Pass: Linux Boot Test 1 Test Owner(s): N/A Execution Time 56.35 sec Percent passed so far: 50.0 Pass: Linux Boot Test 2 Test Owner(s): N/A Execution Time 55.91 sec Percent passed so far: 100.0 Final Score: 100.0 ¸[0024.380] Enabled early print [0024.382] [TegraBoot] (version 24.00.2015.42-mobile-46960d1c) [0024.388] Processing in recovery mode [0024.391] A02 Bootrom Patch rev = 63 [0024.395] Power-up reason: pmc por [0024.398] Established communication link with host [0025.362] Odmdata from BCT: 0x00084000 [0025.366] DebugPort= 0x3 [0025.368] BoardId read from EEPROM/NCT: 2180 [0025.396] Turned on fan for loki board [0025.400] Key release before reqd. time for fastboot [0025.405] No Battery Present [0025.407] RamCode = 0 [0025.410] Platform has Ddr4 type ram [0025.413] max77620 disabling SD1 Remote Sense [0025.417] Setting Ddr voltage to 1125mv [0025.421] Serial Number of Pmic Max77663: 0x807a4 [0025.429] Entering ramdump check [0025.432] Get RamDumpCarveOut = 0x0 [0025.435] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0025.440] Last reboot was clean, booting normally! [0025.445] Sdram initialization is successful [0025.449] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0025.454] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0025.460] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0025.465] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0025.470] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0025.475] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0025.480] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0025.485] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0025.501] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0025.506] Platform-DebugCarveout: 0 [0025.510] Downloaded Bct successfully [0025.604] Downloaded bootloader successfully at 0x92c00000 [0025.697] Downloaded rp1 successfully at 0x83000000 [0025.736] MAX77620_GPIO1 Configured. [0025.739] MAX77620_GPIO5 Configured. [0025.743] CPU power rail is up [0025.746] CPU clock enabled [0025.750] Performing RAM repair [0025.752] Updating A64 Warmreset Address to 0x92c002e9 [0025.759] Enable APE clock/reset [0025.762] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0025.766] Loading Secure OS image failed. [0025.770] Set NvDecSticky Bits [0025.774] GSC1 address : ff700000 [0025.777] GSC2 address ff63fffc value c0edbbcc [0025.782] GSC2 address : ff600000 [0025.786] GSC3 address : ff500000 [0025.789] GSC4 address : ff400000 [0025.793] GSC5 address : ff300000 [0025.796] GSC MC Settings done [0025.799] NvTbootPackSdramParams: start. [0025.804] NvTbootPackSdramParams: done. [0025.808] Next binary entry address: 0x92c00258 [0025.812] BoardId: 2180 [0025.815] dram memory type is 3 [0025.818] Tegraboot started after 24965132 us [0025.823] Basic modules init took -24965132 us [0025.827] USB data transfer took 0 us [0025.830] Carveout took 26434830 us [0025.834] CPU initialization took 3629 us [0025.837] Total time taken by TegraBoot 1473327 us [0025.842] Starting CPU & Halting co-processor [0026.472] [0026.473] Debug Init done [0026.475] Marked DTB cacheable [0026.478] Bootloader DTB loaded at 0x83000000 [0026.483] DeviceTree Init done [0026.497] Pinmux applied successfully [0026.502] gicd_base: 0x50041000 [0026.506] gicc_base: 0x50042000 [0026.509] Interrupts Init done [0026.513] Using base:0x60005008 & irq:33 for tick-timer [0026.518] Using base:0x60005000 for delay-timer [0026.523] platform_init_timer: DONE [0026.526] Timer(tick) Init done [0026.530] osc freq = 38400 khz [0026.535] [0026.536] welcome to cboot [0026.539] [0026.540] Cboot Version: 24.00.2015.42-t210-63d15635 [0026.545] calling constructors [0026.548] initializing heap [0026.550] initializing threads [0026.553] initializing timers [0026.556] creating bootstrap completion thread [0026.561] top of bootstrap2() [0026.563] CPU: ARM Cortex A57 [0026.566] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0026.571] initializing platform [0026.597] config for ddr50 mode completed [0026.601] sdmmc bdev is already initialized [0026.605] of_register: registering tegra_udc to of_hal [0026.610] of_register: registering inv20628-driver to of_hal [0026.616] of_register: registering ads1015-driver to of_hal [0026.622] of_register: registering lp8557-bl-driver to of_hal [0026.627] of_register: registering bq2419x_charger to of_hal [0026.633] of_register: registering cpc to of_hal [0026.638] of_register: registering bq27441_fuel_gauge to of_hal [0026.652] gpio framework initialized [0026.655] of_register: registering tca9539_gpio to of_hal [0026.661] of_register: registering tca9539_gpio to of_hal [0026.666] of_register: registering i2c_bus_driver to of_hal [0026.672] of_register: registering i2c_bus_driver to of_hal [0026.677] of_register: registering i2c_bus_driver to of_hal [0026.683] pmic framework initialized [0026.686] of_register: registering max77620_pmic to of_hal [0026.692] regulator framework initialized [0026.696] of_register: registering tps65132_bl_driver to of_hal [0026.702] of_register: registering tegra_xhci to of_hal [0026.707] initializing target [0026.713] gpio_driver_register: register 'tegra_gpio_driver' driver [0026.723] fixed regulator driver initialized [0026.788] initializing OF layer [0026.792] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0026.800] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.822] I2C Bus Init done [0026.825] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.837] I2C Bus Init done [0026.840] of_children_init: Ops found for compatible string ti,lp8557 [0026.846] I2C slave not started [0026.849] I2C write failed [0026.852] Writing offset failed [0026.855] failed to read 0x 0 [0026.858] lp8557: Couldn't turn off backlight: -3 [0026.862] lp8557: device config err: -3of_children_init: Ops found for compatible string ti,tca9539 [0026.876] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0026.882] gpio_driver_register: register 'tca9539_gpio_driver' driver [0026.888] of_children_init: Ops found for compatible string ti,tca9539 [0026.899] tca9539_init: i2c bus: 2, slave addr: 0xee [0026.905] gpio_driver_register: register 'tca9539_gpio_driver' driver [0026.911] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.923] I2C Bus Init done [0026.926] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.938] I2C Bus Init done [0026.940] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.952] I2C Bus Init done [0026.955] of_children_init: Ops found for compatible string maxim,max77620 [0026.967] max77620_init using irq 118 [0026.972] register 'maxim,max77620' pmic [0026.977] gpio_driver_register: register 'max77620-gpio' driver [0026.983] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0026.995] I2C Bus Init done [0026.998] of_children_init: Ops found for compatible string nvidia,tegra210-udc [0027.006] calling apps_init() [0027.012] Found 19 GPT partitions in "sdmmc3_user" [0027.016] Proceeding to flashing Server [0027.020] usbdcd_reinit Initialize driver to use already enumerated device [0027.027] nv3p_priv_usbf_open USB configuration success [0027.034] Writing GPT partition [0027.038] Erasing Boot device [0027.064] Erasing Storage Device [0027.313] Sanitizing Storage Device [0027.428] Writing protective mbr [0027.432] Writing primary GPT [0027.438] Writing secondary GPT [0027.443] Found 18 GPT partitions in "sdmmc3_user" [0027.449] Writing NVC partition [0027.452] bct_init bctinit [0027.455] bct_init bctinit [0027.463] bct_init bctinit [0027.465] bct_init bctinit [0027.468] bct_init bctinit [0027.501] partition NVC write successful. [0027.506] Writing APP partition [0027.509] bct_init bctinit [0028.326] bct_init bctinit [0028.328] bct_init bctinit [0028.934] partition APP write successful. [0028.939] Writing TBC partition [0028.942] bct_init bctinit [0028.947] bct_init bctinit [0028.950] bct_init bctinit [0028.955] partition TBC write successful. [0028.960] Writing EBT partition [0028.963] bct_init bctinit [0028.982] bct_init bctinit [0028.984] bct_init bctinit [0028.997] partition EBT write successful. [0029.002] Writing BPF partition [0029.005] bct_init bctinit [0029.023] bct_init bctinit [0029.025] bct_init bctinit [0029.031] partition BPF write successful. [0029.035] Writing WB0 partition [0029.038] bct_init bctinit [0029.042] bct_init bctinit [0029.044] bct_init bctinit [0029.049] partition WB0 write successful. [0029.053] Writing RP1 partition [0029.056] bct_init bctinit [0029.072] bct_init bctinit [0029.074] bct_init bctinit [0029.084] partition RP1 write successful. [0029.088] Writing TOS partition [0029.091] bct_init bctinit [0029.097] bct_init bctinit [0029.099] bct_init bctinit [0029.105] partition TOS write successful. [0029.110] Writing DTB partition [0029.113] bct_init bctinit [0029.128] bct_init bctinit [0029.131] bct_init bctinit [0029.140] partition DTB write successful. [0029.148] Writing BCT partition [0029.152] bct_init bctinit [0029.249] partition BCT write successful. [0029.257] Change state to cold boot mode [0029.261] Flushing data to stroage [0000.153] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.158] Processing in cold boot mode Bootloader 2 [0000.163] A02 Bootrom Patch rev = 63 [0000.166] Power-up reason: software reset [0000.170] No Battery Present [0000.173] RamCode = 0 [0000.175] Platform has Ddr4 type ram [0000.178] max77620 disabling SD1 Remote Sense [0000.183] Setting Ddr voltage to 1125mv [0000.186] Serial Number of Pmic Max77663: 0x807a4 [0000.194] Entering ramdump check [0000.197] Get RamDumpCarveOut = 0x0 [0000.200] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.205] Last reboot was clean, booting normally! [0000.210] Sdram initialization is successful [0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.271] Platform-DebugCarveout: 0 [0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.280] Non secure mode. Disable rollback prevention [0000.285] AOTAG Init Done [0000.312] Using GPT Primary to query partitions [0000.317] Loading Tboot-CPU binary [0000.366] Verifying bootloader in OdmNonSecureSBK mode [0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.383] Bootloader downloaded successfully. [0000.387] Downloaded Tboot-CPU binary to 0xa0000258 [0000.392] MAX77620_GPIO1 Configured. [0000.396] MAX77620_GPIO5 Configured. [0000.399] CPU power rail is up [0000.402] CPU clock enabled [0000.406] Performing RAM repair [0000.409] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Bootloader DTB Load Address: 0x83000000 [0000.442] Kernel DTB Load Address: 0x83080000 [0000.447] Loading cboot binary [0000.541] Verifying bootloader in OdmNonSecureSBK mode [0000.647] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.654] Bootloader downloaded successfully. [0000.658] GPT: Partition NOT found ! [0000.661] Find Partition via GPT Failed [0000.665] Find Partition via PT Failed [0000.669] function NvTbootGetBinaryOffsets: 0x1 error [0000.673] Error in NvTbootLoadBinary: 0x1 ! [0000.677] Next binary entry address: 0x80110000 [0000.682] BoardId: 2180 [0000.687] dram memory type is 3 [0000.691] WB0 init successful [0000.717] Bpmp FW successfully loaded [0000.720] Set NvDecSticky Bits [0000.723] GSC1 address : ff700000 [0000.727] GSC2 address ff63fffc value c0edbbcc [0000.732] GSC2 address : ff600000 [0000.735] GSC3 address : ff500000 [0000.739] GSC4 address : ff400000 [0000.743] GSC5 address : ff300000 [0000.746] GSC MC Settings done [0000.749] TOS old plaintext Image length 65536 [0000.756] *** Secure OS image signature not verified *** [0000.761] Loading and Validation of Secure OS Successful [0000.766] NvTbootPackSdramParams: start. [0000.771] NvTbootPackSdramParams: done. [0000.775] Tegraboot started after 132069 us [0000.779] Basic modules init took 292353 us [0000.783] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.788] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.796] Next stage binary read took 12205 us [0000.800] Carveout took 264379 us [0000.803] CPU initialization took 92728 us [0000.807] Total time taken by TegraBoot 661665 us [0000.812] Starting CPU & Halting co-processor 64b[0000.919] RamCode = 0 [0000.934] LPDDR4 Training: Read DT: Number of tables = 10 [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.944] EMC Training Skipped [0000.947] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.952] EMC Training Skipped [0000.955] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.960] EMC Training Skipped [0000.963] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.969] EMC Training Skipped [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.978] EMC Training Successful [0000.981] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.986] EMC Training Successful [0000.989] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.001] EMC Training Successful [0001.004] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.027] EMC Training Successful [0001.030] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.051] EMC Training Successful [0001.054] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.074] EMC Training Successful [0001.077] Switching to 800000 KHz Success [0001.083] DT Write: emc-table@40800 succeeded [0001.089] DT Write: emc-table@68000 succeeded [0001.096] DT Write: emc-table@102000 succeeded [0001.102] DT Write: emc-table@204000 succeeded [0001.109] DT Write: emc-table@408000 succeeded [0001.115] DT Write: emc-table@665600 succeeded [0001.121] DT Write: emc-table@800000 succeeded [0001.128] DT Write: emc-table@1065600 succeeded [0001.134] DT Write: emc-table@1331200 succeeded [0001.140] DT Write: emc-table@1600000 succeeded [0001.145] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1 €0ÜŒù[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x807a4 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.373] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.687] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.706] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.713] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.738] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99025 us [0000.746] Basic modules init took 292133 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12205 us [0000.767] Carveout took 264374 us [0000.771] CPU initialization took 92727 us [0000.774] Total time taken by TegraBoot 661439 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.044] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.082] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.101] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915493 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17115648 bytes read in 435 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11021/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 53 ms (967.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.456219] console [ttyS0] enabled [ 0.456219] console [ttyS0] enabled [ 0.463730] bootconsole [uart0] disabled [ 0.463730] bootconsole [uart0] disabled [ 0.472580] SuperH (H)SCI(F) driver initialized [ 0.477787] msm_serial: driver initialized [ 0.482625] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.493294] loop: module loaded [ 0.498555] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.510356] max77620-sd0: supplied by regulator-dummy [ 0.516710] max77620-sd1: supplied by regulator-dummy [ 0.522867] max77620-sd2: supplied by regulator-dummy [ 0.528818] max77620-sd3: supplied by regulator-dummy [ 0.535245] max77620-ldo0: supplied by regulator-dummy [ 0.541329] max77620-ldo1: supplied by regulator-dummy [ 0.547102] max77620-ldo2: supplied by regulator-dummy [ 0.553136] max77620-ldo3: supplied by regulator-dummy [ 0.558309] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.565216] max77620-ldo4: supplied by regulator-dummy [ 0.570390] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.576986] max77620-ldo5: supplied by regulator-dummy [ 0.582171] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.589176] max77620-ldo6: supplied by regulator-dummy [ 0.594347] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.601262] max77620-ldo7: supplied by regulator-dummy [ 0.607264] max77620-ldo8: supplied by regulator-dummy [ 0.621163] libphy: Fixed MDIO Bus: probed [ 0.626281] tun: Universal TUN/TAP device driver, 1.6 [ 0.632643] thunder-xcv, ver 1.0 [ 0.636215] thunder-BGX, ver 1.0 [ 0.639614] thunder-nic, ver 1.0 [ 0.643271] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.649240] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.655225] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.662226] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.667881] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.675745] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.682016] sky2: driver version 1.30 [ 0.686215] usbcore: registered new interface driver r8152 [ 0.692004] VFIO - User Level meta-driver version: 0.3 [ 0.702324] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.709210] ehci-pci: EHCI PCI platform driver [ 0.713718] ehci-platform: EHCI generic platform driver [ 0.719100] ehci-orion: EHCI orion driver [ 0.723291] ehci-exynos: EHCI EXYNOS driver [ 0.727617] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.733844] ohci-pci: OHCI PCI platform driver [ 0.738349] ohci-platform: OHCI generic platform driver [ 0.743715] ohci-exynos: OHCI EXYNOS driver [ 0.748739] usbcore: registered new interface driver usb-storage [ 0.889081] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.897624] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.905032] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.911429] i2c /dev entries driver [ 0.920310] sdhci: Secure Digital Host Controller Interface driver [ 0.926570] sdhci: Copyright(c) Pierre Ossman [ 0.931336] Synopsys Designware Multimedia Card Interface Driver [ 0.938291] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.944487] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.965536] mmc0: Unknown controller version (3). You may experience problems. [ 1.002087] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.011411] ledtrig-cpu: registered to indicate activity on CPUs [ 1.019141] usbcore: registered new interface driver usbhid [ 1.025622] usbhid: USB HID core driver [ 1.031883] NET: Registered protocol family 17 [ 1.037332] 9pnet: Installing 9P2000 support [ 1.041709] Key type dns_resolver registered [ 1.046656] registered taskstats version 1 [ 1.050953] Loading compiled-in X.509 certificates [ 1.062587] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.067644] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.073585] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.079012] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.085095] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.091904] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.097413] mmc0: new high speed MMC card at address 0001 [ 1.102894] RTL_5V: supplied by VDD_5V0_SYS [ 1.103209] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.113222] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.117839] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.118102] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.119497] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.119700] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.119768] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.119818] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.144315] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.170922] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.177528] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.177966] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.178121] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.198163] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.211427] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.619567] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.028627] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.437688] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.445179] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.450674] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.458867] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.867895] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.276957] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.686010] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.693502] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.699109] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.705415] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.711605] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.718486] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.725806] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.731785] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.739861] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.749213] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.818144] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.825549] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.830958] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.839545] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.848185] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.854679] hub 1-0:1.0: USB hub found [ 3.858543] hub 1-0:1.0: 5 ports detected [ 3.862955] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.868438] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.876091] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.884549] hub 2-0:1.0: USB hub found [ 3.888390] hub 2-0:1.0: 4 ports detected [ 3.893771] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.905647] mmc1: Unknown controller version (3). You may experience problems. [ 3.942160] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.950317] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.962463] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.970207] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.977786] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.990258] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.022020] max77686-rtc max77620-rtc: setting system clock to 2017-12-06 16:44:26 UTC (1512578666) [ 4.226004] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.252811] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.265730] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.390393] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.450710] r8152 2-1:1.0 eth0: v1.09.9 [ 4.454787] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.466891] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.356076] r8152 2-1:1.0 eth0: carrier on [ 7.385501] IP-Config: Complete: [ 7.388749] device=eth0, hwaddr=00:04:4b:79:95:86, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.398914] host=192.168.99.2, domain=, nis-domain=(none) [ 7.404742] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.412168] AVDD_DSI_CSI_1V2: disabling [ 7.416025] VDD_PRE_REG_1V35: disabling [ 7.419901] VDD_CAM_HV: disabling [ 7.423358] VDD_TS_HV: disabling [ 7.426705] VDD_TS_1V8: disabling [ 7.430022] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.434376] VDD_3V3_SD: disabling [ 7.437690] VDD_HDMI_5V0: disabling [ 7.441169] ALSA device list: [ 7.444135] No soundcards found. [ 7.448230] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 16:44:29 ] L4T-INITRD Build DATE: Wed Dec 6 16:44:29 UTC 2017 [ 16:44:29 ] Root device found: nfs [ 16:44:29 ] Ethernet interfaces: eth0 [ 16:44:29 ] IP Address: 192.168.99.2 [ 16:44:29 ] Rootfs mounted over nfs [ 16:44:29 ] Switching from initrd to actual rootfs [ 7.993351] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 8.011726] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 8.048826] systemd[1]: Set hostname to . [ 8.492914] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.513835] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.533660] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.549600] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.565634] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.581630] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.597638] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on udev Kernel Socket. [ OK ] Created slice System Slice. [ OK ] Reached target Slices. Mounting Debug File System... Mounting Huge Pages File System... [ OK ] Created slice system-getty.slice. Mounting POSIX Message Queue File System... [ OK ] Created slice system-serial\x2dgetty.slice. Starting Remount Root and Kernel File Systems... Starting Load Kernel Modules... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on Journal Audit Socket. Starting Journal Service... Starting Create Static Device Nodes in /dev... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. Mounting RPC Pipe File System... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Set console keymap... [ OK ] Mounted Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [ OK ] Started Preprocess NFS configuration. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started udev Kernel Device Manager. [ 9.405082] systemd-journald[1516]: Received request to flush runtime journal from PID 1 [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting OpenBSD Secure Shell server... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting /etc/rc.local Compatibility... Starting System Logging Service... Starting Permit User Sessions... Starting Login Service... Starting LSB: Start NTP daemon... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Regular background program processing daemon. [ OK ] Started System Logging S[ 10.896526] random: crng init done ervice. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/ttyS0. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login:  f…ò[0000.121] [TegraBoot] (version 24.00.2015.42-mobile-ec3b827e) [0000.126] Processing in cold boot mode Bootloader 2 [0000.131] A02 Bootrom Patch rev = 63 [0000.134] Power-up reason: reset button [0000.138] No Battery Present [0000.140] RamCode = 0 [0000.143] Platform has Ddr4 type ram [0000.146] max77620 disabling SD1 Remote Sense [0000.150] Setting Ddr voltage to 1125mv [0000.154] Serial Number of Pmic Max77663: 0x807a4 [0000.162] Entering ramdump check [0000.165] Get RamDumpCarveOut = 0x0 [0000.168] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.173] Last reboot was clean, booting normally! [0000.178] Sdram initialization is successful [0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.197] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.233] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.239] Platform-DebugCarveout: 0 [0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.247] Non secure mode. Disable rollback prevention [0000.252] AOTAG Init Done [0000.280] Using GPT Primary to query partitions [0000.285] Loading Tboot-CPU binary [0000.334] Verifying bootloader in OdmNonSecureSBK mode [0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.351] Bootloader downloaded successfully. [0000.355] Downloaded Tboot-CPU binary to 0xa0000258 [0000.360] MAX77620_GPIO1 Configured. [0000.363] MAX77620_GPIO5 Configured. [0000.367] CPU power rail is up [0000.370] CPU clock enabled [0000.373] Performing RAM repair [0000.376] Updating A64 Warmreset Address to 0xa00002e9 [0000.393] Bootloader DTB Load Address: 0x83000000 [0000.410] Kernel DTB Load Address: 0x83080000 [0000.415] Loading cboot binary [0000.509] Verifying bootloader in OdmNonSecureSBK mode [0000.614] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0000.621] Bootloader downloaded successfully. [0000.626] GPT: Partition NOT found ! [0000.629] Find Partition via GPT Failed [0000.633] Find Partition via PT Failed [0000.636] function NvTbootGetBinaryOffsets: 0x1 error [0000.641] Error in NvTbootLoadBinary: 0x1 ! [0000.645] Next binary entry address: 0x80110000 [0000.649] BoardId: 2180 [0000.654] dram memory type is 3 [0000.658] WB0 init successful [0000.684] Bpmp FW successfully loaded [0000.687] Set NvDecSticky Bits [0000.691] GSC1 address : ff700000 [0000.694] GSC2 address ff63fffc value c0edbbcc [0000.699] GSC2 address : ff600000 [0000.703] GSC3 address : ff500000 [0000.706] GSC4 address : ff400000 [0000.710] GSC5 address : ff300000 [0000.713] GSC MC Settings done [0000.717] TOS old plaintext Image length 65536 [0000.723] *** Secure OS image signature not verified *** [0000.728] Loading and Validation of Secure OS Successful [0000.733] NvTbootPackSdramParams: start. [0000.738] NvTbootPackSdramParams: done. [0000.742] Tegraboot started after 99029 us [0000.746] Basic modules init took 292130 us [0000.750] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB [0000.756] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB [0000.763] Next stage binary read took 12205 us [0000.767] Carveout took 264373 us [0000.771] CPU initialization took 92728 us [0000.774] Total time taken by TegraBoot 661436 us [0000.779] Starting CPU & Halting co-processor 64b[0000.887] RamCode = 0 [0000.902] LPDDR4 Training: Read DT: Number of tables = 10 [0000.907] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.912] EMC Training Skipped [0000.915] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.920] EMC Training Skipped [0000.923] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.928] EMC Training Skipped [0000.931] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0000.936] EMC Training Skipped [0000.939] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0000.945] EMC Training Successful [0000.948] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0000.954] EMC Training Successful [0000.957] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0000.968] EMC Training Successful [0000.971] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0000.994] EMC Training Successful [0000.997] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.019] EMC Training Successful [0001.022] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.041] EMC Training Successful [0001.044] Switching to 800000 KHz Success [0001.051] DT Write: emc-table@40800 succeeded [0001.057] DT Write: emc-table@68000 succeeded [0001.063] DT Write: emc-table@102000 succeeded [0001.070] DT Write: emc-table@204000 succeeded [0001.076] DT Write: emc-table@408000 succeeded [0001.082] DT Write: emc-table@665600 succeeded [0001.089] DT Write: emc-table@800000 succeeded [0001.095] DT Write: emc-table@1065600 succeeded [0001.101] DT Write: emc-table@1331200 succeeded [0001.108] DT Write: emc-table@1600000 succeeded [0001.112] LPDDR4 Training: Write DT: Number of tables = 10 U-Boot 2017.03-g8537ddd769f4 (Oct 04 2017 - 08:47:08 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 3.5 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 MMC: no card present mmc_init: -123, time 1 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 432 bytes read in 69 ms (5.9 KiB/s) p2371-2180 NFS boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 6915493 bytes read in 217 ms (30.4 MiB/s) Retrieving file: /boot/Image 17115648 bytes read in 435 ms (37.5 MiB/s) append: console=ttyS0,115200n8 earlycon ignore_loglevel root=/dev/nfs rw netdevwait ip=192.168.99.2:192.168.99.1:192.168.99.1:255.255.255.0::eth0:off nfsroot=192.168.99.1:/home/ausvrl11021/nfsroot,nolock,nfsvers=2 rootwait Retrieving file: /boot/tegra210-p2371-2180.dtb 52560 bytes read in 53 ms (967.8 KiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200fd4f Starting kernel ... [ 0.456565] console [ttyS0] enabled [ 0.456565] console [ttyS0] enabled [ 0.464076] bootconsole [uart0] disabled [ 0.464076] bootconsole [uart0] disabled [ 0.472945] SuperH (H)SCI(F) driver initialized [ 0.478172] msm_serial: driver initialized [ 0.483013] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.493680] loop: module loaded [ 0.498913] max77620 1-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.510705] max77620-sd0: supplied by regulator-dummy [ 0.517095] max77620-sd1: supplied by regulator-dummy [ 0.523267] max77620-sd2: supplied by regulator-dummy [ 0.529193] max77620-sd3: supplied by regulator-dummy [ 0.535616] max77620-ldo0: supplied by regulator-dummy [ 0.541709] max77620-ldo1: supplied by regulator-dummy [ 0.547480] max77620-ldo2: supplied by regulator-dummy [ 0.553512] max77620-ldo3: supplied by regulator-dummy [ 0.558687] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV [ 0.565595] max77620-ldo4: supplied by regulator-dummy [ 0.570767] VDD_RTC: Bringing 1000000uV into 850000-850000uV [ 0.577354] max77620-ldo5: supplied by regulator-dummy [ 0.582538] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV [ 0.589549] max77620-ldo6: supplied by regulator-dummy [ 0.594724] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV [ 0.601636] max77620-ldo7: supplied by regulator-dummy [ 0.607638] max77620-ldo8: supplied by regulator-dummy [ 0.621537] libphy: Fixed MDIO Bus: probed [ 0.626659] tun: Universal TUN/TAP device driver, 1.6 [ 0.633026] thunder-xcv, ver 1.0 [ 0.636605] thunder-BGX, ver 1.0 [ 0.640008] thunder-nic, ver 1.0 [ 0.643672] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.649641] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.655628] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.662627] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.668285] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.676150] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.682428] sky2: driver version 1.30 [ 0.686634] usbcore: registered new interface driver r8152 [ 0.692425] VFIO - User Level meta-driver version: 0.3 [ 0.702729] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.709620] ehci-pci: EHCI PCI platform driver [ 0.714128] ehci-platform: EHCI generic platform driver [ 0.719513] ehci-orion: EHCI orion driver [ 0.723704] ehci-exynos: EHCI EXYNOS driver [ 0.728031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.734258] ohci-pci: OHCI PCI platform driver [ 0.738763] ohci-platform: OHCI generic platform driver [ 0.744131] ohci-exynos: OHCI EXYNOS driver [ 0.749162] usbcore: registered new interface driver usb-storage [ 0.889458] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 0.898001] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.905415] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.911812] i2c /dev entries driver [ 0.919738] sdhci: Secure Digital Host Controller Interface driver [ 0.926936] sdhci: Copyright(c) Pierre Ossman [ 0.931607] Synopsys Designware Multimedia Card Interface Driver [ 0.938628] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.944802] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 0.965794] mmc0: Unknown controller version (3). You may experience problems. [ 1.002344] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.011674] ledtrig-cpu: registered to indicate activity on CPUs [ 1.019436] usbcore: registered new interface driver usbhid [ 1.025929] usbhid: USB HID core driver [ 1.032239] NET: Registered protocol family 17 [ 1.037636] 9pnet: Installing 9P2000 support [ 1.042011] Key type dns_resolver registered [ 1.046885] registered taskstats version 1 [ 1.051269] Loading compiled-in X.509 certificates [ 1.062908] VDD_5V0_SYS: supplied by VDD_SYS_MUX [ 1.067963] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2 [ 1.073904] VDD_3V3_SYS: supplied by VDD_SYS_MUX [ 1.079337] VDD_3V3_SD: supplied by VDD_3V3_SYS [ 1.085410] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS [ 1.092217] VDD_LCD_1V8_DIS: supplied by VDD_1V8 [ 1.097730] mmc0: new high speed MMC card at address 0001 [ 1.103214] RTL_5V: supplied by VDD_5V0_SYS [ 1.103526] USB_VBUS_EN1: supplied by VDD_5V0_SYS [ 1.113540] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 1.118159] VDD_HDMI_5V0: supplied by VDD_5V0_SYS [ 1.118418] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 1.119816] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.120019] usb2-3: usb2-3 supply vbus not found, using dummy regulator [ 1.120085] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 1.120134] usb3-1: usb3-1 supply vbus not found, using dummy regulator [ 1.144651] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.171266] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.177872] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB [ 1.178304] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB [ 1.178460] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB, chardev (240:0) [ 1.198505] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.211736] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 1.619828] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.028880] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.437930] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.445421] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.450918] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.459111] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.868144] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.277199] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.686254] tegra-pcie 1003000.pcie: link 1 down, retrying [ 3.693750] tegra-pcie 1003000.pcie: link 1 down, ignoring [ 3.699357] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.705661] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.711850] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.718732] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.726051] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.732022] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.740095] tegra-xusb 70090000.usb: 70090000.usb supply dvdd-pex-pll not found, using dummy regulator [ 3.749449] tegra-xusb 70090000.usb: 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator [ 3.818402] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC [ 3.825806] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.831214] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1 [ 3.839802] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010 [ 3.848442] tegra-xusb 70090000.usb: irq 325, io mem 0x70090000 [ 3.854933] hub 1-0:1.0: USB hub found [ 3.858792] hub 1-0:1.0: 5 ports detected [ 3.863204] tegra-xusb 70090000.usb: xHCI Host Controller [ 3.868687] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2 [ 3.876341] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.884794] hub 2-0:1.0: USB hub found [ 3.888633] hub 2-0:1.0: 4 ports detected [ 3.894004] sdhci-tegra 700b0000.sdhci: Got CD GPIO [ 3.905902] mmc1: Unknown controller version (3). You may experience problems. [ 3.942418] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit [ 3.950577] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.962715] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 3.970460] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.978031] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 3.990492] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.022231] max77686-rtc max77620-rtc: setting system clock to 2017-12-06 16:45:28 UTC (1512578728) [ 4.226261] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.253065] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.265959] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 4.390651] usb 2-1: reset SuperSpeed USB device number 2 using tegra-xusb [ 4.450973] r8152 2-1:1.0 eth0: v1.09.9 [ 4.455050] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe [ 4.467161] pwm-regulator regulators:regulator@100: Failed to get PWM: -517 [ 7.324352] r8152 2-1:1.0 eth0: carrier on [ 7.349760] IP-Config: Complete: [ 7.352983] device=eth0, hwaddr=00:04:4b:79:95:86, ipaddr=192.168.99.2, mask=255.255.255.0, gw=192.168.99.1 [ 7.363167] host=192.168.99.2, domain=, nis-domain=(none) [ 7.368996] bootserver=192.168.99.1, rootserver=192.168.99.1, rootpath= [ 7.376422] AVDD_DSI_CSI_1V2: disabling [ 7.380277] VDD_PRE_REG_1V35: disabling [ 7.384127] VDD_CAM_HV: disabling [ 7.387607] VDD_TS_HV: disabling [ 7.390955] VDD_TS_1V8: disabling [ 7.394270] AVDD_SATA_HDMI_DP_1V05: disabling [ 7.398626] VDD_3V3_SD: disabling [ 7.401941] VDD_HDMI_5V0: disabling [ 7.405421] ALSA device list: [ 7.408386] No soundcards found. [ 7.412489] Freeing unused kernel memory: 1152K /init: line 58: chmod: command not found [ 16:45:31 ] L4T-INITRD Build DATE: Wed Dec 6 16:45:31 UTC 2017 [ 16:45:31 ] Root device found: nfs [ 16:45:31 ] Ethernet interfaces: eth0 [ 16:45:31 ] IP Address: 192.168.99.2 [ 16:45:31 ] Rootfs mounted over nfs [ 16:45:31 ] Switching from initrd to actual rootfs [ 7.658567] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 7.676931] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 16.04 LTS! [ 7.694653] systemd[1]: Set hostname to . [ 7.997615] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.013927] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.030079] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.049814] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.065995] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 8.082004] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.101806] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. Mounting RPC Pipe File System... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on Journal Socket (/dev/log). Mounting Huge Pages File System... [ OK ] Listening on udev Control Socket. [ OK ] Created slice system-getty.slice. Starting Load Kernel Modules... Mounting Debug File System... Starting Remount Root and Kernel File Systems... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. Starting Create Static Device Nodes in /dev... Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Audit Socket. Starting Journal Service... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Starting udev Coldplug all Devices... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Preprocess NFS configuration... Starting Apply Kernel Variables... Mounting Configuration File System... Starting Flush Journal to Persistent Storage... [ OK ] Started Load/Save Random Seed. [FAILED] Failed to start Set console keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Preprocess NFS configuration. [ OK ] Started Apply Kernel Variables. [ OK ] Mounted Configuration File System. [ OK ] Started udev Kernel Device Manager. [ 8.905443] systemd-journald[1520]: Received request to flush runtime journal from PID 1 Starting Raise network interfaces... [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. Starting Permit User Sessions... Starting OpenBSD Secure Shell server... [ OK ] Started D-Bus System Message Bus. Starting Login Service... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting /etc/rc.local Compatibility... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting LSB: Start NTP daemon... [ OK ] Started Permit User Sessions. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started System Logging Service. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Login Service. [ OK ] Started Getty on tty1. [ OK ] Found device /dev/ttyS0. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ 10.918675] random: crng init done Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: Â