U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.tegra_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.tegra_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################ 4 MiB/s done Bytes transferred = 6192624 (5e7df0 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x5e7df0 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.15.0-rc1-next-20171128-14923-g5bef298 (jonathanh@kaivo) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP PREEMPT Mon Nov 27 20:02:56 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0xfbc00000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @eef88000 s39296 r8192 d22144 u69632 [ 0.000000] pcpu-alloc: s39296 r8192 d22144 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1998492K/2096128K available (9216K kernel code, 778K rwdata, 2560K rodata, 1024K init, 299K bss, 32100K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0d00000 - 0xc0e00000 (1024 kB) [ 0.000000] .data : 0xc0e00000 - 0xc0ec2ba4 ( 779 kB) [ 0.000000] .bss : 0xc0ec2ba4 - 0xc0f0d7ec ( 300 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.007454] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.016982] Switching to timer-based delay loop, resolution 1000ns [ 0.024224] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.029206] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.039953] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.047921] Switching to timer-based delay loop, resolution 83ns [ 0.054398] Console: colour dummy device 80x30 [ 0.058338] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.068646] pid_max: default: 32768 minimum: 301 [ 0.073723] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.079832] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.087677] CPU: Testing write buffer coherency: ok [ 0.092001] /cpus/cpu@0 missing clock-frequency property [ 0.097006] /cpus/cpu@1 missing clock-frequency property [ 0.102314] /cpus/cpu@2 missing clock-frequency property [ 0.107578] /cpus/cpu@3 missing clock-frequency property [ 0.112850] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152965] Setting up static identity map for 0x80100000 - 0x801000a0 [ 0.157717] Hierarchical SRCU implementation. [ 0.173503] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.192987] smp: Bringing up secondary CPUs ... [ 0.243617] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.323728] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.403843] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.413421] smp: Brought up 1 node, 4 CPUs [ 0.432509] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.438677] CPU: All CPU(s) started in SVC mode. [ 0.445124] devtmpfs: initialized [ 0.465077] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.471199] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.480633] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.488141] pinctrl core: initialized pinctrl subsystem [ 0.493179] NET: Registered protocol family 16 [ 0.497886] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.504539] cpuidle: using governor menu [ 0.530349] No ATAGs? [ 0.530483] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.538842] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.546563] iommu: Adding device reg-dummy to group 0 [ 0.549768] iommu: Adding device 1003000.pcie to group 1 [ 0.555067] iommu: Adding device 50000000.host1x to group 2 [ 0.560623] iommu: Adding device 54200000.dc to group 3 [ 0.565805] iommu: Adding device 54240000.dc to group 4 [ 0.570992] iommu: Adding device 54280000.hdmi to group 5 [ 0.576378] iommu: Adding device 57000000.gpu to group 6 [ 0.581651] iommu: Adding device 60005000.timer to group 7 [ 0.587084] iommu: Adding device 60007000.flow-controller to group 8 [ 0.593431] iommu: Adding device 6000c800.actmon to group 9 [ 0.598958] iommu: Adding device 6000d000.gpio to group 10 [ 0.604435] iommu: Adding device 60020000.dma to group 11 [ 0.609806] iommu: Adding device 70000800.apbmisc to group 12 [ 0.615530] iommu: Adding device 70000868.pinmux to group 13 [ 0.621150] iommu: Adding device 70006000.serial to group 14 [ 0.626796] iommu: Adding device 70006040.serial to group 15 [ 0.632410] iommu: Adding device 70006300.serial to group 16 [ 0.638064] iommu: Adding device 7000c000.i2c to group 17 [ 0.643417] iommu: Adding device 7000c400.i2c to group 18 [ 0.648809] iommu: Adding device 7000c500.i2c to group 19 [ 0.654164] iommu: Adding device 7000c700.i2c to group 20 [ 0.659563] iommu: Adding device 7000d000.i2c to group 21 [ 0.664910] iommu: Adding device 7000d400.spi to group 22 [ 0.670309] iommu: Adding device 7000da00.spi to group 23 [ 0.675659] iommu: Adding device 7000e000.rtc to group 24 [ 0.681052] iommu: Adding device 7000e400.pmc to group 25 [ 0.686403] iommu: Adding device 7000f800.fuse to group 26 [ 0.691883] iommu: Adding device 70019000.memory-controller to group 27 [ 0.698451] iommu: Adding device 7001b000.emc to group 28 [ 0.703848] iommu: Adding device 70027000.sata to group 29 [ 0.709286] iommu: Adding device 70030000.hda to group 30 [ 0.714678] iommu: Adding device 70090000.usb to group 31 [ 0.720032] iommu: Adding device 7009f000.padctl to group 32 [ 0.725697] iommu: Adding device 700b0400.sdhci to group 33 [ 0.731210] iommu: Adding device 700b0600.sdhci to group 34 [ 0.736776] iommu: Adding device 70015000.cec to group 35 [ 0.742144] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.748480] iommu: Adding device 70110000.clock to group 37 [ 0.754004] iommu: Adding device 70300000.ahub to group 38 [ 0.759484] iommu: Adding device 7d000000.usb to group 39 [ 0.764837] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.770576] iommu: Adding device 7d004000.usb to group 41 [ 0.775931] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.781674] iommu: Adding device 7d008000.usb to group 43 [ 0.787030] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.792761] iommu: Adding device pmu to group 45 [ 0.797337] iommu: Adding device timer to group 46 [ 0.802105] iommu: Adding device clocks to group 47 [ 0.806974] iommu: Adding device gpio-keys to group 48 [ 0.812072] iommu: Adding device regulators to group 49 [ 0.817297] iommu: Adding device regulators:regulator@0 to group 50 [ 0.823511] iommu: Adding device regulators:regulator@1 to group 51 [ 0.829771] iommu: Adding device regulators:regulator@2 to group 52 [ 0.835991] iommu: Adding device regulators:regulator@3 to group 53 [ 0.842248] iommu: Adding device regulators:regulator@4 to group 54 [ 0.848477] iommu: Adding device regulators:regulator@7 to group 55 [ 0.854729] iommu: Adding device regulators:regulator@8 to group 56 [ 0.860958] iommu: Adding device regulators:regulator@10 to group 57 [ 0.867295] iommu: Adding device regulators:regulator@11 to group 58 [ 0.873604] iommu: Adding device regulators:regulator@12 to group 59 [ 0.879948] iommu: Adding device regulators:regulator@13 to group 60 [ 0.886258] iommu: Adding device regulators:regulator@14 to group 61 [ 0.892600] iommu: Adding device sound to group 62 [ 0.914297] +5V_SYS: supplied by +VDD_MUX [ 0.916788] +3.3V_SYS: supplied by +VDD_MUX [ 0.921342] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.926672] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.934791] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.940517] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.948748] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.955535] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.963735] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.969550] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.977774] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.983328] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.991553] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.997194] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 1.006639] vgaarb: loaded [ 1.008784] SCSI subsystem initialized [ 1.011973] libata version 3.00 loaded. [ 1.015865] usbcore: registered new interface driver usbfs [ 1.021091] usbcore: registered new interface driver hub [ 1.026397] usbcore: registered new device driver usb [ 1.034605] Linux video capture interface: v2.00 [ 1.037386] pps_core: LinuxPPS API ver. 1 registered [ 1.042287] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.051391] PTP clock support registered [ 1.056692] Advanced Linux Sound Architecture Driver Initialized. [ 1.061966] Bluetooth: Core ver 2.22 [ 1.064924] NET: Registered protocol family 31 [ 1.069320] Bluetooth: HCI device and connection manager initialized [ 1.075624] Bluetooth: HCI socket layer initialized [ 1.080497] Bluetooth: L2CAP socket layer initialized [ 1.085532] Bluetooth: SCO socket layer initialized [ 1.091007] clocksource: Switched to clocksource arch_sys_counter [ 1.187105] NET: Registered protocol family 2 [ 1.190555] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.196694] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.203183] TCP: Hash tables configured (established 8192 bind 8192) [ 1.209801] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.215265] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.221871] NET: Registered protocol family 1 [ 1.236578] RPC: Registered named UNIX socket transport module. [ 1.240584] RPC: Registered udp transport module. [ 1.245311] RPC: Registered tcp transport module. [ 1.249944] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.256826] iommu: Adding device regulatory.0 to group 63 [ 1.261983] PCI: CLS 0 bytes, default 64 [ 1.267470] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 1.274486] iommu: Adding device alarmtimer to group 64 [ 1.280115] Initialise system trusted keyrings [ 1.283609] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 1.291226] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.306402] NFS: Registering the id_resolver key type [ 1.309557] Key type id_resolver registered [ 1.313758] Key type id_legacy registered [ 1.322644] Key type asymmetric registered [ 1.324830] Asymmetric key parser 'x509' registered [ 1.329815] bounce: pool size: 64 pages [ 1.333622] io scheduler noop registered (default) [ 1.338264] io scheduler mq-deadline registered [ 1.342793] io scheduler kyber registered [ 1.348576] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.353618] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 1.360515] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 1.376919] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 1.380624] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 1.390554] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 1.401392] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.408369] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 1.413953] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.419723] iommu: Adding device serial8250 to group 65 [ 1.426661] console [ttyS0] disabled [ 1.428410] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.437388] console [ttyS0] enabled [ 1.437388] console [ttyS0] enabled [ 1.443919] bootconsole [earlycon0] disabled [ 1.443919] bootconsole [earlycon0] disabled [ 1.452949] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.463970] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.492616] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.512190] loop: module loaded [ 1.516687] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.524128] as3722 4-0040: AS3722 with revision 0x1 found [ 1.531738] iommu: Adding device as3722-pinctrl to group 66 [ 1.538988] iommu: Adding device as3722-regulator to group 67 [ 1.547653] as3722-sd2: supplied by +5V_SYS [ 1.552353] as3722-sd3: supplied by +5V_SYS [ 1.556776] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.563165] as3722-sd4: supplied by +5V_SYS [ 1.567822] as3722-sd5: supplied by +5V_SYS [ 1.573939] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.580040] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.586300] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.592254] as3722-ldo3: supplied by +3.3V_SYS [ 1.596749] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.604585] as3722-ldo4: supplied by +3.3V_SYS [ 1.609255] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.615520] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.620361] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.627336] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.633012] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.639191] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.649399] iommu: Adding device as3722-rtc to group 68 [ 1.654833] iommu: Adding device as3722-adc to group 69 [ 1.660198] iommu: Adding device as3722-power-off to group 70 [ 1.666116] iommu: Adding device as3722-wdt to group 71 [ 1.672141] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.690741] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.707517] iommu: Adding device Fixed MDIO bus.0 to group 72 [ 1.713470] libphy: Fixed MDIO Bus: probed [ 1.717562] CAN device driver interface [ 1.721464] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.728415] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.734137] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.741604] usbcore: registered new interface driver pegasus [ 1.747321] usbcore: registered new interface driver asix [ 1.752797] usbcore: registered new interface driver ax88179_178a [ 1.758932] usbcore: registered new interface driver cdc_ether [ 1.764856] usbcore: registered new interface driver smsc75xx [ 1.770659] usbcore: registered new interface driver smsc95xx [ 1.776470] usbcore: registered new interface driver net1080 [ 1.782197] usbcore: registered new interface driver cdc_subset [ 1.788157] usbcore: registered new interface driver zaurus [ 1.793823] usbcore: registered new interface driver cdc_ncm [ 1.799721] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.805374] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.811087] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.817606] ehci-pci: EHCI PCI platform driver [ 1.822131] tegra-ehci: Tegra EHCI driver [ 1.828981] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.834423] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.842239] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 1.871039] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.877860] hub 1-0:1.0: USB hub found [ 1.881672] hub 1-0:1.0: 1 port detected [ 1.886833] usbcore: registered new interface driver cdc_acm [ 1.892507] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.900564] usbcore: registered new interface driver cdc_wdm [ 1.906319] usbcore: registered new interface driver usb-storage [ 1.913972] iommu: Adding device ci_hdrc.0 to group 73 [ 1.925927] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.932827] as3722-rtc as3722-rtc: RTC interrupt 379 [ 1.940605] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.947807] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.954349] i2c /dev entries driver [ 1.959091] usbcore: registered new interface driver uvcvideo [ 1.964855] USB Video Class driver (1.1.1) [ 1.968947] gspca_main: v2.14.0 registered [ 1.973702] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.983986] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) [ 1.992476] iommu: Adding device cpufreq-tegra124 to group 74 [ 1.998787] sdhci: Secure Digital Host Controller Interface driver [ 2.004982] sdhci: Copyright(c) Pierre Ossman [ 2.009333] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.015335] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.020225] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.041063] mmc0: Unknown controller version (3). You may experience problems. [ 2.048320] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.083631] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.091773] usbcore: registered new interface driver usbhid [ 2.097337] usbhid: USB HID core driver [ 2.103857] iommu: Adding device snd-soc-dummy to group 75 [ 2.148143] mmc0: new high speed MMC card at address 0001 [ 2.154145] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.159076] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.165428] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.171597] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (247:0) [ 2.180590] mmcblk0: p1 [ 2.541444] iommu: Adding device 70301100.i2s to group 76 [ 2.547719] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub [ 2.567977] tegra-snd-rt5640 sound: rt5640-aif1 <-> 70301100.i2s mapping ok [ 2.578926] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input0 [ 2.590091] NET: Registered protocol family 10 [ 2.595956] Segment Routing with IPv6 [ 2.599796] mip6: Mobile IPv6 [ 2.602793] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.610184] NET: Registered protocol family 17 [ 2.614665] NET: Registered protocol family 15 [ 2.619104] can: controller area network core (rev 20170425 abi 9) [ 2.625561] NET: Registered protocol family 29 [ 2.630001] can: raw protocol (rev 20170425) [ 2.634290] can: broadcast manager protocol (rev 20170425 t) [ 2.639951] can: netlink gateway (rev 20170425) max_hops=1 [ 2.645630] Bluetooth: RFCOMM socket layer initialized [ 2.650779] Bluetooth: RFCOMM ver 1.11 [ 2.654597] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.659922] Bluetooth: BNEP socket layer initialized [ 2.664899] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.670817] Bluetooth: HIDP socket layer initialized [ 2.676015] Key type dns_resolver registered [ 2.680784] Registering SWP/SWPB emulation handler [ 2.686457] Loading compiled-in X.509 certificates [ 2.708839] +3.3V_RUN: supplied by +3.3V_SYS [ 2.714143] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.718837] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.724872] +5V_USB_HS: supplied by +5V_SYS [ 2.730000] +3.3V_LP0: supplied by +3.3V_SYS [ 2.735284] +5V_HDMI_CON: supplied by +5V_SYS [ 2.740055] +5V_SATA: supplied by +5V_SYS [ 2.744796] +12V_SATA: supplied by +VDD_MUX [ 2.750398] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.757291] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.764418] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.772019] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.777632] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.786759] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.795483] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.804357] as3722-sd2: supplied by +5V_SYS [ 2.808845] as3722-sd3: supplied by +5V_SYS [ 2.813381] as3722-sd4: supplied by +5V_SYS [ 2.817865] as3722-sd5: supplied by +5V_SYS [ 2.823748] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.829232] as3722-ldo1: supplied by +3.3V_RUN [ 2.834500] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.840043] as3722-ldo3: supplied by +3.3V_SYS [ 2.845586] as3722-ldo4: supplied by +3.3V_SYS [ 2.850340] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.855290] as3722-ldo6: supplied by +3.3V_RUN [ 2.860044] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.865507] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.872202] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 [ 2.881462] as3722-ldo9: supplied by +5V_SYS [ 2.886185] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.892633] as3722-ldo10: supplied by +5V_SYS [ 2.897223] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.903722] as3722-ldo11: supplied by +3.3V_RUN [ 2.908482] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.917409] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.926472] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.936603] scsi host0: tegra-ahci [ 2.940886] scsi host1: tegra-ahci [ 2.944628] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.952650] ata2: DUMMY [ 2.956503] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.961963] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.969775] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 3.001138] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 3.008134] hub 2-0:1.0: USB hub found [ 3.012060] hub 2-0:1.0: 1 port detected [ 3.029325] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 [ 3.039125] tegra-xusb 70090000.usb: failed to request firmware: -2 [ 3.045532] tegra-xusb 70090000.usb: failed to load firmware: -2 [ 3.052186] tegra-xusb: probe of 70090000.usb failed with error -2 [ 3.059198] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 3.064177] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 3.077463] mmc1: Unknown controller version (3). You may experience problems. [ 3.084838] mmc1: Invalid maximum block size, assuming 512 bytes [ 3.121415] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 3.129119] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 3.136448] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 3.144101] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 3.169425] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 3.177762] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 3.191789] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.198073] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.204375] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.211392] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.218790] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.224383] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 3.230416] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.240175] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.249984] pci 0000:00:01.0: enabling Extended Tags [ 3.255074] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.264891] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.274788] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.281549] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.284712] ata1: SATA link down (SStatus 0 SControl 300) [ 3.297174] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.303241] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.312971] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.322785] pci 0000:00:02.0: enabling Extended Tags [ 3.327800] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.337576] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.347416] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.354174] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.364295] PCI: bus0: Fast back to back transfers disabled [ 3.369951] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.378032] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.386341] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.392470] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.399597] PCI: bus1: Fast back to back transfers disabled [ 3.405252] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.412145] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.418244] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.423929] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.430909] mmc1: new high speed SDHC card at address aaaa [ 3.437023] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.442083] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.449902] PCI: bus2: Fast back to back transfers disabled [ 3.455598] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.462443] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.469298] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.476275] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.484125] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.490379] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.497818] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.503080] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.509956] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.517997] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.525431] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.531713] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.536746] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.543034] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.549889] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.557855] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.565169] mmcblk1: p1 p2 p3 [ 3.568500] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.575447] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.582079] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.589167] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.595704] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.601943] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.607559] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.613500] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.652809] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf09dc000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.662399] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.674582] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.683947] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.690574] [drm] No driver support for vblank timestamp query. [ 3.829442] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 4.076694] Console: switching to colour frame buffer device 512x135 [ 4.172550] drm drm: fb0: frame buffer device [ 4.177079] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 4.184451] iommu: Adding device cpufreq-dt.0 to group 77 [ 4.190123] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 4.197469] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 4.206504] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [ 4.213989] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:14 UTC (946684814) [ 4.222770] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.232409] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.239026] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.247672] cfg80211: failed to load regulatory.db [ 4.248013] +USB0_VBUS_SW: disabling [ 4.248030] +1.8V_RUN_CAM: disabling [ 4.252602] +2.8V_RUN_CAM: disabling [ 4.256226] +1.2V_RUN_CAM_FRONT: disabling [ 4.259821] +1.05V_RUN_CAM_REAR: disabling [ 4.263417] +3.3V_RUN_TOUCH: disabling [ 4.267530] +2.8V_RUN_CAM_AF: disabling [ 4.271665] +1.8V_RUN_VPP_FUSE: disabling [ 4.275411] ALSA device list: [ 4.275414] #0: tegra-hda at 0x70038000 irq 346 [ 4.275415] #1: NVIDIA Tegra Jetson TK1 [ 4.295749] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.341585] EXT4-fs (mmcblk0p1): recovery complete [ 4.347510] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.355672] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.366522] devtmpfs: mounted [ 4.369850] Freeing unused kernel memory: 1024K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#