U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################## 4 MiB/s done Bytes transferred = 8217088 (7d6200 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 4 MiB/s done Bytes transferred = 66544 (103f0 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7d6200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 830133ef Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-rc7-next-20171106-213365-g717d4dc (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Mon Nov 6 01:46:38 PST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c1680440, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @eef87000 s39744 r8192 d21696 u69632 [ 0.000000] pcpu-alloc: s39744 r8192 d21696 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1992440K/2096128K available (11264K kernel code, 1601K rwdata, 4552K rodata, 2048K init, 404K bss, 38152K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e00000 (12256 kB) [ 0.000000] .init : 0xc1300000 - 0xc1500000 (2048 kB) [ 0.000000] .data : 0xc1500000 - 0xc169044c (1602 kB) [ 0.000000] .bss : 0xc169044c - 0xc16f5834 ( 405 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000043] Switching to timer-based delay loop, resolution 1000ns [ 0.005447] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005466] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005485] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005499] Switching to timer-based delay loop, resolution 83ns [ 0.005981] Console: colour dummy device 80x30 [ 0.006014] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.006033] pid_max: default: 32768 minimum: 301 [ 0.006148] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006163] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006664] CPU: Testing write buffer coherency: ok [ 0.006927] /cpus/cpu@0 missing clock-frequency property [ 0.006970] /cpus/cpu@1 missing clock-frequency property [ 0.007014] /cpus/cpu@2 missing clock-frequency property [ 0.007059] /cpus/cpu@3 missing clock-frequency property [ 0.007072] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007370] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.009352] Hierarchical SRCU implementation. [ 0.011277] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.012055] EFI services will not be available. [ 0.012213] smp: Bringing up secondary CPUs ... [ 0.012705] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015888] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025913] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035445] smp: Brought up 1 node, 4 CPUs [ 0.035466] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035475] CPU: All CPU(s) started in SVC mode. [ 0.037006] devtmpfs: initialized [ 0.050512] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.050895] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.050913] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052356] pinctrl core: initialized pinctrl subsystem [ 0.053902] DMI not present or invalid. [ 0.054145] NET: Registered protocol family 16 [ 0.056339] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058741] cpuidle: using governor menu [ 0.084359] No ATAGs? [ 0.084489] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.084506] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.092045] Serial: AMBA PL011 UART driver [ 0.093454] iommu: Adding device reg-dummy to group 0 [ 0.093495] iommu: Adding device 1003000.pcie to group 1 [ 0.093570] iommu: Adding device 50000000.host1x to group 2 [ 0.093642] iommu: Adding device 54200000.dc to group 3 [ 0.093710] iommu: Adding device 54240000.dc to group 4 [ 0.093742] iommu: Adding device 54280000.hdmi to group 5 [ 0.093812] iommu: Adding device 57000000.gpu to group 6 [ 0.093848] iommu: Adding device 60005000.timer to group 7 [ 0.093879] iommu: Adding device 60007000.flow-controller to group 8 [ 0.093914] iommu: Adding device 6000c800.actmon to group 9 [ 0.093946] iommu: Adding device 6000d000.gpio to group 10 [ 0.093978] iommu: Adding device 60020000.dma to group 11 [ 0.094008] iommu: Adding device 70000800.apbmisc to group 12 [ 0.094039] iommu: Adding device 70000868.pinmux to group 13 [ 0.094070] iommu: Adding device 70006000.serial to group 14 [ 0.094102] iommu: Adding device 70006040.serial to group 15 [ 0.094138] iommu: Adding device 70006300.serial to group 16 [ 0.094168] iommu: Adding device 7000c000.i2c to group 17 [ 0.094198] iommu: Adding device 7000c400.i2c to group 18 [ 0.094235] iommu: Adding device 7000c500.i2c to group 19 [ 0.094267] iommu: Adding device 7000c700.i2c to group 20 [ 0.094298] iommu: Adding device 7000d000.i2c to group 21 [ 0.094331] iommu: Adding device 7000d400.spi to group 22 [ 0.094362] iommu: Adding device 7000da00.spi to group 23 [ 0.094396] iommu: Adding device 7000e000.rtc to group 24 [ 0.094427] iommu: Adding device 7000e400.pmc to group 25 [ 0.094458] iommu: Adding device 7000f800.fuse to group 26 [ 0.094489] iommu: Adding device 70019000.memory-controller to group 27 [ 0.094519] iommu: Adding device 7001b000.emc to group 28 [ 0.094551] iommu: Adding device 70027000.sata to group 29 [ 0.094586] iommu: Adding device 70030000.hda to group 30 [ 0.094622] iommu: Adding device 70090000.usb to group 31 [ 0.094653] iommu: Adding device 7009f000.padctl to group 32 [ 0.094688] iommu: Adding device 700b0400.sdhci to group 33 [ 0.094719] iommu: Adding device 700b0600.sdhci to group 34 [ 0.094751] iommu: Adding device 70015000.cec to group 35 [ 0.094783] iommu: Adding device 700e2000.thermal-sensor to group 36 [ 0.094815] iommu: Adding device 70110000.clock to group 37 [ 0.094847] iommu: Adding device 70300000.ahub to group 38 [ 0.094878] iommu: Adding device 7d000000.usb to group 39 [ 0.094910] iommu: Adding device 7d000000.usb-phy to group 40 [ 0.094949] iommu: Adding device 7d004000.usb to group 41 [ 0.094981] iommu: Adding device 7d004000.usb-phy to group 42 [ 0.095012] iommu: Adding device 7d008000.usb to group 43 [ 0.095044] iommu: Adding device 7d008000.usb-phy to group 44 [ 0.095075] iommu: Adding device pmu to group 45 [ 0.095106] iommu: Adding device timer to group 46 [ 0.095137] iommu: Adding device clocks to group 47 [ 0.095169] iommu: Adding device gpio-keys to group 48 [ 0.095204] iommu: Adding device regulators to group 49 [ 0.095236] iommu: Adding device regulators:regulator@0 to group 50 [ 0.095272] iommu: Adding device regulators:regulator@1 to group 51 [ 0.095304] iommu: Adding device regulators:regulator@2 to group 52 [ 0.095335] iommu: Adding device regulators:regulator@3 to group 53 [ 0.095367] iommu: Adding device regulators:regulator@4 to group 54 [ 0.095399] iommu: Adding device regulators:regulator@7 to group 55 [ 0.095431] iommu: Adding device regulators:regulator@8 to group 56 [ 0.095492] iommu: Adding device regulators:regulator@10 to group 57 [ 0.095528] iommu: Adding device regulators:regulator@11 to group 58 [ 0.095560] iommu: Adding device regulators:regulator@12 to group 59 [ 0.095591] iommu: Adding device regulators:regulator@13 to group 60 [ 0.095623] iommu: Adding device regulators:regulator@14 to group 61 [ 0.095660] iommu: Adding device sound to group 62 [ 0.110589] AT91: Could not find identification node [ 0.111148] +5V_SYS: supplied by +VDD_MUX [ 0.111437] +3.3V_SYS: supplied by +VDD_MUX [ 0.112045] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.112061] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.112161] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.112175] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.112359] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.112373] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.112470] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.112484] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.112580] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.112593] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.112691] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.112704] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.115752] vgaarb: loaded [ 0.116487] SCSI subsystem initialized [ 0.116666] libata version 3.00 loaded. [ 0.116859] usbcore: registered new interface driver usbfs [ 0.116912] usbcore: registered new interface driver hub [ 0.116974] usbcore: registered new device driver usb [ 0.120443] pps_core: LinuxPPS API ver. 1 registered [ 0.120454] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.120479] PTP clock support registered [ 0.120671] EDAC MC: Ver: 3.0.0 [ 0.123523] clocksource: Switched to clocksource arch_sys_counter [ 0.172813] NET: Registered protocol family 2 [ 0.173314] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.173415] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.173627] TCP: Hash tables configured (established 8192 bind 8192) [ 0.173715] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.173761] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.173910] NET: Registered protocol family 1 [ 0.174231] RPC: Registered named UNIX socket transport module. [ 0.174242] RPC: Registered udp transport module. [ 0.174251] RPC: Registered tcp transport module. [ 0.174260] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.174272] PCI: CLS 0 bytes, default 64 [ 0.175744] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.176489] iommu: Adding device alarmtimer to group 63 [ 0.177286] Initialise system trusted keyrings [ 0.177430] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.184000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.184582] NFS: Registering the id_resolver key type [ 0.184604] Key type id_resolver registered [ 0.184614] Key type id_legacy registered [ 0.184655] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.186158] Key type asymmetric registered [ 0.186170] Asymmetric key parser 'x509' registered [ 0.186222] bounce: pool size: 64 pages [ 0.186271] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.186282] io scheduler noop registered [ 0.186292] io scheduler deadline registered [ 0.186512] io scheduler cfq registered (default) [ 0.186523] io scheduler mq-deadline registered [ 0.186533] io scheduler kyber registered [ 0.190557] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.190670] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.191134] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.210369] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.210430] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.216889] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.223956] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.227324] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.277610] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.277713] iommu: Adding device serial8250 to group 64 [ 0.280206] console [ttyS0] disabled [ 0.280246] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.553213] console [ttyS0] enabled [ 1.557630] SuperH (H)SCI(F) driver initialized [ 1.563276] msm_serial: driver initialized [ 1.567584] STMicroelectronics ASC driver initialized [ 1.573306] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.582580] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.613806] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.630648] brd: module loaded [ 1.639999] loop: module loaded [ 1.644344] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.652653] as3722 4-0040: AS3722 with revision 0x1 found [ 1.660005] iommu: Adding device as3722-pinctrl to group 65 [ 1.667203] iommu: Adding device as3722-regulator to group 66 [ 1.675886] as3722-sd2: supplied by +5V_SYS [ 1.680467] as3722-sd3: supplied by +5V_SYS [ 1.684890] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.691209] as3722-sd4: supplied by +5V_SYS [ 1.695811] as3722-sd5: supplied by +5V_SYS [ 1.701760] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.707802] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.713997] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.719850] as3722-ldo3: supplied by +3.3V_SYS [ 1.724358] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.732096] as3722-ldo4: supplied by +3.3V_SYS [ 1.736775] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.742948] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.747795] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.754718] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.760371] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.766570] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.777113] iommu: Adding device as3722-rtc to group 67 [ 1.782658] iommu: Adding device as3722-adc to group 68 [ 1.788215] iommu: Adding device as3722-power-off to group 69 [ 1.794279] iommu: Adding device as3722-wdt to group 70 [ 1.801362] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.823878] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.830848] iommu: Adding device Fixed MDIO bus.0 to group 71 [ 1.836964] libphy: Fixed MDIO Bus: probed [ 1.842005] CAN device driver interface [ 1.846800] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.853890] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.859713] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.865686] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.872636] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.882284] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.889730] usbcore: registered new interface driver pegasus [ 1.895438] usbcore: registered new interface driver asix [ 1.900858] usbcore: registered new interface driver ax88179_178a [ 1.906998] usbcore: registered new interface driver cdc_ether [ 1.912865] usbcore: registered new interface driver smsc75xx [ 1.918663] usbcore: registered new interface driver smsc95xx [ 1.924449] usbcore: registered new interface driver net1080 [ 1.930126] usbcore: registered new interface driver cdc_subset [ 1.936083] usbcore: registered new interface driver zaurus [ 1.941691] usbcore: registered new interface driver cdc_ncm [ 1.947601] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.953192] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.960688] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.967228] ehci-pci: EHCI PCI platform driver [ 1.971698] ehci-platform: EHCI generic platform driver [ 1.977148] ehci-orion: EHCI orion driver [ 1.981316] SPEAr-ehci: EHCI SPEAr driver [ 1.985482] ehci-st: EHCI STMicroelectronics driver [ 1.990494] ehci-exynos: EHCI EXYNOS driver [ 1.994851] ehci-atmel: EHCI Atmel driver [ 1.998998] tegra-ehci: Tegra EHCI driver [ 2.005852] tegra-ehci 7d004000.usb: EHCI Host Controller [ 2.011267] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 2.019014] tegra-ehci 7d004000.usb: irq 356, io mem 0x7d004000 [ 2.053545] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 2.060131] hub 1-0:1.0: USB hub found [ 2.063934] hub 1-0:1.0: 1 port detected [ 2.068418] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.074619] ohci-pci: OHCI PCI platform driver [ 2.079093] ohci-platform: OHCI generic platform driver [ 2.084534] SPEAr-ohci: OHCI SPEAr driver [ 2.088684] ohci-st: OHCI STMicroelectronics driver [ 2.093724] ohci-atmel: OHCI Atmel driver [ 2.098527] usbcore: registered new interface driver usb-storage [ 2.106333] iommu: Adding device ci_hdrc.0 to group 72 [ 2.118603] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 2.125495] as3722-rtc as3722-rtc: RTC interrupt 379 [ 2.133933] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 2.141102] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 2.147867] i2c /dev entries driver [ 2.158522] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 2.173817] iommu: Adding device cpufreq-tegra124 to group 73 [ 2.181981] sdhci: Secure Digital Host Controller Interface driver [ 2.188177] sdhci: Copyright(c) Pierre Ossman [ 2.194340] Synopsys Designware Multimedia Card Interface Driver [ 2.201896] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.208381] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.213269] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.234544] mmc0: Unknown controller version (3). You may experience problems. [ 2.241803] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.313545] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.323147] ledtrig-cpu: registered to indicate activity on CPUs [ 2.329497] usbcore: registered new interface driver usbhid [ 2.335082] usbhid: USB HID core driver [ 2.343136] NET: Registered protocol family 10 [ 2.348462] Segment Routing with IPv6 [ 2.352282] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.358744] NET: Registered protocol family 17 [ 2.363193] can: controller area network core (rev 20170425 abi 9) [ 2.369440] NET: Registered protocol family 29 [ 2.373897] can: raw protocol (rev 20170425) [ 2.378162] can: broadcast manager protocol (rev 20170425 t) [ 2.383833] can: netlink gateway (rev 20170425) max_hops=1 [ 2.389593] Key type dns_resolver registered [ 2.394385] ThumbEE CPU extension supported. [ 2.398655] Registering SWP/SWPB emulation handler [ 2.404039] Loading compiled-in X.509 certificates [ 2.421310] +3.3V_RUN: supplied by +3.3V_SYS [ 2.427047] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.431677] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.437847] +5V_USB_HS: supplied by +5V_SYS [ 2.443358] +3.3V_LP0: supplied by +3.3V_SYS [ 2.450122] +5V_HDMI_CON: supplied by +5V_SYS [ 2.454161] mmc0: new high speed MMC card at address 0001 [ 2.454646] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.455215] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.455428] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.464763] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (237:0) [ 2.467053] mmcblk0: p1 [ 2.486892] +5V_SATA: supplied by +5V_SYS [ 2.491406] +12V_SATA: supplied by +VDD_MUX [ 2.497072] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.503951] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.510921] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.518961] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.524669] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.534648] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.545457] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.556553] as3722-sd2: supplied by +5V_SYS [ 2.561056] as3722-sd3: supplied by +5V_SYS [ 2.565646] as3722-sd4: supplied by +5V_SYS [ 2.570125] as3722-sd5: supplied by +5V_SYS [ 2.576173] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.581627] as3722-ldo1: supplied by +3.3V_RUN [ 2.586423] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.591925] as3722-ldo3: supplied by +3.3V_SYS [ 2.597244] as3722-ldo4: supplied by +3.3V_SYS [ 2.601910] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.606890] as3722-ldo6: supplied by +3.3V_RUN [ 2.611558] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.616965] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.624027] as3722-ldo9: supplied by +5V_SYS [ 2.629593] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.636181] as3722-ldo10: supplied by +5V_SYS [ 2.641102] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.647947] as3722-ldo11: supplied by +3.3V_RUN [ 2.653251] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.663394] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.672471] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.683255] scsi host0: tegra-ahci [ 2.687843] scsi host1: tegra-ahci [ 2.691463] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.699509] ata2: DUMMY [ 2.705525] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.710940] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.718728] tegra-ehci 7d008000.usb: irq 357, io mem 0x7d008000 [ 2.753643] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.760380] hub 2-0:1.0: USB hub found [ 2.764236] hub 2-0:1.0: 1 port detected [ 2.770768] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.775721] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.787750] mmc1: Unknown controller version (3). You may experience problems. [ 2.795101] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.864088] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.872250] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.880220] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.889961] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.914149] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.922493] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.937236] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.943561] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.949748] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.956659] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.964018] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.969546] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.975607] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.985301] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.995034] pci 0000:00:01.0: enabling Extended Tags [ 3.000012] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.009809] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.019632] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.026295] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.027202] ata1: SATA link down (SStatus 0 SControl 300) [ 3.041726] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.047796] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.057495] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.067184] pci 0000:00:02.0: enabling Extended Tags [ 3.072148] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.081916] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.091698] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.098325] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.108340] PCI: bus0: Fast back to back transfers disabled [ 3.113959] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.121966] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.130165] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.136233] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.143258] PCI: bus1: Fast back to back transfers disabled [ 3.148847] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.155629] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.161656] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.167273] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.174096] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.181523] PCI: bus2: Fast back to back transfers disabled [ 3.187135] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.193806] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.200587] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.207387] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.215139] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.221231] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.228568] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.233555] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.240366] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.248157] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.255488] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.261581] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.266556] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.272647] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.279444] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.287225] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.294339] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.300668] pcieport 0000:00:01.0: Signaling PME with IRQ 395 [ 3.306589] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.313661] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.319959] pcieport 0000:00:02.0: Signaling PME with IRQ 396 [ 3.326038] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.331624] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.337508] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): not PCI Express [ 3.361008] mmc1: new high speed SDHC card at address aaaa [ 3.367228] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.375229] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0a77000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 22 [ 3.384833] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.397389] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.406377] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.413007] [drm] No driver support for vblank timestamp query. [ 3.425102] mmcblk1: p1 p2 p3 [ 3.543086] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.790080] Console: switching to colour frame buffer device 512x135 [ 3.888657] drm drm: fb0: frame buffer device [ 3.893184] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.900844] iommu: Adding device cpufreq-dt.0 to group 74 [ 3.906730] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.914072] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.923172] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.930389] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:02:28 UTC (946684948) [ 3.939336] +USB0_VBUS_SW: disabling [ 3.942911] +1.8V_RUN_CAM: disabling [ 3.946745] +2.8V_RUN_CAM: disabling [ 3.950514] +1.2V_RUN_CAM_FRONT: disabling [ 3.954879] +1.05V_RUN_CAM_REAR: disabling [ 3.959120] +3.3V_RUN_TOUCH: disabling [ 3.963025] +2.8V_RUN_CAM_AF: disabling [ 3.967076] +1.8V_RUN_VPP_FUSE: disabling [ 3.972137] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.020651] EXT4-fs (mmcblk0p1): recovery complete [ 4.026439] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.034590] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.044748] devtmpfs: mounted [ 4.048386] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#