Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.23 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.89 sec Percent passed so far: 100.0 Final Score: 100.0 è[0033.155] Enabled early print [0033.158] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0033.163] Processing in recovery mode [0033.166] A02 Bootrom Patch rev = 63 [0033.170] Power-up reason: pmc por [0033.173] Established communication link with host [0034.141] Odmdata from BCT: 0x00084000 [0034.144] DebugPort= 0x3 [0034.147] BoardId read from EEPROM/NCT: 2180 [0034.175] Turned on fan for loki board [0034.178] Key release before reqd. time for fastboot [0034.183] No Battery Present [0034.186] RamCode = 0 [0034.188] Platform has Ddr4 type ram [0034.191] max77620 disabling SD1 Remote Sense [0034.196] Setting Ddr voltage to 1125mv [0034.200] Serial Number of Pmic Max77663: 0x2608a3 [0034.207] Entering ramdump check [0034.210] Get RamDumpCarveOut = 0x0 [0034.214] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0034.219] Last reboot was clean, booting normally! [0034.223] Sdram initialization is successful [0034.227] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0034.233] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0034.238] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0034.243] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0034.248] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0034.254] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0034.259] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0034.264] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0034.279] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0034.285] Platform-DebugCarveout: 0 [0034.288] Downloaded Bct successfully [0034.391] Downloaded bootloader successfully at 0x92c00000 [0034.491] Downloaded rp1 successfully at 0x83000000 [0034.538] MAX77620_GPIO1 Configured. [0034.542] MAX77620_GPIO5 Configured. [0034.545] CPU power rail is up [0034.548] CPU clock enabled [0034.552] Performing RAM repair [0034.555] Updating A64 Warmreset Address to 0x92c002e9 [0034.561] Enable APE clock/reset [0034.564] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0034.569] Loading Secure OS image failed. [0034.573] Set NvDecSticky Bits [0034.576] GSC1 address : ff700000 [0034.580] GSC2 address ff63fffc value c0edbbcc [0034.584] GSC2 address : ff600000 [0034.588] GSC3 address : ff500000 [0034.592] GSC4 address : ff400000 [0034.596] GSC5 address : ff300000 [0034.599] GSC MC Settings done [0034.602] NvTbootPackSdramParams: start. [0034.607] NvTbootPackSdramParams: done. [0034.611] Next binary entry address: 0x92c00258 [0034.615] BoardId: 2180 [0034.618] dram memory type is 3 [0034.621] Tegraboot started after 33950897 us [0034.625] Basic modules init took -33950897 us [0034.630] USB data transfer took 0 us [0034.633] Carveout took 35448744 us [0034.636] CPU initialization took 3630 us [0034.640] Total time taken by TegraBoot 1501477 us [0034.645] Starting CPU & Halting co-processor [0035.486] [0035.487] Debug Init done [0035.489] Marked DTB cacheable [0035.492] Bootloader DTB loaded at 0x83000000 [0035.497] DeviceTree Init done [0035.511] Pinmux applied successfully [0035.516] gicd_base: 0x50041000 [0035.520] gicc_base: 0x50042000 [0035.523] Interrupts Init done [0035.527] Using base:0x60005008 & irq:33 for tick-timer [0035.532] Using base:0x60005000 for delay-timer [0035.537] platform_init_timer: DONE [0035.540] Timer(tick) Init done [0035.544] osc freq = 38400 khz [0035.549] [0035.550] welcome to cboot [0035.553] [0035.554] Cboot Version: 24.00.2015.42-t210-63d15635 [0035.559] calling constructors [0035.562] initializing heap [0035.564] initializing threads [0035.567] initializing timers [0035.570] creating bootstrap completion thread [0035.575] top of bootstrap2() [0035.577] CPU: ARM Cortex A57 [0035.580] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0035.585] initializing platform [0035.611] config for ddr50 mode completed [0035.615] sdmmc bdev is already initialized [0035.619] of_register: registering tegra_udc to of_hal [0035.624] of_register: registering inv20628-driver to of_hal [0035.630] of_register: registering ads1015-driver to of_hal [0035.636] of_register: registering lp8557-bl-driver to of_hal [0035.641] of_register: registering bq2419x_charger to of_hal [0035.647] of_register: registering cpc to of_hal [0035.652] of_register: registering bq27441_fuel_gauge to of_hal [0035.666] gpio framework initialized [0035.669] of_register: registering tca9539_gpio to of_hal [0035.675] of_register: registering tca9539_gpio to of_hal [0035.680] of_register: registering i2c_bus_driver to of_hal [0035.686] of_register: registering i2c_bus_driver to of_hal [0035.691] of_register: registering i2c_bus_driver to of_hal [0035.697] pmic framework initialized [0035.700] of_register: registering max77620_pmic to of_hal [0035.706] regulator framework initialized [0035.710] of_register: registering tps65132_bl_driver to of_hal [0035.715] of_register: registering tegra_xhci to of_hal [0035.721] initializing target [0035.727] gpio_driver_register: register 'tegra_gpio_driver' driver [0035.737] fixed regulator driver initialized [0035.802] initializing OF layer [0035.806] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0035.814] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.836] I2C Bus Init done [0035.839] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.851] I2C Bus Init done [0035.853] of_children_init: Ops found for compatible string ti,lp8557 [0035.860] I2C slave not started [0035.863] I2C write failed [0035.865] Writing offset failed [0035.868] failed to read 0x 0 [0035.871] lp8557: Couldn't turn off backlight: -3 [0035.876] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0035.890] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0035.895] gpio_driver_register: register 'tca9539_gpio_driver' driver [0035.902] of_children_init: Ops found for compatible string ti,tca9539 [0035.913] tca9539_init: i2c bus: 2, slave addr: 0xee [0035.918] gpio_driver_register: register 'tca9539_gpio_driver' driver [0035.925] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.937] I2C Bus Init done [0035.939] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.951] I2C Bus Init done [0035.954] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0035.966] I2C Bus Init done [0035.969] of_children_init: Ops found for compatible string maxim,max77620 [0035.981] max77620_init using irq 118 [0035.986] register 'maxim,max77620' pmic [0035.990] gpio_driver_register: register 'max77620-gpio' driver [0035.997] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0036.009] I2C Bus Init done [0036.012] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0036.020] calling apps_init() [0036.025] Found 19 GPT partitions in "sdmmc3_user" [0036.030] Proceeding to flashing Server [0036.034] usbdcd_reinit Initialize driver to use already enumerated device [0036.041] nv3p_priv_usbf_open USB configuration success [0036.050] Writing GPT partition [0036.055] Erasing Boot device [0036.081] Erasing Storage Device [0036.330] Sanitizing Storage Device [0036.454] Writing protective mbr [0036.458] Writing primary GPT [0036.463] Writing secondary GPT [0036.469] Found 18 GPT partitions in "sdmmc3_user" [0036.476] Writing NVC partition [0036.479] bct_init bctinit [0036.482] bct_init bctinit [0036.492] bct_init bctinit [0036.495] bct_init bctinit [0036.498] bct_init bctinit [0036.531] partition NVC write successful. [0036.537] Writing APP partition [0036.540] bct_init bctinit [0037.720] bct_init bctinit [0037.722] bct_init bctinit [0038.322] partition APP write successful. [0038.329] Writing TBC partition [0038.331] bct_init bctinit [0038.338] bct_init bctinit [0038.341] bct_init bctinit [0038.346] partition TBC write successful. [0038.352] Writing EBT partition [0038.355] bct_init bctinit [0038.379] bct_init bctinit [0038.382] bct_init bctinit [0038.395] partition EBT write successful. [0038.401] Writing BPF partition [0038.404] bct_init bctinit [0038.430] bct_init bctinit [0038.432] bct_init bctinit [0038.437] partition BPF write successful. [0038.443] Writing WB0 partition [0038.446] bct_init bctinit [0038.451] bct_init bctinit [0038.453] bct_init bctinit [0038.457] partition WB0 write successful. [0038.463] Writing RP1 partition [0038.466] bct_init bctinit [0038.487] bct_init bctinit [0038.490] bct_init bctinit [0038.499] partition RP1 write successful. [0038.505] Writing TOS partition [0038.508] bct_init bctinit [0038.515] bct_init bctinit [0038.517] bct_init bctinit [0038.523] partition TOS write successful. [0038.529] Writing DTB partition [0038.532] bct_init bctinit [0038.552] bct_init bctinit [0038.555] bct_init bctinit [0038.564] partition DTB write successful. [0038.576] Writing BCT partition [0038.581] bct_init bctinit [0038.674] partition BCT write successful. [0038.686] Change state to cold boot mode [0038.690] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.186] Serial Number of Pmic Max77663: 0x2608a3 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.447] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.673] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.723] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132075 us [0000.779] Basic modules init took 292431 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12205 us [0000.800] Carveout took 264380 us [0000.803] CPU initialization took 92728 us [0000.807] Total time taken by TegraBoot 661744 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.121] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 ð¨[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x2608a3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99028 us [0000.746] Basic modules init took 292221 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12205 us [0000.767] Carveout took 264373 us [0000.771] CPU initialization took 92731 us [0000.775] Total time taken by TegraBoot 661530 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915475 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17115648 bytes read in 436 ms (37.4 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2674/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 52 ms (989.3 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.450827] console [ttyS0] enabled [ 0.450827] console [ttyS0] enabled [ 0.457919] bootconsole [uart0] disabled [ 0.457919] bootconsole [uart0] disabled [ 0.466377] SuperH (H)SCI(F) driver initialized [ 0.471211] msm_serial: driver initialized [ 0.475747] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.486073] loop: module loaded [ 0.490379] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.502110] max77620-sd0: supplied by regulator-dummy [ 0.508441] max77620-sd1: supplied by regulator-dummy [ 0.514570] max77620-sd2: supplied by regulator-dummy [ 0.520475] max77620-sd3: supplied by regulator-dummy [ 0.526870] max77620-ldo0: supplied by regulator-dummy [ 0.532931] max77620-ldo1: supplied by regulator-dummy [ 0.538677] max77620-ldo2: supplied by regulator-dummy [ 0.544678] max77620-ldo3: supplied by regulator-dummy [ 0.549838] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.556704] max77620-ldo4: supplied by regulator-dummy [ 0.561881] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.568453] max77620-ldo5: supplied by regulator-dummy [ 0.573614] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.580595] max77620-ldo6: supplied by regulator-dummy [ 0.585753] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.592630] max77620-ldo7: supplied by regulator-dummy [ 0.598618] max77620-ldo8: supplied by regulator-dummy [ 0.609073] libphy: Fixed MDIO Bus: probed [ 0.613554] tun: Universal TUN/TAP device driver, 1.6 [ 0.619148] thunder-xcv, ver 1.0 [ 0.622407] thunder-BGX, ver 1.0 [ 0.625667] thunder-nic, ver 1.0 [ 0.629138] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.634964] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.640913] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.647867] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.653469] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.661290] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.667473] sky2: driver version 1.30 [ 0.671413] usbcore: registered new interface driver r8152 [ 0.676996] VFIO - User Level meta-driver version: 0.3 [ 0.682931] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.689458] ehci-pci: EHCI PCI platform driver [ 0.693923] ehci-platform: EHCI generic platform driver [ 0.699232] ehci-orion: EHCI orion driver [ 0.703312] ehci-exynos: EHCI EXYNOS driver [ 0.707564] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.713748] ohci-pci: OHCI PCI platform driver [ 0.718221] ohci-platform: OHCI generic platform driver [ 0.723525] ohci-exynos: OHCI EXYNOS driver [ 0.728225] usbcore: registered new interface driver usb-storage [ 0.867102] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.875306] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.882465] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.888772] i2c /dev entries driver [ 0.895022] sdhci: Secure Digital Host Controller Interface driver [ 0.901202] sdhci: Copyright(c) Pierre Ossman [ 0.905711] Synopsys Designware Multimedia Card Interface Driver [ 0.912315] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.918234] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.939492] mmc0: Unknown controller version (3). You may experience problems. [ 0.977150] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.986073] ledtrig-cpu: registered to indicate activity on CPUs [ 0.992901] usbcore: registered new interface driver usbhid [ 0.998528] usbhid: USB HID core driver [ 1.003914] NET: Registered protocol family 17 [ 1.008482] 9pnet: Installing 9P2000 support [ 1.012797] Key type dns_resolver registered [ 1.017609] registered taskstats version 1 [ 1.021746] Loading compiled-in X.509 certificates [ 1.033148] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.038085] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.043837] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.049147] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.055078] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.061781] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.064153] mmc0: new high speed MMC card at address 0001 [ 1.064700] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.065177] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.065627] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.065751] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.067465] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.103881] RTL_5V: supplied by VDD_5V0_SYS [ 1.108307] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.114417] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.119327] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.132342] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.139279] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.146034] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.152786] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.161066] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.167806] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.176009] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.577500] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.986518] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.395519] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.403013] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.408504] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.416695] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.818181] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.227178] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.636184] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.643675] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.649245] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.655512] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.661690] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.668562] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.675867] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.681691] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.689715] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.699049] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.769766] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777166] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.782576] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791129] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.799763] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806181] hub 1-0:1.0: USB hub found [ 3.809959] hub 1-0:1.0: 5 ports detected [ 3.814296] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.819698] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827320] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.835712] hub 2-0:1.0: USB hub found [ 3.839483] hub 2-0:1.0: 4 ports detected [ 3.844621] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.857720] mmc1: Unknown controller version (3). You may experience problems. [ 3.896571] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.904710] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.916821] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.924492] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.931745] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.943938] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.973437] max77686-rtc max77620-rtc: setting system clock to 2017-12-19 09:59:46 UTC (1513677586) [ 4.177622] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.204300] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.216906] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.342008] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.402171] r8152 2-1:1.0 eth0: v1.09.9 [ 4.406208] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.418303] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.827726] r8152 2-1:1.0 eth0: carrier on [ 8.853117] IP-Config: Complete: [ 8.856340] device=eth0, hwaddr=00:04:4b:79:97:49, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.866505] host=192.168.99.2, domain=, nis-domain=(none) [ 8.872332] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.879760] AVDD_DSI_CSI_1V2: disabling [ 8.883611] VDD_PRE_REG_1V35: disabling [ 8.887451] VDD_CAM_HV: disabling [ 8.890895] VDD_TS_HV: disabling [ 8.894251] VDD_TS_1V8: disabling [ 8.897571] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.901928] VDD_3V3_SD: disabling [ 8.905243] VDD_HDMI_5V0: disabling [ 8.908722] ALSA device list: [ 8.911686] No soundcards found. [ 8.915805] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 09:59:51 ] L4T-INITRD Build DATE: Tue Dec 19 09:59:51 UTC 2017 [ 09:59:51 ] Root device found: nfs [ 09:59:51 ] Ethernet interfaces: eth0 [ 09:59:51 ] IP Address: 192.168.99.2 [ 09:59:51 ] Rootfs mounted over nfs [ 09:59:51 ] Switching from initrd to actual rootfs [ 9.699167] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.717520] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.778788] systemd[1]: Set hostname to . [ 10.314805] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 10.333291] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 10.349171] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 10.365211] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.381167] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.397234] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 10.413226] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Reached target Slices. [ OK ] Listening on Journal Socket. Starting Remount Root and Kernel File Systems... Mounting RPC Pipe File System... Starting Create Static Device Nodes in /dev... Mounting POSIX Message Queue File System... Mounting Debug File System... [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Audit Socket. Starting Journal Service... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. Mounting Huge Pages File System... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Load Kernel Modules... [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Starting Load/Save Random Seed... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ 11.123125] systemd-journald[1531]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Volatile Files and Directories. [ OK ] Found device /dev/ttyS0. [ 12.047212] random: crng init done [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting System Logging Service... Starting OpenBSD Secure Shell server... Starting /etc/rc.local Compatibility... [ OK ] Started D-Bus System Message Bus. Starting Permit User Sessions... Starting Login Service... Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started Regular background program processing daemon. [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: øª[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x2608a3 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.713] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99033 us [0000.746] Basic modules init took 292212 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12205 us [0000.767] Carveout took 264373 us [0000.771] CPU initialization took 92729 us [0000.774] Total time taken by TegraBoot 661519 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915475 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17115648 bytes read in 436 ms (37.4 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl2674/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52710 bytes read in 53 ms (970.7 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fde5 Starting kernel ... [ 0.453477] console [ttyS0] enabled [ 0.453477] console [ttyS0] enabled [ 0.460578] bootconsole [uart0] disabled [ 0.460578] bootconsole [uart0] disabled [ 0.469094] SuperH (H)SCI(F) driver initialized [ 0.473937] msm_serial: driver initialized [ 0.478451] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.488722] loop: module loaded [ 0.493066] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.504779] max77620-sd0: supplied by regulator-dummy [ 0.511103] max77620-sd1: supplied by regulator-dummy [ 0.517238] max77620-sd2: supplied by regulator-dummy [ 0.523141] max77620-sd3: supplied by regulator-dummy [ 0.529542] max77620-ldo0: supplied by regulator-dummy [ 0.535598] max77620-ldo1: supplied by regulator-dummy [ 0.541359] max77620-ldo2: supplied by regulator-dummy [ 0.547353] max77620-ldo3: supplied by regulator-dummy [ 0.552509] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.559385] max77620-ldo4: supplied by regulator-dummy [ 0.564540] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.571123] max77620-ldo5: supplied by regulator-dummy [ 0.576279] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.583266] max77620-ldo6: supplied by regulator-dummy [ 0.588425] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.595309] max77620-ldo7: supplied by regulator-dummy [ 0.601284] max77620-ldo8: supplied by regulator-dummy [ 0.611776] libphy: Fixed MDIO Bus: probed [ 0.616235] tun: Universal TUN/TAP device driver, 1.6 [ 0.621817] thunder-xcv, ver 1.0 [ 0.625082] thunder-BGX, ver 1.0 [ 0.628327] thunder-nic, ver 1.0 [ 0.631798] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.637629] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.643574] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.650532] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.656129] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.663952] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.670123] sky2: driver version 1.30 [ 0.674067] usbcore: registered new interface driver r8152 [ 0.679646] VFIO - User Level meta-driver version: 0.3 [ 0.685611] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692136] ehci-pci: EHCI PCI platform driver [ 0.696603] ehci-platform: EHCI generic platform driver [ 0.701919] ehci-orion: EHCI orion driver [ 0.705998] ehci-exynos: EHCI EXYNOS driver [ 0.710254] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.716437] ohci-pci: OHCI PCI platform driver [ 0.720903] ohci-platform: OHCI generic platform driver [ 0.726217] ohci-exynos: OHCI EXYNOS driver [ 0.730914] usbcore: registered new interface driver usb-storage [ 0.869831] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.878045] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.885204] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.891507] i2c /dev entries driver [ 0.897750] sdhci: Secure Digital Host Controller Interface driver [ 0.903930] sdhci: Copyright(c) Pierre Ossman [ 0.908441] Synopsys Designware Multimedia Card Interface Driver [ 0.915037] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.920946] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.941089] mmc0: Unknown controller version (3). You may experience problems. [ 0.979375] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 0.988300] ledtrig-cpu: registered to indicate activity on CPUs [ 0.995170] usbcore: registered new interface driver usbhid [ 1.000801] usbhid: USB HID core driver [ 1.006163] NET: Registered protocol family 17 [ 1.010722] 9pnet: Installing 9P2000 support [ 1.015010] Key type dns_resolver registered [ 1.019706] registered taskstats version 1 [ 1.023807] Loading compiled-in X.509 certificates [ 1.035178] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.040110] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.045874] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.051166] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.052788] mmc0: new high speed MMC card at address 0001 [ 1.053369] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.053807] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.054250] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.054370] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.056073] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.094031] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.100739] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.105935] RTL_5V: supplied by VDD_5V0_SYS [ 1.110371] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.116451] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.121363] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.134375] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.141294] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.148052] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.154800] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.163075] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.169836] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.178039] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.579540] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.988552] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.397575] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.405068] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.410560] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.418754] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.820276] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.229282] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.638284] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.645777] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.651348] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.657615] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.663795] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.670663] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.677969] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.683793] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.691794] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.701125] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.769712] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.777113] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.782521] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.791070] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.799701] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.806145] hub 1-0:1.0: USB hub found [ 3.809923] hub 1-0:1.0: 5 ports detected [ 3.814264] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.819665] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.827283] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.835664] hub 2-0:1.0: USB hub found [ 3.839437] hub 2-0:1.0: 4 ports detected [ 3.844560] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.857641] mmc1: Unknown controller version (3). You may experience problems. [ 3.896404] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.904538] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.916675] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.924332] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.931540] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.943736] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.973380] max77686-rtc max77620-rtc: setting system clock to 2017-12-19 10:00:47 UTC (1513677647) [ 4.177568] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.204259] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.216889] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.341951] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.402117] r8152 2-1:1.0 eth0: v1.09.9 [ 4.406165] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.418254] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 8.795651] r8152 2-1:1.0 eth0: carrier on [ 8.817065] IP-Config: Complete: [ 8.820288] device=eth0, hwaddr=00:04:4b:79:97:49, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 8.830451] host=192.168.99.2, domain=, nis-domain=(none) [ 8.836278] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 8.843693] AVDD_DSI_CSI_1V2: disabling [ 8.847541] VDD_PRE_REG_1V35: disabling [ 8.851383] VDD_CAM_HV: disabling [ 8.854836] VDD_TS_HV: disabling [ 8.858189] VDD_TS_1V8: disabling [ 8.861532] AVDD_SATA_HDMI_DP_1V05: disabling [ 8.865888] VDD_3V3_SD: disabling [ 8.869204] VDD_HDMI_5V0: disabling [ 8.872683] ALSA device list: [ 8.875648] No soundcards found. [ 8.879762] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 10:00:52 ] L4T-INITRD Build DATE: Tue Dec 19 10:00:52 UTC 2017 [ 10:00:52 ] Root device found: nfs [ 10:00:52 ] Ethernet interfaces: eth0 [ 10:00:52 ] IP Address: 192.168.99.2 [ 10:00:52 ] Rootfs mounted over nfs [ 10:00:52 ] Switching from initrd to actual rootfs [ 9.093495] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.111894] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.129999] systemd[1]: Set hostname to . [ 9.401036] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 9.417317] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 9.433239] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 9.453197] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 9.473108] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.489180] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 9.505161] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Created slice system-getty.slice. [ OK ] Listening on udev Control Socket. [ OK ] Reached target Encrypted Volumes. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Journal Socket. Mounting RPC Pipe File System... Mounting Debug File System... Mounting Huge Pages File System... Starting Create Static Device Nodes in /dev... Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... Starting Remount Root and Kernel File Systems... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. Starting Load Kernel Modules... [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. Starting Apply Kernel Variables... Mounting Configuration File System... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting udev Kernel Device Manager... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started udev Kernel Device Manager. [ 10.163353] systemd-journald[1531]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... [ OK ] Started D-Bus System Message Bus. Starting Login Service... Starting /etc/rc.local Compatibility... Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ 11.659803] random: crng init done [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ð