Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.35 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.9 sec Percent passed so far: 100.0 Final Score: 100.0 [0026.775] Enabled early print [0026.778] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0026.783] Processing in recovery mode [0026.786] A02 Bootrom Patch rev = 15 [0026.790] Power-up reason: pmc por [0026.793] Established communication link with host [0027.757] Odmdata from BCT: 0x00084000 [0027.761] DebugPort= 0x3 [0027.763] BoardId read from EEPROM/NCT: 2180 [0027.791] Turned on fan for loki board [0027.795] Key release before reqd. time for fastboot [0027.800] No Battery Present [0027.802] RamCode = 0 [0027.805] Platform has Ddr4 type ram [0027.808] max77620 disabling SD1 Remote Sense [0027.812] Setting Ddr voltage to 1125mv [0027.816] Serial Number of Pmic Max77663: 0xf1ba8 [0027.824] Entering ramdump check [0027.827] Get RamDumpCarveOut = 0x0 [0027.830] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0027.835] Last reboot was clean, booting normally! [0027.840] Sdram initialization is successful [0027.844] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0027.850] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0027.855] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0027.860] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0027.865] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0027.870] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0027.875] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0027.881] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0027.896] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0027.902] Platform-DebugCarveout: 0 [0027.905] Downloaded Bct successfully [0027.999] Downloaded bootloader successfully at 0x92c00000 [0028.092] Downloaded rp1 successfully at 0x83000000 [0028.140] MAX77620_GPIO1 Configured. [0028.144] MAX77620_GPIO5 Configured. [0028.147] CPU power rail is up [0028.150] CPU clock enabled [0028.154] Performing RAM repair [0028.157] Updating A64 Warmreset Address to 0x92c002e9 [0028.163] Enable APE clock/reset [0028.166] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0028.171] Loading Secure OS image failed. [0028.175] Set NvDecSticky Bits [0028.178] GSC1 address : ff700000 [0028.182] GSC2 address ff63fffc value c0edbbcc [0028.187] GSC2 address : ff600000 [0028.190] GSC3 address : ff500000 [0028.194] GSC4 address : ff400000 [0028.198] GSC5 address : ff300000 [0028.201] GSC MC Settings done [0028.204] NvTbootPackSdramParams: start. [0028.209] NvTbootPackSdramParams: done. [0028.213] Next binary entry address: 0x92c00258 [0028.217] BoardId: 2180 [0028.220] dram memory type is 3 [0028.223] Tegraboot started after 27417775 us [0028.227] Basic modules init took -27417775 us [0028.232] USB data transfer took 0 us [0028.235] Carveout took 28897231 us [0028.238] CPU initialization took 3629 us [0028.242] Total time taken by TegraBoot 1483085 us [0028.247] Starting CPU & Halting co-processor [0028.934] [0028.935] Debug Init done [0028.938] Marked DTB cacheable [0028.941] Bootloader DTB loaded at 0x83000000 [0028.945] DeviceTree Init done [0028.959] Pinmux applied successfully [0028.964] gicd_base: 0x50041000 [0028.968] gicc_base: 0x50042000 [0028.971] Interrupts Init done [0028.976] Using base:0x60005008 & irq:33 for tick-timer [0028.981] Using base:0x60005000 for delay-timer [0028.985] platform_init_timer: DONE [0028.989] Timer(tick) Init done [0028.993] osc freq = 38400 khz [0028.997] [0028.998] welcome to cboot [0029.001] [0029.002] Cboot Version: 24.00.2015.42-t210-63d15635 [0029.007] calling constructors [0029.010] initializing heap [0029.013] initializing threads [0029.016] initializing timers [0029.019] creating bootstrap completion thread [0029.023] top of bootstrap2() [0029.026] CPU: ARM Cortex A57 [0029.029] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0029.034] initializing platform [0029.070] config for ddr50 mode completed [0029.074] sdmmc bdev is already initialized [0029.078] of_register: registering tegra_udc to of_hal [0029.083] of_register: registering inv20628-driver to of_hal [0029.089] of_register: registering ads1015-driver to of_hal [0029.094] of_register: registering lp8557-bl-driver to of_hal [0029.100] of_register: registering bq2419x_charger to of_hal [0029.106] of_register: registering cpc to of_hal [0029.110] of_register: registering bq27441_fuel_gauge to of_hal [0029.124] gpio framework initialized [0029.128] of_register: registering tca9539_gpio to of_hal [0029.133] of_register: registering tca9539_gpio to of_hal [0029.139] of_register: registering i2c_bus_driver to of_hal [0029.144] of_register: registering i2c_bus_driver to of_hal [0029.150] of_register: registering i2c_bus_driver to of_hal [0029.155] pmic framework initialized [0029.159] of_register: registering max77620_pmic to of_hal [0029.164] regulator framework initialized [0029.168] of_register: registering tps65132_bl_driver to of_hal [0029.174] of_register: registering tegra_xhci to of_hal [0029.179] initializing target [0029.186] gpio_driver_register: register 'tegra_gpio_driver' driver [0029.196] fixed regulator driver initialized [0029.260] initializing OF layer [0029.265] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0029.273] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.295] I2C Bus Init done [0029.297] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.309] I2C Bus Init done [0029.312] of_children_init: Ops found for compatible string ti,lp8557 [0029.319] of_children_init: Ops found for compatible string ti,tca9539 [0029.330] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0029.336] gpio_driver_register: register 'tca9539_gpio_driver' driver [0029.342] of_children_init: Ops found for compatible string ti,tca9539 [0029.353] tca9539_init: i2c bus: 2, slave addr: 0xee [0029.359] gpio_driver_register: register 'tca9539_gpio_driver' driver [0029.365] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.377] I2C Bus Init done [0029.380] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.392] I2C Bus Init done [0029.395] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.407] I2C Bus Init done [0029.409] of_children_init: Ops found for compatible string maxim,max77620 [0029.422] max77620_init using irq 118 [0029.426] register 'maxim,max77620' pmic [0029.431] gpio_driver_register: register 'max77620-gpio' driver [0029.437] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0029.449] I2C Bus Init done [0029.452] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0029.461] calling apps_init() [0029.467] Found 30 GPT partitions in "sdmmc3_user" [0029.472] Proceeding to flashing Server [0029.475] usbdcd_reinit Initialize driver to use already enumerated device [0029.482] nv3p_priv_usbf_open USB configuration success [0029.489] Writing GPT partition [0029.493] Erasing Boot device [0029.523] Erasing Storage Device [0030.436] Sanitizing Storage Device [0030.655] Writing protective mbr [0030.660] Writing primary GPT [0030.665] Writing secondary GPT [0030.671] Found 18 GPT partitions in "sdmmc3_user" [0030.676] Writing NVC partition [0030.679] bct_init bctinit [0030.682] bct_init bctinit [0030.690] bct_init bctinit [0030.693] bct_init bctinit [0030.695] bct_init bctinit [0030.732] partition NVC write successful. [0030.737] Writing APP partition [0030.740] bct_init bctinit [0031.572] bct_init bctinit [0031.575] bct_init bctinit [0032.198] partition APP write successful. [0032.204] Writing TBC partition [0032.207] bct_init bctinit [0032.212] bct_init bctinit [0032.214] bct_init bctinit [0032.220] partition TBC write successful. [0032.224] Writing EBT partition [0032.227] bct_init bctinit [0032.246] bct_init bctinit [0032.249] bct_init bctinit [0032.260] partition EBT write successful. [0032.264] Writing BPF partition [0032.267] bct_init bctinit [0032.272] bct_init bctinit [0032.275] bct_init bctinit [0032.280] partition BPF write successful. [0032.285] Writing WB0 partition [0032.288] bct_init bctinit [0032.291] bct_init bctinit [0032.293] bct_init bctinit [0032.298] partition WB0 write successful. [0032.302] Writing RP1 partition [0032.305] bct_init bctinit [0032.321] bct_init bctinit [0032.324] bct_init bctinit [0032.333] partition RP1 write successful. [0032.338] Writing TOS partition [0032.341] bct_init bctinit [0032.346] bct_init bctinit [0032.349] bct_init bctinit [0032.354] partition TOS write successful. [0032.359] Writing DTB partition [0032.362] bct_init bctinit [0032.378] bct_init bctinit [0032.380] bct_init bctinit [0032.391] partition DTB write successful. [0032.399] Writing BCT partition [0032.403] bct_init bctinit [0032.502] partition BCT write successful. [0032.510] Change state to cold boot mode [0032.513] Flushing data to stroage [0000.154] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.159] Processing in cold boot mode Bootloader 2 [0000.164] A02 Bootrom Patch rev = 15 [0000.167] Power-up reason: software reset [0000.171] No Battery Present [0000.173] RamCode = 0 [0000.176] Platform has Ddr4 type ram [0000.179] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.187] Serial Number of Pmic Max77663: 0xf1ba8 [0000.195] Entering ramdump check [0000.198] Get RamDumpCarveOut = 0x0 [0000.201] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.206] Last reboot was clean, booting normally! [0000.211] Sdram initialization is successful [0000.215] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.226] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.231] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.236] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.241] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.246] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.267] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.272] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.313] Using GPT Primary to query partitions [0000.318] Loading Tboot-CPU binary [0000.367] Verifying bootloader in OdmNonSecureSBK mode [0000.377] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.384] Bootloader downloaded successfully. [0000.388] Downloaded Tboot-CPU binary to 0xa0000258 [0000.393] MAX77620_GPIO1 Configured. [0000.397] MAX77620_GPIO5 Configured. [0000.400] CPU power rail is up [0000.403] CPU clock enabled [0000.407] Performing RAM repair [0000.410] Updating A64 Warmreset Address to 0xa00002e9 [0000.427] Bootloader DTB Load Address: 0x83000000 [0000.443] Kernel DTB Load Address: 0x83080000 [0000.448] Loading cboot binary [0000.542] Verifying bootloader in OdmNonSecureSBK mode [0000.648] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.655] Bootloader downloaded successfully. [0000.659] GPT: Partition NOT found ! [0000.662] Find Partition via GPT Failed [0000.666] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.674] Error in NvTbootLoadBinary: 0x1 ! [0000.678] Next binary entry address: 0x80110000 [0000.683] BoardId: 2180 [0000.688] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.721] Set NvDecSticky Bits [0000.724] GSC1 address : ff700000 [0000.728] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.736] GSC3 address : ff500000 [0000.740] GSC4 address : ff400000 [0000.744] GSC5 address : ff300000 [0000.747] GSC MC Settings done [0000.750] TOS old plaintext Image length 65536 [0000.757] *** Secure OS image signature not verified *** [0000.762] Loading and Validation of Secure OS Successful [0000.767] NvTbootPackSdramParams: start. [0000.772] NvTbootPackSdramParams: done. [0000.776] Tegraboot started after 132862 us [0000.780] Basic modules init took 292395 us [0000.784] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.789] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.797] Next stage binary read took 12214 us [0000.801] Carveout took 264410 us [0000.804] CPU initialization took 92771 us [0000.808] Total time taken by TegraBoot 661790 us [0000.813] Starting CPU & Halting co-processor 64b[0000.920] RamCode = 0 [0000.935] LPDDR4 Training: Read DT: Number of tables = 10 [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.945] EMC Training Skipped [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.953] EMC Training Skipped [0000.956] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.961] EMC Training Skipped [0000.964] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.987] EMC Training Successful [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.002] EMC Training Successful [0001.005] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.052] EMC Training Successful [0001.055] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.075] EMC Training Successful [0001.078] Switching to 800000 KHz Success [0001.084] DT Write: emc-table@40800 succeeded [0001.090] DT Write: emc-table@68000 succeeded [0001.097] DT Write: emc-table@102000 succeeded [0001.103] DT Write: emc-table@204000 succeeded [0001.110] DT Write: emc-table@408000 succeeded [0001.116] DT Write: emc-table@665600 succeeded [0001.122] DT Write: emc-table@800000 succeeded [0001.129] DT Write: emc-table@1065600 succeeded [0001.135] DT Write: emc-table@1331200 succeeded [0001.141] DT Write: emc-table@1600000 succeeded [0001.146] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 ÿ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.127] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 15 [0000.135] Power-up reason: reset button [0000.138] No Battery Present [0000.141] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.147] max77620 disabling SD1 Remote Sense [0000.151] Setting Ddr voltage to 1125mv [0000.155] Serial Number of Pmic Max77663: 0xf1ba8 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.169] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.174] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.214] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.219] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.240] Platform-DebugCarveout: 0 [0000.243] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.253] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.286] Loading Tboot-CPU binary [0000.335] Verifying bootloader in OdmNonSecureSBK mode [0000.345] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.352] Bootloader downloaded successfully. [0000.356] Downloaded Tboot-CPU binary to 0xa0000258 [0000.361] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.368] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.411] Kernel DTB Load Address: 0x83080000 [0000.416] Loading cboot binary [0000.510] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.630] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.642] Error in NvTbootLoadBinary: 0x1 ! [0000.646] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.659] WB0 init successful [0000.685] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.692] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.700] GSC2 address : ff600000 [0000.704] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.718] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99858 us [0000.747] Basic modules init took 292164 us [0000.751] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.757] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12214 us [0000.768] Carveout took 264406 us [0000.771] CPU initialization took 92771 us [0000.775] Total time taken by TegraBoot 661555 us [0000.780] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.903] LPDDR4 Training: Read DT: Number of tables = 10 [0000.908] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.913] EMC Training Skipped [0000.916] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.921] EMC Training Skipped [0000.924] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.929] EMC Training Skipped [0000.932] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.937] EMC Training Skipped [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.946] EMC Training Successful [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.955] EMC Training Successful [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.995] EMC Training Successful [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.020] EMC Training Successful [0001.023] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.042] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.058] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.071] DT Write: emc-table@204000 succeeded [0001.077] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.090] DT Write: emc-table@800000 succeeded [0001.096] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.109] DT Write: emc-table@1600000 succeeded [0001.113] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915792 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17183232 bytes read in 437 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3620/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 53 ms (967.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.451965] console [ttyS0] enabled [ 0.451965] console [ttyS0] enabled [ 0.459537] bootconsole [uart0] disabled [ 0.459537] bootconsole [uart0] disabled [ 0.468347] SuperH (H)SCI(F) driver initialized [ 0.473539] msm_serial: driver initialized [ 0.478418] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.489156] loop: module loaded [ 0.494392] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.506209] max77620-sd0: supplied by regulator-dummy [ 0.512561] max77620-sd1: supplied by regulator-dummy [ 0.518722] max77620-sd2: supplied by regulator-dummy [ 0.524649] max77620-sd3: supplied by regulator-dummy [ 0.531082] max77620-ldo0: supplied by regulator-dummy [ 0.537172] max77620-ldo1: supplied by regulator-dummy [ 0.542946] max77620-ldo2: supplied by regulator-dummy [ 0.548982] max77620-ldo3: supplied by regulator-dummy [ 0.554157] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.561062] max77620-ldo4: supplied by regulator-dummy [ 0.566236] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.572833] max77620-ldo5: supplied by regulator-dummy [ 0.578016] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.585029] max77620-ldo6: supplied by regulator-dummy [ 0.590201] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.597120] max77620-ldo7: supplied by regulator-dummy [ 0.603128] max77620-ldo8: supplied by regulator-dummy [ 0.617068] libphy: Fixed MDIO Bus: probed [ 0.622225] tun: Universal TUN/TAP device driver, 1.6 [ 0.628606] thunder-xcv, ver 1.0 [ 0.632181] thunder-BGX, ver 1.0 [ 0.635580] thunder-nic, ver 1.0 [ 0.639252] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.645223] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.651206] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.658207] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.663869] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.671737] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.678037] sky2: driver version 1.30 [ 0.682256] usbcore: registered new interface driver r8152 [ 0.688038] VFIO - User Level meta-driver version: 0.3 [ 0.698376] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.705261] ehci-pci: EHCI PCI platform driver [ 0.709772] ehci-platform: EHCI generic platform driver [ 0.715157] ehci-orion: EHCI orion driver [ 0.719353] ehci-exynos: EHCI EXYNOS driver [ 0.723674] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.729904] ohci-pci: OHCI PCI platform driver [ 0.734409] ohci-platform: OHCI generic platform driver [ 0.739779] ohci-exynos: OHCI EXYNOS driver [ 0.744819] usbcore: registered new interface driver usb-storage [ 0.885526] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.894058] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.901472] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.907878] i2c /dev entries driver [ 0.915798] sdhci: Secure Digital Host Controller Interface driver [ 0.922962] sdhci: Copyright(c) Pierre Ossman [ 0.927661] Synopsys Designware Multimedia Card Interface Driver [ 0.934700] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.940879] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.961741] mmc0: Unknown controller version (3). You may experience problems. [ 0.998289] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.007610] ledtrig-cpu: registered to indicate activity on CPUs [ 1.015362] usbcore: registered new interface driver usbhid [ 1.021842] usbhid: USB HID core driver [ 1.028248] NET: Registered protocol family 17 [ 1.033556] 9pnet: Installing 9P2000 support [ 1.037931] Key type dns_resolver registered [ 1.042903] registered taskstats version 1 [ 1.047202] Loading compiled-in X.509 certificates [ 1.058932] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.063989] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.069931] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.075359] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.081439] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.088250] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.093854] mmc0: new high speed MMC card at address 0001 [ 1.099265] RTL_5V: supplied by VDD_5V0_SYS [ 1.099574] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.109587] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.114214] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.114481] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.115877] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.116090] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.116162] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.116211] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.140744] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.167373] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.173960] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.174389] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.174551] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.194598] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.207904] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.616928] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.025990] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.435042] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.442535] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.448028] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.456220] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.865249] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.274307] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.683359] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.690851] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.696459] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.702764] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.708953] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.715834] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.723154] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.729102] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.737216] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.746573] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.814350] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.821748] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.827155] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.835721] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.844362] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.850836] hub 1-0:1.0: USB hub found [ 3.854699] hub 1-0:1.0: 5 ports detected [ 3.859106] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.864586] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.872239] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.880705] hub 2-0:1.0: USB hub found [ 3.884548] hub 2-0:1.0: 4 ports detected [ 3.889918] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.901853] mmc1: Unknown controller version (3). You may experience problems. [ 3.938364] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.946527] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.958693] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.966451] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.974030] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.986506] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.018244] max77686-rtc max77620-rtc: setting system clock to 2017-12-13 06:04:58 UTC (1513145098) [ 4.222206] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.249015] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.261948] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.386598] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.446920] r8152 2-1:1.0 eth0: v1.09.9 [ 4.451000] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.463144] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.592281] r8152 2-1:1.0 eth0: carrier on [ 7.613708] IP-Config: Complete: [ 7.616931] device=eth0, hwaddr=00:04:4b:56:bd:4d, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.627116] host=192.168.99.2, domain=, nis-domain=(none) [ 7.632945] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.640371] AVDD_DSI_CSI_1V2: disabling [ 7.644225] VDD_PRE_REG_1V35: disabling [ 7.648076] VDD_CAM_HV: disabling [ 7.651533] VDD_TS_HV: disabling [ 7.654880] VDD_TS_1V8: disabling [ 7.658223] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.662579] VDD_3V3_SD: disabling [ 7.665895] VDD_HDMI_5V0: disabling [ 7.669376] ALSA device list: [ 7.672339] No soundcards found. [ 7.676509] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 06:05:02 ] L4T-INITRD Build DATE: Wed Dec 13 06:05:02 UTC 2017 [ 06:05:02 ] Root device found: nfs [ 06:05:02 ] Ethernet interfaces: eth0 [ 06:05:02 ] IP Address: 192.168.99.2 [ 06:05:02 ] Rootfs mounted over nfs [ 06:05:02 ] Switching from initrd to actual rootfs [ 8.247483] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.265878] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.291400] systemd[1]: Set hostname to . [ 8.698672] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.717871] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.733756] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 8.749834] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.769847] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.785805] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.801793] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Swap. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. Starting Journal Service... Starting Create Static Device Nodes in /dev... Starting Remount Root and Kernel File Systems... Mounting Debug File System... Mounting RPC Pipe File System... Starting Load Kernel Modules... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting POSIX Message Queue File System... [ OK ] Reached target Slices. Mounting Huge Pages File System... [ OK ] Mounted Debug File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Journal Service. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... [ OK ] Reached target Local File Systems (Pre). Starting udev Coldplug all Devices... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started udev Kernel Device Manager. [ 9.665977] systemd-journald[1510]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting System Logging Service... Starting LSB: Start NTP daemon... [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting OpenBSD Secure Shell server... [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. Starting /etc/rc.local Compatibility... [ OK ] Started D-Bus System Message Bus. [ 11.143743] random: crng init done Starting Permit User Sessions... [ OK ] Started System Logging Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/ttyS0. [ OK ] Started Login Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ÿ[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.127] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 15 [0000.135] Power-up reason: reset button [0000.138] No Battery Present [0000.141] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.147] max77620 disabling SD1 Remote Sense [0000.151] Setting Ddr voltage to 1125mv [0000.155] Serial Number of Pmic Max77663: 0xf1ba8 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.169] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.174] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.188] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.193] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.214] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.219] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.240] Platform-DebugCarveout: 0 [0000.243] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.248] Non secure mode. Disable rollback prevention [0000.253] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.286] Loading Tboot-CPU binary [0000.335] Verifying bootloader in OdmNonSecureSBK mode [0000.345] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.352] Bootloader downloaded successfully. [0000.356] Downloaded Tboot-CPU binary to 0xa0000258 [0000.361] MAX77620_GPIO1 Configured. [0000.364] MAX77620_GPIO5 Configured. [0000.368] CPU power rail is up [0000.370] CPU clock enabled [0000.374] Performing RAM repair [0000.377] Updating A64 Warmreset Address to 0xa00002e9 [0000.394] Bootloader DTB Load Address: 0x83000000 [0000.411] Kernel DTB Load Address: 0x83080000 [0000.416] Loading cboot binary [0000.510] Verifying bootloader in OdmNonSecureSBK mode [0000.615] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.622] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.630] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.637] function NvTbootGetBinaryOffsets: 0x1 error [0000.642] Error in NvTbootLoadBinary: 0x1 ! [0000.646] Next binary entry address: 0x80110000 [0000.650] BoardId: 2180 [0000.655] dram memory type is 3 [0000.659] WB0 init successful [0000.685] Bpmp FW successfully loaded [0000.688] Set NvDecSticky Bits [0000.692] GSC1 address : ff700000 [0000.695] GSC2 address ff63fffc value c0edbbcc [0000.700] GSC2 address : ff600000 [0000.704] GSC3 address : ff500000 [0000.707] GSC4 address : ff400000 [0000.711] GSC5 address : ff300000 [0000.714] GSC MC Settings done [0000.718] TOS old plaintext Image length 65536 [0000.724] *** Secure OS image signature not verified *** [0000.729] Loading and Validation of Secure OS Successful [0000.734] NvTbootPackSdramParams: start. [0000.739] NvTbootPackSdramParams: done. [0000.743] Tegraboot started after 99827 us [0000.747] Basic modules init took 292165 us [0000.751] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.757] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.764] Next stage binary read took 12214 us [0000.768] Carveout took 264406 us [0000.771] CPU initialization took 92771 us [0000.775] Total time taken by TegraBoot 661556 us [0000.780] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.903] LPDDR4 Training: Read DT: Number of tables = 10 [0000.908] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.913] EMC Training Skipped [0000.916] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.921] EMC Training Skipped [0000.924] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.929] EMC Training Skipped [0000.932] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.937] EMC Training Skipped [0000.940] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.946] EMC Training Successful [0000.949] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.955] EMC Training Successful [0000.958] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.969] EMC Training Successful [0000.972] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.995] EMC Training Successful [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.023] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.042] EMC Training Successful [0001.045] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.058] DT Write: emc-table@68000 succeeded [0001.064] DT Write: emc-table@102000 succeeded [0001.071] DT Write: emc-table@204000 succeeded [0001.077] DT Write: emc-table@408000 succeeded [0001.083] DT Write: emc-table@665600 succeeded [0001.090] DT Write: emc-table@800000 succeeded [0001.096] DT Write: emc-table@1065600 succeeded [0001.102] DT Write: emc-table@1331200 succeeded [0001.109] DT Write: emc-table@1600000 succeeded [0001.113] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 431 bytes read in 70 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915792 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17183232 bytes read in 437 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl3620/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 53 ms (967.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.451718] console [ttyS0] enabled [ 0.451718] console [ttyS0] enabled [ 0.459314] bootconsole [uart0] disabled [ 0.459314] bootconsole [uart0] disabled [ 0.468101] SuperH (H)SCI(F) driver initialized [ 0.473281] msm_serial: driver initialized [ 0.478155] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.488911] loop: module loaded [ 0.494149] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.506007] max77620-sd0: supplied by regulator-dummy [ 0.512379] max77620-sd1: supplied by regulator-dummy [ 0.518527] max77620-sd2: supplied by regulator-dummy [ 0.524464] max77620-sd3: supplied by regulator-dummy [ 0.530907] max77620-ldo0: supplied by regulator-dummy [ 0.536994] max77620-ldo1: supplied by regulator-dummy [ 0.542758] max77620-ldo2: supplied by regulator-dummy [ 0.548798] max77620-ldo3: supplied by regulator-dummy [ 0.553975] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.560881] max77620-ldo4: supplied by regulator-dummy [ 0.566057] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.572652] max77620-ldo5: supplied by regulator-dummy [ 0.577837] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.584847] max77620-ldo6: supplied by regulator-dummy [ 0.590020] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.596937] max77620-ldo7: supplied by regulator-dummy [ 0.602947] max77620-ldo8: supplied by regulator-dummy [ 0.616891] libphy: Fixed MDIO Bus: probed [ 0.622050] tun: Universal TUN/TAP device driver, 1.6 [ 0.628454] thunder-xcv, ver 1.0 [ 0.632031] thunder-BGX, ver 1.0 [ 0.635426] thunder-nic, ver 1.0 [ 0.639099] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.645070] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.651055] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.658057] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.663719] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.671585] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.677884] sky2: driver version 1.30 [ 0.682142] usbcore: registered new interface driver r8152 [ 0.687895] VFIO - User Level meta-driver version: 0.3 [ 0.698276] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.705167] ehci-pci: EHCI PCI platform driver [ 0.709699] ehci-platform: EHCI generic platform driver [ 0.715127] ehci-orion: EHCI orion driver [ 0.719275] ehci-exynos: EHCI EXYNOS driver [ 0.723595] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.729822] ohci-pci: OHCI PCI platform driver [ 0.734330] ohci-platform: OHCI generic platform driver [ 0.739701] ohci-exynos: OHCI EXYNOS driver [ 0.744744] usbcore: registered new interface driver usb-storage [ 0.885565] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.894113] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.901527] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.907930] i2c /dev entries driver [ 0.916845] sdhci: Secure Digital Host Controller Interface driver [ 0.923103] sdhci: Copyright(c) Pierre Ossman [ 0.927867] Synopsys Designware Multimedia Card Interface Driver [ 0.934765] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.940966] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.961723] mmc0: Unknown controller version (3). You may experience problems. [ 0.998273] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.007599] ledtrig-cpu: registered to indicate activity on CPUs [ 1.015357] usbcore: registered new interface driver usbhid [ 1.021847] usbhid: USB HID core driver [ 1.028170] NET: Registered protocol family 17 [ 1.033527] 9pnet: Installing 9P2000 support [ 1.037926] Key type dns_resolver registered [ 1.042885] registered taskstats version 1 [ 1.047188] Loading compiled-in X.509 certificates [ 1.059000] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.064063] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.070005] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.075441] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.081506] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.088326] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.093883] mmc0: new high speed MMC card at address 0001 [ 1.099344] RTL_5V: supplied by VDD_5V0_SYS [ 1.099652] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.109667] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.114289] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.114558] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.115970] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.116182] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.116252] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.116301] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.140841] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.167466] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.174059] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.174490] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.174653] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.194714] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.208020] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.617057] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.026122] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.435172] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.442667] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.448163] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.456355] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.865398] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.274467] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.683529] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.691022] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.696632] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.702937] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.709128] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.716009] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.723328] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.729316] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.737413] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.746768] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.814331] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.821729] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.827136] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.835691] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.844334] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.850810] hub 1-0:1.0: USB hub found [ 3.854675] hub 1-0:1.0: 5 ports detected [ 3.859080] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.864563] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.872214] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.880673] hub 2-0:1.0: USB hub found [ 3.884518] hub 2-0:1.0: 4 ports detected [ 3.889905] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.901835] mmc1: Unknown controller version (3). You may experience problems. [ 3.938351] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.946516] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.958672] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.966422] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.974002] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.986482] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.018224] max77686-rtc max77620-rtc: setting system clock to 2017-12-13 06:05:59 UTC (1513145159) [ 4.222189] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.248992] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.261917] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.386581] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.446905] r8152 2-1:1.0 eth0: v1.09.9 [ 4.450983] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.463100] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.400267] r8152 2-1:1.0 eth0: carrier on [ 7.421688] IP-Config: Complete: [ 7.424912] device=eth0, hwaddr=00:04:4b:56:bd:4d, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.435096] host=192.168.99.2, domain=, nis-domain=(none) [ 7.440925] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.448349] AVDD_DSI_CSI_1V2: disabling [ 7.452204] VDD_PRE_REG_1V35: disabling [ 7.456056] VDD_CAM_HV: disabling [ 7.459514] VDD_TS_HV: disabling [ 7.462861] VDD_TS_1V8: disabling [ 7.466200] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.470556] VDD_3V3_SD: disabling [ 7.473872] VDD_HDMI_5V0: disabling [ 7.477350] ALSA device list: [ 7.480317] No soundcards found. [ 7.484465] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 06:06:02 ] L4T-INITRD Build DATE: Wed Dec 13 06:06:02 UTC 2017 [ 06:06:02 ] Root device found: nfs [ 06:06:02 ] Ethernet interfaces: eth0 [ 06:06:02 ] IP Address: 192.168.99.2 [ 06:06:02 ] Rootfs mounted over nfs [ 06:06:02 ] Switching from initrd to actual rootfs [ 7.735711] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.754100] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.774586] systemd[1]: Set hostname to . [ 8.084143] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.101759] systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 8.118018] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 8.133957] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.153921] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 8.169857] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.189903] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Listening on Syslog Socket. [ OK ] Reached target Slices. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Socket. Mounting POSIX Message Queue File System... Mounting Debug File System... Starting Load Kernel Modules... Mounting RPC Pipe File System... Mounting Huge Pages File System... [ OK ] Listening on udev Control Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Remount Root and Kernel File Systems... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Swap. Starting Create Static Device Nodes in /dev... [ OK ] Listening on Journal Audit Socket. Starting Journal Service... [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Journal Service. Starting udev Kernel Device Manager... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting udev Coldplug all Devices... Starting Apply Kernel Variables... Mounting Configuration File System... [ OK ] Started udev Kernel Device Manager. [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started Apply Kernel Variables. [ 8.895371] systemd-journald[1523]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... Starting Raise network interfaces... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily apt activities. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... Starting /etc/rc.local Compatibility... Starting Permit User Sessions... [ OK ] Started D-Bus System Message Bus. Starting LSB: Start NTP daemon... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting Login Service... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Started System Logging Service. [ OK ] Started Login Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Getty on tty1. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Found device /dev/ttyS0. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ 11.091839] random: crng init done Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: