Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 60.12 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 59.91 sec Percent passed so far: 100.0 Final Score: 100.0 |[0023.184] Enabled early print [0023.187] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0023.193] Processing in recovery mode [0023.196] A02 Bootrom Patch rev = 63 [0023.199] Power-up reason: pmc por [0023.203] Established communication link with host [0024.167] Odmdata from BCT: 0x00084000 [0024.171] DebugPort= 0x3 [0024.173] BoardId read from EEPROM/NCT: 2180 [0024.201] Turned on fan for loki board [0024.205] Key release before reqd. time for fastboot [0024.209] No Battery Present [0024.212] RamCode = 0 [0024.214] Platform has Ddr4 type ram [0024.218] max77620 disabling SD1 Remote Sense [0024.222] Setting Ddr voltage to 1125mv [0024.226] Serial Number of Pmic Max77663: 0x1200a3 [0024.234] Entering ramdump check [0024.237] Get RamDumpCarveOut = 0x0 [0024.240] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0024.245] Last reboot was clean, booting normally! [0024.250] Sdram initialization is successful [0024.254] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0024.259] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0024.264] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0024.270] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0024.275] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0024.280] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0024.285] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0024.290] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0024.306] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0024.311] Platform-DebugCarveout: 0 [0024.314] Downloaded Bct successfully [0024.409] Downloaded bootloader successfully at 0x92c00000 [0024.502] Downloaded rp1 successfully at 0x83000000 [0024.551] MAX77620_GPIO1 Configured. [0024.554] MAX77620_GPIO5 Configured. [0024.558] CPU power rail is up [0024.561] CPU clock enabled [0024.565] Performing RAM repair [0024.568] Updating A64 Warmreset Address to 0x92c002e9 [0024.574] Enable APE clock/reset [0024.577] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0024.581] Loading Secure OS image failed. [0024.585] Set NvDecSticky Bits [0024.589] GSC1 address : ff700000 [0024.592] GSC2 address ff63fffc value c0edbbcc [0024.597] GSC2 address : ff600000 [0024.601] GSC3 address : ff500000 [0024.604] GSC4 address : ff400000 [0024.608] GSC5 address : ff300000 [0024.611] GSC MC Settings done [0024.614] NvTbootPackSdramParams: start. [0024.619] NvTbootPackSdramParams: done. [0024.623] Next binary entry address: 0x92c00258 [0024.628] BoardId: 2180 [0024.630] dram memory type is 3 [0024.633] Tegraboot started after 23741182 us [0024.638] Basic modules init took -23741182 us [0024.642] USB data transfer took 0 us [0024.645] Carveout took 25221433 us [0024.649] CPU initialization took 3628 us [0024.653] Total time taken by TegraBoot 1483879 us [0024.657] Starting CPU & Halting co-processor [0025.258] [0025.259] Debug Init done [0025.262] Marked DTB cacheable [0025.265] Bootloader DTB loaded at 0x83000000 [0025.269] DeviceTree Init done [0025.283] Pinmux applied successfully [0025.288] gicd_base: 0x50041000 [0025.292] gicc_base: 0x50042000 [0025.295] Interrupts Init done [0025.300] Using base:0x60005008 & irq:33 for tick-timer [0025.305] Using base:0x60005000 for delay-timer [0025.309] platform_init_timer: DONE [0025.313] Timer(tick) Init done [0025.317] osc freq = 38400 khz [0025.322] [0025.323] welcome to cboot [0025.325] [0025.326] Cboot Version: 24.00.2015.42-t210-63d15635 [0025.331] calling constructors [0025.334] initializing heap [0025.337] initializing threads [0025.340] initializing timers [0025.343] creating bootstrap completion thread [0025.347] top of bootstrap2() [0025.350] CPU: ARM Cortex A57 [0025.353] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0025.358] initializing platform [0025.394] config for ddr50 mode completed [0025.398] sdmmc bdev is already initialized [0025.402] of_register: registering tegra_udc to of_hal [0025.407] of_register: registering inv20628-driver to of_hal [0025.413] of_register: registering ads1015-driver to of_hal [0025.418] of_register: registering lp8557-bl-driver to of_hal [0025.424] of_register: registering bq2419x_charger to of_hal [0025.430] of_register: registering cpc to of_hal [0025.434] of_register: registering bq27441_fuel_gauge to of_hal [0025.449] gpio framework initialized [0025.452] of_register: registering tca9539_gpio to of_hal [0025.457] of_register: registering tca9539_gpio to of_hal [0025.463] of_register: registering i2c_bus_driver to of_hal [0025.468] of_register: registering i2c_bus_driver to of_hal [0025.474] of_register: registering i2c_bus_driver to of_hal [0025.480] pmic framework initialized [0025.483] of_register: registering max77620_pmic to of_hal [0025.488] regulator framework initialized [0025.492] of_register: registering tps65132_bl_driver to of_hal [0025.498] of_register: registering tegra_xhci to of_hal [0025.504] initializing target [0025.510] gpio_driver_register: register 'tegra_gpio_driver' driver [0025.520] fixed regulator driver initialized [0025.585] initializing OF layer [0025.589] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0025.597] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0025.619] I2C Bus Init done [0025.622] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0025.634] I2C Bus Init done [0025.636] of_children_init: Ops found for compatible string ti,lp8557 [0025.643] I2C slave not started [0025.646] I2C write failed [0025.648] Writing offset failed [0025.651] failed to read 0x 0 [0025.654] lp8557: Couldn't turn off backlight: -3 [0025.659] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0025.673] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0025.678] gpio_driver_register: register 'tca9539_gpio_driver' driver [0025.685] of_children_init: Ops found for compatible string ti,tca9539 [0025.696] tca9539_init: i2c bus: 2, slave addr: 0xee [0025.701] gpio_driver_register: register 'tca9539_gpio_driver' driver [0025.708] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0025.720] I2C Bus Init done [0025.722] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0025.734] I2C Bus Init done [0025.737] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0025.749] I2C Bus Init done [0025.752] of_children_init: Ops found for compatible string maxim,max77620 [0025.764] max77620_init using irq 118 [0025.769] register 'maxim,max77620' pmic [0025.773] gpio_driver_register: register 'max77620-gpio' driver [0025.780] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0025.792] I2C Bus Init done [0025.794] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0025.803] calling apps_init() [0025.809] Found 30 GPT partitions in "sdmmc3_user" [0025.814] Proceeding to flashing Server [0025.818] usbdcd_reinit Initialize driver to use already enumerated device [0025.825] nv3p_priv_usbf_open USB configuration success [0025.831] Writing GPT partition [0025.835] Erasing Boot device [0025.861] Erasing Storage Device [0026.767] Sanitizing Storage Device [0026.911] Writing protective mbr [0026.915] Writing primary GPT [0026.921] Writing secondary GPT [0026.926] Found 18 GPT partitions in "sdmmc3_user" [0026.932] Writing NVC partition [0026.935] bct_init bctinit [0026.938] bct_init bctinit [0026.946] bct_init bctinit [0026.948] bct_init bctinit [0026.951] bct_init bctinit [0026.985] partition NVC write successful. [0026.989] Writing APP partition [0026.992] bct_init bctinit [0027.816] bct_init bctinit [0027.819] bct_init bctinit [0028.447] partition APP write successful. [0028.452] Writing TBC partition [0028.455] bct_init bctinit [0028.460] bct_init bctinit [0028.463] bct_init bctinit [0028.468] partition TBC write successful. [0028.473] Writing EBT partition [0028.476] bct_init bctinit [0028.495] bct_init bctinit [0028.497] bct_init bctinit [0028.508] partition EBT write successful. [0028.513] Writing BPF partition [0028.516] bct_init bctinit [0028.537] bct_init bctinit [0028.540] bct_init bctinit [0028.545] partition BPF write successful. [0028.550] Writing WB0 partition [0028.553] bct_init bctinit [0028.556] bct_init bctinit [0028.559] bct_init bctinit [0028.563] partition WB0 write successful. [0028.568] Writing RP1 partition [0028.571] bct_init bctinit [0028.586] bct_init bctinit [0028.589] bct_init bctinit [0028.598] partition RP1 write successful. [0028.603] Writing TOS partition [0028.606] bct_init bctinit [0028.611] bct_init bctinit [0028.614] bct_init bctinit [0028.620] partition TOS write successful. [0028.624] Writing DTB partition [0028.627] bct_init bctinit [0028.643] bct_init bctinit [0028.645] bct_init bctinit [0028.655] partition DTB write successful. [0028.662] Writing BCT partition [0028.666] bct_init bctinit [0028.761] partition BCT write successful. [0028.769] Change state to cold boot mode [0028.773] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.159] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.179] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0x1200a3 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.201] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.246] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.272] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.318] Loading Tboot-CPU binary [0000.367] Verifying bootloader in OdmNonSecureSBK mode [0000.377] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.384] Bootloader downloaded successfully. [0000.388] Downloaded Tboot-CPU binary to 0xa0000258 [0000.393] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.400] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.542] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.678] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.736] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132312 us [0000.779] Basic modules init took 292469 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12211 us [0000.800] Carveout took 264397 us [0000.803] CPU initialization took 92752 us [0000.807] Total time taken by TegraBoot 661829 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.935] LPDDR4 Training: Read DT: Number of tables = 10 [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.956] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.964] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.052] EMC Training Successful [0001.055] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.103] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2 øø[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1200a3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99274 us [0000.746] Basic modules init took 292242 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12211 us [0000.768] Carveout took 264397 us [0000.771] CPU initialization took 92756 us [0000.775] Total time taken by TegraBoot 661606 us [0000.780] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915800 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17318400 bytes read in 440 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11019/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.454222] console [ttyS0] enabled [ 0.454222] console [ttyS0] enabled [ 0.461318] bootconsole [uart0] disabled [ 0.461318] bootconsole [uart0] disabled [ 0.469804] SuperH (H)SCI(F) driver initialized [ 0.474691] msm_serial: driver initialized [ 0.479217] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.489647] loop: module loaded [ 0.493979] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.505699] max77620-sd0: supplied by regulator-dummy [ 0.512047] max77620-sd1: supplied by regulator-dummy [ 0.518184] max77620-sd2: supplied by regulator-dummy [ 0.524065] max77620-sd3: supplied by regulator-dummy [ 0.530483] max77620-ldo0: supplied by regulator-dummy [ 0.536540] max77620-ldo1: supplied by regulator-dummy [ 0.542276] max77620-ldo2: supplied by regulator-dummy [ 0.548287] max77620-ldo3: supplied by regulator-dummy [ 0.553450] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.560313] max77620-ldo4: supplied by regulator-dummy [ 0.565471] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.572034] max77620-ldo5: supplied by regulator-dummy [ 0.577208] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.584195] max77620-ldo6: supplied by regulator-dummy [ 0.589353] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.596235] max77620-ldo7: supplied by regulator-dummy [ 0.602212] max77620-ldo8: supplied by regulator-dummy [ 0.612783] libphy: Fixed MDIO Bus: probed [ 0.617280] tun: Universal TUN/TAP device driver, 1.6 [ 0.622869] thunder-xcv, ver 1.0 [ 0.626119] thunder-BGX, ver 1.0 [ 0.629379] thunder-nic, ver 1.0 [ 0.632860] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.638691] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.644632] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.651590] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.657185] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.665007] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.671174] sky2: driver version 1.30 [ 0.675121] usbcore: registered new interface driver r8152 [ 0.680695] VFIO - User Level meta-driver version: 0.3 [ 0.686644] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.693172] ehci-pci: EHCI PCI platform driver [ 0.697639] ehci-platform: EHCI generic platform driver [ 0.702955] ehci-orion: EHCI orion driver [ 0.707040] ehci-exynos: EHCI EXYNOS driver [ 0.711295] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.717477] ohci-pci: OHCI PCI platform driver [ 0.721948] ohci-platform: OHCI generic platform driver [ 0.727248] ohci-exynos: OHCI EXYNOS driver [ 0.731951] usbcore: registered new interface driver usb-storage [ 0.870771] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.879010] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.886165] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.892476] i2c /dev entries driver [ 0.898739] sdhci: Secure Digital Host Controller Interface driver [ 0.904915] sdhci: Copyright(c) Pierre Ossman [ 0.909424] Synopsys Designware Multimedia Card Interface Driver [ 0.916019] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.921924] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.942248] mmc0: Unknown controller version (3). You may experience problems. [ 0.978830] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.987734] ledtrig-cpu: registered to indicate activity on CPUs [ 0.994510] usbcore: registered new interface driver usbhid [ 1.000081] usbhid: USB HID core driver [ 1.005467] NET: Registered protocol family 17 [ 1.010011] 9pnet: Installing 9P2000 support [ 1.014302] Key type dns_resolver registered [ 1.019020] registered taskstats version 1 [ 1.023122] Loading compiled-in X.509 certificates [ 1.025919] mmc0: new high speed MMC card at address 0001 [ 1.026481] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.026911] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.027357] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.027468] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.033236] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.072143] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.077074] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.082867] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.088163] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.094085] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.100774] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.105964] RTL_5V: supplied by VDD_5V0_SYS [ 1.110402] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.116494] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.121392] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.134385] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.141310] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.148064] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.154818] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.163113] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.169858] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.178064] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.579639] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.988711] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.397793] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.405288] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.410781] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.418974] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.820547] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.229625] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.638706] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.646198] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.651764] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.658031] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.664212] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.671081] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.678385] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.684223] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.692269] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.701599] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.770869] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.778269] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.783678] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.792236] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.800873] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.807274] hub 1-0:1.0: USB hub found [ 3.811050] hub 1-0:1.0: 5 ports detected [ 3.815393] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.820796] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.828416] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.836799] hub 2-0:1.0: USB hub found [ 3.840576] hub 2-0:1.0: 4 ports detected [ 3.845709] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.858816] mmc1: Unknown controller version (3). You may experience problems. [ 3.897687] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.905832] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.917979] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.925637] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.932662] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.944803] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.962560] max77686-rtc max77620-rtc: setting system clock to 2018-01-05 06:03:03 UTC (1515132183) [ 4.182724] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.209371] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.221807] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.355110] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.415276] r8152 2-1:1.0 eth0: v1.09.9 [ 4.419323] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.431428] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.292816] r8152 2-1:1.0 eth0: carrier on [ 7.318223] IP-Config: Complete: [ 7.321446] device=eth0, hwaddr=00:04:4b:79:99:b3, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.331633] host=192.168.99.2, domain=, nis-domain=(none) [ 7.337462] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.344879] AVDD_DSI_CSI_1V2: disabling [ 7.348730] VDD_PRE_REG_1V35: disabling [ 7.352572] VDD_CAM_HV: disabling [ 7.356043] VDD_TS_HV: disabling [ 7.359402] VDD_TS_1V8: disabling [ 7.362723] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.367080] VDD_3V3_SD: disabling [ 7.370395] VDD_HDMI_5V0: disabling [ 7.373875] ALSA device list: [ 7.376841] No soundcards found. [ 7.380968] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 06:03:06 ] L4T-INITRD Build DATE: Fri Jan 5 06:03:06 UTC 2018 [ 06:03:06 ] Root device found: nfs [ 06:03:06 ] Ethernet interfaces: eth0 [ 06:03:06 ] IP Address: 192.168.99.2 [ 06:03:06 ] Rootfs mounted over nfs [ 06:03:06 ] Switching from initrd to actual rootfs [ 8.041058] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.059397] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.094487] systemd[1]: Set hostname to . [ 9.134234] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.150353] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 9.166371] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 9.186388] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 9.206273] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 9.222549] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 9.242318] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Audit Socket. [ OK ] Created slice System Slice. Mounting RPC Pipe File System... Mounting Debug File System... Mounting Huge Pages File System... Starting Create Static Device Nodes in /dev... Starting Remount Root and Kernel File Systems... [ OK ] Listening on udev Control Socket. [ OK ] Created slice system-getty.slice. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ 9.612406] random: crng init done Starting Load Kernel Modules... [ OK ] Reached target Swap. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... Mounting POSIX Message Queue File System... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Reached target Slices. [ OK ] Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. Starting Apply Kernel Variables... Mounting Configuration File System... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Flush Journal to Persistent Storage... [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. Starting Raise network interfaces... [ 10.672566] systemd-journald[1540]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Preprocess NFS configuration. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started D-Bus System Message Bus. Starting Login Service... [ OK ] Started Daily Cleanup of Temporary Directories. Starting Permit User Sessions... Starting System Logging Service... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/ttyS0. [ OK ] Started System Logging Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Raise network interfaces. [* ] A start job is running for Login Service (20s / 1min 37s) [** ] A start job is running for Login Service (21s / 1min 37s) [*** ] A start job is running for Login Service (22s / 1min 37s) [ *** ] A start job is running for Login Service (23s / 1min 37s) [ *** ] A start job is running for Login Service (24s / 1min 37s) [ ***] A start job is running for Login Service (24s / 1min 37s) [ **] A start job is running for Login Service (25s / 1min 37s) [ *] A start job is running for Login Service (26s / 1min 37s) [ **] A start job is running for Login Service (26s / 1min 37s) [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... [ OK ] Reached target Network is Online. Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... [ OK ] Started Login Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: üö[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x1200a3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99319 us [0000.746] Basic modules init took 292229 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12211 us [0000.768] Carveout took 264394 us [0000.771] CPU initialization took 92751 us [0000.775] Total time taken by TegraBoot 661585 us [0000.780] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.096] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.113] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915800 bytes read in 216 ms (30.5 MiB/s) Retrieving file: /boot/Image 17318400 bytes read in 440 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11019/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.450302] console [ttyS0] enabled [ 0.450302] console [ttyS0] enabled [ 0.457911] bootconsole [uart0] disabled [ 0.457911] bootconsole [uart0] disabled [ 0.466602] SuperH (H)SCI(F) driver initialized [ 0.471458] msm_serial: driver initialized [ 0.475979] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.486226] loop: module loaded [ 0.490624] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.502279] max77620-sd0: supplied by regulator-dummy [ 0.508596] max77620-sd1: supplied by regulator-dummy [ 0.514756] max77620-sd2: supplied by regulator-dummy [ 0.520637] max77620-sd3: supplied by regulator-dummy [ 0.527021] max77620-ldo0: supplied by regulator-dummy [ 0.533105] max77620-ldo1: supplied by regulator-dummy [ 0.538840] max77620-ldo2: supplied by regulator-dummy [ 0.544841] max77620-ldo3: supplied by regulator-dummy [ 0.550001] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.556894] max77620-ldo4: supplied by regulator-dummy [ 0.562050] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.568617] max77620-ldo5: supplied by regulator-dummy [ 0.573775] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.580762] max77620-ldo6: supplied by regulator-dummy [ 0.585922] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.592824] max77620-ldo7: supplied by regulator-dummy [ 0.598798] max77620-ldo8: supplied by regulator-dummy [ 0.609324] libphy: Fixed MDIO Bus: probed [ 0.613769] tun: Universal TUN/TAP device driver, 1.6 [ 0.619363] thunder-xcv, ver 1.0 [ 0.622613] thunder-BGX, ver 1.0 [ 0.625874] thunder-nic, ver 1.0 [ 0.629345] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.635175] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.641125] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.648080] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.653675] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.661495] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.667665] sky2: driver version 1.30 [ 0.671610] usbcore: registered new interface driver r8152 [ 0.677193] VFIO - User Level meta-driver version: 0.3 [ 0.683146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.689670] ehci-pci: EHCI PCI platform driver [ 0.694135] ehci-platform: EHCI generic platform driver [ 0.699451] ehci-orion: EHCI orion driver [ 0.703533] ehci-exynos: EHCI EXYNOS driver [ 0.707784] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.713968] ohci-pci: OHCI PCI platform driver [ 0.718436] ohci-platform: OHCI generic platform driver [ 0.723743] ohci-exynos: OHCI EXYNOS driver [ 0.728442] usbcore: registered new interface driver usb-storage [ 0.867410] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.875624] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.882784] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.889091] i2c /dev entries driver [ 0.895332] sdhci: Secure Digital Host Controller Interface driver [ 0.901509] sdhci: Copyright(c) Pierre Ossman [ 0.906018] Synopsys Designware Multimedia Card Interface Driver [ 0.912605] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.918519] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.938781] mmc0: Unknown controller version (3). You may experience problems. [ 0.977062] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.986119] ledtrig-cpu: registered to indicate activity on CPUs [ 0.992962] usbcore: registered new interface driver usbhid [ 0.998538] usbhid: USB HID core driver [ 1.003952] NET: Registered protocol family 17 [ 1.008455] 9pnet: Installing 9P2000 support [ 1.012735] Key type dns_resolver registered [ 1.017451] registered taskstats version 1 [ 1.021550] Loading compiled-in X.509 certificates [ 1.026032] mmc0: new high speed MMC card at address 0001 [ 1.026595] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.027051] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.027483] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.027594] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.028761] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.070490] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.075419] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.081168] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.086483] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.092410] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.099101] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.104314] RTL_5V: supplied by VDD_5V0_SYS [ 1.108723] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.114805] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.119729] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.132710] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.139616] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.146373] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.153144] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.161441] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.168193] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.176399] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.577985] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.987087] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.396162] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.403657] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.409148] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.417340] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.818922] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.228005] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.637071] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.644565] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.650136] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.656404] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.662585] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.669454] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.676760] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.682606] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.690637] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.699968] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.767401] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.774803] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.780214] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.788745] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.797379] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.803811] hub 1-0:1.0: USB hub found [ 3.807590] hub 1-0:1.0: 5 ports detected [ 3.811940] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.817345] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.824971] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.833357] hub 2-0:1.0: USB hub found [ 3.837132] hub 2-0:1.0: 4 ports detected [ 3.842262] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.855353] mmc1: Unknown controller version (3). You may experience problems. [ 3.894112] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.902250] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.914378] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.922042] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.929275] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.941444] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.971079] max77686-rtc max77620-rtc: setting system clock to 2018-01-05 06:04:13 UTC (1515132253) [ 4.175257] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.201933] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.214677] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.339648] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.399815] r8152 2-1:1.0 eth0: v1.09.9 [ 4.403870] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.415982] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.289328] r8152 2-1:1.0 eth0: carrier on [ 7.318756] IP-Config: Complete: [ 7.321979] device=eth0, hwaddr=00:04:4b:79:99:b3, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.332144] host=192.168.99.2, domain=, nis-domain=(none) [ 7.337972] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.345402] AVDD_DSI_CSI_1V2: disabling [ 7.349252] VDD_PRE_REG_1V35: disabling [ 7.353092] VDD_CAM_HV: disabling [ 7.356540] VDD_TS_HV: disabling [ 7.359898] VDD_TS_1V8: disabling [ 7.363219] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.367576] VDD_3V3_SD: disabling [ 7.370891] VDD_HDMI_5V0: disabling [ 7.374372] ALSA device list: [ 7.377336] No soundcards found. [ 7.381454] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 06:04:16 ] L4T-INITRD Build DATE: Fri Jan 5 06:04:16 UTC 2018 [ 06:04:16 ] Root device found: nfs [ 06:04:16 ] Ethernet interfaces: eth0 [ 06:04:16 ] IP Address: 192.168.99.2 [ 06:04:16 ] Rootfs mounted over nfs [ 06:04:16 ] Switching from initrd to actual rootfs [ 7.616871] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.635222] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.655656] systemd[1]: Set hostname to . [ 8.370950] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.390835] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.406973] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 8.422930] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 8.446853] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.462881] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 8.483068] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Syslog Socket. [ OK ] Created slice system-getty.slice. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on udev Control Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Starting Create Static Device Nodes in /dev... Mounting RPC Pipe File System... Mounting POSIX Message Queue File System... Mounting Huge Pages File System... Mounting Debug File System... Starting Journal Service... Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ 9.045486] random: crng init done [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted Debug File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. Starting Raise network interfaces... [ 9.822402] systemd-journald[1533]: Received request to flush runtime journal from PID 1 [ OK ] Started Preprocess NFS configuration. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting Login Service... Starting System Logging Service... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Started D-Bus System Message Bus. [ OK ] Started Regular background program processing daemon. Starting Permit User Sessions... [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/ttyS0. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Raise network interfaces. [* ] A start job is running for Login Service (20s / 1min 34s) [** ] A start job is running for Login Service (21s / 1min 34s) [*** ] A start job is running for Login Service (22s / 1min 34s) [ *** ] A start job is running for Login Service (23s / 1min 34s) [ *** ] A start job is running for Login Service (24s / 1min 34s) [ ***] A start job is running for Login Service (24s / 1min 34s) [ **] A start job is running for Login Service (25s / 1min 34s) [ *] A start job is running for Login Service (26s / 1min 34s) [ **] A start job is running for Login Service (26s / 1min 34s) [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting LSB: Start NTP daemon... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Login Service. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ø