U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################## 3.9 MiB/s done Bytes transferred = 8118784 (7be200 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7be200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.15.0-rc2-next-20171211-338510-g153e8244ebcb (jonathanh@tamien) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Mon Dec 11 06:31:23 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39040 r8192 d22400 u69632 [ 0.000000] pcpu-alloc: s39040 r8192 d22400 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1992460K/2096128K available (11264K kernel code, 1582K rwdata, 4316K rodata, 2048K init, 404K bss, 38132K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1583 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 405 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000043] Switching to timer-based delay loop, resolution 1000ns [ 0.005643] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005663] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005682] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005697] Switching to timer-based delay loop, resolution 83ns [ 0.006185] Console: colour dummy device 80x30 [ 0.006219] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.006237] pid_max: default: 32768 minimum: 301 [ 0.006352] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006367] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006868] CPU: Testing write buffer coherency: ok [ 0.007135] /cpus/cpu@0 missing clock-frequency property [ 0.007181] /cpus/cpu@1 missing clock-frequency property [ 0.007225] /cpus/cpu@2 missing clock-frequency property [ 0.007271] /cpus/cpu@3 missing clock-frequency property [ 0.007285] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007583] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.009620] Hierarchical SRCU implementation. [ 0.011591] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.012401] EFI services will not be available. [ 0.012561] smp: Bringing up secondary CPUs ... [ 0.013128] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.016160] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.026181] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035641] smp: Brought up 1 node, 4 CPUs [ 0.035662] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035671] CPU: All CPU(s) started in SVC mode. [ 0.037186] devtmpfs: initialized [ 0.051643] Built 1 zonelists, mobility grouping on. Total pages: 514499 [ 0.052012] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.052432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.052451] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052641] pinctrl core: initialized pinctrl subsystem [ 0.054142] DMI not present or invalid. [ 0.054392] NET: Registered protocol family 16 [ 0.056437] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058960] cpuidle: using governor menu [ 0.084232] No ATAGs? [ 0.084360] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.084376] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.091983] Serial: AMBA PL011 UART driver [ 0.093395] iommu: Adding device reg-dummy to group 0 [ 0.093436] iommu: Adding device 1003000.pcie to group 1 [ 0.093511] iommu: Adding device 50000000.host1x to group 2 [ 0.093582] iommu: Adding device 54200000.dc to group 3 [ 0.093652] iommu: Adding device 54240000.dc to group 4 [ 0.093685] iommu: Adding device 54280000.hdmi to group 5 [ 0.093758] iommu: Adding device 57000000.gpu to group 6 [ 0.093794] iommu: Adding device 60005000.timer to group 7 [ 0.093826] iommu: Adding device 60007000.flow-controller to group 8 [ 0.093857] iommu: Adding device 6000c800.actmon to group 9 [ 0.093889] iommu: Adding device 6000d000.gpio to group 10 [ 0.093921] iommu: Adding device 60020000.dma to group 11 [ 0.093952] iommu: Adding device 70000800.apbmisc to group 12 [ 0.093983] iommu: Adding device 70000868.pinmux to group 13 [ 0.094014] iommu: Adding device 70006000.serial to group 14 [ 0.094044] iommu: Adding device 70006040.serial to group 15 [ 0.094079] iommu: Adding device 70006300.serial to group 16 [ 0.094115] iommu: Adding device 7000c000.i2c to group 17 [ 0.094146] iommu: Adding device 7000c400.i2c to group 18 [ 0.094177] iommu: Adding device 7000c500.i2c to group 19 [ 0.094207] iommu: Adding device 7000c700.i2c to group 20 [ 0.094238] iommu: Adding device 7000d000.i2c to group 21 [ 0.094269] iommu: Adding device 7000d400.spi to group 22 [ 0.094300] iommu: Adding device 7000da00.spi to group 23 [ 0.094333] iommu: Adding device 7000e000.rtc to group 24 [ 0.094365] iommu: Adding device 7000e400.pmc to group 25 [ 0.094395] iommu: Adding device 7000f800.fuse to group 26 [ 0.094431] iommu: Adding device 70019000.memory-controller to group 27 [ 0.094461] iommu: Adding device 7001b000.emc to group 28 [ 0.094491] iommu: Adding device 70027000.sata to group 29 [ 0.094523] iommu: Adding device 70030000.hda to group 30 [ 0.094558] iommu: Adding device 70090000.usb to group 31 [ 0.094589] iommu: Adding device 7009f000.padctl to group 32 [ 0.094624] iommu: Adding device 700b0400.sdhci to group 33 [ 0.094655] iommu: Adding device 700b0600.sdhci to group 34 [ 0.094685] iommu: Adding device 70015000.cec to group 35 [ 0.094715] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.094747] iommu: Adding device 70110000.clock to group 37 [ 0.094782] iommu: Adding device 70300000.ahub to group 38 [ 0.094813] iommu: Adding device 7d000000.usb to group 39 [ 0.094844] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.094879] iommu: Adding device 7d004000.usb to group 41 [ 0.094909] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.094939] iommu: Adding device 7d008000.usb to group 43 [ 0.094970] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.095000] iommu: Adding device pmu to group 45 [ 0.095030] iommu: Adding device timer to group 46 [ 0.095060] iommu: Adding device clocks to group 47 [ 0.095091] iommu: Adding device gpio-keys to group 48 [ 0.095130] iommu: Adding device regulators to group 49 [ 0.095161] iommu: Adding device regulators:regulator@0 to group 50 [ 0.095192] iommu: Adding device regulators:regulator@1 to group 51 [ 0.095223] iommu: Adding device regulators:regulator@2 to group 52 [ 0.095253] iommu: Adding device regulators:regulator@3 to group 53 [ 0.095284] iommu: Adding device regulators:regulator@4 to group 54 [ 0.095314] iommu: Adding device regulators:regulator@7 to group 55 [ 0.095345] iommu: Adding device regulators:regulator@8 to group 56 [ 0.095376] iommu: Adding device regulators:regulator@10 to group 57 [ 0.095411] iommu: Adding device regulators:regulator@11 to group 58 [ 0.095447] iommu: Adding device regulators:regulator@12 to group 59 [ 0.095478] iommu: Adding device regulators:regulator@13 to group 60 [ 0.095510] iommu: Adding device regulators:regulator@14 to group 61 [ 0.095544] iommu: Adding device sound to group 62 [ 0.110643] AT91: Could not find identification node [ 0.111210] +5V_SYS: supplied by +VDD_MUX [ 0.111488] +3.3V_SYS: supplied by +VDD_MUX [ 0.112094] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.112110] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.112208] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.112222] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.112403] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.112417] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.112512] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.112526] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.112620] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.112633] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.112728] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.112742] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.115793] vgaarb: loaded [ 0.116527] SCSI subsystem initialized [ 0.116704] libata version 3.00 loaded. [ 0.116899] usbcore: registered new interface driver usbfs [ 0.116946] usbcore: registered new interface driver hub [ 0.117019] usbcore: registered new device driver usb [ 0.120545] pps_core: LinuxPPS API ver. 1 registered [ 0.120557] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.120579] PTP clock support registered [ 0.120774] EDAC MC: Ver: 3.0.0 [ 0.123645] clocksource: Switched to clocksource arch_sys_counter [ 0.174346] NET: Registered protocol family 2 [ 0.174844] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.174876] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.174975] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.175162] TCP: Hash tables configured (established 8192 bind 8192) [ 0.175245] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.175289] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.175438] NET: Registered protocol family 1 [ 0.175760] RPC: Registered named UNIX socket transport module. [ 0.175772] RPC: Registered udp transport module. [ 0.175780] RPC: Registered tcp transport module. [ 0.175789] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.175802] PCI: CLS 0 bytes, default 64 [ 0.177283] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.178032] iommu: Adding device alarmtimer to group 63 [ 0.178826] Initialise system trusted keyrings [ 0.178954] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.185415] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.185982] NFS: Registering the id_resolver key type [ 0.186003] Key type id_resolver registered [ 0.186012] Key type id_legacy registered [ 0.186053] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.187546] Key type asymmetric registered [ 0.187557] Asymmetric key parser 'x509' registered [ 0.187609] bounce: pool size: 64 pages [ 0.187653] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.187665] io scheduler noop registered [ 0.187674] io scheduler deadline registered [ 0.187890] io scheduler cfq registered (default) [ 0.187900] io scheduler mq-deadline registered [ 0.187909] io scheduler kyber registered [ 0.191995] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.192113] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.192489] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.212023] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.212080] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.218552] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.225024] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.228436] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.277269] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.277364] iommu: Adding device serial8250 to group 64 [ 0.279863] console [ttyS0] disabled [ 0.279903] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.560515] console [ttyS0] enabled [ 1.564914] SuperH (H)SCI(F) driver initialized [ 1.570566] msm_serial: driver initialized [ 1.574883] STMicroelectronics ASC driver initialized [ 1.580620] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.589894] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.621167] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.638167] brd: module loaded [ 1.647453] loop: module loaded [ 1.651853] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.660205] as3722 4-0040: AS3722 with revision 0x1 found [ 1.667523] iommu: Adding device as3722-pinctrl to group 65 [ 1.674547] iommu: Adding device as3722-regulator to group 66 [ 1.683076] as3722-sd2: supplied by +5V_SYS [ 1.687767] as3722-sd3: supplied by +5V_SYS [ 1.692164] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.698496] as3722-sd4: supplied by +5V_SYS [ 1.703085] as3722-sd5: supplied by +5V_SYS [ 1.709050] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.715102] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.721267] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.727149] as3722-ldo3: supplied by +3.3V_SYS [ 1.731624] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.739386] as3722-ldo4: supplied by +3.3V_SYS [ 1.744072] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.750245] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.755094] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.761978] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.767651] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.773846] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.783734] iommu: Adding device as3722-rtc to group 67 [ 1.789280] iommu: Adding device as3722-adc to group 68 [ 1.794830] iommu: Adding device as3722-power-off to group 69 [ 1.800869] iommu: Adding device as3722-wdt to group 70 [ 1.807960] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.830449] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.837577] iommu: Adding device Fixed MDIO bus.0 to group 71 [ 1.843703] libphy: Fixed MDIO Bus: probed [ 1.848734] CAN device driver interface [ 1.853517] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.860617] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.866455] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.872417] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.879380] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.889050] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.896495] usbcore: registered new interface driver pegasus [ 1.902183] usbcore: registered new interface driver asix [ 1.907615] usbcore: registered new interface driver ax88179_178a [ 1.913740] usbcore: registered new interface driver cdc_ether [ 1.919599] usbcore: registered new interface driver smsc75xx [ 1.925395] usbcore: registered new interface driver smsc95xx [ 1.931157] usbcore: registered new interface driver net1080 [ 1.936850] usbcore: registered new interface driver cdc_subset [ 1.942785] usbcore: registered new interface driver zaurus [ 1.948415] usbcore: registered new interface driver cdc_ncm [ 1.954317] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.959911] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.967428] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.973962] ehci-pci: EHCI PCI platform driver [ 1.978432] ehci-platform: EHCI generic platform driver [ 1.983884] ehci-orion: EHCI orion driver [ 1.988057] SPEAr-ehci: EHCI SPEAr driver [ 1.992204] ehci-st: EHCI STMicroelectronics driver [ 1.997233] ehci-exynos: EHCI EXYNOS driver [ 2.001577] ehci-atmel: EHCI Atmel driver [ 2.005737] tegra-ehci: Tegra EHCI driver [ 2.012590] tegra-ehci 7d004000.usb: EHCI Host Controller [ 2.018026] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 2.025820] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 2.053670] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 2.060229] hub 1-0:1.0: USB hub found [ 2.064038] hub 1-0:1.0: 1 port detected [ 2.068515] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.074723] ohci-pci: OHCI PCI platform driver [ 2.079198] ohci-platform: OHCI generic platform driver [ 2.084638] SPEAr-ohci: OHCI SPEAr driver [ 2.088787] ohci-st: OHCI STMicroelectronics driver [ 2.093822] ohci-atmel: OHCI Atmel driver [ 2.098633] usbcore: registered new interface driver usb-storage [ 2.106457] iommu: Adding device ci_hdrc.0 to group 72 [ 2.118661] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 2.125554] as3722-rtc as3722-rtc: RTC interrupt 379 [ 2.133924] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 2.141097] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 2.147854] i2c /dev entries driver [ 2.158512] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 2.173829] iommu: Adding device cpufreq-tegra124 to group 73 [ 2.182040] sdhci: Secure Digital Host Controller Interface driver [ 2.188234] sdhci: Copyright(c) Pierre Ossman [ 2.194404] Synopsys Designware Multimedia Card Interface Driver [ 2.201970] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.208464] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.213352] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.234630] mmc0: Unknown controller version (3). You may experience problems. [ 2.241887] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.278852] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.288499] ledtrig-cpu: registered to indicate activity on CPUs [ 2.294857] usbcore: registered new interface driver usbhid [ 2.300421] usbhid: USB HID core driver [ 2.308532] NET: Registered protocol family 10 [ 2.313950] Segment Routing with IPv6 [ 2.317695] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.324233] NET: Registered protocol family 17 [ 2.328678] can: controller area network core (rev 20170425 abi 9) [ 2.334919] NET: Registered protocol family 29 [ 2.339357] can: raw protocol (rev 20170425) [ 2.343620] can: broadcast manager protocol (rev 20170425 t) [ 2.349295] can: netlink gateway (rev 20170425) max_hops=1 [ 2.355065] Key type dns_resolver registered [ 2.359839] ThumbEE CPU extension supported. [ 2.364133] Registering SWP/SWPB emulation handler [ 2.369488] Loading compiled-in X.509 certificates [ 2.387225] +3.3V_RUN: supplied by +3.3V_SYS [ 2.393001] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.397786] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.403956] +5V_USB_HS: supplied by +5V_SYS [ 2.410001] +3.3V_LP0: supplied by +3.3V_SYS [ 2.416312] +5V_HDMI_CON: supplied by +5V_SYS [ 2.421183] +5V_SATA: supplied by +5V_SYS [ 2.425899] +12V_SATA: supplied by +VDD_MUX [ 2.431465] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.438355] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.445409] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.453389] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.459101] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.468987] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.479444] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.490572] as3722-sd2: supplied by +5V_SYS [ 2.495139] as3722-sd3: supplied by +5V_SYS [ 2.499556] as3722-sd4: supplied by +5V_SYS [ 2.503997] as3722-sd5: supplied by +5V_SYS [ 2.510027] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.515914] as3722-ldo1: supplied by +3.3V_RUN [ 2.520724] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.526462] as3722-ldo3: supplied by +3.3V_SYS [ 2.531943] as3722-ldo4: supplied by +3.3V_SYS [ 2.536809] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.541728] as3722-ldo6: supplied by +3.3V_RUN [ 2.546455] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.551967] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.559256] as3722-ldo9: supplied by +5V_SYS [ 2.564915] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.571473] as3722-ldo10: supplied by +5V_SYS [ 2.576351] mmc0: new high speed MMC card at address 0001 [ 2.582358] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.587313] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.593603] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.599687] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (236:0) [ 2.607275] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.613886] as3722-ldo11: supplied by +3.3V_RUN [ 2.619167] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.627742] mmcblk0: p1 [ 2.633411] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.642496] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.652619] scsi host0: tegra-ahci [ 2.657281] scsi host1: tegra-ahci [ 2.660896] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.668947] ata2: DUMMY [ 2.675126] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.680543] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.688315] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 2.723770] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.730387] hub 2-0:1.0: USB hub found [ 2.734211] hub 2-0:1.0: 1 port detected [ 2.740741] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.745672] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.757885] mmc1: Unknown controller version (3). You may experience problems. [ 2.765227] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.803240] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.811510] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.819185] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.826893] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.852727] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.861069] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.875913] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.882181] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.888413] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.895331] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.902645] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.908211] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.914280] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.923979] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.933710] pci 0000:00:01.0: enabling Extended Tags [ 2.938690] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.948497] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.958307] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.964972] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.974995] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.981021] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.990709] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.997368] ata1: SATA link down (SStatus 0 SControl 300) [ 3.005827] pci 0000:00:02.0: enabling Extended Tags [ 3.010804] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.020607] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.030422] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.037053] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.047046] PCI: bus0: Fast back to back transfers disabled [ 3.052617] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.060643] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.068819] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.074894] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.081966] PCI: bus1: Fast back to back transfers disabled [ 3.087577] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.094363] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.100392] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.106019] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.112818] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.120214] PCI: bus2: Fast back to back transfers disabled [ 3.125801] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.132444] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.139244] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.146044] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.153794] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.159886] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.167223] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.172187] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.178995] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.186761] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.194095] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.200187] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.205167] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.211272] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.218093] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.225878] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.232972] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.239326] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.245251] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.252302] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.258626] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.264720] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.270304] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.276189] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.299282] mmc1: new high speed SDHC card at address aaaa [ 3.305417] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.315358] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xdc641605, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.325007] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.337747] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.345542] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.352156] [drm] No driver support for vblank timestamp query. [ 3.361797] mmcblk1: p1 p2 p3 [ 3.486977] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.650231] Console: switching to colour frame buffer device 512x135 [ 3.748866] drm drm: fb0: frame buffer device [ 3.753407] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.761105] iommu: Adding device cpufreq-dt.0 to group 74 [ 3.766996] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.774338] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.783577] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.790793] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:02:27 UTC (946684947) [ 3.799763] +USB0_VBUS_SW: disabling [ 3.803338] +1.8V_RUN_CAM: disabling [ 3.807181] +2.8V_RUN_CAM: disabling [ 3.810997] +1.2V_RUN_CAM_FRONT: disabling [ 3.815360] +1.05V_RUN_CAM_REAR: disabling [ 3.819647] +3.3V_RUN_TOUCH: disabling [ 3.823541] +2.8V_RUN_CAM_AF: disabling [ 3.827603] +1.8V_RUN_VPP_FUSE: disabling [ 3.832635] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.874371] EXT4-fs (mmcblk0p1): recovery complete [ 3.879975] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.888094] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.898218] devtmpfs: mounted [ 3.901843] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#