U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB C: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################ 3.7 MiB/s done Bytes transferred = 8102400 (7ba200 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7ba200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.15.0-rc1-next-20171201-335689-gfb20eb9d798d (jonathanh@tamien) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Tue Dec 5 13:11:32 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39232 r8192 d22208 u69632 [ 0.000000] pcpu-alloc: s39232 r8192 d22208 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1992440K/2096128K available (11264K kernel code, 1602K rwdata, 4304K rodata, 2048K init, 404K bss, 38152K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1603 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 405 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000029] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000045] Switching to timer-based delay loop, resolution 1000ns [ 0.005687] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005706] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005727] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005741] Switching to timer-based delay loop, resolution 83ns [ 0.006236] Console: colour dummy device 80x30 [ 0.006270] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.006288] pid_max: default: 32768 minimum: 301 [ 0.006404] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006420] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006918] CPU: Testing write buffer coherency: ok [ 0.007184] /cpus/cpu@0 missing clock-frequency property [ 0.007230] /cpus/cpu@1 missing clock-frequency property [ 0.007275] /cpus/cpu@2 missing clock-frequency property [ 0.007321] /cpus/cpu@3 missing clock-frequency property [ 0.007335] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007638] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.009660] Hierarchical SRCU implementation. [ 0.011614] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.012410] EFI services will not be available. [ 0.012575] smp: Bringing up secondary CPUs ... [ 0.013154] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.016209] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.026232] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035685] smp: Brought up 1 node, 4 CPUs [ 0.035707] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035716] CPU: All CPU(s) started in SVC mode. [ 0.037229] devtmpfs: initialized [ 0.050763] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.051145] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.051165] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052606] pinctrl core: initialized pinctrl subsystem [ 0.054144] DMI not present or invalid. [ 0.054390] NET: Registered protocol family 16 [ 0.056584] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058988] cpuidle: using governor menu [ 0.084101] No ATAGs? [ 0.084228] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.084245] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.091826] Serial: AMBA PL011 UART driver [ 0.093240] iommu: Adding device reg-dummy to group 0 [ 0.093281] iommu: Adding device 1003000.pcie to group 1 [ 0.093357] iommu: Adding device 50000000.host1x to group 2 [ 0.093427] iommu: Adding device 54200000.dc to group 3 [ 0.093495] iommu: Adding device 54240000.dc to group 4 [ 0.093526] iommu: Adding device 54280000.hdmi to group 5 [ 0.093594] iommu: Adding device 57000000.gpu to group 6 [ 0.093630] iommu: Adding device 60005000.timer to group 7 [ 0.093661] iommu: Adding device 60007000.flow-controller to group 8 [ 0.093697] iommu: Adding device 6000c800.actmon to group 9 [ 0.093728] iommu: Adding device 6000d000.gpio to group 10 [ 0.093759] iommu: Adding device 60020000.dma to group 11 [ 0.093788] iommu: Adding device 70000800.apbmisc to group 12 [ 0.093819] iommu: Adding device 70000868.pinmux to group 13 [ 0.093849] iommu: Adding device 70006000.serial to group 14 [ 0.093879] iommu: Adding device 70006040.serial to group 15 [ 0.093914] iommu: Adding device 70006300.serial to group 16 [ 0.093944] iommu: Adding device 7000c000.i2c to group 17 [ 0.093974] iommu: Adding device 7000c400.i2c to group 18 [ 0.094009] iommu: Adding device 7000c500.i2c to group 19 [ 0.094040] iommu: Adding device 7000c700.i2c to group 20 [ 0.094070] iommu: Adding device 7000d000.i2c to group 21 [ 0.094101] iommu: Adding device 7000d400.spi to group 22 [ 0.094131] iommu: Adding device 7000da00.spi to group 23 [ 0.094165] iommu: Adding device 7000e000.rtc to group 24 [ 0.094196] iommu: Adding device 7000e400.pmc to group 25 [ 0.094226] iommu: Adding device 7000f800.fuse to group 26 [ 0.094257] iommu: Adding device 70019000.memory-controller to group 27 [ 0.094286] iommu: Adding device 7001b000.emc to group 28 [ 0.094317] iommu: Adding device 70027000.sata to group 29 [ 0.094352] iommu: Adding device 70030000.hda to group 30 [ 0.094387] iommu: Adding device 70090000.usb to group 31 [ 0.094417] iommu: Adding device 7009f000.padctl to group 32 [ 0.094452] iommu: Adding device 700b0400.sdhci to group 33 [ 0.094483] iommu: Adding device 700b0600.sdhci to group 34 [ 0.094513] iommu: Adding device 70015000.cec to group 35 [ 0.094544] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.094575] iommu: Adding device 70110000.clock to group 37 [ 0.094605] iommu: Adding device 70300000.ahub to group 38 [ 0.094635] iommu: Adding device 7d000000.usb to group 39 [ 0.094666] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.094704] iommu: Adding device 7d004000.usb to group 41 [ 0.094734] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.094765] iommu: Adding device 7d008000.usb to group 43 [ 0.094795] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.094824] iommu: Adding device pmu to group 45 [ 0.094854] iommu: Adding device timer to group 46 [ 0.094884] iommu: Adding device clocks to group 47 [ 0.094915] iommu: Adding device gpio-keys to group 48 [ 0.094948] iommu: Adding device regulators to group 49 [ 0.094979] iommu: Adding device regulators:regulator@0 to group 50 [ 0.095014] iommu: Adding device regulators:regulator@1 to group 51 [ 0.095045] iommu: Adding device regulators:regulator@2 to group 52 [ 0.095076] iommu: Adding device regulators:regulator@3 to group 53 [ 0.095107] iommu: Adding device regulators:regulator@4 to group 54 [ 0.095137] iommu: Adding device regulators:regulator@7 to group 55 [ 0.095168] iommu: Adding device regulators:regulator@8 to group 56 [ 0.095199] iommu: Adding device regulators:regulator@10 to group 57 [ 0.095232] iommu: Adding device regulators:regulator@11 to group 58 [ 0.095263] iommu: Adding device regulators:regulator@12 to group 59 [ 0.095293] iommu: Adding device regulators:regulator@13 to group 60 [ 0.095324] iommu: Adding device regulators:regulator@14 to group 61 [ 0.095362] iommu: Adding device sound to group 62 [ 0.110376] AT91: Could not find identification node [ 0.110944] +5V_SYS: supplied by +VDD_MUX [ 0.111227] +3.3V_SYS: supplied by +VDD_MUX [ 0.111840] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.111855] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.111954] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.111968] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.112152] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.112166] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.112262] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.112275] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.112369] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.112382] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.112477] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.112489] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.115520] vgaarb: loaded [ 0.116276] SCSI subsystem initialized [ 0.116459] libata version 3.00 loaded. [ 0.116652] usbcore: registered new interface driver usbfs [ 0.116699] usbcore: registered new interface driver hub [ 0.116762] usbcore: registered new device driver usb [ 0.120290] pps_core: LinuxPPS API ver. 1 registered [ 0.120301] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.120323] PTP clock support registered [ 0.120513] EDAC MC: Ver: 3.0.0 [ 0.123369] clocksource: Switched to clocksource arch_sys_counter [ 0.172728] NET: Registered protocol family 2 [ 0.173231] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.173333] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.173549] TCP: Hash tables configured (established 8192 bind 8192) [ 0.173635] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.173679] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.173828] NET: Registered protocol family 1 [ 0.174170] RPC: Registered named UNIX socket transport module. [ 0.174181] RPC: Registered udp transport module. [ 0.174190] RPC: Registered tcp transport module. [ 0.174198] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.174211] PCI: CLS 0 bytes, default 64 [ 0.175707] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.176460] iommu: Adding device alarmtimer to group 63 [ 0.177258] Initialise system trusted keyrings [ 0.177386] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.183969] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.184535] NFS: Registering the id_resolver key type [ 0.184562] Key type id_resolver registered [ 0.184572] Key type id_legacy registered [ 0.184614] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.186144] Key type asymmetric registered [ 0.186155] Asymmetric key parser 'x509' registered [ 0.186211] bounce: pool size: 64 pages [ 0.186258] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.186269] io scheduler noop registered [ 0.186279] io scheduler deadline registered [ 0.186496] io scheduler cfq registered (default) [ 0.186507] io scheduler mq-deadline registered [ 0.186516] io scheduler kyber registered [ 0.190573] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.190682] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.191053] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.210388] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.210445] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.216937] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.223470] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.226886] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.272648] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.272747] iommu: Adding device serial8250 to group 64 [ 0.275256] console [ttyS0] disabled [ 0.275295] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.541165] console [ttyS0] enabled [ 1.545548] SuperH (H)SCI(F) driver initialized [ 1.551194] msm_serial: driver initialized [ 1.555504] STMicroelectronics ASC driver initialized [ 1.561232] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.570483] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.601745] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.618674] brd: module loaded [ 1.628020] loop: module loaded [ 1.632432] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.640769] as3722 4-0040: AS3722 with revision 0x1 found [ 1.648128] iommu: Adding device as3722-pinctrl to group 65 [ 1.655200] iommu: Adding device as3722-regulator to group 66 [ 1.663803] as3722-sd2: supplied by +5V_SYS [ 1.668377] as3722-sd3: supplied by +5V_SYS [ 1.672775] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.679191] as3722-sd4: supplied by +5V_SYS [ 1.683800] as3722-sd5: supplied by +5V_SYS [ 1.689758] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.695814] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.701986] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.707890] as3722-ldo3: supplied by +3.3V_SYS [ 1.712368] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.720137] as3722-ldo4: supplied by +3.3V_SYS [ 1.724822] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.731000] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.735863] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.742751] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.748426] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.754620] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.764557] iommu: Adding device as3722-rtc to group 67 [ 1.770105] iommu: Adding device as3722-adc to group 68 [ 1.775655] iommu: Adding device as3722-power-off to group 69 [ 1.781694] iommu: Adding device as3722-wdt to group 70 [ 1.788785] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.811207] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.818302] iommu: Adding device Fixed MDIO bus.0 to group 71 [ 1.824420] libphy: Fixed MDIO Bus: probed [ 1.829464] CAN device driver interface [ 1.834276] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.841354] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.847261] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.853217] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.860182] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.869854] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.877297] usbcore: registered new interface driver pegasus [ 1.882984] usbcore: registered new interface driver asix [ 1.888424] usbcore: registered new interface driver ax88179_178a [ 1.894553] usbcore: registered new interface driver cdc_ether [ 1.900417] usbcore: registered new interface driver smsc75xx [ 1.906218] usbcore: registered new interface driver smsc95xx [ 1.911982] usbcore: registered new interface driver net1080 [ 1.917677] usbcore: registered new interface driver cdc_subset [ 1.923633] usbcore: registered new interface driver zaurus [ 1.929241] usbcore: registered new interface driver cdc_ncm [ 1.935143] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.940735] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.948251] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.954787] ehci-pci: EHCI PCI platform driver [ 1.959257] ehci-platform: EHCI generic platform driver [ 1.964714] ehci-orion: EHCI orion driver [ 1.968881] SPEAr-ehci: EHCI SPEAr driver [ 1.973029] ehci-st: EHCI STMicroelectronics driver [ 1.978059] ehci-exynos: EHCI EXYNOS driver [ 1.982400] ehci-atmel: EHCI Atmel driver [ 1.986571] tegra-ehci: Tegra EHCI driver [ 1.993427] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.998839] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 2.006592] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 2.033423] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 2.039993] hub 1-0:1.0: USB hub found [ 2.043807] hub 1-0:1.0: 1 port detected [ 2.048292] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.054501] ohci-pci: OHCI PCI platform driver [ 2.058978] ohci-platform: OHCI generic platform driver [ 2.064416] SPEAr-ohci: OHCI SPEAr driver [ 2.068568] ohci-st: OHCI STMicroelectronics driver [ 2.073604] ohci-atmel: OHCI Atmel driver [ 2.078405] usbcore: registered new interface driver usb-storage [ 2.086217] iommu: Adding device ci_hdrc.0 to group 72 [ 2.098415] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 2.105309] as3722-rtc as3722-rtc: RTC interrupt 379 [ 2.113691] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 2.120855] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 2.127615] i2c /dev entries driver [ 2.138213] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 2.153531] iommu: Adding device cpufreq-tegra124 to group 73 [ 2.161722] sdhci: Secure Digital Host Controller Interface driver [ 2.167920] sdhci: Copyright(c) Pierre Ossman [ 2.174105] Synopsys Designware Multimedia Card Interface Driver [ 2.181674] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.188168] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.193056] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.214340] mmc0: Unknown controller version (3). You may experience problems. [ 2.221596] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.258581] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.268220] ledtrig-cpu: registered to indicate activity on CPUs [ 2.274525] usbcore: registered new interface driver usbhid [ 2.280090] usbhid: USB HID core driver [ 2.288190] NET: Registered protocol family 10 [ 2.293500] Segment Routing with IPv6 [ 2.297218] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.303668] NET: Registered protocol family 17 [ 2.308112] can: controller area network core (rev 20170425 abi 9) [ 2.314361] NET: Registered protocol family 29 [ 2.318800] can: raw protocol (rev 20170425) [ 2.323064] can: broadcast manager protocol (rev 20170425 t) [ 2.328739] can: netlink gateway (rev 20170425) max_hops=1 [ 2.334517] Key type dns_resolver registered [ 2.339295] ThumbEE CPU extension supported. [ 2.343594] Registering SWP/SWPB emulation handler [ 2.348970] Loading compiled-in X.509 certificates [ 2.366501] +3.3V_RUN: supplied by +3.3V_SYS [ 2.372497] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.377259] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.383415] +5V_USB_HS: supplied by +5V_SYS [ 2.389499] +3.3V_LP0: supplied by +3.3V_SYS [ 2.396097] +5V_HDMI_CON: supplied by +5V_SYS [ 2.400982] +5V_SATA: supplied by +5V_SYS [ 2.405784] +12V_SATA: supplied by +VDD_MUX [ 2.411339] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.418211] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.425194] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.433471] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.439124] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.449018] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.459741] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.470741] as3722-sd2: supplied by +5V_SYS [ 2.475304] as3722-sd3: supplied by +5V_SYS [ 2.479702] as3722-sd4: supplied by +5V_SYS [ 2.484248] as3722-sd5: supplied by +5V_SYS [ 2.490187] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.496053] as3722-ldo1: supplied by +3.3V_RUN [ 2.500822] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.506520] as3722-ldo3: supplied by +3.3V_SYS [ 2.511955] as3722-ldo4: supplied by +3.3V_SYS [ 2.516825] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.521756] as3722-ldo6: supplied by +3.3V_RUN [ 2.526509] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.531987] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.539113] as3722-ldo9: supplied by +5V_SYS [ 2.545095] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.551897] as3722-ldo10: supplied by +5V_SYS [ 2.557128] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.563814] as3722-ldo11: supplied by +3.3V_RUN [ 2.569302] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.578144] mmc0: new high speed MMC card at address 0001 [ 2.584192] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.589105] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.595506] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.601692] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (236:0) [ 2.610277] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.619404] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.629338] mmcblk0: p1 [ 2.633040] scsi host0: tegra-ahci [ 2.638479] scsi host1: tegra-ahci [ 2.642097] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.650139] ata2: DUMMY [ 2.656202] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.661617] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.669459] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 2.703495] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.710452] hub 2-0:1.0: USB hub found [ 2.714306] hub 2-0:1.0: 1 port detected [ 2.720795] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.725752] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.737661] mmc1: Unknown controller version (3). You may experience problems. [ 2.745016] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.783247] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.791467] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.798860] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.806604] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.832455] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.840801] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.855654] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.861923] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.868141] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.875058] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.882373] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.887938] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.894010] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.903714] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.913445] pci 0000:00:01.0: enabling Extended Tags [ 2.918423] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.928228] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.938040] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.944709] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.954735] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.960760] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.970449] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.980162] pci 0000:00:02.0: enabling Extended Tags [ 2.985183] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.987139] ata1: SATA link down (SStatus 0 SControl 300) [ 3.000374] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.010160] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.016789] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.026792] PCI: bus0: Fast back to back transfers disabled [ 3.032364] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.040386] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.048554] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.054636] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.061708] PCI: bus1: Fast back to back transfers disabled [ 3.067320] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.074110] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.080139] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.085765] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.092564] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.099955] PCI: bus2: Fast back to back transfers disabled [ 3.105546] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.112188] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.118992] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.125824] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.133581] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.139691] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.147054] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.152020] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.158830] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.166597] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.173930] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.180023] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.185004] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.191109] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.197931] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.205716] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.212812] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.219166] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.225087] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.232137] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.238456] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.244543] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.250129] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.256014] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.279319] mmc1: new high speed SDHC card at address aaaa [ 3.285473] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.295129] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0x0d308bf2, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.304750] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.317414] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.326418] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.333034] [drm] No driver support for vblank timestamp query. [ 3.342806] mmcblk1: p1 p2 p3 [ 3.464340] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.711599] Console: switching to colour frame buffer device 512x135 [ 3.810204] drm drm: fb0: frame buffer device [ 3.814747] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.822427] iommu: Adding device cpufreq-dt.0 to group 74 [ 3.828322] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.835666] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.844959] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.852251] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:04:50 UTC (946685090) [ 3.861235] +USB0_VBUS_SW: disabling [ 3.864856] +1.8V_RUN_CAM: disabling [ 3.868647] +2.8V_RUN_CAM: disabling [ 3.872375] +1.2V_RUN_CAM_FRONT: disabling [ 3.876713] +1.05V_RUN_CAM_REAR: disabling [ 3.880960] +3.3V_RUN_TOUCH: disabling [ 3.884927] +2.8V_RUN_CAM_AF: disabling [ 3.888958] +1.8V_RUN_VPP_FUSE: disabling [ 3.894106] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.944059] EXT4-fs (mmcblk0p1): recovery complete [ 3.949792] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.957930] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.968117] devtmpfs: mounted [ 3.971750] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#