U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.tegra_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.tegra_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################### 3.9 MiB/s done Bytes transferred = 6166048 (5e1620 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.7 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x5e1620 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-next-20171122-14139-g1efc584 (jonathanh@kaivo) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP PREEMPT Tue Nov 21 18:17:25 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0xfbc00000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @eef88000 s39360 r8192 d22080 u69632 [ 0.000000] pcpu-alloc: s39360 r8192 d22080 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1998492K/2096128K available (9216K kernel code, 778K rwdata, 2560K rodata, 1024K init, 299K bss, 32100K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB) [ 0.000000] .init : 0xc0d00000 - 0xc0e00000 (1024 kB) [ 0.000000] .data : 0xc0e00000 - 0xc0ec2860 ( 779 kB) [ 0.000000] .bss : 0xc0ec2860 - 0xc0f0d4f4 ( 300 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.007469] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.016999] Switching to timer-based delay loop, resolution 1000ns [ 0.024172] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.029221] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.039969] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.047937] Switching to timer-based delay loop, resolution 83ns [ 0.054405] Console: colour dummy device 80x30 [ 0.058353] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.068661] pid_max: default: 32768 minimum: 301 [ 0.073737] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.079847] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.087685] CPU: Testing write buffer coherency: ok [ 0.092010] /cpus/cpu@0 missing clock-frequency property [ 0.097020] /cpus/cpu@1 missing clock-frequency property [ 0.102326] /cpus/cpu@2 missing clock-frequency property [ 0.107594] /cpus/cpu@3 missing clock-frequency property [ 0.112865] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152975] Setting up static identity map for 0x80100000 - 0x801000a0 [ 0.157727] Hierarchical SRCU implementation. [ 0.173482] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.192995] smp: Bringing up secondary CPUs ... [ 0.243625] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.323732] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.403842] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.413416] smp: Brought up 1 node, 4 CPUs [ 0.432504] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.438671] CPU: All CPU(s) started in SVC mode. [ 0.445119] devtmpfs: initialized [ 0.465271] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.471389] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.480828] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.488311] pinctrl core: initialized pinctrl subsystem [ 0.493369] NET: Registered protocol family 16 [ 0.498046] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.504740] cpuidle: using governor menu [ 0.530432] No ATAGs? [ 0.530567] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.538928] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.546580] iommu: Adding device reg-dummy to group 0 [ 0.549805] iommu: Adding device 1003000.pcie to group 1 [ 0.555107] iommu: Adding device 50000000.host1x to group 2 [ 0.560661] iommu: Adding device 54200000.dc to group 3 [ 0.565842] iommu: Adding device 54240000.dc to group 4 [ 0.571026] iommu: Adding device 54280000.hdmi to group 5 [ 0.576415] iommu: Adding device 57000000.gpu to group 6 [ 0.581687] iommu: Adding device 60005000.timer to group 7 [ 0.587121] iommu: Adding device 60007000.flow-controller to group 8 [ 0.593465] iommu: Adding device 6000c800.actmon to group 9 [ 0.598995] iommu: Adding device 6000d000.gpio to group 10 [ 0.604472] iommu: Adding device 60020000.dma to group 11 [ 0.609844] iommu: Adding device 70000800.apbmisc to group 12 [ 0.615566] iommu: Adding device 70000868.pinmux to group 13 [ 0.621185] iommu: Adding device 70006000.serial to group 14 [ 0.626833] iommu: Adding device 70006040.serial to group 15 [ 0.632446] iommu: Adding device 70006300.serial to group 16 [ 0.638100] iommu: Adding device 7000c000.i2c to group 17 [ 0.643454] iommu: Adding device 7000c400.i2c to group 18 [ 0.648844] iommu: Adding device 7000c500.i2c to group 19 [ 0.654201] iommu: Adding device 7000c700.i2c to group 20 [ 0.659599] iommu: Adding device 7000d000.i2c to group 21 [ 0.664946] iommu: Adding device 7000d400.spi to group 22 [ 0.670345] iommu: Adding device 7000da00.spi to group 23 [ 0.675695] iommu: Adding device 7000e000.rtc to group 24 [ 0.681086] iommu: Adding device 7000e400.pmc to group 25 [ 0.686439] iommu: Adding device 7000f800.fuse to group 26 [ 0.691918] iommu: Adding device 70019000.memory-controller to group 27 [ 0.698489] iommu: Adding device 7001b000.emc to group 28 [ 0.703884] iommu: Adding device 70027000.sata to group 29 [ 0.709320] iommu: Adding device 70030000.hda to group 30 [ 0.714714] iommu: Adding device 70090000.usb to group 31 [ 0.720069] iommu: Adding device 7009f000.padctl to group 32 [ 0.725733] iommu: Adding device 700b0400.sdhci to group 33 [ 0.731247] iommu: Adding device 700b0600.sdhci to group 34 [ 0.736813] iommu: Adding device 70015000.cec to group 35 [ 0.742180] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.748515] iommu: Adding device 70110000.clock to group 37 [ 0.754040] iommu: Adding device 70300000.ahub to group 38 [ 0.759519] iommu: Adding device 7d000000.usb to group 39 [ 0.764874] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.770612] iommu: Adding device 7d004000.usb to group 41 [ 0.775968] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.781709] iommu: Adding device 7d008000.usb to group 43 [ 0.787066] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.792798] iommu: Adding device pmu to group 45 [ 0.797374] iommu: Adding device timer to group 46 [ 0.802140] iommu: Adding device clocks to group 47 [ 0.807011] iommu: Adding device gpio-keys to group 48 [ 0.812107] iommu: Adding device regulators to group 49 [ 0.817333] iommu: Adding device regulators:regulator@0 to group 50 [ 0.823548] iommu: Adding device regulators:regulator@1 to group 51 [ 0.829807] iommu: Adding device regulators:regulator@2 to group 52 [ 0.836027] iommu: Adding device regulators:regulator@3 to group 53 [ 0.842284] iommu: Adding device regulators:regulator@4 to group 54 [ 0.848514] iommu: Adding device regulators:regulator@7 to group 55 [ 0.854765] iommu: Adding device regulators:regulator@8 to group 56 [ 0.860995] iommu: Adding device regulators:regulator@10 to group 57 [ 0.867331] iommu: Adding device regulators:regulator@11 to group 58 [ 0.873640] iommu: Adding device regulators:regulator@12 to group 59 [ 0.879985] iommu: Adding device regulators:regulator@13 to group 60 [ 0.886294] iommu: Adding device regulators:regulator@14 to group 61 [ 0.892637] iommu: Adding device sound to group 62 [ 0.914267] +5V_SYS: supplied by +VDD_MUX [ 0.916757] +3.3V_SYS: supplied by +VDD_MUX [ 0.921317] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.926640] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.934761] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.940485] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.948717] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.955505] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.963706] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.969518] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.977743] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.983297] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.991524] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.997161] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 1.006598] vgaarb: loaded [ 1.008746] SCSI subsystem initialized [ 1.011942] libata version 3.00 loaded. [ 1.015837] usbcore: registered new interface driver usbfs [ 1.021059] usbcore: registered new interface driver hub [ 1.026364] usbcore: registered new device driver usb [ 1.034545] Linux video capture interface: v2.00 [ 1.037327] pps_core: LinuxPPS API ver. 1 registered [ 1.042225] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.051331] PTP clock support registered [ 1.056634] Advanced Linux Sound Architecture Driver Initialized. [ 1.061904] Bluetooth: Core ver 2.22 [ 1.064863] NET: Registered protocol family 31 [ 1.069259] Bluetooth: HCI device and connection manager initialized [ 1.075564] Bluetooth: HCI socket layer initialized [ 1.080436] Bluetooth: L2CAP socket layer initialized [ 1.085471] Bluetooth: SCO socket layer initialized [ 1.090947] clocksource: Switched to clocksource arch_sys_counter [ 1.186166] NET: Registered protocol family 2 [ 1.189617] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.195756] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.202241] TCP: Hash tables configured (established 8192 bind 8192) [ 1.208857] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.214327] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.220907] NET: Registered protocol family 1 [ 1.225666] RPC: Registered named UNIX socket transport module. [ 1.230820] RPC: Registered udp transport module. [ 1.235526] RPC: Registered tcp transport module. [ 1.240180] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.247053] iommu: Adding device regulatory.0 to group 63 [ 1.252183] PCI: CLS 0 bytes, default 64 [ 1.257674] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 1.264750] iommu: Adding device alarmtimer to group 64 [ 1.270356] Initialise system trusted keyrings [ 1.273848] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 1.281477] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.286609] NFS: Registering the id_resolver key type [ 1.290899] Key type id_resolver registered [ 1.295073] Key type id_legacy registered [ 1.303921] Key type asymmetric registered [ 1.306108] Asymmetric key parser 'x509' registered [ 1.311115] bounce: pool size: 64 pages [ 1.314847] io scheduler noop registered (default) [ 1.319541] io scheduler mq-deadline registered [ 1.324092] io scheduler kyber registered [ 1.329849] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 1.334867] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 1.341857] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 1.357719] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 1.361483] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 1.371369] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 1.382159] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.389108] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 1.394684] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.400491] iommu: Adding device serial8250 to group 65 [ 1.407443] console [ttyS0] disabled [ 1.409175] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.418144] console [ttyS0] enabled [ 1.418144] console [ttyS0] enabled [ 1.424347] bootconsole [earlycon0] disabled [ 1.424347] bootconsole [earlycon0] disabled [ 1.434046] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.444755] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.473271] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.492843] loop: module loaded [ 1.497331] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.504783] as3722 4-0040: AS3722 with revision 0x1 found [ 1.512445] iommu: Adding device as3722-pinctrl to group 66 [ 1.519706] iommu: Adding device as3722-regulator to group 67 [ 1.528401] as3722-sd2: supplied by +5V_SYS [ 1.533116] as3722-sd3: supplied by +5V_SYS [ 1.537541] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.543927] as3722-sd4: supplied by +5V_SYS [ 1.548591] as3722-sd5: supplied by +5V_SYS [ 1.554705] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.560809] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.567073] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.573036] as3722-ldo3: supplied by +3.3V_SYS [ 1.577531] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.585363] as3722-ldo4: supplied by +3.3V_SYS [ 1.590034] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.596305] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.601170] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.608115] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.613790] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.619970] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.630203] iommu: Adding device as3722-rtc to group 68 [ 1.635634] iommu: Adding device as3722-adc to group 69 [ 1.641025] iommu: Adding device as3722-power-off to group 70 [ 1.646912] iommu: Adding device as3722-wdt to group 71 [ 1.652938] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.671595] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.678292] iommu: Adding device Fixed MDIO bus.0 to group 72 [ 1.684274] libphy: Fixed MDIO Bus: probed [ 1.688367] CAN device driver interface [ 1.692272] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.699223] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.704978] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.712465] usbcore: registered new interface driver pegasus [ 1.718186] usbcore: registered new interface driver asix [ 1.723691] usbcore: registered new interface driver ax88179_178a [ 1.729827] usbcore: registered new interface driver cdc_ether [ 1.735749] usbcore: registered new interface driver smsc75xx [ 1.741601] usbcore: registered new interface driver smsc95xx [ 1.747390] usbcore: registered new interface driver net1080 [ 1.753119] usbcore: registered new interface driver cdc_subset [ 1.759081] usbcore: registered new interface driver zaurus [ 1.764781] usbcore: registered new interface driver cdc_ncm [ 1.770677] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.776323] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.782043] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.788563] ehci-pci: EHCI PCI platform driver [ 1.793087] tegra-ehci: Tegra EHCI driver [ 1.799936] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.805376] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.813190] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 1.840979] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.847800] hub 1-0:1.0: USB hub found [ 1.851613] hub 1-0:1.0: 1 port detected [ 1.856776] usbcore: registered new interface driver cdc_acm [ 1.862448] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.870508] usbcore: registered new interface driver cdc_wdm [ 1.876261] usbcore: registered new interface driver usb-storage [ 1.883890] iommu: Adding device ci_hdrc.0 to group 73 [ 1.895809] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.902707] as3722-rtc as3722-rtc: RTC interrupt 379 [ 1.910504] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.917704] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.924243] i2c /dev entries driver [ 1.928987] usbcore: registered new interface driver uvcvideo [ 1.934749] USB Video Class driver (1.1.1) [ 1.938840] gspca_main: v2.14.0 registered [ 1.943588] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.953852] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) [ 1.962348] iommu: Adding device cpufreq-tegra124 to group 74 [ 1.968661] sdhci: Secure Digital Host Controller Interface driver [ 1.974855] sdhci: Copyright(c) Pierre Ossman [ 1.979206] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.985197] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.990088] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.011001] mmc0: Unknown controller version (3). You may experience problems. [ 2.018258] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.081019] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.092505] usbcore: registered new interface driver usbhid [ 2.098177] usbhid: USB HID core driver [ 2.105059] iommu: Adding device snd-soc-dummy to group 75 [ 2.157387] mmc0: new high speed MMC card at address 0001 [ 2.163397] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.168312] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.174696] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.180802] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (247:0) [ 2.189819] mmcblk0: p1 [ 2.551380] iommu: Adding device 70301100.i2s to group 76 [ 2.557637] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub [ 2.577966] tegra-snd-rt5640 sound: rt5640-aif1 <-> 70301100.i2s mapping ok [ 2.588756] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input0 [ 2.599955] NET: Registered protocol family 10 [ 2.605757] Segment Routing with IPv6 [ 2.609590] mip6: Mobile IPv6 [ 2.612579] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.619990] NET: Registered protocol family 17 [ 2.624508] NET: Registered protocol family 15 [ 2.628961] can: controller area network core (rev 20170425 abi 9) [ 2.635358] NET: Registered protocol family 29 [ 2.639799] can: raw protocol (rev 20170425) [ 2.644081] can: broadcast manager protocol (rev 20170425 t) [ 2.649740] can: netlink gateway (rev 20170425) max_hops=1 [ 2.655504] Bluetooth: RFCOMM socket layer initialized [ 2.660654] Bluetooth: RFCOMM ver 1.11 [ 2.664441] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.669753] Bluetooth: BNEP socket layer initialized [ 2.674729] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.680646] Bluetooth: HIDP socket layer initialized [ 2.685886] Key type dns_resolver registered [ 2.690654] Registering SWP/SWPB emulation handler [ 2.696250] Loading compiled-in X.509 certificates [ 2.718922] +3.3V_RUN: supplied by +3.3V_SYS [ 2.724058] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.728761] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.734794] +5V_USB_HS: supplied by +5V_SYS [ 2.739886] +3.3V_LP0: supplied by +3.3V_SYS [ 2.745232] +5V_HDMI_CON: supplied by +5V_SYS [ 2.750007] +5V_SATA: supplied by +5V_SYS [ 2.754674] +12V_SATA: supplied by +VDD_MUX [ 2.760303] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.767183] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.774377] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.781906] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.787519] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.796650] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.805503] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.816052] as3722-sd2: supplied by +5V_SYS [ 2.820615] as3722-sd3: supplied by +5V_SYS [ 2.825150] as3722-sd4: supplied by +5V_SYS [ 2.829631] as3722-sd5: supplied by +5V_SYS [ 2.835499] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.841499] as3722-ldo1: supplied by +3.3V_RUN [ 2.846246] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.851918] as3722-ldo3: supplied by +3.3V_SYS [ 2.857296] as3722-ldo4: supplied by +3.3V_SYS [ 2.862093] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.867011] as3722-ldo6: supplied by +3.3V_RUN [ 2.872801] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 [ 2.881426] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.886965] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.894111] as3722-ldo9: supplied by +5V_SYS [ 2.899574] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.906332] as3722-ldo10: supplied by +5V_SYS [ 2.911446] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.918271] as3722-ldo11: supplied by +3.3V_RUN [ 2.923584] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.932846] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.941912] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.952456] scsi host0: tegra-ahci [ 2.956870] scsi host1: tegra-ahci [ 2.960572] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.968615] ata2: DUMMY [ 2.972319] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.977765] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.985649] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 3.021077] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 3.028190] hub 2-0:1.0: USB hub found [ 3.032061] hub 2-0:1.0: 1 port detected [ 3.048964] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 [ 3.058773] tegra-xusb 70090000.usb: failed to request firmware: -2 [ 3.065090] tegra-xusb 70090000.usb: failed to load firmware: -2 [ 3.071826] tegra-xusb: probe of 70090000.usb failed with error -2 [ 3.078847] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 3.083795] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 3.095224] mmc1: Unknown controller version (3). You may experience problems. [ 3.102563] mmc1: Invalid maximum block size, assuming 512 bytes [ 3.171587] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 3.179268] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 3.190176] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 3.198525] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 3.221824] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 3.230123] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 3.244164] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 3.250446] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.256682] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 3.263670] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 3.271117] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.276742] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 3.282818] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.292529] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.302320] pci 0000:00:01.0: enabling Extended Tags [ 3.304426] ata1: SATA link down (SStatus 0 SControl 300) [ 3.312932] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.322711] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.332500] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.339111] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.349265] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.355339] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.365002] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.374690] pci 0000:00:02.0: enabling Extended Tags [ 3.379654] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.389456] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.399293] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.405977] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.416066] PCI: bus0: Fast back to back transfers disabled [ 3.421716] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.429782] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.438076] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.444214] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.451350] PCI: bus1: Fast back to back transfers disabled [ 3.456986] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.463883] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.469983] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.475767] mmc1: new high speed SDHC card at address aaaa [ 3.481855] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.486946] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.493863] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.501700] PCI: bus2: Fast back to back transfers disabled [ 3.507334] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.514188] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.521084] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.528024] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.535871] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.542173] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.549570] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.554824] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.561739] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.569743] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.577179] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.583471] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.588502] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.594801] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.601695] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.609625] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.616940] mmcblk1: p1 p2 p3 [ 3.620271] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.627172] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.633797] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.640880] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.647410] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.653638] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.659252] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.665186] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.702763] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf09dc000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.712352] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.724525] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.733950] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.740577] [drm] No driver support for vblank timestamp query. [ 3.876933] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 4.125098] Console: switching to colour frame buffer device 512x135 [ 4.222287] drm drm: fb0: frame buffer device [ 4.226884] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 4.234189] iommu: Adding device cpufreq-dt.0 to group 77 [ 4.239867] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 4.247213] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 4.256243] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [ 4.263635] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:13 UTC (946684813) [ 4.272392] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.281800] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.288418] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.297074] cfg80211: failed to load regulatory.db [ 4.297429] +USB0_VBUS_SW: disabling [ 4.297446] +1.8V_RUN_CAM: disabling [ 4.302000] +2.8V_RUN_CAM: disabling [ 4.305622] +1.2V_RUN_CAM_FRONT: disabling [ 4.309215] +1.05V_RUN_CAM_REAR: disabling [ 4.312811] +3.3V_RUN_TOUCH: disabling [ 4.316920] +2.8V_RUN_CAM_AF: disabling [ 4.321074] +1.8V_RUN_VPP_FUSE: disabling [ 4.324807] ALSA device list: [ 4.324810] #0: tegra-hda at 0x70038000 irq 346 [ 4.324813] #1: NVIDIA Tegra Jetson TK1 [ 4.345205] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.392406] EXT4-fs (mmcblk0p1): recovery complete [ 4.398253] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.406417] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.417290] devtmpfs: mounted [ 4.420633] Freeing unused kernel memory: 1024K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#