U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################################### 3.3 MiB/s done Bytes transferred = 8159752 (7c8208 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.6 MiB/s done Bytes transferred = 67173 (10665 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7c8200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83013664 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.0-next-20170911-199739-ga31cc45 (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Sun Sep 10 20:36:28 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c158e5c0, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @eef82000 s39424 r8192 d22016 u69632 [ 0.000000] pcpu-alloc: s39424 r8192 d22016 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993360K/2096128K available (10240K kernel code, 1626K rwdata, 4508K rodata, 2048K init, 405K bss, 37232K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc1596910 (1627 kB) [ 0.000000] .bss : 0xc159fbc0 - 0xc160537c ( 406 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000043] Switching to timer-based delay loop, resolution 1000ns [ 0.005036] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005055] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005075] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005089] Switching to timer-based delay loop, resolution 83ns [ 0.005567] Console: colour dummy device 80x30 [ 0.005602] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005619] pid_max: default: 32768 minimum: 301 [ 0.005720] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005736] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006233] CPU: Testing write buffer coherency: ok [ 0.006489] /cpus/cpu@0 missing clock-frequency property [ 0.006533] /cpus/cpu@1 missing clock-frequency property [ 0.006577] /cpus/cpu@2 missing clock-frequency property [ 0.006622] /cpus/cpu@3 missing clock-frequency property [ 0.006636] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006936] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.008869] Hierarchical SRCU implementation. [ 0.010712] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011463] EFI services will not be available. [ 0.011611] smp: Bringing up secondary CPUs ... [ 0.012087] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015450] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025492] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035016] smp: Brought up 1 node, 4 CPUs [ 0.035037] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035046] CPU: All CPU(s) started in SVC mode. [ 0.036564] devtmpfs: initialized [ 0.051153] Built 1 zonelists, mobility grouping on. Total pages: 514724 [ 0.051512] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.051936] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.051956] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052140] pinctrl core: initialized pinctrl subsystem [ 0.053598] DMI not present or invalid. [ 0.053834] NET: Registered protocol family 16 [ 0.055821] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058257] cpuidle: using governor menu [ 0.083163] No ATAGs? [ 0.083293] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.083309] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.090491] Serial: AMBA PL011 UART driver [ 0.091675] iommu: Adding device reg-dummy to group 0 [ 0.091713] iommu: Adding device 1003000.pcie to group 1 [ 0.091794] iommu: Adding device 50000000.host1x to group 2 [ 0.091866] iommu: Adding device 54200000.dc to group 3 [ 0.091935] iommu: Adding device 54240000.dc to group 4 [ 0.091972] iommu: Adding device 54280000.hdmi to group 5 [ 0.092044] iommu: Adding device 57000000.gpu to group 6 [ 0.092076] iommu: Adding device 60005000.timer to group 7 [ 0.092107] iommu: Adding device 60007000.flow-controller to group 8 [ 0.092138] iommu: Adding device 6000c800.actmon to group 9 [ 0.092169] iommu: Adding device 6000d000.gpio to group 10 [ 0.092202] iommu: Adding device 60020000.dma to group 11 [ 0.092238] iommu: Adding device 70000800.apbmisc to group 12 [ 0.092273] iommu: Adding device 70000868.pinmux to group 13 [ 0.092305] iommu: Adding device 70006000.serial to group 14 [ 0.092337] iommu: Adding device 70006040.serial to group 15 [ 0.092368] iommu: Adding device 70006300.serial to group 16 [ 0.092399] iommu: Adding device 7000c000.i2c to group 17 [ 0.092430] iommu: Adding device 7000c400.i2c to group 18 [ 0.092460] iommu: Adding device 7000c500.i2c to group 19 [ 0.092492] iommu: Adding device 7000c700.i2c to group 20 [ 0.092522] iommu: Adding device 7000d000.i2c to group 21 [ 0.092561] iommu: Adding device 7000d400.spi to group 22 [ 0.092592] iommu: Adding device 7000da00.spi to group 23 [ 0.092622] iommu: Adding device 7000e000.rtc to group 24 [ 0.092652] iommu: Adding device 7000e400.pmc to group 25 [ 0.092683] iommu: Adding device 7000f800.fuse to group 26 [ 0.092714] iommu: Adding device 70019000.memory-controller to group 27 [ 0.092744] iommu: Adding device 7001b000.emc to group 28 [ 0.092775] iommu: Adding device 70027000.sata to group 29 [ 0.092809] iommu: Adding device 70030000.hda to group 30 [ 0.092841] iommu: Adding device 70090000.usb to group 31 [ 0.092872] iommu: Adding device 7009f000.padctl to group 32 [ 0.092908] iommu: Adding device 700b0400.sdhci to group 33 [ 0.092939] iommu: Adding device 700b0600.sdhci to group 34 [ 0.092970] iommu: Adding device 700e2000.thermal-sensor to group 35 [ 0.093001] iommu: Adding device 70110000.clock to group 36 [ 0.093036] iommu: Adding device 70300000.ahub to group 37 [ 0.093068] iommu: Adding device 7d000000.usb to group 38 [ 0.093104] iommu: Adding device 7d000000.usb-phy to group 39 [ 0.093135] iommu: Adding device 7d004000.usb to group 40 [ 0.093166] iommu: Adding device 7d004000.usb-phy to group 41 [ 0.093197] iommu: Adding device 7d008000.usb to group 42 [ 0.093229] iommu: Adding device 7d008000.usb-phy to group 43 [ 0.093264] iommu: Adding device pmu to group 44 [ 0.093294] iommu: Adding device timer to group 45 [ 0.093326] iommu: Adding device clocks to group 46 [ 0.093360] iommu: Adding device gpio-keys to group 47 [ 0.093392] iommu: Adding device regulators to group 48 [ 0.093424] iommu: Adding device regulators:regulator@0 to group 49 [ 0.093456] iommu: Adding device regulators:regulator@1 to group 50 [ 0.093488] iommu: Adding device regulators:regulator@2 to group 51 [ 0.093519] iommu: Adding device regulators:regulator@3 to group 52 [ 0.093550] iommu: Adding device regulators:regulator@4 to group 53 [ 0.093586] iommu: Adding device regulators:regulator@7 to group 54 [ 0.093621] iommu: Adding device regulators:regulator@8 to group 55 [ 0.093653] iommu: Adding device regulators:regulator@10 to group 56 [ 0.093685] iommu: Adding device regulators:regulator@11 to group 57 [ 0.093716] iommu: Adding device regulators:regulator@12 to group 58 [ 0.093747] iommu: Adding device regulators:regulator@13 to group 59 [ 0.093777] iommu: Adding device regulators:regulator@14 to group 60 [ 0.093808] iommu: Adding device sound to group 61 [ 0.108502] AT91: Could not find identification node [ 0.109066] +5V_SYS: supplied by +VDD_MUX [ 0.109344] +3.3V_SYS: supplied by +VDD_MUX [ 0.109960] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.109976] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.110075] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.110089] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.110274] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.110287] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.110383] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.110396] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.110492] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.110505] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.110601] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.110613] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.113551] vgaarb: loaded [ 0.114266] SCSI subsystem initialized [ 0.114428] libata version 3.00 loaded. [ 0.114619] usbcore: registered new interface driver usbfs [ 0.114666] usbcore: registered new interface driver hub [ 0.114724] usbcore: registered new device driver usb [ 0.118188] pps_core: LinuxPPS API ver. 1 registered [ 0.118199] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.118220] PTP clock support registered [ 0.118410] EDAC MC: Ver: 3.0.0 [ 0.118681] dmi: Firmware registration failed. [ 0.121250] clocksource: Switched to clocksource arch_sys_counter [ 0.175956] NET: Registered protocol family 2 [ 0.176449] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.176550] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.176737] TCP: Hash tables configured (established 8192 bind 8192) [ 0.176819] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.176863] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.177011] NET: Registered protocol family 1 [ 0.177328] RPC: Registered named UNIX socket transport module. [ 0.177340] RPC: Registered udp transport module. [ 0.177348] RPC: Registered tcp transport module. [ 0.177356] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.177369] PCI: CLS 0 bytes, default 64 [ 0.178823] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.179543] iommu: Adding device alarmtimer to group 62 [ 0.180438] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.186227] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.186788] NFS: Registering the id_resolver key type [ 0.186811] Key type id_resolver registered [ 0.186821] Key type id_legacy registered [ 0.186866] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.188298] bounce: pool size: 64 pages [ 0.188345] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.188357] io scheduler noop registered [ 0.188366] io scheduler deadline registered [ 0.188570] io scheduler cfq registered (default) [ 0.188580] io scheduler mq-deadline registered [ 0.188590] io scheduler kyber registered [ 0.192332] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.192439] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.192895] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.211542] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.211596] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.217656] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.224500] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.227536] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.276181] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.276275] iommu: Adding device serial8250 to group 63 [ 0.278759] console [ttyS0] disabled [ 0.278799] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.549967] console [ttyS0] enabled [ 1.554334] SuperH (H)SCI(F) driver initialized [ 1.559946] msm_serial: driver initialized [ 1.564255] STMicroelectronics ASC driver initialized [ 1.570181] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.579447] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.594369] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.611058] brd: module loaded [ 1.620011] loop: module loaded [ 1.624354] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.632669] as3722 4-0040: AS3722 with revision 0x1 found [ 1.639936] iommu: Adding device as3722-pinctrl to group 64 [ 1.647003] iommu: Adding device as3722-regulator to group 65 [ 1.655570] as3722-sd2: supplied by +5V_SYS [ 1.660150] as3722-sd3: supplied by +5V_SYS [ 1.664677] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.670990] as3722-sd4: supplied by +5V_SYS [ 1.675602] as3722-sd5: supplied by +5V_SYS [ 1.681559] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.687577] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.693772] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.699641] as3722-ldo3: supplied by +3.3V_SYS [ 1.704141] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.711881] as3722-ldo4: supplied by +3.3V_SYS [ 1.716533] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.722731] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.727572] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.734485] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.740137] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.746334] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.756907] iommu: Adding device as3722-rtc to group 66 [ 1.762479] iommu: Adding device as3722-adc to group 67 [ 1.767996] iommu: Adding device as3722-power-off to group 68 [ 1.774055] iommu: Adding device as3722-wdt to group 69 [ 1.781092] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.803487] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.810408] iommu: Adding device Fixed MDIO bus.0 to group 70 [ 1.816609] libphy: Fixed MDIO Bus: probed [ 1.821638] CAN device driver interface [ 1.826402] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.833466] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.839290] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.845264] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.852231] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.861611] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.869036] usbcore: registered new interface driver pegasus [ 1.874742] usbcore: registered new interface driver asix [ 1.880165] usbcore: registered new interface driver ax88179_178a [ 1.886292] usbcore: registered new interface driver cdc_ether [ 1.892178] usbcore: registered new interface driver smsc75xx [ 1.897957] usbcore: registered new interface driver smsc95xx [ 1.903735] usbcore: registered new interface driver net1080 [ 1.909413] usbcore: registered new interface driver cdc_subset [ 1.915372] usbcore: registered new interface driver zaurus [ 1.920985] usbcore: registered new interface driver cdc_ncm [ 1.926881] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.932498] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.939871] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.946404] ehci-pci: EHCI PCI platform driver [ 1.950874] ehci-platform: EHCI generic platform driver [ 1.956321] ehci-orion: EHCI orion driver [ 1.960491] SPEAr-ehci: EHCI SPEAr driver [ 1.964652] ehci-st: EHCI STMicroelectronics driver [ 1.969662] ehci-exynos: EHCI EXYNOS driver [ 1.974021] ehci-atmel: EHCI Atmel driver [ 1.978161] tegra-ehci: Tegra EHCI driver [ 1.985025] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.990437] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.998228] tegra-ehci 7d004000.usb: irq 355, io mem 0x7d004000 [ 2.031272] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 2.037867] hub 1-0:1.0: USB hub found [ 2.041669] hub 1-0:1.0: 1 port detected [ 2.046153] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.052371] ohci-pci: OHCI PCI platform driver [ 2.056850] ohci-platform: OHCI generic platform driver [ 2.062290] SPEAr-ohci: OHCI SPEAr driver [ 2.066439] ohci-st: OHCI STMicroelectronics driver [ 2.071469] ohci-atmel: OHCI Atmel driver [ 2.076255] usbcore: registered new interface driver usb-storage [ 2.083826] iommu: Adding device ci_hdrc.0 to group 71 [ 2.096044] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 2.102935] as3722-rtc as3722-rtc: RTC interrupt 378 [ 2.111338] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 2.118508] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 2.125260] i2c /dev entries driver [ 2.132671] IR NEC protocol handler initialized [ 2.137196] IR RC5(x/sz) protocol handler initialized [ 2.142259] IR RC6 protocol handler initialized [ 2.146783] IR JVC protocol handler initialized [ 2.151326] IR Sony protocol handler initialized [ 2.155937] IR SANYO protocol handler initialized [ 2.160633] IR Sharp protocol handler initialized [ 2.165346] IR MCE Keyboard/mouse protocol handler initialized [ 2.171173] IR XMP protocol handler initialized [ 2.178908] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 2.194076] iommu: Adding device cpufreq-tegra124 to group 72 [ 2.202168] sdhci: Secure Digital Host Controller Interface driver [ 2.208339] sdhci: Copyright(c) Pierre Ossman [ 2.214384] Synopsys Designware Multimedia Card Interface Driver [ 2.221768] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.228227] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.233139] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.254383] mmc0: Unknown controller version (3). You may experience problems. [ 2.261662] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.331275] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.340819] ledtrig-cpu: registered to indicate activity on CPUs [ 2.347128] usbcore: registered new interface driver usbhid [ 2.352713] usbhid: USB HID core driver [ 2.360612] NET: Registered protocol family 10 [ 2.365887] Segment Routing with IPv6 [ 2.369608] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.376050] NET: Registered protocol family 17 [ 2.380494] can: controller area network core (rev 20170425 abi 9) [ 2.386740] NET: Registered protocol family 29 [ 2.391179] can: raw protocol (rev 20170425) [ 2.395461] can: broadcast manager protocol (rev 20170425 t) [ 2.401117] can: netlink gateway (rev 20170425) max_hops=1 [ 2.406885] Key type dns_resolver registered [ 2.411673] ThumbEE CPU extension supported. [ 2.415943] Registering SWP/SWPB emulation handler [ 2.435292] +3.3V_RUN: supplied by +3.3V_SYS [ 2.440786] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.445503] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.451470] +5V_USB_HS: supplied by +5V_SYS [ 2.457303] +3.3V_LP0: supplied by +3.3V_SYS [ 2.464048] +5V_HDMI_CON: supplied by +5V_SYS [ 2.469081] +5V_SATA: supplied by +5V_SYS [ 2.473659] +12V_SATA: supplied by +VDD_MUX [ 2.479783] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.481765] mmc0: new high speed MMC card at address 0001 [ 2.482502] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.483086] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.483606] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.484150] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.488879] mmcblk0: p1 [ 2.516863] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.523918] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.531928] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.537563] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.547182] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.557709] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.568626] as3722-sd2: supplied by +5V_SYS [ 2.573191] as3722-sd3: supplied by +5V_SYS [ 2.577591] as3722-sd4: supplied by +5V_SYS [ 2.582121] as3722-sd5: supplied by +5V_SYS [ 2.587986] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.593790] as3722-ldo1: supplied by +3.3V_RUN [ 2.598556] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.604267] as3722-ldo3: supplied by +3.3V_SYS [ 2.609569] as3722-ldo4: supplied by +3.3V_SYS [ 2.614367] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.619233] as3722-ldo6: supplied by +3.3V_RUN [ 2.623928] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.629313] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.636440] as3722-ldo9: supplied by +5V_SYS [ 2.642030] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.648582] as3722-ldo10: supplied by +5V_SYS [ 2.653547] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.660347] as3722-ldo11: supplied by +3.3V_RUN [ 2.665687] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.675435] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.684522] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.694953] scsi host0: tegra-ahci [ 2.699358] scsi host1: tegra-ahci [ 2.703025] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.711018] ata2: DUMMY [ 2.716876] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.722338] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.730101] tegra-ehci 7d008000.usb: irq 356, io mem 0x7d008000 [ 2.761372] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.768311] hub 2-0:1.0: USB hub found [ 2.772165] hub 2-0:1.0: 1 port detected [ 2.778616] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.783570] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.795479] mmc1: Unknown controller version (3). You may experience problems. [ 2.802827] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.871805] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.879950] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.888834] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.897239] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.921427] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.929770] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.943523] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.949801] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.956025] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.962934] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.970249] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.975814] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.981885] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.991585] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.001316] pci 0000:00:01.0: enabling Extended Tags [ 3.006296] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.016093] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.025916] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.032578] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.042624] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.045047] ata1: SATA link down (SStatus 0 SControl 300) [ 3.054078] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.063775] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.073494] pci 0000:00:02.0: enabling Extended Tags [ 3.078461] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.088230] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.098013] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.104639] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.114666] PCI: bus0: Fast back to back transfers disabled [ 3.120244] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.128290] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.136527] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.142642] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.149626] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.170822] mmc1: new high speed SDHC card at address aaaa [ 3.177026] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.181814] PCI: bus1: Fast back to back transfers disabled [ 3.187412] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.194299] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.200355] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.206015] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.212866] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.220225] pci 0000:02:00.0: supports D1 D2 [ 3.224512] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.244748] mmcblk1: p1 p2 p3 [ 3.261411] PCI: bus2: Fast back to back transfers disabled [ 3.266990] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.273703] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.280502] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.287340] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.295118] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.301215] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.308560] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.313565] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.320364] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.328138] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.335500] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.341612] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.346573] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.352703] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.359487] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.367273] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.374409] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.380739] pcieport 0000:00:01.0: Signaling PME with IRQ 394 [ 3.386640] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.393772] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.400103] pcieport 0000:00:02.0: Signaling PME with IRQ 395 [ 3.406214] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.411853] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.442841] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b81000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 396 [ 3.452513] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.464867] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.473236] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.479850] [drm] No driver support for vblank timestamp query. [ 3.613238] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.859838] Console: switching to colour frame buffer device 512x135 [ 3.958463] drm drm: fb0: frame buffer device [ 3.963003] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.970625] iommu: Adding device cpufreq-dt.0 to group 73 [ 3.976405] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.983735] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.992961] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 4.000253] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:02:12 UTC (946684932) [ 4.009238] +USB0_VBUS_SW: disabling [ 4.012861] +1.8V_RUN_CAM: disabling [ 4.016674] +2.8V_RUN_CAM: disabling [ 4.020399] +1.2V_RUN_CAM_FRONT: disabling [ 4.024731] +1.05V_RUN_CAM_REAR: disabling [ 4.028976] +3.3V_RUN_TOUCH: disabling [ 4.032944] +2.8V_RUN_CAM_AF: disabling [ 4.036975] +1.8V_RUN_VPP_FUSE: disabling [ 4.042232] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.089006] EXT4-fs (mmcblk0p1): recovery complete [ 4.094933] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.103065] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.111554] devtmpfs: mounted [ 4.115167] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#