Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.57 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.98 sec Percent passed so far: 100.0 Final Score: 100.0 [0004.510] I> Welcome to MB1 recovery(prd-version : 10.02.161215-t186-M-00.00-f24525c4) [0004.518] I> rst_source : 0x0 [0004.521] I> rst_level : 0x0 [0004.524] I> Boot-device: eMMC [0004.548] I> sdmmc ddr50 mode [0004.552] I> Entering into 3p server.. [0004.555] I> Transport interface is USB [0004.848] I> transport_usbf_priv_open USB configuration success [0010.523] I> Populate eeprom info for module cvm [0042.926] I> bit @ 0xd480000 [0042.929] I> Downloading bct_bootrom at 0x000000004004e800 [0042.936] I> downloaded image bct_bootrom successfully [0042.942] I> Downloading bct_mb1 at 0x0000000040041000 [0042.952] I> MB1-BCT relocated to 0xd48bc00 from 0x40041000 [0042.958] I> Supported mb1-bct versions 9-12 [0042.962] I> Version of mb1 bct binary 12 [0042.966] W> MB1 BCT does not have controller prod config data [0042.971] I> Bootrom patch version : 31 (correctly patched) [0042.977] I> ATE fuse revision : 0x30080 [0042.981] I> chip revision : A02P [0042.984] I> disabled_core_mask: 0xffffff0c [0042.988] I> Enabled Cores: 0xf3 [0042.991] I> TPC disable fuse status: 0 [0042.995] I> Booting Parker Sku [0042.998] I> Ram repair fuse : 0x0 [0043.001] I> allocated(CO:30) base:0xf8000000 size:0x8000000 align: 0x8000000 [0043.008] I> allocated(CO:23) base:0xf7ff0000 size:0x10000 align: 0x10000 [0043.015] I> allocated(CO:31) base:0x0 size:0x0 align: 0x0 [0043.020] I> allocated(CO:1) base:0xf7e00000 size:0x100000 align: 0x100000 [0043.027] I> allocated(CO:2) base:0xf7d00000 size:0x100000 align: 0x100000 [0043.034] I> allocated(CO:3) base:0xf7c00000 size:0x100000 align: 0x100000 [0043.040] I> allocated(CO:4) base:0xf7b00000 size:0x100000 align: 0x100000 [0043.047] I> allocated(CO:5) base:0xf7a00000 size:0x100000 align: 0x100000 [0043.054] I> allocated(CO:8) base:0xf7900000 size:0x100000 align: 0x100000 [0043.061] I> allocated(CO:27) base:0x0 size:0x0 align: 0x0 [0043.066] I> allocated(CO:6) base:0xf7600000 size:0x200000 align: 0x200000 [0043.073] I> allocated(CO:7) base:0xf7000000 size:0x400000 align: 0x400000 [0043.080] I> allocated(CO:9) base:0xf7800000 size:0x100000 align: 0x100000 [0043.087] I> allocated(CO:10) base:0xf6800000 size:0x800000 align: 0x800000 [0043.093] I> allocated(CO:11) base:0x30000000 size:0x40000 align: 0x0 [0043.100] I> allocated(CO:12) base:0xf7500000 size:0x100000 align: 0x100000 [0043.107] I> allocated(CO:13) base:0x30040000 size:0x1000 align: 0x0 [0043.113] I> allocated(CO:14) base:0x30048000 size:0x1000 align: 0x0 [0043.119] I> allocated(CO:15) base:0x30049000 size:0x1000 align: 0x0 [0043.125] I> allocated(CO:16) base:0x3004a000 size:0x1000 align: 0x0 [0043.132] I> allocated(CO:17) base:0x3004b000 size:0x1000 align: 0x0 [0043.138] I> allocated(CO:19) base:0x3004d000 size:0x1000 align: 0x0 [0043.144] I> allocated(CO:18) base:0x3004c000 size:0x1000 align: 0x0 [0043.150] I> allocated(CO:20) base:0x3004e000 size:0x1000 align: 0x0 [0043.157] I> allocated(CO:21) base:0x3004f000 size:0x1000 align: 0x0 [0043.163] I> allocated(CO:22) base:0x0 size:0x0 align: 0x0 [0043.168] I> allocated(CO:32) base:0xf6000000 size:0x600000 align: 0x400000 [0043.175] I> allocated(CO:24) base:0x0 size:0x0 align: 0x0 [0043.181] I> allocated(CO:25) base:0x0 size:0x0 align: 0x0 [0043.186] I> allocated(CO:26) base:0x0 size:0x0 align: 0x0 [0043.191] I> allocated(CO:39) base:0x96000000 size:0x2000000 align: 0x2000000 [0043.198] I> allocated(CO:38) base:0x84000000 size:0x400000 align: 0x400000 [0043.205] I> allocated(CO:37) base:0xf7fc0000 size:0x20000 align: 0x20000 [0043.212] I> allocated(CO:40) base:0x84800000 size:0xb00000 align: 0x800000 [0043.219] I> allocated(CO:41) base:0xf7f00000 size:0x80000 align: 0x80000 [0043.225] I> allocated(CO:28) base:0x84400000 size:0x400000 align: 0x400000 [0043.233] I> Boot-device: eMMC [0043.236] I> sdmmc bdev is already initialized [0043.240] W> MB1 PMIC CFG is version 1.2 [0043.244] W> Rail ID 7 is not found on MB1 BCT [0043.249] W> MB1 PMIC CFG is version 1.2 [0043.255] W> MB1 PMIC CFG is version 1.2 [0043.262] W> MB1 PMIC CFG is version 1.2 [0043.266] I> sdram slot : 1 [0043.269] I> Initializing SDRAM [0043.275] I> mss encrypt status check successful [0043.280] I> downloaded image bct_mb1 successfully [0043.476] I> Downloading blob at 0x0000000085300000 [0043.859] I> downloaded image blob successfully [0043.873] I> exiting nv3p server [0043.876] I> disabled_core_mask: 0xffffff0c [0043.880] I> Enabled Cores: 0xf3 [0043.883] I> TPC disable fuse status: 0 [0043.887] I> Booting Parker Sku [0043.890] I> Setup temp. GSC#29 (base:0x30000000, size:0x00010000) [0043.896] I> Loading preboot [0043.901] I> Binary(1) of size 59024 is loaded @ 0x40000000 [0043.906] I> Restrict GSC#29 access to DPMU only [0043.911] I> Updated LSR_DVCOMP_PARAMS: 0xc0780f05c [0043.915] I> Updated LSR_DVCOMP_PARAMS: 0xc07a0f45c [0043.920] I> WP0 triggered [0043.923] I> Waypoint-0 ACK received :) [0043.926] I> WP0.5 triggered [0043.930] I> Initialized SCRs [0043.933] W> MB1 PMIC CFG is version 1.2 [0043.940] W> MB1 PMIC CFG is version 1.2 [0043.991] I> Waypoint-0.5 ACK received :) [0043.995] I> Setup temp. GSC#28 (base:0x84400000, size:0x00400000) [0044.001] I> Loading MTS-DMCE [0044.015] I> Binary(2) of size 266624 is loaded @ 0x84400000 [0044.020] I> disabled_core_mask: 0xffffff0c [0044.024] I> Loading MTS-PROPER [0044.027] I> Binary(3) of size 1809872 is loaded @ 0x0 [0044.032] I> Restrict GSC#28 access to DPMU only [0044.037] I> disabled_core_mask: 0xffffff0c [0044.041] I> WP1 triggered [0044.044] I> Loading MB2 [0044.047] I> Binary(8) of size 59696 is loaded @ 0x84000000 [0044.052] W> MB1 PMIC CFG is version 1.2 [0044.057] I> Configure DMCE carveout GSC#13 [0044.061] I> CPU reset vector: 0x96000000 [0044.065] I> MB2-params @ 0xf7f00000 [0044.069] I> Waypoint-1 ACK received :) [0044.073] I> Configure SC7 carveout GSC#23 [0044.077] I> MB1 recovery done [0044.082] I> Welcome to MB2(TBoot-BPMP) Recovery(version: 01.00.160913-t186-M-00.00-mobile-597f2c10) [0044.091] I> Default Heap @ [0xd486400 - 0xd488400] [0044.096] I> DMA Heap @ [0x84900000 - 0x85300000] [0044.101] I> bit @ 0xd480000 [0044.104] I> BR-BCT relocated to 0xf7f20000 [0044.108] I> Boot-device: eMMC [0044.112] I> pmic: reset reason (nverc) : 0x10 [0044.116] I> Reading GPT from 512 for device 00000003 [0044.122] I> Reading GPT from 8388096 for device 00000003 [0044.129] I> Found 6 partitions in 00000003 device [0044.134] I> Reading GPT from 512 for device 00010003 [0044.141] I> Found 18 partitions in 00010003 device [0044.149] I> Binary(16) of size 524480 is loaded @ 0xf7600000 [0044.156] I> Binary(17) of size 326672 is loaded @ 0xf77b03e0 [0044.283] I> BPMP-FW load address = 0xf7600000 [0044.287] I> BPMP-FW DTB load address = 0x501b03e0 [0044.292] I> Copy BTCM section [0044.296] I> Binary(13) of size 143872 is loaded @ 0x96000000 [0044.301] I> MB2-params @ 0xf7f00000 [0044.305] I> CPUBL-params @ 0xf7f00000 [0044.309] I> CPU-BL loaded at : 0x96000000 [0044.313] I> Loading TOS ... [0044.316] I> Binary(14) of size 54384 is loaded @ 0x8490f400 [0044.322] I> Copying Monitor (length: 0xd270) from 0x8490f600 to 0x40000000 [0044.329] I> Erasing Monitor @ 0x8490f600 [0044.333] I> Unhalting SCE [0044.337] I> Waypoint2-ACK: 0x5200b694 [0044.341] I> MB2(TBoot-BPMP) Recovery done NOTICE: BL31: v1.2(release):ff7a644 NOTICE: BL31: Built : 21:06:35, Mar 1 2017 NOTICE: Trusty image missing. ERROR: Error initializing runtime service trusty_fast [0044.703] I> Welcome to TBoot-CPU Recovery(version: 01.00.160913-t186-M-00.00-mobile-e9641362) [0044.711] I> gpio framework initialized [0044.715] I> tegrabl_gpio_driver_register: register 'tegra_gpio_main_driver' driver [0044.722] I> tegrabl_gpio_driver_register: register 'tegra_gpio_aon_driver' driver [0044.730] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0044.738] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0044.746] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0044.754] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0044.761] I> CPU: ARM Cortex A57 [0044.764] I> CPU: MIDR: 0x411fd073, MPIDR: 0x80000100 [0044.769] I> L2 ECC enabled : yes [0044.772] I> CPU-BL Params @ 0xf7f00000 [0044.776] I> 0) Base:0x00000000 Size:0x00000000 [0044.780] I> 1) Base:0xf7e00000 Size:0x00100000 [0044.784] I> 2) Base:0xf7d00000 Size:0x00100000 [0044.789] I> 3) Base:0xf7c00000 Size:0x00100000 [0044.793] I> 4) Base:0xf7b00000 Size:0x00100000 [0044.798] I> 5) Base:0xf7a00000 Size:0x00100000 [0044.802] I> 6) Base:0xf7600000 Size:0x00200000 [0044.807] I> 7) Base:0xf7000000 Size:0x00400000 [0044.811] I> 8) Base:0xf7900000 Size:0x00100000 [0044.815] I> 9) Base:0xf7800000 Size:0x00100000 [0044.820] I> 10) Base:0xf6800000 Size:0x00800000 [0044.824] I> 11) Base:0x30000000 Size:0x00040000 [0044.829] I> 12) Base:0xf7500000 Size:0x00100000 [0044.833] I> 13) Base:0x30040000 Size:0x00001000 [0044.838] I> 14) Base:0x30048000 Size:0x00001000 [0044.842] I> 15) Base:0x30049000 Size:0x00001000 [0044.846] I> 16) Base:0x3004a000 Size:0x00001000 [0044.851] I> 17) Base:0x3004b000 Size:0x00001000 [0044.855] I> 18) Base:0x3004c000 Size:0x00001000 [0044.860] I> 19) Base:0x3004d000 Size:0x00001000 [0044.864] I> 20) Base:0x3004e000 Size:0x00001000 [0044.869] I> 21) Base:0x3004f000 Size:0x00001000 [0044.873] I> 22) Base:0x00000000 Size:0x00000000 [0044.878] I> 23) Base:0xf7ff0000 Size:0x00010000 [0044.882] I> 24) Base:0x00000000 Size:0x00000000 [0044.886] I> 25) Base:0x00000000 Size:0x00000000 [0044.891] I> 26) Base:0x00000000 Size:0x00000000 [0044.895] I> 27) Base:0x00000000 Size:0x00000000 [0044.900] I> 28) Base:0x84400000 Size:0x00400000 [0044.904] I> 29) Base:0x30000000 Size:0x00010000 [0044.909] I> 30) Base:0xf8000000 Size:0x08000000 [0044.913] I> 31) Base:0x00000000 Size:0x00000000 [0044.917] I> 32) Base:0xf6000000 Size:0x00600000 [0044.922] I> 33) Base:0x80000000 Size:0x76000000 [0044.926] I> 34) Base:0x100000000 Size:0x180000000 [0044.931] I> 35) Base:0x00000000 Size:0x00000000 [0044.935] I> 36) Base:0x00000000 Size:0x00000000 [0044.940] I> 37) Base:0xf7fc0000 Size:0x00020000 [0044.944] I> 38) Base:0x84000000 Size:0x00400000 [0044.949] I> 39) Base:0x96000000 Size:0x02000000 [0044.953] I> 40) Base:0x84800000 Size:0x00b00000 [0044.957] I> 41) Base:0xf7f00000 Size:0x00080000 [0044.962] I> 42) Base:0x00000000 Size:0x00000000 [0044.966] I> 43) Base:0x00000000 Size:0x00000000 [0044.971] I> Boot-device: eMMC [0044.996] I> sdmmc ddr50 mode [0044.999] I> sdmmc bdev is already initialized [0045.003] I> Reading GPT from 512 for device 00000003 [0045.009] I> Reading GPT from 8388096 for device 00000003 [0045.016] I> Found 6 partitions in 00000003 device [0045.020] I> Reading GPT from 512 for device 00010003 [0045.026] I> Found 18 partitions in 00010003 device [0045.031] I> Recovery boot_type: 0 [0045.034] I> Entering 3p server [0045.037] I> Entering into 3p server.. [0045.040] I> Transport interface is USB [0045.332] I> transport_usbf_priv_open USB configuration success [0048.913] I> Populate storage info [0048.929] I> Erasing device 0: 3 [0048.932] I> Erasing device 16384 blocks from block 0 [0048.953] I> Erase successful. [0048.957] I> Writing device 0: 3 [0048.960] I> Total write size is 16896 bytes [0049.003] I> Reading GPT from 512 for device 00000003 [0049.008] I> Reading GPT from 8388096 for device 00000003 [0049.015] I> Found 6 partitions in 00000003 device [0049.020] I> Write successful. [0049.023] I> Erasing device 1: 3 [0049.027] I> Erasing device 61071360 blocks from block 0 [0049.546] I> Erase successful. [0049.550] I> Writing device 1: 3 [0049.553] I> Total write size is 512 bytes [0049.559] I> Write successful. [0049.562] I> Writing device 1: 3 [0049.565] I> Total write size is 2688 bytes [0049.572] I> Reading GPT from 512 for device 00010003 [0049.578] I> Found 17 partitions in 00010003 device [0049.582] I> Write successful. [0049.586] I> Writing device 1: 3 [0049.589] I> Total write size is 16896 bytes [0049.596] I> Reading GPT from 512 for device 00010003 [0049.601] I> Found 17 partitions in 00010003 device [0049.606] I> Write successful. [0049.610] I> Writing mb1 partition [0049.613] I> Total write size is 88368 bytes [0049.641] I> Write successful. [0049.645] I> Writing spe-fw partition [0049.648] I> Total write size is 57184 bytes [0049.677] I> Write successful. [0049.681] I> Writing mb2 partition [0049.684] I> Total write size is 60720 bytes [0049.718] I> Write successful. [0049.722] I> Writing mts-preboot partition [0049.726] I> Total write size is 59824 bytes [0049.765] I> Write successful. [0049.769] I> Writing device 1: 3 [0049.772] I> Total write size is 512 bytes [0049.777] I> Write successful. [0049.781] I> Writing APP partition [0049.785] I> Total write size is 27976980 bytes [0050.986] I> Write successful. [0050.990] I> Writing mts-bootpack partition [0050.994] I> Total write size is 2077344 bytes [0051.084] I> Write successful. [0051.087] I> Writing cpu-bootloader partition [0051.092] I> Total write size is 196176 bytes [0051.108] I> Write successful. [0051.112] I> Writing bootloader-dtb partition [0051.116] I> Total write size is 248528 bytes [0051.139] I> Write successful. [0051.143] I> Writing secure-os partition [0051.147] I> Total write size is 54784 bytes [0051.155] I> Write successful. [0051.158] I> Writing eks partition [0051.162] I> Total write size is 1488 bytes [0051.168] I> Write successful. [0051.172] I> Writing bpmp-fw partition [0051.175] I> Total write size is 524880 bytes [0051.203] I> Write successful. [0051.207] I> Writing bpmp-fw-dtb partition [0051.211] I> Total write size is 327072 bytes [0051.231] I> Write successful. [0051.235] I> Writing sce-fw partition [0051.238] I> Total write size is 65488 bytes [0051.248] I> Write successful. [0051.252] I> Writing sc7 partition [0051.255] I> Total write size is 20848 bytes [0051.262] I> Write successful. [0051.266] I> Writing kernel partition [0051.270] I> Total write size is 6735872 bytes [0051.582] I> Write successful. [0051.586] I> Writing kernel-dtb partition [0051.590] I> Total write size is 248128 bytes [0051.606] I> Write successful. [0051.616] I> Writing BCT partition [0051.620] I> Total write size is 3584 bytes [0051.660] I> Write successful. [0051.678] I> Writing MB1_BCT partition [0051.682] I> Total write size is 49968 bytes [0051.722] I> Write successful. [0051.732] I> Rebooting : reset-coldboot [0000.191] I> Welcome to MB2(TBoot-BPMP)(version: 01.00.160913-t186-M-00.00-mobile-f4c42291) [0000.199] I> Default Heap @ [0xd486400 - 0xd488400] [0000.204] I> DMA Heap @ [0x84900000 - 0x85300000] [0000.209] I> bit @ 0xd480000 [0000.211] I> BR-BCT relocated to 0xf7f20000 [0000.216] I> Boot-device: eMMC [0000.220] I> pmic: reset reason (nverc) : 0x0 [0000.224] I> Reading GPT from 512 for device 00000003 [0000.230] I> Reading GPT from 8388096 for device 00000003 [0000.237] I> Found 6 partitions in 00000003 device [0000.242] I> Reading GPT from 512 for device 00010003 [0000.248] I> Found 17 partitions in 00010003 device [0000.253] W> No valid slot number is found in scratch register [0000.259] W> Return default slot: _a [0000.262] I> A/B: bin_type (16) slot 0 [0000.266] I> Select partition: bpmp-fw [0000.270] I> Loading partition bpmp-fw at 0xf7600000 [0000.274] I> Reading two headers - addr:0xf7600000 blocks:1 [0000.280] I> Addr: 0xf7600000, start-block: 58739717, num_blocks: 1 [0000.295] I> Binary(16) of size 524480 is loaded @ 0xf7600000 [0000.300] W> No valid slot number is found in scratch register [0000.306] W> Return default slot: _a [0000.309] I> A/B: bin_type (17) slot 0 [0000.313] I> Select partition: bpmp-fw-dtb [0000.317] I> Loading partition bpmp-fw-dtb at 0xf77f0000 [0000.322] I> Reading two headers - addr:0xf77f0000 blocks:1 [0000.328] I> Addr: 0xf77f0000, start-block: 58740925, num_blocks: 1 [0000.340] I> Binary(17) of size 326672 is loaded @ 0xf77b0200 [0000.466] I> BPMP-FW load address = 0xf7600000 [0000.471] I> BPMP-FW DTB load address = 0x501b0200 [0000.475] I> Loading SCE-FW ... [0000.478] W> No valid slot number is found in scratch register [0000.484] W> Return default slot: _a [0000.488] I> A/B: bin_type (12) slot 0 [0000.491] I> Select partition: sce-fw [0000.495] I> Loading partition sce-fw at 0xf7800000 [0000.499] I> Reading two headers - addr:0xf7800000 blocks:1 [0000.505] I> Addr: 0xf7800000, start-block: 58741925, num_blocks: 1 [0000.513] I> Binary(12) of size 65088 is loaded @ 0xf7800000 [0000.519] I> Init SCE [0000.521] I> Copy BTCM section [0000.524] W> No valid slot number is found in scratch register [0000.530] W> Return default slot: _a [0000.533] I> A/B: bin_type (13) slot 0 [0000.537] I> Select partition: cpu-bootloader [0000.541] I> Loading partition cpu-bootloader at 0x96000000 [0000.546] I> Reading two headers - addr:0x96000000 blocks:1 [0000.552] I> Addr: 0x96000000, start-block: 58732545, num_blocks: 1 [0000.562] I> Binary(13) of size 195776 is loaded @ 0x96000000 [0000.568] W> No valid slot number is found in scratch register [0000.573] W> Return default slot: _a [0000.577] I> A/B: bin_type (20) slot 0 [0000.581] I> Select partition: bootloader-dtb [0000.585] I> Loading partition bootloader-dtb at 0x85300000 [0000.590] I> Reading two headers - addr:0x85300000 blocks:1 [0000.596] I> Addr: 0x85300000, start-block: 58733057, num_blocks: 1 [0000.607] I> Binary(20) of size 248128 is loaded @ 0x85300000 [0000.612] I> MB2-params @ 0xf7f00000 [0000.616] I> CPUBL-params @ 0xf7f00000 [0000.619] I> CPU-BL loaded at : 0x96000000 [0000.623] I> Loading TOS ... [0000.626] W> No valid slot number is found in scratch register [0000.632] W> Return default slot: _a [0000.635] I> A/B: bin_type (14) slot 0 [0000.639] I> Select partition: secure-os [0000.643] I> Loading partition secure-os at 0x8490f400 [0000.648] I> Reading two headers - addr:0x8490f400 blocks:1 [0000.653] I> Addr: 0x8490f400, start-block: 58733569, num_blocks: 1 [0000.661] I> Binary(14) of size 54384 is loaded @ 0x8490f400 [0000.667] I> Copying Monitor (length: 0xd270) from 0x8490f600 to 0x40000000 [0000.674] I> Erasing Monitor @ 0x8490f600 [0000.678] I> Unhalting SCE [0000.682] I> Waypoint2-ACK: 0x5200b8d0 [0000.686] I> MB2(TBoot-BPMP) done NOTICE: BL31: v1.2(release):ff7a644 NOTICE: BL31: Built : 21:06:35, Mar 1 2017 NOTICE: Trusty image missing. ERROR: Error initializing runtime service trusty_fast [0001.048] I> Welcome to Cboot [0001.051] I> Cboot Version: 00.00.2014.50-t186-fabbc56c [0001.056] I> CPU-BL Params @ 0xf7f00000 [0001.059] I> 0) Base:0x00000000 Size:0x00000000 [0001.064] I> 1) Base:0xf7e00000 Size:0x00100000 [0001.068] I> 2) Base:0xf7d00000 Size:0x00100000 [0001.073] I> 3) Base:0xf7c00000 Size:0x00100000 [0001.077] I> 4) Base:0xf7b00000 Size:0x00100000 [0001.082] I> 5) Base:0xf7a00000 Size:0x00100000 [0001.086] I> 6) Base:0xf7600000 Size:0x00200000 [0001.090] I> 7) Base:0xf7000000 Size:0x00400000 [0001.095] I> 8) Base:0xf7900000 Size:0x00100000 [0001.099] I> 9) Base:0xf7800000 Size:0x00100000 [0001.104] I> 10) Base:0xf6800000 Size:0x00800000 [0001.108] I> 11) Base:0x30000000 Size:0x00040000 [0001.113] I> 12) Base:0xf7500000 Size:0x00100000 [0001.117] I> 13) Base:0x30040000 Size:0x00001000 [0001.121] I> 14) Base:0x30048000 Size:0x00001000 [0001.126] I> 15) Base:0x30049000 Size:0x00001000 [0001.130] I> 16) Base:0x3004a000 Size:0x00001000 [0001.135] I> 17) Base:0x3004b000 Size:0x00001000 [0001.139] I> 18) Base:0x3004c000 Size:0x00001000 [0001.144] I> 19) Base:0x3004d000 Size:0x00001000 [0001.148] I> 20) Base:0x3004e000 Size:0x00001000 [0001.152] I> 21) Base:0x3004f000 Size:0x00001000 [0001.157] I> 22) Base:0x00000000 Size:0x00000000 [0001.161] I> 23) Base:0xf7ff0000 Size:0x00010000 [0001.166] I> 24) Base:0x00000000 Size:0x00000000 [0001.170] I> 25) Base:0x00000000 Size:0x00000000 [0001.175] I> 26) Base:0x00000000 Size:0x00000000 [0001.179] I> 27) Base:0x00000000 Size:0x00000000 [0001.183] I> 28) Base:0x84400000 Size:0x00400000 [0001.188] I> 29) Base:0x30000000 Size:0x00010000 [0001.192] I> 30) Base:0xf8000000 Size:0x08000000 [0001.197] I> 31) Base:0x00000000 Size:0x00000000 [0001.201] I> 32) Base:0xf6000000 Size:0x00600000 [0001.206] I> 33) Base:0x80000000 Size:0x76000000 [0001.210] I> 34) Base:0x100000000 Size:0x180000000 [0001.215] I> 35) Base:0x00000000 Size:0x00000000 [0001.219] I> 36) Base:0x00000000 Size:0x00000000 [0001.223] I> 37) Base:0xf7fc0000 Size:0x00020000 [0001.228] I> 38) Base:0x84000000 Size:0x00400000 [0001.232] I> 39) Base:0x96000000 Size:0x02000000 [0001.237] I> 40) Base:0x84800000 Size:0x00b00000 [0001.241] I> 41) Base:0xf7f00000 Size:0x00080000 [0001.246] I> 42) Base:0x00000000 Size:0x00000000 [0001.250] I> 43) Base:0x00000000 Size:0x00000000 [0001.254] platform_init_interrupts-121, 1* [0001.259] Interrupts Init done [0001.262] calling constructors [0001.265] initializing heap [0001.268] initializing threads [0001.271] initializing timers [0001.274] creating bootstrap completion thread [0001.279] top of bootstrap2() [0001.282] CPU: ARM Cortex A57 [0001.285] CPU: MIDR: 0x411FD073, MPIDR: 0x80000100 [0001.290] initializing platform [0001.293] I> Boot-device: eMMC [0001.297] I> odm data is 1090000 [0001.300] I> Reading GPT from 512 for device 00000003 [0001.305] I> Reading GPT from 8388096 for device 00000003 [0001.312] I> Found 6 partitions in 00000003 device [0001.316] I> Reading GPT from 512 for device 00010003 [0001.322] I> Found 17 partitions in 00010003 device [0001.327] W> No valid slot number is found in scratch register [0001.333] W> Return default slot: _a [0001.336] I> A/B: bin_type (1) slot 0 [0001.340] I> Select partition: kernel-dtb [0001.343] I> Loading partition kernel-dtb at 0x92000000 [0001.352] I> Kernel_dtb @0x92000000 [0001.355] I> Bl_dtb @0x85300000 [0001.358] I> gpio framework initialized [0001.362] I> tegrabl_gpio_driver_register: register 'tegra_gpio_main_driver' driver [0001.370] I> tegrabl_gpio_driver_register: register 'tegra_gpio_aon_driver' driver [0001.377] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0001.385] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.393] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0001.401] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.409] E> tegrabl_blob_init: BMP partition does not have valid Blob [0001.415] E> tegrabl_load_bmp_blob: BMP blob initialization failed [0001.421] W> Loading bmp blob to memory failed [0001.429] I> Find /i2c@c250000's alias i2c7 [0001.433] I> Reading eeprom i2c=7 address=0x50 [0001.463] I> Device at /i2c@c250000:0x50 [0001.467] I> Reading eeprom i2c=7 address=0x57 [0001.496] I> Device at /i2c@c250000:0x57 [0001.500] I> Find /i2c@c240000's alias i2c1 [0001.504] I> Reading eeprom i2c=1 address=0x51 [0001.510] I> Eeprom read failed 0x1a800027 [0001.514] I> Find /i2c@3160000's alias i2c0 [0001.518] I> Reading eeprom i2c=0 address=0x50 [0001.524] I> Eeprom read failed 0x1a800027 [0001.529] I> Find /i2c@3180000's alias i2c2 [0001.533] I> Reading eeprom i2c=2 address=0x54 [0001.537] I> Enabling gpio chip_id = 2, gpio pin = 9 [0001.567] I> Disabling gpio chip_id = 2, gpio pin = 9 [0001.573] I> Device at /i2c@3180000:0x54 [0001.576] I> create_pm_ids: id: 3310-1000-B00-B, len: 15 [0001.582] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.592] I> create_pm_ids: id: 2597-0000-500-C, len: 15 [0001.598] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.608] I> create_pm_ids: id: 3326-1000-000-M, len: 15 [0001.614] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0001.625] initializing target [0001.628] calling apps_init() [0001.631] starting app android_boot_app [0001.635] I> Gpio keyboard init success [0001.638] I> Kernel type = Normal [0001.641] I> Loading kernel/boot.img ... [0001.645] W> No valid slot number is found in scratch register [0001.651] W> Return default slot: _a [0001.654] I> A/B: bin_type (0) slot 0 [0001.658] I> Select partition: kernel [0001.661] I> Loading partition kernel at 0xa8000000 [0001.743] W> No valid slot number is found in scratch register [0001.748] W> Return default slot: _a [0001.752] I> A/B: bin_type (1) slot 0 [0001.755] I> Select partition: kernel-dtb [0001.759] I> Loading partition kernel-dtb at 0x92000000 [0001.768] I> Kernel DTB @ 0x92000000 [0001.771] I> Verified boot state = Orange [0001.775] E> tegrabl_display_clear: display is not initialized [0001.781] I> Checking boot.img header magic ... [0001.785] I> [OK] [0001.787] I> Valid boot.img @ 0xa8000000 [0001.790] I> decompressor handler not found [0001.794] I> Copying kernel image (465664 bytes) from 0xa8000800 to 0x80080000 ... [0001.802] I> Done [0001.803] I> Move ramdisk (len: 6266481) from 0xa8072800 to 0x98000000 [0001.813] I> Updated bpmp info to DTB [0001.819] I> Ramdisk: Base: 0x98000000; Size: 0x5f9e71 [0001.824] I> Updated initrd info to DTB [0001.827] I> disabled_core_mask: 0xffffff0c [0001.831] I> Kernel type = Normal [0001.834] I> add_serialno: Serial Num = 0330117020898 [0001.839] W> No valid slot number is found in scratch register [0001.845] W> Return default slot: _a [0001.848] I> Linux Cmdline: root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3576/nfsroot fbcon=map:0 net.ifnames=0 console=tty0 OS=l4t console=ttyS0,115200n8 memtype=0 video=tegrafb no_console_suspend=1 earlycon=uart8250,mmio32,0x03100000 nvdumper_reserved=0xf7fc0000 gpt androidboot.secureos=none tegraid=18.1.2.0.0 tegra_keep_boot_clocks maxcpus=6 android.kerneltype=normal androidboot.serialno=0330117020898 androidboot.security=non-secure sdhci_tegra.en_boot_part_access=1 [0001.897] I> Updated bootarg info to DTB [0001.902] I> eeprom_get_mac_addr: MAC (type: 0): 00:04:4b:81:c6:4e [0001.908] I> eeprom_get_mac_addr: MAC (type: 1): 00:04:4b:81:c6:4f [0001.914] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:81:c6:50 [0001.920] E> "ids" doesn't exist, creating [0001.924] E> "connection" doesn't exist, creating [0001.929] E> "configs" doesn't exist, creating [0001.933] I> create_pm_ids: id: 3310-1000-B00-B, len: 15 [0001.938] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.949] I> create_pm_ids: id: 2597-0000-500-C, len: 15 [0001.954] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.965] I> create_pm_ids: id: 3326-1000-000-M, len: 15 [0001.970] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0001.981] I> Adding plugin-manager/ids/3310-1000-B00=/i2c@c250000:module@0x50 [0001.988] E> "i2c@c250000" doesn't exist, creating [0001.993] E> "module@0x50" doesn't exist, creating [0001.998] I> Adding plugin-manager/ids/2597-0000-500=/i2c@c250000:module@0x57 [0002.005] E> "module@0x57" doesn't exist, creating [0002.010] I> Adding plugin-manager/ids/3326-1000-000=/i2c@3180000:module@0x54 [0002.017] E> "i2c@3180000" doesn't exist, creating [0002.022] E> "module@0x54" doesn't exist, creating [0002.028] I> Adding plugin-manager/ids/3310-1000-B00-B [0002.035] I> Adding plugin-manager/configs/3310-mem-type 00 [0002.041] I> Adding plugin-manager/configs/3310-power-config 00 [0002.047] I> Adding plugin-manager/configs/3310-misc-config 00 [0002.052] I> Adding plugin-manager/configs/3310-modem-config 00 [0002.058] I> Adding plugin-manager/configs/3310-touch-config 00 [0002.064] I> Adding plugin-manager/configs/3310-display-config 00 [0002.070] E> "chip-id" doesn't exist, creating [0002.074] I> Adding plugin-manager/chip-id/A02P [0002.081] I> Updated memory info to DTB [0002.086] E> "reset" doesn't exist, creating [0002.090] E> "pmc-reset-reason" doesn't exist, creating [0002.096] E> "pmic-reset-reason" doesn't exist, creating [0002.101] I> disabled_core_mask: 0xffffff0c [0002.112] I> tegrabl_load_kernel_and_dtb: Done U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:46:37 -0700) TEGRA186 Model: NVIDIA P2771-0000-500 DRAM: 7.8 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 [0000.183] I> Welcome to MB2(TBoot-BPMP)(version: 01.00.160913-t186-M-00.00-mobile-f4c42291) [0000.191] I> Default Heap @ [0xd486400 - 0xd488400] [0000.196] I> DMA Heap @ [0x84900000 - 0x85300000] [0000.201] I> bit @ 0xd480000 [0000.204] I> BR-BCT relocated to 0xf7f20000 [0000.208] I> Boot-device: eMMC [0000.212] I> pmic: reset reason (nverc) : 0x10 [0000.216] I> Reading GPT from 512 for device 00000003 [0000.222] I> Reading GPT from 8388096 for device 00000003 [0000.229] I> Found 6 partitions in 00000003 device [0000.234] I> Reading GPT from 512 for device 00010003 [0000.240] I> Found 17 partitions in 00010003 device [0000.246] W> No valid slot number is found in scratch register [0000.251] W> Return default slot: _a [0000.255] I> A/B: bin_type (16) slot 0 [0000.258] I> Select partition: bpmp-fw [0000.262] I> Loading partition bpmp-fw at 0xf7600000 [0000.267] I> Reading two headers - addr:0xf7600000 blocks:1 [0000.272] I> Addr: 0xf7600000, start-block: 58739717, num_blocks: 1 [0000.287] I> Binary(16) of size 524480 is loaded @ 0xf7600000 [0000.293] W> No valid slot number is found in scratch register [0000.298] W> Return default slot: _a [0000.302] I> A/B: bin_type (17) slot 0 [0000.305] I> Select partition: bpmp-fw-dtb [0000.309] I> Loading partition bpmp-fw-dtb at 0xf77f0000 [0000.314] I> Reading two headers - addr:0xf77f0000 blocks:1 [0000.320] I> Addr: 0xf77f0000, start-block: 58740925, num_blocks: 1 [0000.332] I> Binary(17) of size 326672 is loaded @ 0xf77b0200 [0000.459] I> BPMP-FW load address = 0xf7600000 [0000.464] I> BPMP-FW DTB load address = 0x501b0200 [0000.469] I> Loading SCE-FW ... [0000.472] W> No valid slot number is found in scratch register [0000.477] W> Return default slot: _a [0000.481] I> A/B: bin_type (12) slot 0 [0000.484] I> Select partition: sce-fw [0000.488] I> Loading partition sce-fw at 0xf7800000 [0000.492] I> Reading two headers - addr:0xf7800000 blocks:1 [0000.498] I> Addr: 0xf7800000, start-block: 58741925, num_blocks: 1 [0000.506] I> Binary(12) of size 65088 is loaded @ 0xf7800000 [0000.512] I> Init SCE [0000.514] I> Copy BTCM section [0000.517] W> No valid slot number is found in scratch register [0000.523] W> Return default slot: _a [0000.526] I> A/B: bin_type (13) slot 0 [0000.530] I> Select partition: cpu-bootloader [0000.534] I> Loading partition cpu-bootloader at 0x96000000 [0000.540] I> Reading two headers - addr:0x96000000 blocks:1 [0000.545] I> Addr: 0x96000000, start-block: 58732545, num_blocks: 1 [0000.555] I> Binary(13) of size 195776 is loaded @ 0x96000000 [0000.561] W> No valid slot number is found in scratch register [0000.567] W> Return default slot: _a [0000.570] I> A/B: bin_type (20) slot 0 [0000.574] I> Select partition: bootloader-dtb [0000.578] I> Loading partition bootloader-dtb at 0x85300000 [0000.583] I> Reading two headers - addr:0x85300000 blocks:1 [0000.589] I> Addr: 0x85300000, start-block: 58733057, num_blocks: 1 [0000.600] I> Binary(20) of size 248128 is loaded @ 0x85300000 [0000.605] I> MB2-params @ 0xf7f00000 [0000.609] I> CPUBL-params @ 0xf7f00000 [0000.612] I> CPU-BL loaded at : 0x96000000 [0000.616] I> Loading TOS ... [0000.619] W> No valid slot number is found in scratch register [0000.625] W> Return default slot: _a [0000.628] I> A/B: bin_type (14) slot 0 [0000.632] I> Select partition: secure-os [0000.636] I> Loading partition secure-os at 0x8490f400 [0000.641] I> Reading two headers - addr:0x8490f400 blocks:1 [0000.646] I> Addr: 0x8490f400, start-block: 58733569, num_blocks: 1 [0000.654] I> Binary(14) of size 54384 is loaded @ 0x8490f400 [0000.660] I> Copying Monitor (length: 0xd270) from 0x8490f600 to 0x40000000 [0000.667] I> Erasing Monitor @ 0x8490f600 [0000.672] I> Unhalting SCE [0000.675] I> Waypoint2-ACK: 0x5200b8d0 [0000.679] I> MB2(TBoot-BPMP) done NOTICE: BL31: v1.2(release):ff7a644 NOTICE: BL31: Built : 21:06:35, Mar 1 2017 NOTICE: Trusty image missing. ERROR: Error initializing runtime service trusty_fast [0001.041] I> Welcome to Cboot [0001.044] I> Cboot Version: 00.00.2014.50-t186-fabbc56c [0001.049] I> CPU-BL Params @ 0xf7f00000 [0001.053] I> 0) Base:0x00000000 Size:0x00000000 [0001.057] I> 1) Base:0xf7e00000 Size:0x00100000 [0001.061] I> 2) Base:0xf7d00000 Size:0x00100000 [0001.066] I> 3) Base:0xf7c00000 Size:0x00100000 [0001.070] I> 4) Base:0xf7b00000 Size:0x00100000 [0001.075] I> 5) Base:0xf7a00000 Size:0x00100000 [0001.079] I> 6) Base:0xf7600000 Size:0x00200000 [0001.084] I> 7) Base:0xf7000000 Size:0x00400000 [0001.088] I> 8) Base:0xf7900000 Size:0x00100000 [0001.092] I> 9) Base:0xf7800000 Size:0x00100000 [0001.097] I> 10) Base:0xf6800000 Size:0x00800000 [0001.101] I> 11) Base:0x30000000 Size:0x00040000 [0001.106] I> 12) Base:0xf7500000 Size:0x00100000 [0001.110] I> 13) Base:0x30040000 Size:0x00001000 [0001.115] I> 14) Base:0x30048000 Size:0x00001000 [0001.119] I> 15) Base:0x30049000 Size:0x00001000 [0001.123] I> 16) Base:0x3004a000 Size:0x00001000 [0001.128] I> 17) Base:0x3004b000 Size:0x00001000 [0001.132] I> 18) Base:0x3004c000 Size:0x00001000 [0001.137] I> 19) Base:0x3004d000 Size:0x00001000 [0001.141] I> 20) Base:0x3004e000 Size:0x00001000 [0001.146] I> 21) Base:0x3004f000 Size:0x00001000 [0001.150] I> 22) Base:0x00000000 Size:0x00000000 [0001.154] I> 23) Base:0xf7ff0000 Size:0x00010000 [0001.159] I> 24) Base:0x00000000 Size:0x00000000 [0001.163] I> 25) Base:0x00000000 Size:0x00000000 [0001.168] I> 26) Base:0x00000000 Size:0x00000000 [0001.172] I> 27) Base:0x00000000 Size:0x00000000 [0001.177] I> 28) Base:0x84400000 Size:0x00400000 [0001.181] I> 29) Base:0x30000000 Size:0x00010000 [0001.185] I> 30) Base:0xf8000000 Size:0x08000000 [0001.190] I> 31) Base:0x00000000 Size:0x00000000 [0001.194] I> 32) Base:0xf6000000 Size:0x00600000 [0001.199] I> 33) Base:0x80000000 Size:0x76000000 [0001.203] I> 34) Base:0x100000000 Size:0x180000000 [0001.208] I> 35) Base:0x00000000 Size:0x00000000 [0001.212] I> 36) Base:0x00000000 Size:0x00000000 [0001.217] I> 37) Base:0xf7fc0000 Size:0x00020000 [0001.221] I> 38) Base:0x84000000 Size:0x00400000 [0001.225] I> 39) Base:0x96000000 Size:0x02000000 [0001.230] I> 40) Base:0x84800000 Size:0x00b00000 [0001.234] I> 41) Base:0xf7f00000 Size:0x00080000 [0001.239] I> 42) Base:0x00000000 Size:0x00000000 [0001.243] I> 43) Base:0x00000000 Size:0x00000000 [0001.248] platform_init_interrupts-121, 1* [0001.252] Interrupts Init done [0001.255] calling constructors [0001.258] initializing heap [0001.261] initializing threads [0001.264] initializing timers [0001.267] creating bootstrap completion thread [0001.272] top of bootstrap2() [0001.275] CPU: ARM Cortex A57 [0001.278] CPU: MIDR: 0x411FD073, MPIDR: 0x80000100 [0001.283] initializing platform [0001.286] I> Boot-device: eMMC [0001.290] I> odm data is 1090000 [0001.293] I> Reading GPT from 512 for device 00000003 [0001.299] I> Reading GPT from 8388096 for device 00000003 [0001.305] I> Found 6 partitions in 00000003 device [0001.310] I> Reading GPT from 512 for device 00010003 [0001.316] I> Found 17 partitions in 00010003 device [0001.320] W> No valid slot number is found in scratch register [0001.326] W> Return default slot: _a [0001.329] I> A/B: bin_type (1) slot 0 [0001.333] I> Select partition: kernel-dtb [0001.337] I> Loading partition kernel-dtb at 0x92000000 [0001.345] I> Kernel_dtb @0x92000000 [0001.349] I> Bl_dtb @0x85300000 [0001.352] I> gpio framework initialized [0001.355] I> tegrabl_gpio_driver_register: register 'tegra_gpio_main_driver' driver [0001.363] I> tegrabl_gpio_driver_register: register 'tegra_gpio_aon_driver' driver [0001.370] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0001.379] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.386] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0001.394] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.402] E> tegrabl_blob_init: BMP partition does not have valid Blob [0001.408] E> tegrabl_load_bmp_blob: BMP blob initialization failed [0001.414] W> Loading bmp blob to memory failed [0001.423] I> Find /i2c@c250000's alias i2c7 [0001.427] I> Reading eeprom i2c=7 address=0x50 [0001.456] I> Device at /i2c@c250000:0x50 [0001.460] I> Reading eeprom i2c=7 address=0x57 [0001.489] I> Device at /i2c@c250000:0x57 [0001.493] I> Find /i2c@c240000's alias i2c1 [0001.497] I> Reading eeprom i2c=1 address=0x51 [0001.503] I> Eeprom read failed 0x1a800027 [0001.507] I> Find /i2c@3160000's alias i2c0 [0001.511] I> Reading eeprom i2c=0 address=0x50 [0001.517] I> Eeprom read failed 0x1a800027 [0001.522] I> Find /i2c@3180000's alias i2c2 [0001.526] I> Reading eeprom i2c=2 address=0x54 [0001.530] I> Enabling gpio chip_id = 2, gpio pin = 9 [0001.561] I> Disabling gpio chip_id = 2, gpio pin = 9 [0001.566] I> Device at /i2c@3180000:0x54 [0001.570] I> create_pm_ids: id: 3310-1000-B00-B, len: 15 [0001.575] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.586] I> create_pm_ids: id: 2597-0000-500-C, len: 15 [0001.591] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.602] I> create_pm_ids: id: 3326-1000-000-M, len: 15 [0001.607] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0001.618] initializing target [0001.621] calling apps_init() [0001.624] starting app android_boot_app [0001.628] I> Gpio keyboard init success [0001.632] I> Kernel type = Normal [0001.635] I> Loading kernel/boot.img ... [0001.638] W> No valid slot number is found in scratch register [0001.644] W> Return default slot: _a [0001.647] I> A/B: bin_type (0) slot 0 [0001.651] I> Select partition: kernel [0001.654] I> Loading partition kernel at 0xa8000000 [0001.736] W> No valid slot number is found in scratch register [0001.741] W> Return default slot: _a [0001.745] I> A/B: bin_type (1) slot 0 [0001.748] I> Select partition: kernel-dtb [0001.752] I> Loading partition kernel-dtb at 0x92000000 [0001.761] I> Kernel DTB @ 0x92000000 [0001.764] I> Verified boot state = Orange [0001.768] E> tegrabl_display_clear: display is not initialized [0001.774] I> Checking boot.img header magic ... [0001.778] I> [OK] [0001.780] I> Valid boot.img @ 0xa8000000 [0001.783] I> decompressor handler not found [0001.787] I> Copying kernel image (465664 bytes) from 0xa8000800 to 0x80080000 ... [0001.795] I> Done [0001.797] I> Move ramdisk (len: 6266481) from 0xa8072800 to 0x98000000 [0001.806] I> Updated bpmp info to DTB [0001.812] I> Ramdisk: Base: 0x98000000; Size: 0x5f9e71 [0001.817] I> Updated initrd info to DTB [0001.820] I> disabled_core_mask: 0xffffff0c [0001.824] I> Kernel type = Normal [0001.828] I> add_serialno: Serial Num = 0330117020898 [0001.832] W> No valid slot number is found in scratch register [0001.838] W> Return default slot: _a [0001.841] I> Linux Cmdline: root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3576/nfsroot fbcon=map:0 net.ifnames=0 console=tty0 OS=l4t console=ttyS0,115200n8 memtype=0 video=tegrafb no_console_suspend=1 earlycon=uart8250,mmio32,0x03100000 nvdumper_reserved=0xf7fc0000 gpt androidboot.secureos=none tegraid=18.1.2.0.0 tegra_keep_boot_clocks maxcpus=6 android.kerneltype=normal androidboot.serialno=0330117020898 androidboot.security=non-secure sdhci_tegra.en_boot_part_access=1 [0001.890] I> Updated bootarg info to DTB [0001.895] I> eeprom_get_mac_addr: MAC (type: 0): 00:04:4b:81:c6:4e [0001.901] I> eeprom_get_mac_addr: MAC (type: 1): 00:04:4b:81:c6:4f [0001.907] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:81:c6:50 [0001.913] E> "ids" doesn't exist, creating [0001.917] E> "connection" doesn't exist, creating [0001.922] E> "configs" doesn't exist, creating [0001.926] I> create_pm_ids: id: 3310-1000-B00-B, len: 15 [0001.932] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.942] I> create_pm_ids: id: 2597-0000-500-C, len: 15 [0001.948] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.959] I> create_pm_ids: id: 3326-1000-000-M, len: 15 [0001.964] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0001.975] I> Adding plugin-manager/ids/3310-1000-B00=/i2c@c250000:module@0x50 [0001.982] E> "i2c@c250000" doesn't exist, creating [0001.986] E> "module@0x50" doesn't exist, creating [0001.991] I> Adding plugin-manager/ids/2597-0000-500=/i2c@c250000:module@0x57 [0001.998] E> "module@0x57" doesn't exist, creating [0002.003] I> Adding plugin-manager/ids/3326-1000-000=/i2c@3180000:module@0x54 [0002.010] E> "i2c@3180000" doesn't exist, creating [0002.015] E> "module@0x54" doesn't exist, creating [0002.021] I> Adding plugin-manager/ids/3310-1000-B00-B [0002.028] I> Adding plugin-manager/configs/3310-mem-type 00 [0002.034] I> Adding plugin-manager/configs/3310-power-config 00 [0002.040] I> Adding plugin-manager/configs/3310-misc-config 00 [0002.045] I> Adding plugin-manager/configs/3310-modem-config 00 [0002.051] I> Adding plugin-manager/configs/3310-touch-config 00 [0002.057] I> Adding plugin-manager/configs/3310-display-config 00 [0002.063] E> "chip-id" doesn't exist, creating [0002.068] I> Adding plugin-manager/chip-id/A02P [0002.074] I> Updated memory info to DTB [0002.079] E> "reset" doesn't exist, creating [0002.084] E> "pmc-reset-reason" doesn't exist, creating [0002.089] E> "pmic-reset-reason" doesn't exist, creating [0002.094] I> disabled_core_mask: 0xffffff0c [0002.105] I> tegrabl_load_kernel_and_dtb: Done U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:46:37 -0700) TEGRA186 Model: NVIDIA P2771-0000-500 DRAM: 7.8 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@2490000 Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2771-0000 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6266481 bytes read in 209 ms (28.6 MiB/s) Retrieving file: /boot/Image 17115648 bytes read in 456 ms (35.8 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3576/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra186-p2771-0000.dtb 23528 bytes read in 52 ms (441.4 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 0000000082008be7 Starting kernel ... [ 1.542764] console [ttyS0] enabled [ 1.542764] console [ttyS0] enabled [ 1.549871] bootconsole [uart0] disabled [ 1.549871] bootconsole [uart0] disabled [ 1.558243] SuperH (H)SCI(F) driver initialized [ 1.562981] msm_serial: driver initialized [ 1.567528] arm-smmu 12000000.iommu: probing hardware configuration... [ 1.574053] arm-smmu 12000000.iommu: SMMUv2 with: [ 1.578752] arm-smmu 12000000.iommu: stage 1 translation [ 1.584145] arm-smmu 12000000.iommu: stage 2 translation [ 1.589537] arm-smmu 12000000.iommu: nested translation [ 1.594845] arm-smmu 12000000.iommu: stream matching with 128 register groups [ 1.602058] arm-smmu 12000000.iommu: 64 context banks (0 stage-2 only) [ 1.608666] arm-smmu 12000000.iommu: Supported page sizes: 0x61311000 [ 1.615185] arm-smmu 12000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.621709] arm-smmu 12000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.628660] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.638101] loop: module loaded [ 1.643222] libphy: Fixed MDIO Bus: probed [ 1.647483] tun: Universal TUN/TAP device driver, 1.6 [ 1.652910] thunder-xcv, ver 1.0 [ 1.656162] thunder-BGX, ver 1.0 [ 1.659407] thunder-nic, ver 1.0 [ 1.662796] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.668622] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.674557] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.681508] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.687099] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.694917] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.701004] sky2: driver version 1.30 [ 1.705243] dwc-eth-dwmac 2490000.ethernet: Cannot get CSR clock [ 1.711282] dwc-eth-dwmac 2490000.ethernet: no reset control found [ 1.730562] stmmac - user ID: 0x10, Synopsys ID: 0x41 [ 1.735615] dwc-eth-dwmac 2490000.ethernet: DMA HW capability register supported [ 1.743003] dwc-eth-dwmac 2490000.ethernet: RX Checksum Offload Engine supported [ 1.750388] dwc-eth-dwmac 2490000.ethernet: TX Checksum insertion supported [ 1.757342] dwc-eth-dwmac 2490000.ethernet: Wake-Up On Lan supported [ 1.763702] dwc-eth-dwmac 2490000.ethernet: TSO supported [ 1.769094] dwc-eth-dwmac 2490000.ethernet: TSO feature enabled [ 1.775005] dwc-eth-dwmac 2490000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 1.782960] libphy: stmmac: probed [ 1.787252] VFIO - User Level meta-driver version: 0.3 [ 1.792991] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.799515] ehci-pci: EHCI PCI platform driver [ 1.803970] ehci-platform: EHCI generic platform driver [ 1.809257] ehci-orion: EHCI orion driver [ 1.813316] ehci-exynos: EHCI EXYNOS driver [ 1.817540] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.823718] ohci-pci: OHCI PCI platform driver [ 1.828175] ohci-platform: OHCI generic platform driver [ 1.833452] ohci-exynos: OHCI EXYNOS driver [ 1.837876] usbcore: registered new interface driver usb-storage [ 1.845222] i2c /dev entries driver [ 1.850643] max77620 0-003c: PMIC Version OTP:0x45 and ES:0x8 [ 1.861022] max77620-sd0: supplied by regulator-dummy [ 1.866222] VDD_DDR_1V1_PMIC: Bringing 1125000uV into 1100000-1100000uV [ 1.874815] max77620-sd1: supplied by regulator-dummy [ 1.881238] max77620-sd2: supplied by regulator-dummy [ 1.887660] max77620-sd3: supplied by regulator-dummy [ 1.894247] max77620-ldo0: supplied by regulator-dummy [ 1.900206] max77620-ldo1: supplied by regulator-dummy [ 1.906118] max77620-ldo2: supplied by regulator-dummy [ 1.912368] max77620-ldo3: supplied by regulator-dummy [ 1.918147] max77620-ldo4: supplied by regulator-dummy [ 1.923302] VDD_RTC: Bringing 800000uV into 1000000-1000000uV [ 1.929806] max77620-ldo5: supplied by regulator-dummy [ 1.934957] VDDIO_SDMMC3_AP: Bringing 1800000uV into 2800000-2800000uV [ 1.942105] max77620-ldo6: supplied by regulator-dummy [ 1.947870] max77620-ldo7: supplied by regulator-dummy [ 1.953017] VDD_HDMI_1V05: Bringing 1000000uV into 1050000-1050000uV [ 1.960588] max77620-ldo8: supplied by regulator-dummy [ 1.965734] VDD_PEX_1V05: Bringing 1000000uV into 1050000-1050000uV [ 3.147448] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.157015] sdhci: Secure Digital Host Controller Interface driver [ 3.163193] sdhci: Copyright(c) Pierre Ossman [ 3.167658] Synopsys Designware Multimedia Card Interface Driver [ 3.174088] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.179899] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 3.184699] sdhci-tegra 3400000.sdhci: Got WP GPIO [ 3.206418] mmc0: Unknown controller version (4). You may experience problems. [ 3.245252] mmc0: SDHCI controller on 3440000.sdhci [3440000.sdhci] using ADMA [ 3.262080] ledtrig-cpu: registered to indicate activity on CPUs [ 3.269399] usbcore: registered new interface driver usbhid [ 3.275522] usbhid: USB HID core driver [ 3.280580] NET: Registered protocol family 17 [ 3.285089] 9pnet: Installing 9P2000 support [ 3.289368] Key type dns_resolver registered [ 3.293964] registered taskstats version 1 [ 3.298074] Loading compiled-in X.509 certificates [ 3.309364] VDD_1V8_AP: supplied by VDD_1V8 [ 3.313905] SD_CARD_SW_PWR: supplied by VDD_3V3_SYS [ 3.319976] pca953x 1-0074: 1-0074 supply vcc not found, using dummy regulator [ 3.341571] pca953x 1-0077: 1-0077 supply vcc not found, using dummy regulator [ 3.359113] tegra-pcie 10003000.pcie: 4x1, 1x1 configuration [ 3.366293] tegra-pcie 10003000.pcie: probing port 0, using 4 lanes [ 3.374573] tegra-pcie 10003000.pcie: Slot present pin change, signature: 00000018 [ 3.788812] tegra-pcie 10003000.pcie: link 0 down, retrying [ 4.197508] tegra-pcie 10003000.pcie: link 0 down, retrying [ 4.606208] tegra-pcie 10003000.pcie: link 0 down, retrying [ 4.613782] tegra-pcie 10003000.pcie: link 0 down, ignoring [ 4.619417] tegra-pcie 10003000.pcie: PCI host bridge to bus 0000:00 [ 4.625769] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 4.631943] pci_bus 0000:00: root bus resource [mem 0x50100000-0x57ffffff] [ 4.638810] pci_bus 0000:00: root bus resource [mem 0x58000000-0x7fffffff pref] [ 4.646111] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.652032] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 4.656835] sdhci-tegra 3400000.sdhci: Got WP GPIO [ 4.669919] mmc1: Unknown controller version (4). You may experience problems. [ 4.708655] mmc1: SDHCI controller on 3400000.sdhci [3400000.sdhci] using ADMA [ 4.724917] mmc2: Unknown controller version (4). You may experience problems. [ 4.732630] mmc2: Switching to 3.3V signalling voltage failed [ 4.763985] mmc2: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA [ 4.772500] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 4.777983] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.802064] max77686-rtc max77620-rtc: setting system clock to 2016-11-08 12:14:47 UTC (1478607287) [ 4.811306] dwc-eth-dwmac 2490000.ethernet eth0: device MAC address 1e:80:dc:b5:04:2f [ 4.819621] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 4.830356] dwmac4: Master AXI performs any burst length [ 4.834990] mmc2: new high speed MMC card at address 0001 [ 4.835426] mmcblk2: mmc2:0001 032G34 29.1 GiB [ 4.835754] mmcblk2boot0: mmc2:0001 032G34 partition 1 4.00 MiB [ 4.836066] mmcblk2boot1: mmc2:0001 032G34 partition 2 4.00 MiB [ 4.836163] mmcblk2rpmb: mmc2:0001 032G34 partition 3 4.00 MiB, chardev (240:0) [ 4.837610] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [ 4.872189] dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 4.880697] dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock [ 8.992098] dwc-eth-dwmac 2490000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 9.023285] IP-Config: Complete: [ 9.026507] device=eth0, hwaddr=1e:80:dc:b5:04:2f, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 9.036667] host=192.168.99.2, domain=, nis-domain=(none) [ 9.042492] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 9.064850] VDD_RTC: disabling [ 9.067919] VDDIO_SDMMC3_AP: disabling [ 9.071817] SD_CARD_SW_PWR: disabling [ 9.075478] VDD_HDMI_5V0: disabling [ 9.078957] ALSA device list: [ 9.081921] No soundcards found. [ 9.085810] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 12:14:51 ] L4T-INITRD Build DATE: Tue Nov 8 12:14:51 UTC 2016 [ 12:14:51 ] Root device found: nfs [ 12:14:51 ] Ethernet interfaces: eth0 [ 12:14:51 ] IP Address: 192.168.99.2 [ 12:14:51 ] Rootfs mounted over nfs [ 12:14:51 ] Switching from initrd to actual rootfs [ 9.935733] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.953978] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 10.020543] systemd[1]: Set hostname to . [ 10.590788] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 10.607390] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.623378] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 10.639327] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.655410] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 10.675397] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 10.695485] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on udev Control Socket. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... Starting Create Static Device Nodes in /dev... Mounting Huge Pages File System... Mounting RPC Pipe File System... Mounting Debug File System... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting POSIX Message Queue File System... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. Starting Journal Service... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Mounting Configuration File System... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ 11.330515] systemd-journald[1506]: Received request to flush runtime journal from PID 1 Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Preprocess NFS configuration. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ 13.263044] systemd-update-[2516]: undefined instruction: pc=00000000cb23c836 [ 13.270184] Code: d2803202 52800001 a9017bf5 9100a3f3 (f945aa94) [FAILED] Failed to start Update UTMP about System Boot/Shutdown. See 'systemctl status systemd-update-utmp.service' for details. [DEPEND] Dependency failed for Update UTMP about System Runlevel Changes. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily apt activities. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. Starting /etc/rc.local Compatibility... Starting LSB: Start NTP daemon... Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting System Logging Service... [ OK ] Started D-Bus System Message Bus. Starting Permit User Sessions... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting OpenBSD Secure Shell server... [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started LSB: Start NTP daemon. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: [0000.183] I> Welcome to MB2(TBoot-BPMP)(version: 01.00.160913-t186-M-00.00-mobile-f4c42291) [0000.191] I> Default Heap @ [0xd486400 - 0xd488400] [0000.196] I> DMA Heap @ [0x84900000 - 0x85300000] [0000.201] I> bit @ 0xd480000 [0000.204] I> BR-BCT relocated to 0xf7f20000 [0000.208] I> Boot-device: eMMC [0000.212] I> pmic: reset reason (nverc) : 0x10 [0000.216] I> Reading GPT from 512 for device 00000003 [0000.222] I> Reading GPT from 8388096 for device 00000003 [0000.229] I> Found 6 partitions in 00000003 device [0000.234] I> Reading GPT from 512 for device 00010003 [0000.240] I> Found 17 partitions in 00010003 device [0000.246] W> No valid slot number is found in scratch register [0000.251] W> Return default slot: _a [0000.255] I> A/B: bin_type (16) slot 0 [0000.258] I> Select partition: bpmp-fw [0000.262] I> Loading partition bpmp-fw at 0xf7600000 [0000.267] I> Reading two headers - addr:0xf7600000 blocks:1 [0000.272] I> Addr: 0xf7600000, start-block: 58739717, num_blocks: 1 [0000.287] I> Binary(16) of size 524480 is loaded @ 0xf7600000 [0000.293] W> No valid slot number is found in scratch register [0000.298] W> Return default slot: _a [0000.302] I> A/B: bin_type (17) slot 0 [0000.305] I> Select partition: bpmp-fw-dtb [0000.309] I> Loading partition bpmp-fw-dtb at 0xf77f0000 [0000.314] I> Reading two headers - addr:0xf77f0000 blocks:1 [0000.320] I> Addr: 0xf77f0000, start-block: 58740925, num_blocks: 1 [0000.332] I> Binary(17) of size 326672 is loaded @ 0xf77b0200 [0000.459] I> BPMP-FW load address = 0xf7600000 [0000.464] I> BPMP-FW DTB load address = 0x501b0200 [0000.468] I> Loading SCE-FW ... [0000.471] W> No valid slot number is found in scratch register [0000.477] W> Return default slot: _a [0000.481] I> A/B: bin_type (12) slot 0 [0000.484] I> Select partition: sce-fw [0000.488] I> Loading partition sce-fw at 0xf7800000 [0000.492] I> Reading two headers - addr:0xf7800000 blocks:1 [0000.498] I> Addr: 0xf7800000, start-block: 58741925, num_blocks: 1 [0000.506] I> Binary(12) of size 65088 is loaded @ 0xf7800000 [0000.512] I> Init SCE [0000.514] I> Copy BTCM section [0000.517] W> No valid slot number is found in scratch register [0000.523] W> Return default slot: _a [0000.526] I> A/B: bin_type (13) slot 0 [0000.530] I> Select partition: cpu-bootloader [0000.534] I> Loading partition cpu-bootloader at 0x96000000 [0000.539] I> Reading two headers - addr:0x96000000 blocks:1 [0000.545] I> Addr: 0x96000000, start-block: 58732545, num_blocks: 1 [0000.555] I> Binary(13) of size 195776 is loaded @ 0x96000000 [0000.561] W> No valid slot number is found in scratch register [0000.566] W> Return default slot: _a [0000.570] I> A/B: bin_type (20) slot 0 [0000.574] I> Select partition: bootloader-dtb [0000.578] I> Loading partition bootloader-dtb at 0x85300000 [0000.583] I> Reading two headers - addr:0x85300000 blocks:1 [0000.589] I> Addr: 0x85300000, start-block: 58733057, num_blocks: 1 [0000.600] I> Binary(20) of size 248128 is loaded @ 0x85300000 [0000.605] I> MB2-params @ 0xf7f00000 [0000.609] I> CPUBL-params @ 0xf7f00000 [0000.612] I> CPU-BL loaded at : 0x96000000 [0000.616] I> Loading TOS ... [0000.619] W> No valid slot number is found in scratch register [0000.625] W> Return default slot: _a [0000.628] I> A/B: bin_type (14) slot 0 [0000.632] I> Select partition: secure-os [0000.636] I> Loading partition secure-os at 0x8490f400 [0000.641] I> Reading two headers - addr:0x8490f400 blocks:1 [0000.646] I> Addr: 0x8490f400, start-block: 58733569, num_blocks: 1 [0000.654] I> Binary(14) of size 54384 is loaded @ 0x8490f400 [0000.660] I> Copying Monitor (length: 0xd270) from 0x8490f600 to 0x40000000 [0000.667] I> Erasing Monitor @ 0x8490f600 [0000.671] I> Unhalting SCE [0000.675] I> Waypoint2-ACK: 0x5200b8d0 [0000.679] I> MB2(TBoot-BPMP) done NOTICE: BL31: v1.2(release):ff7a644 NOTICE: BL31: Built : 21:06:35, Mar 1 2017 NOTICE: Trusty image missing. ERROR: Error initializing runtime service trusty_fast [0001.042] I> Welcome to Cboot [0001.044] I> Cboot Version: 00.00.2014.50-t186-fabbc56c [0001.049] I> CPU-BL Params @ 0xf7f00000 [0001.053] I> 0) Base:0x00000000 Size:0x00000000 [0001.057] I> 1) Base:0xf7e00000 Size:0x00100000 [0001.062] I> 2) Base:0xf7d00000 Size:0x00100000 [0001.066] I> 3) Base:0xf7c00000 Size:0x00100000 [0001.071] I> 4) Base:0xf7b00000 Size:0x00100000 [0001.075] I> 5) Base:0xf7a00000 Size:0x00100000 [0001.080] I> 6) Base:0xf7600000 Size:0x00200000 [0001.084] I> 7) Base:0xf7000000 Size:0x00400000 [0001.088] I> 8) Base:0xf7900000 Size:0x00100000 [0001.093] I> 9) Base:0xf7800000 Size:0x00100000 [0001.097] I> 10) Base:0xf6800000 Size:0x00800000 [0001.102] I> 11) Base:0x30000000 Size:0x00040000 [0001.106] I> 12) Base:0xf7500000 Size:0x00100000 [0001.111] I> 13) Base:0x30040000 Size:0x00001000 [0001.115] I> 14) Base:0x30048000 Size:0x00001000 [0001.119] I> 15) Base:0x30049000 Size:0x00001000 [0001.124] I> 16) Base:0x3004a000 Size:0x00001000 [0001.128] I> 17) Base:0x3004b000 Size:0x00001000 [0001.133] I> 18) Base:0x3004c000 Size:0x00001000 [0001.137] I> 19) Base:0x3004d000 Size:0x00001000 [0001.142] I> 20) Base:0x3004e000 Size:0x00001000 [0001.146] I> 21) Base:0x3004f000 Size:0x00001000 [0001.150] I> 22) Base:0x00000000 Size:0x00000000 [0001.155] I> 23) Base:0xf7ff0000 Size:0x00010000 [0001.159] I> 24) Base:0x00000000 Size:0x00000000 [0001.164] I> 25) Base:0x00000000 Size:0x00000000 [0001.168] I> 26) Base:0x00000000 Size:0x00000000 [0001.173] I> 27) Base:0x00000000 Size:0x00000000 [0001.177] I> 28) Base:0x84400000 Size:0x00400000 [0001.181] I> 29) Base:0x30000000 Size:0x00010000 [0001.186] I> 30) Base:0xf8000000 Size:0x08000000 [0001.190] I> 31) Base:0x00000000 Size:0x00000000 [0001.195] I> 32) Base:0xf6000000 Size:0x00600000 [0001.199] I> 33) Base:0x80000000 Size:0x76000000 [0001.204] I> 34) Base:0x100000000 Size:0x180000000 [0001.208] I> 35) Base:0x00000000 Size:0x00000000 [0001.213] I> 36) Base:0x00000000 Size:0x00000000 [0001.217] I> 37) Base:0xf7fc0000 Size:0x00020000 [0001.221] I> 38) Base:0x84000000 Size:0x00400000 [0001.226] I> 39) Base:0x96000000 Size:0x02000000 [0001.230] I> 40) Base:0x84800000 Size:0x00b00000 [0001.235] I> 41) Base:0xf7f00000 Size:0x00080000 [0001.239] I> 42) Base:0x00000000 Size:0x00000000 [0001.244] I> 43) Base:0x00000000 Size:0x00000000 [0001.248] platform_init_interrupts-121, 1* [0001.252] Interrupts Init done [0001.255] calling constructors [0001.259] initializing heap [0001.261] initializing threads [0001.264] initializing timers [0001.267] creating bootstrap completion thread [0001.272] top of bootstrap2() [0001.275] CPU: ARM Cortex A57 [0001.278] CPU: MIDR: 0x411FD073, MPIDR: 0x80000100 [0001.283] initializing platform [0001.287] I> Boot-device: eMMC [0001.290] I> odm data is 1090000 [0001.293] I> Reading GPT from 512 for device 00000003 [0001.299] I> Reading GPT from 8388096 for device 00000003 [0001.305] I> Found 6 partitions in 00000003 device [0001.310] I> Reading GPT from 512 for device 00010003 [0001.316] I> Found 17 partitions in 00010003 device [0001.321] W> No valid slot number is found in scratch register [0001.326] W> Return default slot: _a [0001.330] I> A/B: bin_type (1) slot 0 [0001.333] I> Select partition: kernel-dtb [0001.337] I> Loading partition kernel-dtb at 0x92000000 [0001.346] I> Kernel_dtb @0x92000000 [0001.349] I> Bl_dtb @0x85300000 [0001.352] I> gpio framework initialized [0001.356] I> tegrabl_gpio_driver_register: register 'tegra_gpio_main_driver' driver [0001.363] I> tegrabl_gpio_driver_register: register 'tegra_gpio_aon_driver' driver [0001.371] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0001.379] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.386] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0001.394] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.402] E> tegrabl_blob_init: BMP partition does not have valid Blob [0001.409] E> tegrabl_load_bmp_blob: BMP blob initialization failed [0001.415] W> Loading bmp blob to memory failed [0001.423] I> Find /i2c@c250000's alias i2c7 [0001.427] I> Reading eeprom i2c=7 address=0x50 [0001.456] I> Device at /i2c@c250000:0x50 [0001.460] I> Reading eeprom i2c=7 address=0x57 [0001.489] I> Device at /i2c@c250000:0x57 [0001.494] I> Find /i2c@c240000's alias i2c1 [0001.498] I> Reading eeprom i2c=1 address=0x51 [0001.504] I> Eeprom read failed 0x1a800027 [0001.508] I> Find /i2c@3160000's alias i2c0 [0001.512] I> Reading eeprom i2c=0 address=0x50 [0001.517] I> Eeprom read failed 0x1a800027 [0001.522] I> Find /i2c@3180000's alias i2c2 [0001.526] I> Reading eeprom i2c=2 address=0x54 [0001.530] I> Enabling gpio chip_id = 2, gpio pin = 9 [0001.561] I> Disabling gpio chip_id = 2, gpio pin = 9 [0001.566] I> Device at /i2c@3180000:0x54 [0001.570] I> create_pm_ids: id: 3310-1000-B00-B, len: 15 [0001.575] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.586] I> create_pm_ids: id: 2597-0000-500-C, len: 15 [0001.591] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.602] I> create_pm_ids: id: 3326-1000-000-M, len: 15 [0001.607] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0001.618] initializing target [0001.621] calling apps_init() [0001.624] starting app android_boot_app [0001.628] I> Gpio keyboard init success [0001.632] I> Kernel type = Normal [0001.635] I> Loading kernel/boot.img ... [0001.639] W> No valid slot number is found in scratch register [0001.645] W> Return default slot: _a [0001.648] I> A/B: bin_type (0) slot 0 [0001.651] I> Select partition: kernel [0001.655] I> Loading partition kernel at 0xa8000000 [0001.736] W> No valid slot number is found in scratch register [0001.742] W> Return default slot: _a [0001.745] I> A/B: bin_type (1) slot 0 [0001.749] I> Select partition: kernel-dtb [0001.753] I> Loading partition kernel-dtb at 0x92000000 [0001.761] I> Kernel DTB @ 0x92000000 [0001.765] I> Verified boot state = Orange [0001.769] E> tegrabl_display_clear: display is not initialized [0001.774] I> Checking boot.img header magic ... [0001.779] I> [OK] [0001.780] I> Valid boot.img @ 0xa8000000 [0001.784] I> decompressor handler not found [0001.788] I> Copying kernel image (465664 bytes) from 0xa8000800 to 0x80080000 ... [0001.795] I> Done [0001.797] I> Move ramdisk (len: 6266481) from 0xa8072800 to 0x98000000 [0001.807] I> Updated bpmp info to DTB [0001.812] I> Ramdisk: Base: 0x98000000; Size: 0x5f9e71 [0001.817] I> Updated initrd info to DTB [0001.821] I> disabled_core_mask: 0xffffff0c [0001.825] I> Kernel type = Normal [0001.828] I> add_serialno: Serial Num = 0330117020898 [0001.833] W> No valid slot number is found in scratch register [0001.839] W> Return default slot: _a [0001.842] I> Linux Cmdline: root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3576/nfsroot fbcon=map:0 net.ifnames=0 console=tty0 OS=l4t console=ttyS0,115200n8 memtype=0 video=tegrafb no_console_suspend=1 earlycon=uart8250,mmio32,0x03100000 nvdumper_reserved=0xf7fc0000 gpt androidboot.secureos=none tegraid=18.1.2.0.0 tegra_keep_boot_clocks maxcpus=6 android.kerneltype=normal androidboot.serialno=0330117020898 androidboot.security=non-secure sdhci_tegra.en_boot_part_access=1 [0001.890] I> Updated bootarg info to DTB [0001.896] I> eeprom_get_mac_addr: MAC (type: 0): 00:04:4b:81:c6:4e [0001.902] I> eeprom_get_mac_addr: MAC (type: 1): 00:04:4b:81:c6:4f [0001.908] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:81:c6:50 [0001.914] E> "ids" doesn't exist, creating [0001.918] E> "connection" doesn't exist, creating [0001.923] E> "configs" doesn't exist, creating [0001.927] I> create_pm_ids: id: 3310-1000-B00-B, len: 15 [0001.932] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.943] I> create_pm_ids: id: 2597-0000-500-C, len: 15 [0001.948] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.959] I> create_pm_ids: id: 3326-1000-000-M, len: 15 [0001.964] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0001.975] I> Adding plugin-manager/ids/3310-1000-B00=/i2c@c250000:module@0x50 [0001.982] E> "i2c@c250000" doesn't exist, creating [0001.987] E> "module@0x50" doesn't exist, creating [0001.992] I> Adding plugin-manager/ids/2597-0000-500=/i2c@c250000:module@0x57 [0001.999] E> "module@0x57" doesn't exist, creating [0002.004] I> Adding plugin-manager/ids/3326-1000-000=/i2c@3180000:module@0x54 [0002.011] E> "i2c@3180000" doesn't exist, creating [0002.015] E> "module@0x54" doesn't exist, creating [0002.022] I> Adding plugin-manager/ids/3310-1000-B00-B [0002.029] I> Adding plugin-manager/configs/3310-mem-type 00 [0002.034] I> Adding plugin-manager/configs/3310-power-config 00 [0002.040] I> Adding plugin-manager/configs/3310-misc-config 00 [0002.046] I> Adding plugin-manager/configs/3310-modem-config 00 [0002.052] I> Adding plugin-manager/configs/3310-touch-config 00 [0002.058] I> Adding plugin-manager/configs/3310-display-config 00 [0002.064] E> "chip-id" doesn't exist, creating [0002.068] I> Adding plugin-manager/chip-id/A02P [0002.074] I> Updated memory info to DTB [0002.080] E> "reset" doesn't exist, creating [0002.084] E> "pmc-reset-reason" doesn't exist, creating [0002.089] E> "pmic-reset-reason" doesn't exist, creating [0002.095] I> disabled_core_mask: 0xffffff0c [0002.105] I> tegrabl_load_kernel_and_dtb: Done U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:46:37 -0700) TEGRA186 Model: NVIDIA P2771-0000-500 DRAM: 7.8 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@2490000 Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2771-0000 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6266481 bytes read in 209 ms (28.6 MiB/s) Retrieving file: /boot/Image 17115648 bytes read in 456 ms (35.8 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3576/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra186-p2771-0000.dtb 23528 bytes read in 52 ms (441.4 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 0000000082008be7 Starting kernel ... [ 1.540613] console [ttyS0] enabled [ 1.540613] console [ttyS0] enabled [ 1.547710] bootconsole [uart0] disabled [ 1.547710] bootconsole [uart0] disabled [ 1.556071] SuperH (H)SCI(F) driver initialized [ 1.560844] msm_serial: driver initialized [ 1.565395] arm-smmu 12000000.iommu: probing hardware configuration... [ 1.571919] arm-smmu 12000000.iommu: SMMUv2 with: [ 1.576622] arm-smmu 12000000.iommu: stage 1 translation [ 1.582014] arm-smmu 12000000.iommu: stage 2 translation [ 1.587406] arm-smmu 12000000.iommu: nested translation [ 1.592714] arm-smmu 12000000.iommu: stream matching with 128 register groups [ 1.599926] arm-smmu 12000000.iommu: 64 context banks (0 stage-2 only) [ 1.606536] arm-smmu 12000000.iommu: Supported page sizes: 0x61311000 [ 1.613055] arm-smmu 12000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.619573] arm-smmu 12000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.626512] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.635948] loop: module loaded [ 1.641085] libphy: Fixed MDIO Bus: probed [ 1.645495] tun: Universal TUN/TAP device driver, 1.6 [ 1.650911] thunder-xcv, ver 1.0 [ 1.654160] thunder-BGX, ver 1.0 [ 1.657407] thunder-nic, ver 1.0 [ 1.660800] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.666626] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.672563] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.679514] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.685104] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.692922] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.699008] sky2: driver version 1.30 [ 1.703248] dwc-eth-dwmac 2490000.ethernet: Cannot get CSR clock [ 1.709281] dwc-eth-dwmac 2490000.ethernet: no reset control found [ 1.728603] stmmac - user ID: 0x10, Synopsys ID: 0x41 [ 1.733656] dwc-eth-dwmac 2490000.ethernet: DMA HW capability register supported [ 1.741044] dwc-eth-dwmac 2490000.ethernet: RX Checksum Offload Engine supported [ 1.748429] dwc-eth-dwmac 2490000.ethernet: TX Checksum insertion supported [ 1.755387] dwc-eth-dwmac 2490000.ethernet: Wake-Up On Lan supported [ 1.761744] dwc-eth-dwmac 2490000.ethernet: TSO supported [ 1.767140] dwc-eth-dwmac 2490000.ethernet: TSO feature enabled [ 1.773054] dwc-eth-dwmac 2490000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 1.781008] libphy: stmmac: probed [ 1.785331] VFIO - User Level meta-driver version: 0.3 [ 1.791060] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.797599] ehci-pci: EHCI PCI platform driver [ 1.802059] ehci-platform: EHCI generic platform driver [ 1.807344] ehci-orion: EHCI orion driver [ 1.811398] ehci-exynos: EHCI EXYNOS driver [ 1.815628] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.821804] ohci-pci: OHCI PCI platform driver [ 1.826262] ohci-platform: OHCI generic platform driver [ 1.831536] ohci-exynos: OHCI EXYNOS driver [ 1.835987] usbcore: registered new interface driver usb-storage [ 1.843351] i2c /dev entries driver [ 1.848761] max77620 0-003c: PMIC Version OTP:0x45 and ES:0x8 [ 1.859136] max77620-sd0: supplied by regulator-dummy [ 1.864338] VDD_DDR_1V1_PMIC: Bringing 1125000uV into 1100000-1100000uV [ 1.872922] max77620-sd1: supplied by regulator-dummy [ 1.879343] max77620-sd2: supplied by regulator-dummy [ 1.885759] max77620-sd3: supplied by regulator-dummy [ 1.892334] max77620-ldo0: supplied by regulator-dummy [ 1.898294] max77620-ldo1: supplied by regulator-dummy [ 1.904188] max77620-ldo2: supplied by regulator-dummy [ 1.910440] max77620-ldo3: supplied by regulator-dummy [ 1.916224] max77620-ldo4: supplied by regulator-dummy [ 1.921381] VDD_RTC: Bringing 800000uV into 1000000-1000000uV [ 1.927877] max77620-ldo5: supplied by regulator-dummy [ 1.933026] VDDIO_SDMMC3_AP: Bringing 1800000uV into 2800000-2800000uV [ 1.940173] max77620-ldo6: supplied by regulator-dummy [ 1.945938] max77620-ldo7: supplied by regulator-dummy [ 1.951086] VDD_HDMI_1V05: Bringing 1000000uV into 1050000-1050000uV [ 1.958665] max77620-ldo8: supplied by regulator-dummy [ 1.963812] VDD_PEX_1V05: Bringing 1000000uV into 1050000-1050000uV [ 3.145383] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.154943] sdhci: Secure Digital Host Controller Interface driver [ 3.161121] sdhci: Copyright(c) Pierre Ossman [ 3.165587] Synopsys Designware Multimedia Card Interface Driver [ 3.172008] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.177815] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 3.182611] sdhci-tegra 3400000.sdhci: Got WP GPIO [ 3.204345] mmc0: Unknown controller version (4). You may experience problems. [ 3.243055] mmc0: SDHCI controller on 3440000.sdhci [3440000.sdhci] using ADMA [ 3.257832] ledtrig-cpu: registered to indicate activity on CPUs [ 3.264412] usbcore: registered new interface driver usbhid [ 3.269981] usbhid: USB HID core driver [ 3.274854] NET: Registered protocol family 17 [ 3.279342] 9pnet: Installing 9P2000 support [ 3.283624] Key type dns_resolver registered [ 3.288218] registered taskstats version 1 [ 3.292313] Loading compiled-in X.509 certificates [ 3.304668] VDD_1V8_AP: supplied by VDD_1V8 [ 3.309300] SD_CARD_SW_PWR: supplied by VDD_3V3_SYS [ 3.314832] pca953x 1-0074: 1-0074 supply vcc not found, using dummy regulator [ 3.332160] pca953x 1-0077: 1-0077 supply vcc not found, using dummy regulator [ 3.351232] tegra-pcie 10003000.pcie: 4x1, 1x1 configuration [ 3.357930] tegra-pcie 10003000.pcie: probing port 0, using 4 lanes [ 3.366213] tegra-pcie 10003000.pcie: Slot present pin change, signature: 00000018 [ 3.767633] tegra-pcie 10003000.pcie: link 0 down, retrying [ 4.176299] tegra-pcie 10003000.pcie: link 0 down, retrying [ 4.584957] tegra-pcie 10003000.pcie: link 0 down, retrying [ 4.592532] tegra-pcie 10003000.pcie: link 0 down, ignoring [ 4.598164] tegra-pcie 10003000.pcie: PCI host bridge to bus 0000:00 [ 4.604515] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 4.610690] pci_bus 0000:00: root bus resource [mem 0x50100000-0x57ffffff] [ 4.617559] pci_bus 0000:00: root bus resource [mem 0x58000000-0x7fffffff pref] [ 4.624862] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.630802] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 4.635600] sdhci-tegra 3400000.sdhci: Got WP GPIO [ 4.648694] mmc1: Unknown controller version (4). You may experience problems. [ 4.687328] mmc1: SDHCI controller on 3400000.sdhci [3400000.sdhci] using ADMA [ 4.703581] mmc2: Unknown controller version (4). You may experience problems. [ 4.711212] mmc2: Switching to 3.3V signalling voltage failed [ 4.742488] mmc2: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA [ 4.750987] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 4.756456] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.795920] max77686-rtc max77620-rtc: setting system clock to 2016-11-08 12:15:49 UTC (1478607349) [ 4.797152] mmc2: new high speed MMC card at address 0001 [ 4.797554] mmcblk2: mmc2:0001 032G34 29.1 GiB [ 4.797878] mmcblk2boot0: mmc2:0001 032G34 partition 1 4.00 MiB [ 4.798197] mmcblk2boot1: mmc2:0001 032G34 partition 2 4.00 MiB [ 4.798292] mmcblk2rpmb: mmc2:0001 032G34 partition 3 4.00 MiB, chardev (240:0) [ 4.799812] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [ 4.841540] dwc-eth-dwmac 2490000.ethernet eth0: device MAC address 4a:a5:95:7e:b0:f2 [ 4.849862] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 4.860590] dwmac4: Master AXI performs any burst length [ 4.866007] dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 4.874539] dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock [ 8.965517] dwc-eth-dwmac 2490000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 8.992698] IP-Config: Complete: [ 8.995920] device=eth0, hwaddr=4a:a5:95:7e:b0:f2, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 9.006080] host=192.168.99.2, domain=, nis-domain=(none) [ 9.011905] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 9.037312] VDD_RTC: disabling [ 9.040360] VDDIO_SDMMC3_AP: disabling [ 9.044252] SD_CARD_SW_PWR: disabling [ 9.047913] VDD_HDMI_5V0: disabling [ 9.051399] ALSA device list: [ 9.054361] No soundcards found. [ 9.058247] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 12:15:53 ] L4T-INITRD Build DATE: Tue Nov 8 12:15:53 UTC 2016 [ 12:15:53 ] Root device found: nfs [ 12:15:53 ] Ethernet interfaces: eth0 [ 12:15:53 ] IP Address: 192.168.99.2 [ 12:15:53 ] Rootfs mounted over nfs [ 12:15:53 ] Switching from initrd to actual rootfs [ 9.349999] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 9.368300] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 9.390150] systemd[1]: Set hostname to . [ 9.781405] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 9.800835] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 9.816830] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 9.836770] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 9.852787] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 9.868813] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.884836] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Created slice User and Session Slice. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice System Slice. Starting Remount Root and Kernel File Systems... Mounting POSIX Message Queue File System... Mounting Debug File System... Mounting RPC Pipe File System... Starting Journal Service... [ OK ] Created slice system-getty.slice. [ OK ] Reached target Slices. Starting Create Static Device Nodes in /dev... Starting Load Kernel Modules... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Reached target Swap. Mounting Huge Pages File System... [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load Kernel Modules. Starting Apply Kernel Variables... Mounting Configuration File System... Starting udev Kernel Device Manager... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started udev Coldplug all Devices. [ OK ] Found device /dev/ttyS0. [ 10.601784] systemd-journald[1500]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Permit User Sessions... Starting Login Service... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting System Logging Service... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... [ OK ] Started Regular background program processing daemon. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: