[0000.771] [TegraBoot] (version 23.00.2015.14-mobile-1ef66670) [0000.776] Processing in cold boot mode Bootloader 2 [0000.781] A01Q Bootrom Patch rev = 3 [0000.784] Power-up reason: on button [0000.788] No Battery Present [0000.791] Platform has Ddr4 type ram [0000.794] max77620 disabling SD1 Remote Sense [0000.798] Setting Ddr voltage to 1125mv [0000.802] Serial Number of Pmic Max77663: 0x40daf [0000.810] Entering ramdump check [0000.813] Get RamDumpCarveOut = 0x0 [0000.816] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.821] Last reboot was clean, booting normally! [0000.826] Sdram initialization is successful [0000.830] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.836] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.862] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.889] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.894] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.899] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.904] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.909] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.925] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.930] Platform-DebugCarveout: 0 [0000.934] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.984] Using GPT Primary to query partitions [0000.990] Loading Tboot-CPU binary [0001.038] Verifying bootloader in OdmNonSecureSBK mode [0001.048] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.057] Bootloader downloaded successfully. [0001.061] Downloaded Tboot-CPU binary to 0xa0000258 [0001.067] MAX77620_GPIO1 Configured. [0001.071] MAX77620_GPIO5 Configured. [0001.074] CPU power rail is up [0001.077] CPU clock enabled [0001.081] Performing RAM repair [0001.084] Updating A64 Warmreset Address to 0xa00002e9 [0001.103] Bootloader DTB Load Address: 0x83000000 [0001.120] Kernel DTB Load Address: 0x83080000 [0001.125] Loading cboot binary [0001.219] Verifying bootloader in OdmNonSecureSBK mode [0001.307] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0001.316] Bootloader downloaded successfully. [0001.320] GPT: Partition NOT found ! [0001.323] Find Partition via GPT Failed [0001.327] function NvTbootGetBinaryOffsets: 0x845208 error [0001.332] Error in NvTbootLoadBinary: 0x845208 ! [0001.337] GPT: Partition NOT found ! [0001.340] No FB partition [0001.343] Next binary entry address: 0x80110000 [0001.347] BoardId: 2595 [0001.352] dram memory type is 3 [0001.358] WB0 init successful [0001.384] Bpmp FW successfully loaded [0001.388] Set NvDecSticky Bits [0001.391] GSC1 address : ff700000 [0001.395] GSC2 address : ff600000 [0001.399] GSC3 address : ff500000 [0001.402] GSC4 address : ff400000 [0001.406] GSC5 address : ff300000 [0001.409] GSC MC Settings done [0001.415] TOS old plaintext Image length 61440 [0001.421] *** Secure OS image signature not verified *** [0001.426] Loading and Validation of Secure OS Successful [0001.431] NvTbootPackSdramParams: start. [0001.436] NvTbootPackSdramParams: done. [0001.440] Tegraboot started after 764326 us [0001.444] Basic modules init took 351024 us [0001.448] Sec Bootdevice Read Time = 203 ms, Read Size = 8459 KB [0001.454] Next stage binary read took 14367 us [0001.458] Carveout took 252669 us [0001.461] CPU initialization took 92446 us [0001.465] Total time taken by TegraBoot 710506 us [0001.470] Starting CPU & Halting co-processor 64b[0001.605] LPDDR4 Training: Number of tables = 10 [0001.609] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.615] EMC Training Successful [0001.618] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.624] EMC Training Successful [0001.627] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.639] EMC Training Successful [0001.642] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.665] EMC Training Successful [0001.668] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.689] EMC Training Successful [0001.692] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.712] EMC Training Successful [0001.715] Switching to 800000 KHz Success [0001.748] LPDDR4 Training: Number of tables = 10 U-Boot 2015.07-rc2-g2ac3917 (Nov 09 2015 - 13:12:08 -0800) TEGRA210 Model: NVIDIA P2371-0000 DRAM: 3 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0x1d5a000 |/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\CTRL+C - Operation aborted Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # env set fdt_copy_node_names /cpus:/psci Tegra210 (P2371-0000) # setenv rootpart 1 Tegra210 (P2371-0000) # setenv devtype mmc Tegra210 (P2371-0000) # setenv devnum 0 Tegra210 (P2371-0000) # part uuid ${devtype} ${devnum}:${rootpart} uuid Tegra210 (P2371-0000) # setenv bootargs ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${kernel_addr_r} /boot/Image.defconfig 16984576 bytes read in 845 ms (19.2 MiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${fdt_addr_r} /boot/tegra210-p2371-0000.dtb 44764 bytes read in 453 ms (95.7 KiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${ramdisk_addr_r} /boot/tegra-ramdisk.img 1627787 bytes read in 495 ms (3.1 MiB/s) Tegra210 (P2371-0000) # ramdisk_size=${filesize} Tegra210 (P2371-0000) # booti ${kernel_addr_r} - ${fdt_addr_r} ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200dedb Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd071] [ 0.000000] Linux version 4.15.0-rc2-next-20171204-336733-g7cc61a0a562c (jonathanh@tamien) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09)) #1 SMP PREEMPT Wed Dec 6 08:20:32 PST 2017 [ 0.000000] Machine model: NVIDIA Tegra210 P2371 (P2530/P2595) reference design [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000fe000000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000013fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x13ffb7e00-0x13ffb98ff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ff1fffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000013fffffff] [ 0.000000] On node 0 totalpages: 782848 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 520704 pages, LIFO batch:31 [ 0.000000] Normal zone: 4096 pages used for memmap [ 0.000000] Normal zone: 262144 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 23 pages/cpu @ (ptrval) s55936 r8192 d30080 u94208 [ 0.000000] pcpu-alloc: s55936 r8192 d30080 u94208 alloc=23*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] CPU features: enabling workaround for ARM erratum 834220 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 770560 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash [ 0.000000] software IO TLB [mem 0xfa000000-0xfe000000] (64MB) mapped at [ (ptrval)- (ptrval)] [ 0.000000] Memory: 2982164K/3131392K available (9724K kernel code, 1162K rwdata, 4488K rodata, 1152K init, 395K bss, 132844K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB) [ 0.000000] .text : 0x (ptrval) - 0x (ptrval) ( 9728 KB) [ 0.000000] .rodata : 0x (ptrval) - 0x (ptrval) ( 4544 KB) [ 0.000000] .init : 0x (ptrval) - 0x (ptrval) ( 1152 KB) [ 0.000000] .data : 0x (ptrval) - 0x (ptrval) ( 1163 KB) [ 0.000000] .bss : 0x (ptrval) - 0x (ptrval) ( 396 KB) [ 0.000000] fixed : 0xffff7dfffe7fb000 - 0xffff7dfffec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum) [ 0.000000] 0xffff7e0000000000 - 0xffff7e0003000000 ( 48 MB actual) [ 0.000000] memory : 0xffff800000000000 - 0xffff8000c0000000 ( 3072 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] boot misc1 0x0: expected 0x20 [ 0.000000] (comparison mask = 0xffffff) [ 0.000000] PLL_X already enabled. Postponing set full defaults [ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.008432] Console: colour dummy device 80x25 [ 0.013079] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.023701] pid_max: default: 32768 minimum: 301 [ 0.028554] Security Framework initialized [ 0.034969] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.043526] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.050878] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.057834] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.081287] ASID allocator initialised with 65536 entries [ 0.086951] Hierarchical SRCU implementation. [ 0.100449] Speedo Revision 4 [ 0.103539] Tegra Revision: A01 SKU: 1 CPU Process: -22 SoC Process: -22 [ 0.111364] EFI services will not be available. [ 0.124075] smp: Bringing up secondary CPUs ... [ 0.156906] Detected PIPT I-cache on CPU1 [ 0.156950] CPU1: Booted secondary processor 0x0000000001 [0x411fd071] [ 0.184969] Detected PIPT I-cache on CPU2 [ 0.185002] CPU2: Booted secondary processor 0x0000000002 [0x411fd071] [ 0.213038] Detected PIPT I-cache on CPU3 [ 0.213071] CPU3: Booted secondary processor 0x0000000003 [0x411fd071] [ 0.213152] smp: Brought up 1 node, 4 CPUs [ 0.250075] SMP: Total of 4 processors activated. [ 0.254936] CPU features: detected feature: 32-bit EL0 Support [ 0.261302] CPU: All CPU(s) started at EL2 [ 0.265551] alternatives: patching kernel code [ 0.274533] devtmpfs: initialized [ 0.285539] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.295670] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.302617] pinctrl core: initialized pinctrl subsystem [ 0.309439] DMI not present or invalid. [ 0.313762] NET: Registered protocol family 16 [ 0.318696] audit: initializing netlink subsys (disabled) [ 0.324397] audit: type=2000 audit(0.268:1): state=initialized audit_enabled=0 res=1 [ 0.332427] cpuidle: using governor menu [ 0.337387] vdso: 2 pages (1 code @ 00000000cafad73a, 1 data @ 000000000880aa54) [ 0.345061] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.353041] DMA: preallocated 256 KiB pool for atomic allocations [ 0.361679] Serial: AMBA PL011 UART driver [ 0.389328] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.396663] cryptd: max_cpu_qlen set to 1000 [ 0.401957] ACPI: Interpreter disabled. [ 0.406727] vgaarb: loaded [ 0.409766] SCSI subsystem initialized [ 0.414388] libata version 3.00 loaded. [ 0.418622] usbcore: registered new interface driver usbfs [ 0.424382] usbcore: registered new interface driver hub [ 0.429950] usbcore: registered new device driver usb [ 0.436203] pps_core: LinuxPPS API ver. 1 registered [ 0.441353] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.450825] PTP clock support registered [ 0.455025] EDAC MC: Ver: 3.0.0 [ 0.458819] Advanced Linux Sound Architecture Driver Initialized. [ 0.465788] clocksource: Switched to clocksource arch_sys_counter [ 0.472309] VFS: Disk quotas dquot_6.6.0 [ 0.476440] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.483702] pnp: PnP ACPI: disabled [ 0.494066] NET: Registered protocol family 2 [ 0.499103] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes) [ 0.507285] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.515092] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.522205] TCP: Hash tables configured (established 32768 bind 32768) [ 0.529086] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.535369] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.542200] NET: Registered protocol family 1 [ 0.547023] RPC: Registered named UNIX socket transport module. [ 0.553162] RPC: Registered udp transport module. [ 0.558041] RPC: Registered tcp transport module. [ 0.562913] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.569586] PCI: CLS 0 bytes, default 128 [ 0.574359] kvm [1]: 8-bit VMID [ 0.577603] kvm [1]: IDMAP page: 809e8000 [ 0.581764] kvm [1]: HYP VA range: 800000000000:ffffffffffff [ 0.588578] kvm [1]: vgic-v2@50044000 [ 0.592477] kvm [1]: vgic interrupt IRQ1 [ 0.596558] kvm [1]: virtual timer IRQ4 [ 0.600631] kvm [1]: Hyp mode initialized successfully [ 0.608782] Initialise system trusted keyrings [ 0.613502] workingset: timestamp_bits=44 max_order=20 bucket_order=0 [ 0.627044] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.633717] NFS: Registering the id_resolver key type [ 0.638977] Key type id_resolver registered [ 0.643323] Key type id_legacy registered [ 0.647487] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.654580] 9p: Installing v9fs 9p2000 file system support [ 0.662834] Key type asymmetric registered [ 0.667089] Asymmetric key parser 'x509' registered [ 0.672299] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.679986] io scheduler noop registered [ 0.684256] io scheduler cfq registered (default) [ 0.689134] io scheduler mq-deadline registered [ 0.693832] io scheduler kyber registered [ 0.712123] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.721779] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.734888] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.743326] console [ttyS0] disabled [ 0.747091] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 313, base_baud = 25500000) is a Tegra [ 0.756396] console [ttyS0] enabled [ 0.756396] console [ttyS0] enabled [ 0.763490] bootconsole [uart8250] disabled [ 0.763490] bootconsole [uart8250] disabled [ 0.772513] SuperH (H)SCI(F) driver initialized [ 0.777320] msm_serial: driver initialized [ 0.782031] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.793909] loop: module loaded [ 0.800170] libphy: Fixed MDIO Bus: probed [ 0.804833] tun: Universal TUN/TAP device driver, 1.6 [ 0.810459] thunder-xcv, ver 1.0 [ 0.813727] thunder-BGX, ver 1.0 [ 0.817012] thunder-nic, ver 1.0 [ 0.820497] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.826335] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.832302] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.839265] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.844887] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.852715] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.858882] sky2: driver version 1.30 [ 0.862942] VFIO - User Level meta-driver version: 0.3 [ 0.868930] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.875466] ehci-pci: EHCI PCI platform driver [ 0.879952] ehci-platform: EHCI generic platform driver [ 0.885264] ehci-orion: EHCI orion driver [ 0.889354] ehci-exynos: EHCI EXYNOS driver [ 0.893611] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.899805] ohci-pci: OHCI PCI platform driver [ 0.904291] ohci-platform: OHCI generic platform driver [ 0.909626] ohci-exynos: OHCI EXYNOS driver [ 0.914174] usbcore: registered new interface driver usb-storage [ 0.922239] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 0.929420] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 0.935754] i2c /dev entries driver [ 0.941874] sdhci: Secure Digital Host Controller Interface driver [ 0.948060] sdhci: Copyright(c) Pierre Ossman [ 0.952584] Synopsys Designware Multimedia Card Interface Driver [ 0.959135] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.973173] mmc0: Unknown controller version (3). You may experience problems. [ 1.011572] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit [ 1.020492] ledtrig-cpu: registered to indicate activity on CPUs [ 1.027502] usbcore: registered new interface driver usbhid [ 1.033142] usbhid: USB HID core driver [ 1.038748] NET: Registered protocol family 17 [ 1.043304] 9pnet: Installing 9P2000 support [ 1.047672] Key type dns_resolver registered [ 1.052604] registered taskstats version 1 [ 1.056786] Loading compiled-in X.509 certificates [ 1.070982] hctosys: unable to open rtc device (rtc0) [ 1.076575] ALSA device list: [ 1.079555] No soundcards found. [ 1.083322] Waiting for root device PARTUUID=00000000-0001-0000-788f-a75600000000... [ 1.117011] mmc0: new high speed MMC card at address 0001 [ 1.123162] mmcblk0: mmc0:0001 SDW16G 14.7 GiB [ 1.128295] mmcblk0boot0: mmc0:0001 SDW16G partition 1 4.00 MiB [ 1.134801] mmcblk0boot1: mmc0:0001 SDW16G partition 2 4.00 MiB [ 1.140898] mmcblk0rpmb: mmc0:0001 SDW16G partition 3 4.00 MiB, chardev (240:0) [ 1.150842] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 1.175767] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 1.196604] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.204728] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 1.219807] devtmpfs: mounted [ 1.223492] Freeing unused kernel memory: 1152K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#