U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################# 3.8 MiB/s done Bytes transferred = 8057344 (7af200 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 2.5 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7af200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-next-20171116-333567-g785be731fbc6 (jonathanh@tamien) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Wed Nov 15 20:18:22 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c16807c0, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @eef87000 s39168 r8192 d22272 u69632 [ 0.000000] pcpu-alloc: s39168 r8192 d22272 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1992440K/2096128K available (11264K kernel code, 1602K rwdata, 4296K rodata, 2048K init, 404K bss, 38152K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e00000 (12256 kB) [ 0.000000] .init : 0xc1300000 - 0xc1500000 (2048 kB) [ 0.000000] .data : 0xc1500000 - 0xc1690800 (1602 kB) [ 0.000000] .bss : 0xc1690800 - 0xc16f5bb4 ( 405 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000043] Switching to timer-based delay loop, resolution 1000ns [ 0.005662] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005680] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005700] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005714] Switching to timer-based delay loop, resolution 83ns [ 0.006210] Console: colour dummy device 80x30 [ 0.006243] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.006261] pid_max: default: 32768 minimum: 301 [ 0.006376] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006391] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006890] CPU: Testing write buffer coherency: ok [ 0.007149] /cpus/cpu@0 missing clock-frequency property [ 0.007193] /cpus/cpu@1 missing clock-frequency property [ 0.007237] /cpus/cpu@2 missing clock-frequency property [ 0.007282] /cpus/cpu@3 missing clock-frequency property [ 0.007296] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007593] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.009610] Hierarchical SRCU implementation. [ 0.011585] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.012393] EFI services will not be available. [ 0.012548] smp: Bringing up secondary CPUs ... [ 0.013117] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.016175] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.026200] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035658] smp: Brought up 1 node, 4 CPUs [ 0.035679] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035688] CPU: All CPU(s) started in SVC mode. [ 0.037202] devtmpfs: initialized [ 0.050725] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.051106] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.051124] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052571] pinctrl core: initialized pinctrl subsystem [ 0.054124] DMI not present or invalid. [ 0.054369] NET: Registered protocol family 16 [ 0.056583] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.059008] cpuidle: using governor menu [ 0.084596] No ATAGs? [ 0.084724] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.084741] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.092362] Serial: AMBA PL011 UART driver [ 0.093776] iommu: Adding device reg-dummy to group 0 [ 0.093815] iommu: Adding device 1003000.pcie to group 1 [ 0.093890] iommu: Adding device 50000000.host1x to group 2 [ 0.093961] iommu: Adding device 54200000.dc to group 3 [ 0.094029] iommu: Adding device 54240000.dc to group 4 [ 0.094061] iommu: Adding device 54280000.hdmi to group 5 [ 0.094130] iommu: Adding device 57000000.gpu to group 6 [ 0.094164] iommu: Adding device 60005000.timer to group 7 [ 0.094195] iommu: Adding device 60007000.flow-controller to group 8 [ 0.094230] iommu: Adding device 6000c800.actmon to group 9 [ 0.094262] iommu: Adding device 6000d000.gpio to group 10 [ 0.094293] iommu: Adding device 60020000.dma to group 11 [ 0.094323] iommu: Adding device 70000800.apbmisc to group 12 [ 0.094354] iommu: Adding device 70000868.pinmux to group 13 [ 0.094385] iommu: Adding device 70006000.serial to group 14 [ 0.094416] iommu: Adding device 70006040.serial to group 15 [ 0.094450] iommu: Adding device 70006300.serial to group 16 [ 0.094481] iommu: Adding device 7000c000.i2c to group 17 [ 0.094512] iommu: Adding device 7000c400.i2c to group 18 [ 0.094547] iommu: Adding device 7000c500.i2c to group 19 [ 0.094578] iommu: Adding device 7000c700.i2c to group 20 [ 0.094609] iommu: Adding device 7000d000.i2c to group 21 [ 0.094641] iommu: Adding device 7000d400.spi to group 22 [ 0.094672] iommu: Adding device 7000da00.spi to group 23 [ 0.094706] iommu: Adding device 7000e000.rtc to group 24 [ 0.094737] iommu: Adding device 7000e400.pmc to group 25 [ 0.094767] iommu: Adding device 7000f800.fuse to group 26 [ 0.094798] iommu: Adding device 70019000.memory-controller to group 27 [ 0.094828] iommu: Adding device 7001b000.emc to group 28 [ 0.094859] iommu: Adding device 70027000.sata to group 29 [ 0.094894] iommu: Adding device 70030000.hda to group 30 [ 0.094929] iommu: Adding device 70090000.usb to group 31 [ 0.094960] iommu: Adding device 7009f000.padctl to group 32 [ 0.094995] iommu: Adding device 700b0400.sdhci to group 33 [ 0.095026] iommu: Adding device 700b0600.sdhci to group 34 [ 0.095057] iommu: Adding device 70015000.cec to group 35 [ 0.095087] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.095119] iommu: Adding device 70110000.clock to group 37 [ 0.095151] iommu: Adding device 70300000.ahub to group 38 [ 0.095181] iommu: Adding device 7d000000.usb to group 39 [ 0.095212] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.095250] iommu: Adding device 7d004000.usb to group 41 [ 0.095281] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.095311] iommu: Adding device 7d008000.usb to group 43 [ 0.095342] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.095373] iommu: Adding device pmu to group 45 [ 0.095403] iommu: Adding device timer to group 46 [ 0.095433] iommu: Adding device clocks to group 47 [ 0.095465] iommu: Adding device gpio-keys to group 48 [ 0.095500] iommu: Adding device regulators to group 49 [ 0.095531] iommu: Adding device regulators:regulator@0 to group 50 [ 0.095566] iommu: Adding device regulators:regulator@1 to group 51 [ 0.095597] iommu: Adding device regulators:regulator@2 to group 52 [ 0.095628] iommu: Adding device regulators:regulator@3 to group 53 [ 0.095659] iommu: Adding device regulators:regulator@4 to group 54 [ 0.095690] iommu: Adding device regulators:regulator@7 to group 55 [ 0.095751] iommu: Adding device regulators:regulator@8 to group 56 [ 0.095783] iommu: Adding device regulators:regulator@10 to group 57 [ 0.095819] iommu: Adding device regulators:regulator@11 to group 58 [ 0.095850] iommu: Adding device regulators:regulator@12 to group 59 [ 0.095881] iommu: Adding device regulators:regulator@13 to group 60 [ 0.095913] iommu: Adding device regulators:regulator@14 to group 61 [ 0.095950] iommu: Adding device sound to group 62 [ 0.110898] AT91: Could not find identification node [ 0.111460] +5V_SYS: supplied by +VDD_MUX [ 0.111747] +3.3V_SYS: supplied by +VDD_MUX [ 0.112354] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.112370] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.112470] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.112484] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.112668] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.112682] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.112778] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.112791] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.112886] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.112899] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.112995] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.113008] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.116059] vgaarb: loaded [ 0.116782] SCSI subsystem initialized [ 0.116959] libata version 3.00 loaded. [ 0.117155] usbcore: registered new interface driver usbfs [ 0.117203] usbcore: registered new interface driver hub [ 0.117263] usbcore: registered new device driver usb [ 0.120723] pps_core: LinuxPPS API ver. 1 registered [ 0.120734] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.120760] PTP clock support registered [ 0.120952] EDAC MC: Ver: 3.0.0 [ 0.123817] clocksource: Switched to clocksource arch_sys_counter [ 0.172762] NET: Registered protocol family 2 [ 0.173261] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.173362] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.173549] TCP: Hash tables configured (established 8192 bind 8192) [ 0.173635] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.173681] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.173860] NET: Registered protocol family 1 [ 0.174194] RPC: Registered named UNIX socket transport module. [ 0.174205] RPC: Registered udp transport module. [ 0.174214] RPC: Registered tcp transport module. [ 0.174222] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.174234] PCI: CLS 0 bytes, default 64 [ 0.175717] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.176463] iommu: Adding device alarmtimer to group 63 [ 0.177266] Initialise system trusted keyrings [ 0.177404] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.183862] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.184433] NFS: Registering the id_resolver key type [ 0.184453] Key type id_resolver registered [ 0.184462] Key type id_legacy registered [ 0.184504] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.186105] Key type asymmetric registered [ 0.186117] Asymmetric key parser 'x509' registered [ 0.186169] bounce: pool size: 64 pages [ 0.186221] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.186232] io scheduler noop registered [ 0.186242] io scheduler deadline registered [ 0.186458] io scheduler cfq registered (default) [ 0.186468] io scheduler mq-deadline registered [ 0.186478] io scheduler kyber registered [ 0.190510] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.190617] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.191000] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.210640] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.210697] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.217148] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.223629] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.227043] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.277385] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.277487] iommu: Adding device serial8250 to group 64 [ 0.280006] console [ttyS0] disabled [ 0.280045] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.552719] console [ttyS0] enabled [ 1.557137] SuperH (H)SCI(F) driver initialized [ 1.562790] msm_serial: driver initialized [ 1.567101] STMicroelectronics ASC driver initialized [ 1.572831] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.582098] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.613354] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.630341] brd: module loaded [ 1.639740] loop: module loaded [ 1.644126] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.652439] as3722 4-0040: AS3722 with revision 0x1 found [ 1.659755] iommu: Adding device as3722-pinctrl to group 65 [ 1.666834] iommu: Adding device as3722-regulator to group 66 [ 1.675454] as3722-sd2: supplied by +5V_SYS [ 1.680031] as3722-sd3: supplied by +5V_SYS [ 1.684440] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.690764] as3722-sd4: supplied by +5V_SYS [ 1.695366] as3722-sd5: supplied by +5V_SYS [ 1.701293] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.707336] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.713512] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.719382] as3722-ldo3: supplied by +3.3V_SYS [ 1.723891] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.731637] as3722-ldo4: supplied by +3.3V_SYS [ 1.736313] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.742485] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.747336] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.754255] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.759907] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.766103] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.776021] iommu: Adding device as3722-rtc to group 67 [ 1.781565] iommu: Adding device as3722-adc to group 68 [ 1.787114] iommu: Adding device as3722-power-off to group 69 [ 1.793152] iommu: Adding device as3722-wdt to group 70 [ 1.800239] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.822690] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.829682] iommu: Adding device Fixed MDIO bus.0 to group 71 [ 1.835806] libphy: Fixed MDIO Bus: probed [ 1.840845] CAN device driver interface [ 1.845742] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.852812] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.858650] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.864623] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.871572] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.881235] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.888679] usbcore: registered new interface driver pegasus [ 1.894382] usbcore: registered new interface driver asix [ 1.899800] usbcore: registered new interface driver ax88179_178a [ 1.905931] usbcore: registered new interface driver cdc_ether [ 1.911799] usbcore: registered new interface driver smsc75xx [ 1.917590] usbcore: registered new interface driver smsc95xx [ 1.923355] usbcore: registered new interface driver net1080 [ 1.929053] usbcore: registered new interface driver cdc_subset [ 1.935006] usbcore: registered new interface driver zaurus [ 1.940613] usbcore: registered new interface driver cdc_ncm [ 1.946521] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.952113] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.959605] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.966143] ehci-pci: EHCI PCI platform driver [ 1.970612] ehci-platform: EHCI generic platform driver [ 1.976060] ehci-orion: EHCI orion driver [ 1.980228] SPEAr-ehci: EHCI SPEAr driver [ 1.984394] ehci-st: EHCI STMicroelectronics driver [ 1.989406] ehci-exynos: EHCI EXYNOS driver [ 1.993744] ehci-atmel: EHCI Atmel driver [ 1.997907] tegra-ehci: Tegra EHCI driver [ 2.004760] tegra-ehci 7d004000.usb: EHCI Host Controller [ 2.010173] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 2.017959] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 2.053835] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 2.060440] hub 1-0:1.0: USB hub found [ 2.064243] hub 1-0:1.0: 1 port detected [ 2.068717] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.074918] ohci-pci: OHCI PCI platform driver [ 2.079396] ohci-platform: OHCI generic platform driver [ 2.084836] SPEAr-ohci: OHCI SPEAr driver [ 2.088990] ohci-st: OHCI STMicroelectronics driver [ 2.094031] ohci-atmel: OHCI Atmel driver [ 2.098845] usbcore: registered new interface driver usb-storage [ 2.106673] iommu: Adding device ci_hdrc.0 to group 72 [ 2.118942] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 2.125834] as3722-rtc as3722-rtc: RTC interrupt 379 [ 2.134261] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 2.141427] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 2.148191] i2c /dev entries driver [ 2.158860] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 2.174151] iommu: Adding device cpufreq-tegra124 to group 73 [ 2.182358] sdhci: Secure Digital Host Controller Interface driver [ 2.188550] sdhci: Copyright(c) Pierre Ossman [ 2.194721] Synopsys Designware Multimedia Card Interface Driver [ 2.202285] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.208771] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.213657] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.233859] mmc0: Unknown controller version (3). You may experience problems. [ 2.241115] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.303840] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.313446] ledtrig-cpu: registered to indicate activity on CPUs [ 2.319793] usbcore: registered new interface driver usbhid [ 2.325378] usbhid: USB HID core driver [ 2.333448] NET: Registered protocol family 10 [ 2.338860] Segment Routing with IPv6 [ 2.342616] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.349077] NET: Registered protocol family 17 [ 2.353526] can: controller area network core (rev 20170425 abi 9) [ 2.359771] NET: Registered protocol family 29 [ 2.364227] can: raw protocol (rev 20170425) [ 2.368492] can: broadcast manager protocol (rev 20170425 t) [ 2.374164] can: netlink gateway (rev 20170425) max_hops=1 [ 2.379927] Key type dns_resolver registered [ 2.384736] ThumbEE CPU extension supported. [ 2.389006] Registering SWP/SWPB emulation handler [ 2.394351] Loading compiled-in X.509 certificates [ 2.411813] +3.3V_RUN: supplied by +3.3V_SYS [ 2.417574] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.422200] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.428356] +5V_USB_HS: supplied by +5V_SYS [ 2.433898] +3.3V_LP0: supplied by +3.3V_SYS [ 2.440621] +5V_HDMI_CON: supplied by +5V_SYS [ 2.444622] mmc0: new high speed MMC card at address 0001 [ 2.445407] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.445937] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.446516] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.455273] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (237:0) [ 2.457581] mmcblk0: p1 [ 2.477411] +5V_SATA: supplied by +5V_SYS [ 2.481928] +12V_SATA: supplied by +VDD_MUX [ 2.487612] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.494490] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.501448] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.509502] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.515189] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.525095] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.535307] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.546695] as3722-sd2: supplied by +5V_SYS [ 2.551162] as3722-sd3: supplied by +5V_SYS [ 2.555705] as3722-sd4: supplied by +5V_SYS [ 2.560104] as3722-sd5: supplied by +5V_SYS [ 2.566332] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.572041] as3722-ldo1: supplied by +3.3V_RUN [ 2.576922] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.582488] as3722-ldo3: supplied by +3.3V_SYS [ 2.588019] as3722-ldo4: supplied by +3.3V_SYS [ 2.592692] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.597673] as3722-ldo6: supplied by +3.3V_RUN [ 2.602349] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.607758] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.614840] as3722-ldo9: supplied by +5V_SYS [ 2.620418] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.627010] as3722-ldo10: supplied by +5V_SYS [ 2.631933] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.638774] as3722-ldo11: supplied by +3.3V_RUN [ 2.644088] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.654194] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.663247] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.674129] scsi host0: tegra-ahci [ 2.678804] scsi host1: tegra-ahci [ 2.682437] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.690476] ata2: DUMMY [ 2.696551] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.701967] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.709745] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 2.743936] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.750670] hub 2-0:1.0: USB hub found [ 2.754531] hub 2-0:1.0: 1 port detected [ 2.761009] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.765961] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.778040] mmc1: Unknown controller version (3). You may experience problems. [ 2.785389] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.854410] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.862591] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.870202] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.879942] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.904153] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.912496] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.927257] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.933537] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.939761] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.946673] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.954032] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.959560] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.965621] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.975320] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.985053] pci 0000:00:01.0: enabling Extended Tags [ 2.990033] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.999830] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.009655] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.016315] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.026335] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.027577] ata1: SATA link down (SStatus 0 SControl 300) [ 3.037794] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.047493] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.057215] pci 0000:00:02.0: enabling Extended Tags [ 3.062182] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.071951] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.081732] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.088357] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.098348] PCI: bus0: Fast back to back transfers disabled [ 3.103938] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.111940] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.120140] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.126236] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.133303] PCI: bus1: Fast back to back transfers disabled [ 3.138894] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.145683] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.151711] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.157327] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.164152] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.171588] PCI: bus2: Fast back to back transfers disabled [ 3.177200] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.183872] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.190653] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.197453] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.205203] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.211295] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.218633] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.223598] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.230407] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.238173] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.245513] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.251621] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.256622] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.262713] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.269510] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.277293] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.284400] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.290726] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.296644] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.303696] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.310021] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.316105] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.321693] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.327579] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.350893] mmc1: new high speed SDHC card at address aaaa [ 3.357105] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.365421] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0a77000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.375036] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.387642] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.396593] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.403225] [drm] No driver support for vblank timestamp query. [ 3.415315] mmcblk1: p1 p2 p3 [ 3.534193] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.781343] Console: switching to colour frame buffer device 512x135 [ 3.879935] drm drm: fb0: frame buffer device [ 3.884475] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.892101] iommu: Adding device cpufreq-dt.0 to group 74 [ 3.897973] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.905314] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.914630] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.921932] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:04:35 UTC (946685075) [ 3.930917] +USB0_VBUS_SW: disabling [ 3.934539] +1.8V_RUN_CAM: disabling [ 3.938331] +2.8V_RUN_CAM: disabling [ 3.942058] +1.2V_RUN_CAM_FRONT: disabling [ 3.946394] +1.05V_RUN_CAM_REAR: disabling [ 3.950641] +3.3V_RUN_TOUCH: disabling [ 3.954605] +2.8V_RUN_CAM_AF: disabling [ 3.958596] +1.8V_RUN_VPP_FUSE: disabling [ 3.963706] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.010774] EXT4-fs (mmcblk0p1): recovery complete [ 4.016592] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.024729] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.032870] devtmpfs: mounted [ 4.036517] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#