U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.tegra_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.tegra_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################# 4 MiB/s done Bytes transferred = 6201632 (5ea120 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 4 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x5ea120 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.15.0-rc3-next-20171212-18839-gd207879 (jonathanh@kaivo) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP PREEMPT Mon Dec 11 21:46:54 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0xfbc00000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39104 r8192 d22336 u69632 [ 0.000000] pcpu-alloc: s39104 r8192 d22336 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1998492K/2096128K available (9216K kernel code, 778K rwdata, 2564K rodata, 1024K init, 298K bss, 32100K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 779 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 299 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.007459] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.016987] Switching to timer-based delay loop, resolution 1000ns [ 0.024163] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.029210] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.039958] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.047927] Switching to timer-based delay loop, resolution 83ns [ 0.054399] Console: colour dummy device 80x30 [ 0.058342] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.068651] pid_max: default: 32768 minimum: 301 [ 0.073728] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.079837] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.087683] CPU: Testing write buffer coherency: ok [ 0.092005] /cpus/cpu@0 missing clock-frequency property [ 0.097008] /cpus/cpu@1 missing clock-frequency property [ 0.102319] /cpus/cpu@2 missing clock-frequency property [ 0.107584] /cpus/cpu@3 missing clock-frequency property [ 0.112855] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152968] Setting up static identity map for 0x80100000 - 0x801000a0 [ 0.157721] Hierarchical SRCU implementation. [ 0.173478] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.192989] smp: Bringing up secondary CPUs ... [ 0.243541] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.323651] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.403763] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.413414] smp: Brought up 1 node, 4 CPUs [ 0.432502] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.438670] CPU: All CPU(s) started in SVC mode. [ 0.445091] devtmpfs: initialized [ 0.465774] Built 1 zonelists, mobility grouping on. Total pages: 516007 [ 0.471049] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.478630] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.488098] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.494488] pinctrl core: initialized pinctrl subsystem [ 0.500614] NET: Registered protocol family 16 [ 0.505096] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.512129] cpuidle: using governor menu [ 0.537286] No ATAGs? [ 0.537423] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.545784] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.553474] iommu: Adding device reg-dummy to group 0 [ 0.556676] iommu: Adding device 1003000.pcie to group 1 [ 0.561972] iommu: Adding device 50000000.host1x to group 2 [ 0.567533] iommu: Adding device 54200000.dc to group 3 [ 0.572714] iommu: Adding device 54240000.dc to group 4 [ 0.577900] iommu: Adding device 54280000.hdmi to group 5 [ 0.583288] iommu: Adding device 57000000.gpu to group 6 [ 0.588559] iommu: Adding device 60005000.timer to group 7 [ 0.593992] iommu: Adding device 60007000.flow-controller to group 8 [ 0.600345] iommu: Adding device 6000c800.actmon to group 9 [ 0.605868] iommu: Adding device 6000d000.gpio to group 10 [ 0.611344] iommu: Adding device 60020000.dma to group 11 [ 0.616702] iommu: Adding device 70000800.apbmisc to group 12 [ 0.622438] iommu: Adding device 70000868.pinmux to group 13 [ 0.628067] iommu: Adding device 70006000.serial to group 14 [ 0.633705] iommu: Adding device 70006040.serial to group 15 [ 0.639319] iommu: Adding device 70006300.serial to group 16 [ 0.644973] iommu: Adding device 7000c000.i2c to group 17 [ 0.650326] iommu: Adding device 7000c400.i2c to group 18 [ 0.655717] iommu: Adding device 7000c500.i2c to group 19 [ 0.661080] iommu: Adding device 7000c700.i2c to group 20 [ 0.666472] iommu: Adding device 7000d000.i2c to group 21 [ 0.671820] iommu: Adding device 7000d400.spi to group 22 [ 0.677212] iommu: Adding device 7000da00.spi to group 23 [ 0.682568] iommu: Adding device 7000e000.rtc to group 24 [ 0.687960] iommu: Adding device 7000e400.pmc to group 25 [ 0.693312] iommu: Adding device 7000f800.fuse to group 26 [ 0.698792] iommu: Adding device 70019000.memory-controller to group 27 [ 0.705361] iommu: Adding device 7001b000.emc to group 28 [ 0.710757] iommu: Adding device 70027000.sata to group 29 [ 0.716199] iommu: Adding device 70030000.hda to group 30 [ 0.721587] iommu: Adding device 70090000.usb to group 31 [ 0.726941] iommu: Adding device 7009f000.padctl to group 32 [ 0.732599] iommu: Adding device 700b0400.sdhci to group 33 [ 0.738120] iommu: Adding device 700b0600.sdhci to group 34 [ 0.743685] iommu: Adding device 70015000.cec to group 35 [ 0.749054] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.755389] iommu: Adding device 70110000.clock to group 37 [ 0.760913] iommu: Adding device 70300000.ahub to group 38 [ 0.766392] iommu: Adding device 7d000000.usb to group 39 [ 0.771746] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.777491] iommu: Adding device 7d004000.usb to group 41 [ 0.782841] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.788584] iommu: Adding device 7d008000.usb to group 43 [ 0.793933] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.799670] iommu: Adding device pmu to group 45 [ 0.804248] iommu: Adding device timer to group 46 [ 0.809012] iommu: Adding device clocks to group 47 [ 0.813884] iommu: Adding device gpio-keys to group 48 [ 0.818981] iommu: Adding device regulators to group 49 [ 0.824206] iommu: Adding device regulators:regulator@0 to group 50 [ 0.830420] iommu: Adding device regulators:regulator@1 to group 51 [ 0.836685] iommu: Adding device regulators:regulator@2 to group 52 [ 0.842900] iommu: Adding device regulators:regulator@3 to group 53 [ 0.849158] iommu: Adding device regulators:regulator@4 to group 54 [ 0.855380] iommu: Adding device regulators:regulator@7 to group 55 [ 0.861637] iommu: Adding device regulators:regulator@8 to group 56 [ 0.867868] iommu: Adding device regulators:regulator@10 to group 57 [ 0.874206] iommu: Adding device regulators:regulator@11 to group 58 [ 0.880513] iommu: Adding device regulators:regulator@12 to group 59 [ 0.886859] iommu: Adding device regulators:regulator@13 to group 60 [ 0.893167] iommu: Adding device regulators:regulator@14 to group 61 [ 0.899517] iommu: Adding device sound to group 62 [ 0.920962] +5V_SYS: supplied by +VDD_MUX [ 0.923446] +3.3V_SYS: supplied by +VDD_MUX [ 0.928007] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.933335] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.941456] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.947187] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.955411] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.962203] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.970400] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.976218] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.984439] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.989993] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.998217] +12V_SATA: Failed to request enable GPIO242: -517 [ 1.003858] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 1.013290] vgaarb: loaded [ 1.015455] SCSI subsystem initialized [ 1.018641] libata version 3.00 loaded. [ 1.022535] usbcore: registered new interface driver usbfs [ 1.027758] usbcore: registered new interface driver hub [ 1.033070] usbcore: registered new device driver usb [ 1.041242] Linux video capture interface: v2.00 [ 1.044021] pps_core: LinuxPPS API ver. 1 registered [ 1.048913] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.058026] PTP clock support registered [ 1.063323] Advanced Linux Sound Architecture Driver Initialized. [ 1.068614] Bluetooth: Core ver 2.22 [ 1.071558] NET: Registered protocol family 31 [ 1.075947] Bluetooth: HCI device and connection manager initialized [ 1.082259] Bluetooth: HCI socket layer initialized [ 1.087126] Bluetooth: L2CAP socket layer initialized [ 1.092168] Bluetooth: SCO socket layer initialized [ 1.097647] clocksource: Switched to clocksource arch_sys_counter [ 1.194354] NET: Registered protocol family 2 [ 1.197817] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 1.204492] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.211573] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.218061] TCP: Hash tables configured (established 8192 bind 8192) [ 1.224677] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.230145] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.236730] NET: Registered protocol family 1 [ 1.241476] RPC: Registered named UNIX socket transport module. [ 1.246634] RPC: Registered udp transport module. [ 1.251342] RPC: Registered tcp transport module. [ 1.255995] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.262874] iommu: Adding device regulatory.0 to group 63 [ 1.268049] PCI: CLS 0 bytes, default 64 [ 1.273510] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 1.280526] iommu: Adding device alarmtimer to group 64 [ 1.286150] Initialise system trusted keyrings [ 1.289647] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 1.297214] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.302495] NFS: Registering the id_resolver key type [ 1.306708] Key type id_resolver registered [ 1.310888] Key type id_legacy registered [ 1.319945] Key type asymmetric registered [ 1.322131] Asymmetric key parser 'x509' registered [ 1.327122] bounce: pool size: 64 pages [ 1.330881] io scheduler noop registered (default) [ 1.335565] io scheduler mq-deadline registered [ 1.340093] io scheduler kyber registered [ 1.345880] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.350886] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 1.357835] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 1.373710] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 1.377412] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 1.387312] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 1.397981] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.404924] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 1.410518] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.416324] iommu: Adding device serial8250 to group 65 [ 1.423214] console [ttyS0] disabled [ 1.424998] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.434317] console [ttyS0] enabled [ 1.434317] console [ttyS0] enabled [ 1.440144] bootconsole [earlycon0] disabled [ 1.440144] bootconsole [earlycon0] disabled [ 1.449504] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.460570] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.489137] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.508653] loop: module loaded [ 1.513206] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.520645] as3722 4-0040: AS3722 with revision 0x1 found [ 1.528269] iommu: Adding device as3722-pinctrl to group 66 [ 1.535523] iommu: Adding device as3722-regulator to group 67 [ 1.544210] as3722-sd2: supplied by +5V_SYS [ 1.548886] as3722-sd3: supplied by +5V_SYS [ 1.553301] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.559685] as3722-sd4: supplied by +5V_SYS [ 1.564352] as3722-sd5: supplied by +5V_SYS [ 1.570450] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.576550] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.582804] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.588751] as3722-ldo3: supplied by +3.3V_SYS [ 1.593252] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.601076] as3722-ldo4: supplied by +3.3V_SYS [ 1.605745] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.612006] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.616855] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.623833] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.629508] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.635688] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.645893] iommu: Adding device as3722-rtc to group 68 [ 1.651305] iommu: Adding device as3722-adc to group 69 [ 1.656673] iommu: Adding device as3722-power-off to group 70 [ 1.662589] iommu: Adding device as3722-wdt to group 71 [ 1.668589] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.687209] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.693918] iommu: Adding device Fixed MDIO bus.0 to group 72 [ 1.699879] libphy: Fixed MDIO Bus: probed [ 1.703971] CAN device driver interface [ 1.707878] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.714828] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.720564] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.728054] usbcore: registered new interface driver pegasus [ 1.733767] usbcore: registered new interface driver asix [ 1.739237] usbcore: registered new interface driver ax88179_178a [ 1.745378] usbcore: registered new interface driver cdc_ether [ 1.751292] usbcore: registered new interface driver smsc75xx [ 1.757096] usbcore: registered new interface driver smsc95xx [ 1.762908] usbcore: registered new interface driver net1080 [ 1.768640] usbcore: registered new interface driver cdc_subset [ 1.774610] usbcore: registered new interface driver zaurus [ 1.780266] usbcore: registered new interface driver cdc_ncm [ 1.786168] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.791819] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.797516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.804056] ehci-pci: EHCI PCI platform driver [ 1.808568] tegra-ehci: Tegra EHCI driver [ 1.815415] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.820852] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.828666] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 1.857679] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.864501] hub 1-0:1.0: USB hub found [ 1.868312] hub 1-0:1.0: 1 port detected [ 1.873469] usbcore: registered new interface driver cdc_acm [ 1.879140] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.887191] usbcore: registered new interface driver cdc_wdm [ 1.892952] usbcore: registered new interface driver usb-storage [ 1.900577] iommu: Adding device ci_hdrc.0 to group 73 [ 1.912512] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.919411] as3722-rtc as3722-rtc: RTC interrupt 379 [ 1.927185] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.934392] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.940923] i2c /dev entries driver [ 1.945634] usbcore: registered new interface driver uvcvideo [ 1.951395] USB Video Class driver (1.1.1) [ 1.955485] gspca_main: v2.14.0 registered [ 1.960245] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.970503] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) [ 1.979001] iommu: Adding device cpufreq-tegra124 to group 74 [ 1.985304] sdhci: Secure Digital Host Controller Interface driver [ 1.991496] sdhci: Copyright(c) Pierre Ossman [ 1.995847] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.001835] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.006730] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.028026] mmc0: Unknown controller version (3). You may experience problems. [ 2.035283] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.072426] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.080832] usbcore: registered new interface driver usbhid [ 2.086438] usbhid: USB HID core driver [ 2.092721] iommu: Adding device snd-soc-dummy to group 75 [ 2.135721] mmc0: new high speed MMC card at address 0001 [ 2.146383] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.156022] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.167113] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.173285] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (247:0) [ 2.182447] mmcblk0: p1 [ 2.538160] iommu: Adding device 70301100.i2s to group 76 [ 2.544452] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub [ 2.564765] tegra-snd-rt5640 sound: rt5640-aif1 <-> 70301100.i2s mapping ok [ 2.575573] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input0 [ 2.586794] NET: Registered protocol family 10 [ 2.592688] Segment Routing with IPv6 [ 2.596522] mip6: Mobile IPv6 [ 2.599512] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.606896] NET: Registered protocol family 17 [ 2.611423] NET: Registered protocol family 15 [ 2.615875] can: controller area network core (rev 20170425 abi 9) [ 2.622279] NET: Registered protocol family 29 [ 2.626719] can: raw protocol (rev 20170425) [ 2.631003] can: broadcast manager protocol (rev 20170425 t) [ 2.636661] can: netlink gateway (rev 20170425) max_hops=1 [ 2.642390] Bluetooth: RFCOMM socket layer initialized [ 2.647538] Bluetooth: RFCOMM ver 1.11 [ 2.651315] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.656626] Bluetooth: BNEP socket layer initialized [ 2.661603] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.667520] Bluetooth: HIDP socket layer initialized [ 2.672762] Key type dns_resolver registered [ 2.677525] Registering SWP/SWPB emulation handler [ 2.683127] Loading compiled-in X.509 certificates [ 2.705681] +3.3V_RUN: supplied by +3.3V_SYS [ 2.710829] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.715531] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.721555] +5V_USB_HS: supplied by +5V_SYS [ 2.726667] +3.3V_LP0: supplied by +3.3V_SYS [ 2.732019] +5V_HDMI_CON: supplied by +5V_SYS [ 2.736798] +5V_SATA: supplied by +5V_SYS [ 2.741483] +12V_SATA: supplied by +VDD_MUX [ 2.747085] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.753945] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.761134] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.768660] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.774273] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.783396] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.792407] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.800903] as3722-sd2: supplied by +5V_SYS [ 2.805400] as3722-sd3: supplied by +5V_SYS [ 2.809922] as3722-sd4: supplied by +5V_SYS [ 2.814389] as3722-sd5: supplied by +5V_SYS [ 2.820340] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.825812] as3722-ldo1: supplied by +3.3V_RUN [ 2.831010] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.836547] as3722-ldo3: supplied by +3.3V_SYS [ 2.842089] as3722-ldo4: supplied by +3.3V_SYS [ 2.846840] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.852710] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 [ 2.861260] as3722-ldo6: supplied by +3.3V_RUN [ 2.866250] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.871719] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.878830] as3722-ldo9: supplied by +5V_SYS [ 2.884295] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.891050] as3722-ldo10: supplied by +5V_SYS [ 2.896158] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.903027] as3722-ldo11: supplied by +3.3V_RUN [ 2.908055] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.917283] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.926362] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.936888] scsi host0: tegra-ahci [ 2.941336] scsi host1: tegra-ahci [ 2.945039] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.953085] ata2: DUMMY [ 2.956694] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.962177] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.970027] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 2.997780] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 3.004896] hub 2-0:1.0: USB hub found [ 3.008769] hub 2-0:1.0: 1 port detected [ 3.025679] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 [ 3.035489] tegra-xusb 70090000.usb: failed to request firmware: -2 [ 3.041805] tegra-xusb 70090000.usb: failed to load firmware: -2 [ 3.048533] tegra-xusb: probe of 70090000.usb failed with error -2 [ 3.055544] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 3.060493] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 3.071927] mmc1: Unknown controller version (3). You may experience problems. [ 3.079267] mmc1: Invalid maximum block size, assuming 512 bytes [ 3.117283] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 3.125034] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 3.132581] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 3.140575] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 3.165334] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 3.173693] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 3.187720] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.194002] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.200303] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.207285] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.214711] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.220306] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 3.226338] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.236108] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.245922] pci 0000:00:01.0: enabling Extended Tags [ 3.251011] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.260819] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.270734] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.277461] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.281189] ata1: SATA link down (SStatus 0 SControl 300) [ 3.293115] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.299183] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.308920] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.318738] pci 0000:00:02.0: enabling Extended Tags [ 3.323752] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.333530] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.343368] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.350128] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.360246] PCI: bus0: Fast back to back transfers disabled [ 3.365903] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.373986] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.382284] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.388416] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.395552] PCI: bus1: Fast back to back transfers disabled [ 3.401208] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.408104] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.414202] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.419889] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.426867] mmc1: new high speed SDHC card at address aaaa [ 3.432193] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.443016] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.450638] PCI: bus2: Fast back to back transfers disabled [ 3.456364] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.463183] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.470222] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.477253] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.485148] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.491415] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.498908] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.504052] mmcblk1: p1 p2 p3 [ 3.507251] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.514323] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.522356] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.530769] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.536868] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.541898] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.548054] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.554857] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.562682] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.569877] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.576319] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.582341] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.589528] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.595957] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.602147] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.607783] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.613657] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.649411] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xb9dcd63a, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.659000] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.671170] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.680581] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.687207] [drm] No driver support for vblank timestamp query. [ 3.827036] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.990298] Console: switching to colour frame buffer device 512x135 [ 4.086319] drm drm: fb0: frame buffer device [ 4.090903] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 4.098227] iommu: Adding device cpufreq-dt.0 to group 77 [ 4.103896] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 4.111242] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 4.120314] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [ 4.127571] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:13 UTC (946684813) [ 4.136336] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.146040] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.152758] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.158131] +USB0_VBUS_SW: disabling [ 4.158150] +1.8V_RUN_CAM: disabling [ 4.161505] +2.8V_RUN_CAM: disabling [ 4.165096] +1.2V_RUN_CAM_FRONT: disabling [ 4.168700] +1.05V_RUN_CAM_REAR: disabling [ 4.172294] +3.3V_RUN_TOUCH: disabling [ 4.176399] +2.8V_RUN_CAM_AF: disabling [ 4.180523] +1.8V_RUN_VPP_FUSE: disabling [ 4.184320] ALSA device list: [ 4.184325] #0: tegra-hda at 0x70038000 irq 346 [ 4.184326] #1: NVIDIA Tegra Jetson TK1 [ 4.203792] cfg80211: failed to load regulatory.db [ 4.209695] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.257006] EXT4-fs (mmcblk0p1): recovery complete [ 4.262822] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.270990] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.281997] devtmpfs: mounted [ 4.285334] Freeing unused kernel memory: 1024K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#