U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 3.9 MiB/s done Bytes transferred = 7904480 (789ce0 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.6 MiB/s done Bytes transferred = 67133 (1063d hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x789ce0 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8301363c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.0-rc2-next-20170524-173950-g3433eca (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Tue May 23 20:35:19 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c157e800, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 17 pages/cpu @eef82000 s39232 r8192 d22208 u69632 [ 0.000000] pcpu-alloc: s39232 r8192 d22208 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993432K/2096128K available (10240K kernel code, 1561K rwdata, 4380K rodata, 2048K init, 401K bss, 37160K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc1586470 (1562 kB) [ 0.000000] .bss : 0xc158fcb0 - 0xc15f43d8 ( 402 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000029] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000044] Switching to timer-based delay loop, resolution 1000ns [ 0.005284] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.005303] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.005322] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.005336] Switching to timer-based delay loop, resolution 83ns [ 0.005800] Console: colour dummy device 80x30 [ 0.005829] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005848] pid_max: default: 32768 minimum: 301 [ 0.005941] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005956] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006440] CPU: Testing write buffer coherency: ok [ 0.006685] /cpus/cpu@0 missing clock-frequency property [ 0.006730] /cpus/cpu@1 missing clock-frequency property [ 0.006773] /cpus/cpu@2 missing clock-frequency property [ 0.006817] /cpus/cpu@3 missing clock-frequency property [ 0.006831] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.007115] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.009060] Hierarchical SRCU implementation. [ 0.010925] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011677] EFI services will not be available. [ 0.011903] smp: Bringing up secondary CPUs ... [ 0.012488] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015744] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025765] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035202] smp: Brought up 1 node, 4 CPUs [ 0.035224] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.035232] CPU: All CPU(s) started in SVC mode. [ 0.036713] devtmpfs: initialized [ 0.052835] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.053232] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.053251] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.054694] pinctrl core: initialized pinctrl subsystem [ 0.056629] NET: Registered protocol family 16 [ 0.058719] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.061201] cpuidle: using governor menu [ 0.087778] No ATAGs? [ 0.087905] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.087922] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.095123] Serial: AMBA PL011 UART driver [ 0.111925] AT91: Could not find identification node [ 0.112492] +5V_SYS: supplied by +VDD_MUX [ 0.112776] +3.3V_SYS: supplied by +VDD_MUX [ 0.113400] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.113417] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.113518] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.113533] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.113719] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.113733] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.113830] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.113843] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.113940] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.113954] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.114051] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.114064] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.117042] vgaarb: loaded [ 0.117821] SCSI subsystem initialized [ 0.117983] libata version 3.00 loaded. [ 0.118230] usbcore: registered new interface driver usbfs [ 0.118290] usbcore: registered new interface driver hub [ 0.118360] usbcore: registered new device driver usb [ 0.121824] pps_core: LinuxPPS API ver. 1 registered [ 0.121835] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.121859] PTP clock support registered [ 0.122049] EDAC MC: Ver: 3.0.0 [ 0.124929] clocksource: Switched to clocksource arch_sys_counter [ 0.179362] NET: Registered protocol family 2 [ 0.179870] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.179971] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.180158] TCP: Hash tables configured (established 8192 bind 8192) [ 0.180240] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.180286] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.180437] NET: Registered protocol family 1 [ 0.180753] RPC: Registered named UNIX socket transport module. [ 0.180764] RPC: Registered udp transport module. [ 0.180772] RPC: Registered tcp transport module. [ 0.180781] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.180793] PCI: CLS 0 bytes, default 64 [ 0.182207] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.183924] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.192324] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.193024] NFS: Registering the id_resolver key type [ 0.193049] Key type id_resolver registered [ 0.193058] Key type id_legacy registered [ 0.193099] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.194710] bounce: pool size: 64 pages [ 0.194753] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.194764] io scheduler noop registered [ 0.194774] io scheduler deadline registered [ 0.194803] io scheduler cfq registered (default) [ 0.194812] io scheduler mq-deadline registered [ 0.194821] io scheduler kyber registered [ 0.198221] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.198335] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.198787] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.216792] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 0.216848] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 0.223186] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.231021] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.233530] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.287731] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.290302] console [ttyS0] disabled [ 0.290341] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.185722] console [ttyS0] enabled [ 1.190025] SuperH (H)SCI(F) driver initialized [ 1.195549] msm_serial: driver initialized [ 1.199823] STMicroelectronics ASC driver initialized [ 1.205750] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.215026] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.229083] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.248577] brd: module loaded [ 1.258633] loop: module loaded [ 1.262967] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.271315] as3722 4-0040: AS3722 with revision 0x1 found [ 1.283182] as3722-sd2: supplied by +5V_SYS [ 1.287824] as3722-sd3: supplied by +5V_SYS [ 1.292209] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.298622] as3722-sd4: supplied by +5V_SYS [ 1.303228] as3722-sd5: supplied by +5V_SYS [ 1.309250] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.315300] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.321512] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.327414] as3722-ldo3: supplied by +3.3V_SYS [ 1.331889] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.339654] as3722-ldo4: supplied by +3.3V_SYS [ 1.344310] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.350523] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.355368] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.362261] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.367935] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.374113] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.387216] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.407449] random: fast init done [ 1.410976] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.418938] libphy: Fixed MDIO Bus: probed [ 1.424113] CAN device driver interface [ 1.428884] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.435920] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.441743] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.447726] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.454675] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.463886] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.471338] usbcore: registered new interface driver pegasus [ 1.477058] usbcore: registered new interface driver asix [ 1.482485] usbcore: registered new interface driver ax88179_178a [ 1.488622] usbcore: registered new interface driver cdc_ether [ 1.494497] usbcore: registered new interface driver smsc75xx [ 1.500310] usbcore: registered new interface driver smsc95xx [ 1.506102] usbcore: registered new interface driver net1080 [ 1.511788] usbcore: registered new interface driver cdc_subset [ 1.517752] usbcore: registered new interface driver zaurus [ 1.523372] usbcore: registered new interface driver cdc_ncm [ 1.529266] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.536690] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.543207] ehci-pci: EHCI PCI platform driver [ 1.547703] ehci-platform: EHCI generic platform driver [ 1.553130] ehci-orion: EHCI orion driver [ 1.557316] SPEAr-ehci: EHCI SPEAr driver [ 1.561463] ehci-st: EHCI STMicroelectronics driver [ 1.566493] ehci-exynos: EHCI EXYNOS driver [ 1.570828] ehci-atmel: EHCI Atmel driver [ 1.574986] tegra-ehci: Tegra EHCI driver [ 1.581823] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.587264] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.595013] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.624957] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.631635] hub 1-0:1.0: USB hub found [ 1.635437] hub 1-0:1.0: 1 port detected [ 1.639925] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.646127] ohci-pci: OHCI PCI platform driver [ 1.650606] ohci-platform: OHCI generic platform driver [ 1.656014] ohci-omap3: OHCI OMAP3 driver [ 1.660154] SPEAr-ohci: OHCI SPEAr driver [ 1.664297] ohci-st: OHCI STMicroelectronics driver [ 1.669321] ohci-atmel: OHCI Atmel driver [ 1.674083] usbcore: registered new interface driver usb-storage [ 1.684433] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.691331] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.699507] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.706689] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.713379] i2c /dev entries driver [ 1.723593] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.740891] sdhci: Secure Digital Host Controller Interface driver [ 1.747090] sdhci: Copyright(c) Pierre Ossman [ 1.753037] Synopsys Designware Multimedia Card Interface Driver [ 1.760367] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.766817] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.771707] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.792956] mmc0: Unknown controller version (3). You may experience problems. [ 1.800233] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.864953] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.874276] ledtrig-cpu: registered to indicate activity on CPUs [ 1.880680] usbcore: registered new interface driver usbhid [ 1.886264] usbhid: USB HID core driver [ 1.894124] NET: Registered protocol family 10 [ 1.899461] Segment Routing with IPv6 [ 1.903176] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.909665] NET: Registered protocol family 17 [ 1.914109] can: controller area network core (rev 20170425 abi 9) [ 1.920352] NET: Registered protocol family 29 [ 1.924792] can: raw protocol (rev 20170425) [ 1.929073] can: broadcast manager protocol (rev 20170425 t) [ 1.934728] can: netlink gateway (rev 20170425) max_hops=1 [ 1.940526] Key type dns_resolver registered [ 1.945345] ThumbEE CPU extension supported. [ 1.949614] Registering SWP/SWPB emulation handler [ 1.968389] +3.3V_RUN: supplied by +3.3V_SYS [ 1.973843] +USB0_VBUS_SW: supplied by +5V_SYS [ 1.978570] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.984480] +5V_USB_HS: supplied by +5V_SYS [ 1.990295] +3.3V_LP0: supplied by +3.3V_SYS [ 1.996305] +5V_HDMI_CON: supplied by +5V_SYS [ 2.001326] +5V_SATA: supplied by +5V_SYS [ 2.005874] +12V_SATA: supplied by +VDD_MUX [ 2.011865] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.012491] mmc0: new high speed MMC card at address 0001 [ 2.013500] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.014246] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.014531] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.014869] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.021294] mmcblk0: p1 [ 2.048981] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.056041] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.063919] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.070575] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 2.081705] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.093058] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.103404] as3722-sd2: supplied by +5V_SYS [ 2.107961] as3722-sd3: supplied by +5V_SYS [ 2.112379] as3722-sd4: supplied by +5V_SYS [ 2.116923] as3722-sd5: supplied by +5V_SYS [ 2.122808] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.128610] as3722-ldo1: supplied by +3.3V_RUN [ 2.133379] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.139097] as3722-ldo3: supplied by +3.3V_SYS [ 2.144399] as3722-ldo4: supplied by +3.3V_SYS [ 2.149218] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.154099] as3722-ldo6: supplied by +3.3V_RUN [ 2.158813] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.164186] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.171331] as3722-ldo9: supplied by +5V_SYS [ 2.176909] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.183630] as3722-ldo10: supplied by +5V_SYS [ 2.188799] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.195645] as3722-ldo11: supplied by +3.3V_RUN [ 2.200932] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.210671] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.219748] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.230150] scsi host0: tegra-ahci [ 2.234681] scsi host1: tegra-ahci [ 2.238449] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.246491] ata2: DUMMY [ 2.252282] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.257738] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.265486] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.295051] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.302092] hub 2-0:1.0: USB hub found [ 2.305948] hub 2-0:1.0: 1 port detected [ 2.312306] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.317261] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.329153] mmc1: Unknown controller version (3). You may experience problems. [ 2.336495] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.405474] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.413579] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.422247] tegra-pcie 1003000.pcie-controller: probing port 0, using 2 lanes [ 2.432929] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000008 [ 2.455772] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 2.465043] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000000 [ 2.479348] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.486627] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.492814] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.499723] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.507083] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.512611] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.518716] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.528522] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.538330] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.544998] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.555033] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.561099] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.570896] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.576653] ata1: SATA link down (SStatus 0 SControl 300) [ 2.586112] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.592737] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.602742] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.612493] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.622238] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.631895] pci_bus 0000:00: 1-byte config write to 0000:00:01.0 offset 0xc may corrupt adjacent RW1C bits [ 2.641555] PCI: bus0: Fast back to back transfers disabled [ 2.647140] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.655167] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.663398] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.669491] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.676479] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.697604] mmc1: new high speed SDHC card at address aaaa [ 2.704105] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.708917] PCI: bus1: Fast back to back transfers disabled [ 2.714515] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.721391] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.727486] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.733100] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.739951] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.747352] pci 0000:02:00.0: supports D1 D2 [ 2.751623] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.772178] mmcblk1: p1 p2 p3 [ 2.785101] PCI: bus2: Fast back to back transfers disabled [ 2.790690] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.797504] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.804288] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.811114] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.818869] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.824980] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.832322] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.837327] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.844122] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.851919] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.859258] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.865393] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.870357] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.876465] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.883247] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.891052] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.898135] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.904477] pcieport 0000:00:01.0: Signaling PME with IRQ 393 [ 2.910375] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.917444] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.923767] pcieport 0000:00:02.0: Signaling PME with IRQ 394 [ 2.929873] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.935486] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.966653] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b72000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 2.976344] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.989149] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.997113] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 3.005209] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.012523] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.021671] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.029057] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:01:36 UTC (946684896) [ 3.037979] +3.3V_AVDD_HDMI_AP_GATED: disabling [ 3.042501] +USB0_VBUS_SW: disabling [ 3.046096] +1.05V_RUN_AVDD_HDMI_PLL: disabling [ 3.050623] +5V_HDMI_CON: disabling [ 3.054110] +1.8V_RUN_CAM: disabling [ 3.057924] +2.8V_RUN_CAM: disabling [ 3.061690] +1.2V_RUN_CAM_FRONT: disabling [ 3.066046] +1.05V_RUN_CAM_REAR: disabling [ 3.070294] +3.3V_RUN_TOUCH: disabling [ 3.074193] +2.8V_RUN_CAM_AF: disabling [ 3.078239] +1.8V_RUN_VPP_FUSE: disabling [ 3.083055] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.125773] EXT4-fs (mmcblk0p1): recovery complete [ 3.131573] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.139698] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.149435] devtmpfs: mounted [ 3.153225] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#