U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################################### 3.8 MiB/s done Bytes transferred = 8159752 (7c8208 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.6 MiB/s done Bytes transferred = 67173 (10665 hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x7c8200 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83013664 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.0-next-20170905-199264-g744c56de (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04)) #1 SMP Tue Sep 5 05:18:29 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c158e580, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 17 pages/cpu @eef82000 s39424 r8192 d22016 u69632 [ 0.000000] pcpu-alloc: s39424 r8192 d22016 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993360K/2096128K available (10240K kernel code, 1626K rwdata, 4500K rodata, 2048K init, 405K bss, 37232K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc15968d0 (1627 kB) [ 0.000000] .bss : 0xc159fbc0 - 0xc16052fc ( 406 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000028] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000043] Switching to timer-based delay loop, resolution 1000ns [ 0.005147] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005167] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005186] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005200] Switching to timer-based delay loop, resolution 83ns [ 0.005678] Console: colour dummy device 80x30 [ 0.005712] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005731] pid_max: default: 32768 minimum: 301 [ 0.005832] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005847] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006342] CPU: Testing write buffer coherency: ok [ 0.006595] /cpus/cpu@0 missing clock-frequency property [ 0.006641] /cpus/cpu@1 missing clock-frequency property [ 0.006685] /cpus/cpu@2 missing clock-frequency property [ 0.006731] /cpus/cpu@3 missing clock-frequency property [ 0.006745] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007041] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.008998] Hierarchical SRCU implementation. [ 0.010867] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011624] EFI services will not be available. [ 0.011776] smp: Bringing up secondary CPUs ... [ 0.012252] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015557] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025599] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035127] smp: Brought up 1 node, 4 CPUs [ 0.035148] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035157] CPU: All CPU(s) started in SVC mode. [ 0.036676] devtmpfs: initialized [ 0.051545] Built 1 zonelists, mobility grouping on. Total pages: 514724 [ 0.051884] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.052310] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.052330] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.052506] pinctrl core: initialized pinctrl subsystem [ 0.053971] DMI not present or invalid. [ 0.054209] NET: Registered protocol family 16 [ 0.056169] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058621] cpuidle: using governor menu [ 0.083518] No ATAGs? [ 0.083647] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.083663] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.090931] Serial: AMBA PL011 UART driver [ 0.092115] iommu: Adding device reg-dummy to group 0 [ 0.092152] iommu: Adding device 1003000.pcie to group 1 [ 0.092234] iommu: Adding device 50000000.host1x to group 2 [ 0.092307] iommu: Adding device 54200000.dc to group 3 [ 0.092375] iommu: Adding device 54240000.dc to group 4 [ 0.092411] iommu: Adding device 54280000.hdmi to group 5 [ 0.092483] iommu: Adding device 57000000.gpu to group 6 [ 0.092516] iommu: Adding device 60005000.timer to group 7 [ 0.092548] iommu: Adding device 60007000.flow-controller to group 8 [ 0.092579] iommu: Adding device 6000c800.actmon to group 9 [ 0.092610] iommu: Adding device 6000d000.gpio to group 10 [ 0.092641] iommu: Adding device 60020000.dma to group 11 [ 0.092677] iommu: Adding device 70000800.apbmisc to group 12 [ 0.092711] iommu: Adding device 70000868.pinmux to group 13 [ 0.092742] iommu: Adding device 70006000.serial to group 14 [ 0.092773] iommu: Adding device 70006040.serial to group 15 [ 0.092804] iommu: Adding device 70006300.serial to group 16 [ 0.092834] iommu: Adding device 7000c000.i2c to group 17 [ 0.092864] iommu: Adding device 7000c400.i2c to group 18 [ 0.092894] iommu: Adding device 7000c500.i2c to group 19 [ 0.092926] iommu: Adding device 7000c700.i2c to group 20 [ 0.092957] iommu: Adding device 7000d000.i2c to group 21 [ 0.092996] iommu: Adding device 7000d400.spi to group 22 [ 0.093027] iommu: Adding device 7000da00.spi to group 23 [ 0.093056] iommu: Adding device 7000e000.rtc to group 24 [ 0.093086] iommu: Adding device 7000e400.pmc to group 25 [ 0.093117] iommu: Adding device 7000f800.fuse to group 26 [ 0.093148] iommu: Adding device 70019000.memory-controller to group 27 [ 0.093178] iommu: Adding device 7001b000.emc to group 28 [ 0.093208] iommu: Adding device 70027000.sata to group 29 [ 0.093243] iommu: Adding device 70030000.hda to group 30 [ 0.093275] iommu: Adding device 70090000.usb to group 31 [ 0.093306] iommu: Adding device 7009f000.padctl to group 32 [ 0.093343] iommu: Adding device 700b0400.sdhci to group 33 [ 0.093374] iommu: Adding device 700b0600.sdhci to group 34 [ 0.093405] iommu: Adding device 700e2000.thermal-sensor to group 35 [ 0.093436] iommu: Adding device 70110000.clock to group 36 [ 0.093470] iommu: Adding device 70300000.ahub to group 37 [ 0.093501] iommu: Adding device 7d000000.usb to group 38 [ 0.093536] iommu: Adding device 7d000000.usb-phy to group 39 [ 0.093567] iommu: Adding device 7d004000.usb to group 40 [ 0.093598] iommu: Adding device 7d004000.usb-phy to group 41 [ 0.093628] iommu: Adding device 7d008000.usb to group 42 [ 0.093659] iommu: Adding device 7d008000.usb-phy to group 43 [ 0.093694] iommu: Adding device pmu to group 44 [ 0.093725] iommu: Adding device timer to group 45 [ 0.093756] iommu: Adding device clocks to group 46 [ 0.093790] iommu: Adding device gpio-keys to group 47 [ 0.093821] iommu: Adding device regulators to group 48 [ 0.093852] iommu: Adding device regulators:regulator@0 to group 49 [ 0.093882] iommu: Adding device regulators:regulator@1 to group 50 [ 0.093914] iommu: Adding device regulators:regulator@2 to group 51 [ 0.093945] iommu: Adding device regulators:regulator@3 to group 52 [ 0.093975] iommu: Adding device regulators:regulator@4 to group 53 [ 0.094010] iommu: Adding device regulators:regulator@7 to group 54 [ 0.094045] iommu: Adding device regulators:regulator@8 to group 55 [ 0.094077] iommu: Adding device regulators:regulator@10 to group 56 [ 0.094107] iommu: Adding device regulators:regulator@11 to group 57 [ 0.094139] iommu: Adding device regulators:regulator@12 to group 58 [ 0.094170] iommu: Adding device regulators:regulator@13 to group 59 [ 0.094201] iommu: Adding device regulators:regulator@14 to group 60 [ 0.094231] iommu: Adding device sound to group 61 [ 0.108836] AT91: Could not find identification node [ 0.109405] +5V_SYS: supplied by +VDD_MUX [ 0.109686] +3.3V_SYS: supplied by +VDD_MUX [ 0.110319] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.110336] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.110438] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.110452] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.110645] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.110659] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.110759] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.110773] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.110874] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.110887] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.110988] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.111001] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.113953] vgaarb: loaded [ 0.114677] SCSI subsystem initialized [ 0.114846] libata version 3.00 loaded. [ 0.115037] usbcore: registered new interface driver usbfs [ 0.115085] usbcore: registered new interface driver hub [ 0.115144] usbcore: registered new device driver usb [ 0.118616] pps_core: LinuxPPS API ver. 1 registered [ 0.118627] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.118649] PTP clock support registered [ 0.118838] EDAC MC: Ver: 3.0.0 [ 0.119108] dmi: Firmware registration failed. [ 0.121680] clocksource: Switched to clocksource arch_sys_counter [ 0.176808] NET: Registered protocol family 2 [ 0.177300] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.177400] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.177588] TCP: Hash tables configured (established 8192 bind 8192) [ 0.177669] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.177714] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.177866] NET: Registered protocol family 1 [ 0.178179] RPC: Registered named UNIX socket transport module. [ 0.178190] RPC: Registered udp transport module. [ 0.178198] RPC: Registered tcp transport module. [ 0.178207] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.178220] PCI: CLS 0 bytes, default 64 [ 0.179696] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.180425] iommu: Adding device alarmtimer to group 62 [ 0.181325] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.187143] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.187705] NFS: Registering the id_resolver key type [ 0.187730] Key type id_resolver registered [ 0.187740] Key type id_legacy registered [ 0.187786] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.189217] bounce: pool size: 64 pages [ 0.189266] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.189278] io scheduler noop registered [ 0.189287] io scheduler deadline registered [ 0.189499] io scheduler cfq registered (default) [ 0.189509] io scheduler mq-deadline registered [ 0.189518] io scheduler kyber registered [ 0.193285] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.193393] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.193850] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.212787] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 0.212843] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 0.218955] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.225793] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.228715] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.276425] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.276522] iommu: Adding device serial8250 to group 63 [ 0.279001] console [ttyS0] disabled [ 0.279043] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.550437] console [ttyS0] enabled [ 1.554818] SuperH (H)SCI(F) driver initialized [ 1.560439] msm_serial: driver initialized [ 1.564742] STMicroelectronics ASC driver initialized [ 1.570673] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.579945] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.594887] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.611573] brd: module loaded [ 1.620525] loop: module loaded [ 1.624865] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.633190] as3722 4-0040: AS3722 with revision 0x1 found [ 1.640442] iommu: Adding device as3722-pinctrl to group 64 [ 1.647512] iommu: Adding device as3722-regulator to group 65 [ 1.656114] as3722-sd2: supplied by +5V_SYS [ 1.660693] as3722-sd3: supplied by +5V_SYS [ 1.665213] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.671522] as3722-sd4: supplied by +5V_SYS [ 1.676127] as3722-sd5: supplied by +5V_SYS [ 1.682076] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.688071] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.694269] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.700139] as3722-ldo3: supplied by +3.3V_SYS [ 1.704638] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.712379] as3722-ldo4: supplied by +3.3V_SYS [ 1.717031] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.723229] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.728071] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.734980] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.740633] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.746830] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.757433] iommu: Adding device as3722-rtc to group 66 [ 1.763007] iommu: Adding device as3722-adc to group 67 [ 1.768527] iommu: Adding device as3722-power-off to group 68 [ 1.774587] iommu: Adding device as3722-wdt to group 69 [ 1.781638] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.804010] m25p80 spi1.0: w25q32dw (4096 Kbytes) [ 1.810928] iommu: Adding device Fixed MDIO bus.0 to group 70 [ 1.817123] libphy: Fixed MDIO Bus: probed [ 1.822154] CAN device driver interface [ 1.826925] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.834002] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.839825] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.845796] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.852764] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.862186] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.869610] usbcore: registered new interface driver pegasus [ 1.875318] usbcore: registered new interface driver asix [ 1.880741] usbcore: registered new interface driver ax88179_178a [ 1.886869] usbcore: registered new interface driver cdc_ether [ 1.892758] usbcore: registered new interface driver smsc75xx [ 1.898537] usbcore: registered new interface driver smsc95xx [ 1.904317] usbcore: registered new interface driver net1080 [ 1.909994] usbcore: registered new interface driver cdc_subset [ 1.915954] usbcore: registered new interface driver zaurus [ 1.921566] usbcore: registered new interface driver cdc_ncm [ 1.927462] tegra-phy 7d000000.usb-phy: no vbus regulator [ 1.933077] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.940473] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.947010] ehci-pci: EHCI PCI platform driver [ 1.951480] ehci-platform: EHCI generic platform driver [ 1.956933] ehci-orion: EHCI orion driver [ 1.961103] SPEAr-ehci: EHCI SPEAr driver [ 1.965265] ehci-st: EHCI STMicroelectronics driver [ 1.970275] ehci-exynos: EHCI EXYNOS driver [ 1.974636] ehci-atmel: EHCI Atmel driver [ 1.978777] tegra-ehci: Tegra EHCI driver [ 1.985640] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.991053] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.998844] tegra-ehci 7d004000.usb: irq 355, io mem 0x7d004000 [ 2.031703] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 2.038292] hub 1-0:1.0: USB hub found [ 2.042096] hub 1-0:1.0: 1 port detected [ 2.046580] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.052799] ohci-pci: OHCI PCI platform driver [ 2.057280] ohci-platform: OHCI generic platform driver [ 2.062721] SPEAr-ohci: OHCI SPEAr driver [ 2.066870] ohci-st: OHCI STMicroelectronics driver [ 2.071898] ohci-atmel: OHCI Atmel driver [ 2.076682] usbcore: registered new interface driver usb-storage [ 2.084266] iommu: Adding device ci_hdrc.0 to group 71 [ 2.096488] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 2.103379] as3722-rtc as3722-rtc: RTC interrupt 378 [ 2.111804] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 2.118974] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 2.125726] i2c /dev entries driver [ 2.133131] IR NEC protocol handler initialized [ 2.137656] IR RC5(x/sz) protocol handler initialized [ 2.142723] IR RC6 protocol handler initialized [ 2.147246] IR JVC protocol handler initialized [ 2.151787] IR Sony protocol handler initialized [ 2.156397] IR SANYO protocol handler initialized [ 2.161093] IR Sharp protocol handler initialized [ 2.165806] IR MCE Keyboard/mouse protocol handler initialized [ 2.171630] IR XMP protocol handler initialized [ 2.179358] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 2.194501] iommu: Adding device cpufreq-tegra124 to group 72 [ 2.202606] sdhci: Secure Digital Host Controller Interface driver [ 2.208779] sdhci: Copyright(c) Pierre Ossman [ 2.214838] Synopsys Designware Multimedia Card Interface Driver [ 2.222238] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.228698] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.233609] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.254850] mmc0: Unknown controller version (3). You may experience problems. [ 2.262126] mmc0: Invalid maximum block size, assuming 512 bytes [ 2.331704] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 2.341257] ledtrig-cpu: registered to indicate activity on CPUs [ 2.347563] usbcore: registered new interface driver usbhid [ 2.353148] usbhid: USB HID core driver [ 2.360915] NET: Registered protocol family 10 [ 2.366191] Segment Routing with IPv6 [ 2.369912] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.376351] NET: Registered protocol family 17 [ 2.380797] can: controller area network core (rev 20170425 abi 9) [ 2.387042] NET: Registered protocol family 29 [ 2.391481] can: raw protocol (rev 20170425) [ 2.395765] can: broadcast manager protocol (rev 20170425 t) [ 2.401422] can: netlink gateway (rev 20170425) max_hops=1 [ 2.407194] Key type dns_resolver registered [ 2.411990] ThumbEE CPU extension supported. [ 2.416260] Registering SWP/SWPB emulation handler [ 2.435791] +3.3V_RUN: supplied by +3.3V_SYS [ 2.441290] +USB0_VBUS_SW: supplied by +5V_SYS [ 2.446010] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 2.451979] +5V_USB_HS: supplied by +5V_SYS [ 2.457818] +3.3V_LP0: supplied by +3.3V_SYS [ 2.464527] +5V_HDMI_CON: supplied by +5V_SYS [ 2.469558] +5V_SATA: supplied by +5V_SYS [ 2.474140] +12V_SATA: supplied by +VDD_MUX [ 2.480255] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.482604] mmc0: new high speed MMC card at address 0001 [ 2.483087] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.483579] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.484111] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.484780] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.489394] mmcblk0: p1 [ 2.517332] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.524390] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.532397] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.538032] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 [ 2.547696] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.558273] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.569197] as3722-sd2: supplied by +5V_SYS [ 2.573761] as3722-sd3: supplied by +5V_SYS [ 2.578160] as3722-sd4: supplied by +5V_SYS [ 2.582696] as3722-sd5: supplied by +5V_SYS [ 2.588557] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.594362] as3722-ldo1: supplied by +3.3V_RUN [ 2.599134] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.604853] as3722-ldo3: supplied by +3.3V_SYS [ 2.610150] as3722-ldo4: supplied by +3.3V_SYS [ 2.614949] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.619813] as3722-ldo6: supplied by +3.3V_RUN [ 2.624506] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.629891] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.637020] as3722-ldo9: supplied by +5V_SYS [ 2.642620] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.649172] as3722-ldo10: supplied by +5V_SYS [ 2.654143] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.660938] as3722-ldo11: supplied by +3.3V_RUN [ 2.666281] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.676034] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.685121] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.695552] scsi host0: tegra-ahci [ 2.699948] scsi host1: tegra-ahci [ 2.703612] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.711606] ata2: DUMMY [ 2.717473] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.722935] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.730696] tegra-ehci 7d008000.usb: irq 356, io mem 0x7d008000 [ 2.761804] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.768746] hub 2-0:1.0: USB hub found [ 2.772600] hub 2-0:1.0: 1 port detected [ 2.779060] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.784011] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.795910] mmc1: Unknown controller version (3). You may experience problems. [ 2.803258] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.872237] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.880385] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration [ 2.889267] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes [ 2.897675] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 [ 2.921837] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 2.930178] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 [ 2.943955] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.950235] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.956460] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.963370] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.970685] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.976250] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.982321] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.992022] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.001757] pci 0000:00:01.0: enabling Extended Tags [ 3.006739] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.016538] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.026367] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.033027] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.043080] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 3.045487] ata1: SATA link down (SStatus 0 SControl 300) [ 3.054538] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.064238] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.073958] pci 0000:00:02.0: enabling Extended Tags [ 3.078926] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 3.088695] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 3.098478] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.105105] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 3.115132] PCI: bus0: Fast back to back transfers disabled [ 3.120710] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.128757] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.136993] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.143111] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.150092] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.170934] mmc1: new high speed SDHC card at address aaaa [ 3.177139] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 3.181936] PCI: bus1: Fast back to back transfers disabled [ 3.187537] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.194403] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 3.200451] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 3.206080] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 3.212897] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 3.220248] pci 0000:02:00.0: supports D1 D2 [ 3.224532] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.244663] mmcblk1: p1 p2 p3 [ 3.251797] PCI: bus2: Fast back to back transfers disabled [ 3.257384] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.264084] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 3.270868] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 3.277697] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 3.285455] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 3.291550] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 3.298921] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.303908] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 3.310704] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 3.318504] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 3.325845] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 3.331956] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.336924] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 3.343052] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 3.349836] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 3.357644] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.364762] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 3.371089] pcieport 0000:00:01.0: Signaling PME with IRQ 394 [ 3.377038] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 3.384141] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 3.390463] pcieport 0000:00:02.0: Signaling PME with IRQ 395 [ 3.396652] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.402271] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 3.433301] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b81000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 396 [ 3.442993] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.455383] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 3.463771] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.470386] [drm] No driver support for vblank timestamp query. [ 3.604356] tegra-hdmi 54280000.hdmi: cannot set audio to 48000 Hz at 297000000 Hz pixel clock [ 3.851004] Console: switching to colour frame buffer device 512x135 [ 3.949602] drm drm: fb0: frame buffer device [ 3.954155] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 3.961812] iommu: Adding device cpufreq-dt.0 to group 73 [ 3.967578] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.974910] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.983988] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.991244] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:03:28 UTC (946685008) [ 4.000179] +USB0_VBUS_SW: disabling [ 4.003798] +1.8V_RUN_CAM: disabling [ 4.007569] +2.8V_RUN_CAM: disabling [ 4.011292] +1.2V_RUN_CAM_FRONT: disabling [ 4.015638] +1.05V_RUN_CAM_REAR: disabling [ 4.019885] +3.3V_RUN_TOUCH: disabling [ 4.023854] +2.8V_RUN_CAM_AF: disabling [ 4.027842] +1.8V_RUN_VPP_FUSE: disabling [ 4.033020] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 4.056177] EXT4-fs (mmcblk0p1): recovery complete [ 4.060987] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.069227] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.080563] devtmpfs: mounted [ 4.084877] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/# mount -t sysfs none /sys root@(none):/# root@(none):/# mount -t debugfs none /sys/kernel/debug root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:21 1970 [ 7.372738] PM: suspend entry (deep) [ 7.376314] PM: Syncing filesystems ... done. [ 7.450694] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 7.458813] OOM killer disabled. [ 7.462044] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 7.470713] Suspending console(s) (use no_console_suspend to debug)