] disabled [ 0.448862] bootconsole [uart0] disabled [ 0.457423] SuperH (H)SCI(F) driver initialized [ 0.462257] msm_serial: driver initialized [ 0.466776] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.477070] loop: module loaded [ 0.481407] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.493071] max77620-sd0: supplied by regulator-dummy [ 0.499420] max77620-sd1: supplied by regulator-dummy [ 0.505545] max77620-sd2: supplied by regulator-dummy [ 0.511439] max77620-sd3: supplied by regulator-dummy [ 0.517849] max77620-ldo0: supplied by regulator-dummy [ 0.523910] max77620-ldo1: supplied by regulator-dummy [ 0.529630] max77620-ldo2: supplied by regulator-dummy [ 0.535650] max77620-ldo3: supplied by regulator-dummy [ 0.540811] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.547682] max77620-ldo4: supplied by regulator-dummy [ 0.552852] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.559417] max77620-ldo5: supplied by regulator-dummy [ 0.564576] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.571574] max77620-ldo6: supplied by regulator-dummy [ 0.576729] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.583611] max77620-ldo7: supplied by regulator-dummy [ 0.589576] max77620-ldo8: supplied by regulator-dummy [ 0.600145] libphy: Fixed MDIO Bus: probed [ 0.604625] tun: Universal TUN/TAP device driver, 1.6 [ 0.610222] thunder-xcv, ver 1.0 [ 0.613483] thunder-BGX, ver 1.0 [ 0.616728] thunder-nic, ver 1.0 [ 0.620204] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.626033] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.631984] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.638938] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.644534] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.652356] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.658527] sky2: driver version 1.30 [ 0.662481] usbcore: registered new interface driver r8152 [ 0.668075] VFIO - User Level meta-driver version: 0.3 [ 0.674027] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.680554] ehci-pci: EHCI PCI platform driver [ 0.685022] ehci-platform: EHCI generic platform driver [ 0.690341] ehci-orion: EHCI orion driver [ 0.694424] ehci-exynos: EHCI EXYNOS driver [ 0.698679] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.704860] ohci-pci: OHCI PCI platform driver [ 0.709329] ohci-platform: OHCI generic platform driver [ 0.714635] ohci-exynos: OHCI EXYNOS driver [ 0.719338] usbcore: registered new interface driver usb-storage [ 0.858195] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.866433] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.873591] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.879896] i2c /dev entries driver [ 0.886162] sdhci: Secure Digital Host Controller Interface driver [ 0.892340] sdhci: Copyright(c) Pierre Ossman [ 0.896857] Synopsys Designware Multimedia Card Interface Driver [ 0.903464] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.909376] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.928875] mmc0: Unknown controller version (3). You may experience problems. [ 0.967044] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.975970] ledtrig-cpu: registered to indicate activity on CPUs [ 0.982872] usbcore: registered new interface driver usbhid [ 0.988450] usbhid: USB HID core driver [ 0.993851] NET: Registered protocol family 17 [ 0.998361] 9pnet: Installing 9P2000 support [ 1.002644] Key type dns_resolver registered [ 1.007367] registered taskstats version 1 [ 1.011465] Loading compiled-in X.509 certificates [ 1.016067] mmc0: new high speed MMC card at address 0001 [ 1.016621] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.017095] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.017542] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.017651] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.023413] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.060287] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.065208] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.070954] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.076264] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.082200] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.088883] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.094087] RTL_5V: supplied by VDD_5V0_SYS [ 1.098494] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.104575] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.109506] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.122492] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.129406] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.136175] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.142926] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.151221] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.157983] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.166191] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.567736] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.976801] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.385874] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.393371] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.398864] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.407057] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.808594] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.217655] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.626712] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.634208] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.639782] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.646053] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.652233] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.659102] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.666408] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.672255] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.680162] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.689494] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.757500] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.764902] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.770313] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.778872] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.787508] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.793931] hub 1-0:1.0: USB hub found [ 3.797707] hub 1-0:1.0: 5 ports detected [ 3.802051] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.807455] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.815072] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.823460] hub 2-0:1.0: USB hub found [ 3.827235] hub 2-0:1.0: 4 ports detected [ 3.832370] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.845454] mmc1: Unknown controller version (3). You may experience problems. [ 3.884242] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.892380] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.904518] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.912185] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.919412] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.931586] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.957169] max77686-rtc max77620-rtc: setting system clock to 2018-01-09 06:12:27 UTC (1515478347) [ 4.165352] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.192090] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.204871] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.329746] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.401921] r8152 2-1:1.0 eth0: v1.09.9 [ 4.405964] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.418054] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.607455] r8152 2-1:1.0 eth0: carrier on [ 8.636851] IP-Config: Complete: [ 8.640096] device=eth0, hwaddr=00:04:4b:66:e1:7f, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.650260] host=192.168.99.2, domain=, nis-domain=(none) [ 8.656088] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.663511] AVDD_DSI_CSI_1V2: disabling [ 8.667360] VDD_PRE_REG_1V35: disabling [ 8.671227] VDD_CAM_HV: disabling [ 8.674675] VDD_TS_HV: disabling [ 8.678030] VDD_TS_1V8: disabling [ 8.681351] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.685708] VDD_3V3_SD: disabling [ 8.689023] VDD_HDMI_5V0: disabling [ 8.692503] ALSA device list: [ 8.695468] No soundcards found. [ 8.699584] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 06:12:32 ] L4T-INITRD Build DATE: Tue Jan 9 06:12:32 UTC 2018 [ 06:12:32 ] Root device found: nfs [ 06:12:32 ] Ethernet interfaces: eth0 [ 06:12:32 ] IP Address: 192.168.99.2 [ 06:12:32 ] Rootfs mounted over nfs [ 06:12:32 ] Switching from initrd to actual rootfs [ 8.933064] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.951410] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.969824] systemd[1]: Set hostname to . [ 9.720340] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.736944] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.753089] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 9.769062] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 9.793010] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 9.812893] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 9.829162] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice System Slice. Mounting RPC Pipe File System... [ OK ] Created slice system-getty.slice. [ OK ] Reached target Slices. Starting Remount Root and Kernel File Systems... Mounting Huge Pages File System... Mounting POSIX Message Queue File System... [ OK ] Listening on Syslog Socket. Starting Journal Service... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on udev Control Socket. Mounting Debug File System... Starting Load Kernel Modules... Starting Create Static Device Nodes in /dev... [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK [ 10.367055] random: crng init done ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Load/Save Random Seed. [ OK ] Started Preprocess NFS configuration. [ OK ] Reached target NFS client services. [ 11.091152] systemd-journald[1534]: Received request to flush runtime journal from PID 1 [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting Login Service... [ OK ] Started D-Bus System Message Bus. [ 17.544571] print_req_error: I/O error, dev mmcblk0, sector 512 [ 17.569600] print_req_error: I/O error, dev mmcblk0, sector 30776440 [ 17.585340] print_req_error: I/O error, dev mmcblk0, sector 30776952 Starting System Logging Service... Starting Permit User Sessions... [ OK ] Started Regular background program processing daemon. [ 18.394877] WARNING: CPU: 0 PID: 2555 at block/blk-merge.c:513 blk_rq_map_sg+0x524/0x550 [ 18.402956] Modules linked in: [ 18.406010] CPU: 0 PID: 2555 Comm: kworker/0:2H Not tainted 4.15.0-rc7-next-20180109-225900-g06d4186 #1 [ 18.415383] Hardware name: NVIDIA Jetson TX1 Developer Kit (DT) [ 18.421296] Workqueue: kblockd blk_mq_run_work_fn [ 18.425992] pstate: 20000005 (nzCv daif -PAN -UAO) [ 18.430772] pc : blk_rq_map_sg+0x524/0x550 [ 18.434860] lr : blk_rq_map_sg+0x1f0/0x550 [ 18.438945] sp : ffff00000d7539e0 [ 18.442249] x29: ffff00000d7539e0 x28: ffff8000f95490c0 [ 18.447553] x27: ffff8000f7c307f0 x26: 0000000000000000 [ 18.452855] x25: 0000000000000007 x24: ffff8000f9533900 [ 18.458158] x23: 0000000000000000 x22: ffff8000f95490c0 [ 18.463460] x21: 0000000000000fff x20: 0000000000000040 [ 18.468761] x19: 0000000000000000 x18: 0000ffffd46f29a8 [ 18.474063] x17: 0000ffff8e044268 x16: ffff000008213cd4 [ 18.479364] x15: 0000000000000001 x14: 0000000000000424 [ 18.484665] x13: ffff0000098d5120 x12: 0000000000001000 [ 18.489967] x11: 0000000000000040 x10: 0000000000000008 [ 18.495268] x9 : 0000000000000000 x8 : ffff8000f9533bd0 [ 18.500570] x7 : 0000000000001000 x6 : 0000000000001000 [ 18.505870] x5 : 0000000000001000 x4 : 0000000000000000 [ 18.511171] x3 : 0000000000001000 x2 : 0000000000000000 [ 18.516472] x1 : 0000000000002082 x0 : 0000000000000006 [ 18.521774] Call trace: [ 18.524214] blk_rq_map_sg+0x524/0x550 [ 18.527958] mmc_queue_map_sg+0x1c/0x24 [ 18.531785] mmc_blk_data_prep+0x180/0x2d0 [ 18.535871] mmc_blk_rw_rq_prep+0x48/0x198 [ 18.539956] mmc_blk_mq_issue_rq+0x3d0/0x750 [ 18.544215] mmc_mq_queue_rq+0x130/0x218 [ 18.548128] blk_mq_dispatch_rq_list+0x1b0/0x534 [ 18.552736] blk_mq_do_dispatch_sched+0x80/0x10c [ 18.557342] blk_mq_sched_dispatch_requests+0x138/0x1c4 [ 18.562557] __blk_mq_run_hw_queue+0x98/0xec [ 18.566816] blk_mq_run_work_fn+0x50/0x64 [ 18.570819] process_one_work+0x124/0x290 [ 18.574820] worker_thread+0x13c/0x3f8 [ 18.578561] kthread+0xfc/0x128 [ 18.581697] ret_from_fork+0x10/0x18 [ 18.585263] ---[ end trace 617a4f1d896b03bf ]--- [ 18.590337] print_req_error: I/O error, dev mmcblk0, sector 29719586 [ 18.601969] print_req_error: I/O error, dev mmcblk0, sector 29458594 [ 18.614023] print_req_error: I/O error, dev mmcblk0, sector 162 [ 18.622778] print_req_error: I/O error, dev mmcblk0, sector 29417634 [ 18.661874] print_req_error: I/O error, dev mmcblk0, sector 29761698 [ 18.705638] print_req_error: I/O error, dev mmcblk0, sector 29458978 [ 18.713981] WARNING: CPU: 0 PID: 2555 at block/blk-merge.c:513 blk_rq_map_sg+0x524/0x550 [ 18.722057] Modules linked in: [ 18.725112] CPU: 0 PID: 2555 Comm: kworker/0:2H Tainted: G W 4.15.0-rc7-next-20180109-225900-g06d4186 #1 [ 18.735785] Hardware name: NVIDIA Jetson TX1 Developer Kit (DT) [ 18.741697] Workqueue: kblockd blk_mq_run_work_fn [ 18.746395] pstate: 20000005 (nzCv daif -PAN -UAO) [ 18.751175] pc : blk_rq_map_sg+0x524/0x550 [ 18.755261] lr : blk_rq_map_sg+0x1f0/0x550 [ 18.759346] sp : ffff00000d7539e0 [ 18.762650] x29: ffff00000d7539e0 x28: ffff8000f95040c0 [ 18.767954] x27: ffff8000f7dc13f0 x26: 0000000000000000 [ 18.773256] x25: 0000000000000007 x24: ffff8000f94d9900 [ 18.778558] x23: 0000000000000000 x22: ffff8000f95040c0 [ 18.783860] x21: 0000000000000fff x20: 0000000000000040 [ 18.789161] x19: 0000000000000000 x18: 0000000000008090 [ 18.794463] x17: 0000000000000000 x16: ffff000008212e68 [ 18.799764] x15: 0000000000000001 x14: 0000000000000424 [ 18.805066] x13: ffff0000098d5130 x12: 0000000000001000 [ 18.810367] x11: 0000000179038000 x10: 0000000000000008 [ 18.815668] x9 : 0000000000000000 x8 : ffff8000f94d9bd0 [ 18.820969] x7 : 0000000000001000 x6 : 0000000000001000 [ 18.826272] x5 : 0000000000001000 x4 : 0000000000000000 [ 18.831573] x3 : 0000000000001000 x2 : 0000000000000000 [ 18.836874] x1 : 0000000000002082 x0 : 0000000000000006 [ 18.842175] Call trace: [ 18.844615] blk_rq_map_sg+0x524/0x550 [ 18.848358] mmc_queue_map_sg+0x1c/0x24 [ 18.852185] mmc_blk_data_prep+0x180/0x2d0 [ 18.856272] mmc_blk_rw_rq_prep+0x48/0x198 [ 18.860359] mmc_blk_mq_issue_rq+0x3d0/0x750 [ 18.864618] mmc_mq_queue_rq+0x130/0x218 [ 18.868532] blk_mq_dispatch_rq_list+0x1b0/0x534 [ 18.873140] blk_mq_do_dispatch_sched+0x80/0x10c [ 18.877746] blk_mq_sched_dispatch_requests+0x138/0x1c4 [ 18.882960] __blk_mq_run_hw_queue+0x98/0xec [ 18.887219] blk_mq_run_work_fn+0x50/0x64 [ 18.891221] process_one_work+0x124/0x290 [ 18.895221] worker_thread+0x13c/0x3f8 [ 18.898961] kthread+0xfc/0x128 [ 18.902096] ret_from_fork+0x10/0x18 [ 18.905662] ---[ end trace 617a4f1d896b03c0 ]--- [ 18.910541] print_req_error: I/O error, dev mmcblk0, sector 546 [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/ttyS0. [ OK ] Started System Logging Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Raise network interfaces. [* ] A start job is running for Login Service (20s / 1min 35s) [** ] A start job is running for Login Service (22s / 1min 35s) [*** ] A start job is running for Login Service (22s / 1min 35s) [ *** ] A start job is running for Login Service (23s / 1min 35s) [ *** ] A start job is running for Login Service (23s / 1min 35s) [ ***] A start job is running for Login Service (24s / 1min 35s) [ **] A start job is running for Login Service (25s / 1min 35s) [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... [ OK ] Reached target Network is Online. Starting /etc/rc.local Compatibility... Starting LSB: Start NTP daemon... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Login Service. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: