U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 4 MiB/s done Bytes transferred = 7917696 (78d080 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.8 MiB/s done Bytes transferred = 67133 (1063d hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x78d080 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8301363c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.0-next-20170502-170647-gb211a48 (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Fri May 5 03:02:52 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c157f880, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 17 pages/cpu @eef82000 s39488 r8192 d21952 u69632 [ 0.000000] pcpu-alloc: s39488 r8192 d21952 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993420K/2096128K available (10240K kernel code, 1565K rwdata, 4388K rodata, 2048K init, 411K bss, 37172K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc15874f0 (1566 kB) [ 0.000000] .bss : 0xc1590d10 - 0xc15f7b58 ( 412 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000029] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000045] Switching to timer-based delay loop, resolution 1000ns [ 0.004877] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.004896] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.004915] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.004929] Switching to timer-based delay loop, resolution 83ns [ 0.005401] Console: colour dummy device 80x30 [ 0.005431] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005449] pid_max: default: 32768 minimum: 301 [ 0.005537] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005553] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006030] CPU: Testing write buffer coherency: ok [ 0.006278] /cpus/cpu@0 missing clock-frequency property [ 0.006321] /cpus/cpu@1 missing clock-frequency property [ 0.006362] /cpus/cpu@2 missing clock-frequency property [ 0.006405] /cpus/cpu@3 missing clock-frequency property [ 0.006418] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006704] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.008596] Hierarchical SRCU implementation. [ 0.010396] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011117] EFI services will not be available. [ 0.011344] smp: Bringing up secondary CPUs ... [ 0.011946] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015353] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025384] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.034796] smp: Brought up 1 node, 4 CPUs [ 0.034818] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.034826] CPU: All CPU(s) started in SVC mode. [ 0.036314] devtmpfs: initialized [ 0.052627] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.053024] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.053043] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.054535] pinctrl core: initialized pinctrl subsystem [ 0.056444] NET: Registered protocol family 16 [ 0.058538] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.060928] cpuidle: using governor menu [ 0.087452] No ATAGs? [ 0.087578] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.087593] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.094843] Serial: AMBA PL011 UART driver [ 0.111086] AT91: Could not find identification node [ 0.111641] +5V_SYS: supplied by +VDD_MUX [ 0.111928] +3.3V_SYS: supplied by +VDD_MUX [ 0.112556] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.112573] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.112674] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.112689] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.112878] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.112892] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.112991] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.113005] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.113103] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.113117] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.113214] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.113228] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.116183] vgaarb: loaded [ 0.116991] SCSI subsystem initialized [ 0.117160] libata version 3.00 loaded. [ 0.117404] usbcore: registered new interface driver usbfs [ 0.117465] usbcore: registered new interface driver hub [ 0.117525] usbcore: registered new device driver usb [ 0.120983] pps_core: LinuxPPS API ver. 1 registered [ 0.120995] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.121019] PTP clock support registered [ 0.121208] EDAC MC: Ver: 3.0.0 [ 0.124064] clocksource: Switched to clocksource arch_sys_counter [ 0.179274] NET: Registered protocol family 2 [ 0.179781] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.179883] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.180070] TCP: Hash tables configured (established 8192 bind 8192) [ 0.180151] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.180195] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.180345] NET: Registered protocol family 1 [ 0.180651] RPC: Registered named UNIX socket transport module. [ 0.180662] RPC: Registered udp transport module. [ 0.180671] RPC: Registered tcp transport module. [ 0.180679] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.180692] PCI: CLS 0 bytes, default 64 [ 0.182125] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.183952] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.192433] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.193136] NFS: Registering the id_resolver key type [ 0.193171] Key type id_resolver registered [ 0.193181] Key type id_legacy registered [ 0.193225] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.194931] bounce: pool size: 64 pages [ 0.194971] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.194983] io scheduler noop registered [ 0.194993] io scheduler deadline registered [ 0.195021] io scheduler cfq registered (default) [ 0.195031] io scheduler mq-deadline registered [ 0.195041] io scheduler kyber registered [ 0.200461] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.200585] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.201044] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.216964] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 0.217018] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 0.223234] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.231054] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.233797] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.289597] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.292184] console [ttyS0] disabled [ 0.292223] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.187903] console [ttyS0] enabled [ 1.192221] SuperH (H)SCI(F) driver initialized [ 1.197753] msm_serial: driver initialized [ 1.202032] STMicroelectronics ASC driver initialized [ 1.207946] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.217218] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.231284] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.250337] brd: module loaded [ 1.260380] loop: module loaded [ 1.264714] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.273044] as3722 4-0040: AS3722 with revision 0x1 found [ 1.284855] as3722-sd2: supplied by +5V_SYS [ 1.289471] as3722-sd3: supplied by +5V_SYS [ 1.293860] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.300301] as3722-sd4: supplied by +5V_SYS [ 1.304933] as3722-sd5: supplied by +5V_SYS [ 1.310954] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.317022] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.323216] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.329110] as3722-ldo3: supplied by +3.3V_SYS [ 1.333586] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.341365] as3722-ldo4: supplied by +3.3V_SYS [ 1.346057] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.352238] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.357085] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.363985] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.369657] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.375850] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.388931] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.408770] random: fast init done [ 1.412341] m25p80 spi32765.0: w25q32dw (4096 Kbytes) [ 1.420166] libphy: Fixed MDIO Bus: probed [ 1.425338] CAN device driver interface [ 1.430091] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.437209] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.443033] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.449019] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.455987] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.465173] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.472606] usbcore: registered new interface driver pegasus [ 1.478330] usbcore: registered new interface driver asix [ 1.483756] usbcore: registered new interface driver ax88179_178a [ 1.489889] usbcore: registered new interface driver cdc_ether [ 1.495782] usbcore: registered new interface driver smsc75xx [ 1.501570] usbcore: registered new interface driver smsc95xx [ 1.507361] usbcore: registered new interface driver net1080 [ 1.513047] usbcore: registered new interface driver cdc_subset [ 1.519011] usbcore: registered new interface driver zaurus [ 1.524644] usbcore: registered new interface driver cdc_ncm [ 1.530520] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.537944] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.544480] ehci-pci: EHCI PCI platform driver [ 1.548959] ehci-platform: EHCI generic platform driver [ 1.554402] ehci-orion: EHCI orion driver [ 1.558564] SPEAr-ehci: EHCI SPEAr driver [ 1.562708] ehci-st: EHCI STMicroelectronics driver [ 1.567732] ehci-exynos: EHCI EXYNOS driver [ 1.572074] ehci-atmel: EHCI Atmel driver [ 1.576233] tegra-ehci: Tegra EHCI driver [ 1.583072] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.588507] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.596283] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.624092] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.630806] hub 1-0:1.0: USB hub found [ 1.634610] hub 1-0:1.0: 1 port detected [ 1.639061] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.645281] ohci-pci: OHCI PCI platform driver [ 1.649760] ohci-platform: OHCI generic platform driver [ 1.655166] ohci-omap3: OHCI OMAP3 driver [ 1.659305] SPEAr-ohci: OHCI SPEAr driver [ 1.663447] ohci-st: OHCI STMicroelectronics driver [ 1.668473] ohci-atmel: OHCI Atmel driver [ 1.673237] usbcore: registered new interface driver usb-storage [ 1.683706] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.690603] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.698831] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.706011] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.712700] i2c /dev entries driver [ 1.722895] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.740087] sdhci: Secure Digital Host Controller Interface driver [ 1.746285] sdhci: Copyright(c) Pierre Ossman [ 1.752228] Synopsys Designware Multimedia Card Interface Driver [ 1.759555] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.766000] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.770890] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.792160] mmc0: Unknown controller version (3). You may experience problems. [ 1.799432] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.864087] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.873387] ledtrig-cpu: registered to indicate activity on CPUs [ 1.879721] usbcore: registered new interface driver usbhid [ 1.885305] usbhid: USB HID core driver [ 1.893030] NET: Registered protocol family 10 [ 1.898337] Segment Routing with IPv6 [ 1.902048] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.908534] NET: Registered protocol family 17 [ 1.912978] can: controller area network core (rev 20170425 abi 9) [ 1.919220] NET: Registered protocol family 29 [ 1.923659] can: raw protocol (rev 20170425) [ 1.927941] can: broadcast manager protocol (rev 20170425 t) [ 1.933597] can: netlink gateway (rev 20170425) max_hops=1 [ 1.939387] Key type dns_resolver registered [ 1.944211] ThumbEE CPU extension supported. [ 1.948482] Registering SWP/SWPB emulation handler [ 1.967965] +3.3V_RUN: supplied by +3.3V_SYS [ 1.973520] +USB0_VBUS_SW: supplied by +5V_SYS [ 1.978263] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.984215] +5V_USB_HS: supplied by +5V_SYS [ 1.990043] +3.3V_LP0: supplied by +3.3V_SYS [ 1.996521] +5V_HDMI_CON: supplied by +5V_SYS [ 2.001551] +5V_SATA: supplied by +5V_SYS [ 2.006128] +12V_SATA: supplied by +VDD_MUX [ 2.012488] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.013811] mmc0: new high speed MMC card at address 0001 [ 2.019943] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.020702] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.021088] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.022244] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.037128] mmcblk0: p1 [ 2.049571] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.056673] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.064671] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.071257] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 2.082399] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.093728] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.105119] as3722-sd2: supplied by +5V_SYS [ 2.109587] as3722-sd3: supplied by +5V_SYS [ 2.114005] as3722-sd4: supplied by +5V_SYS [ 2.118603] as3722-sd5: supplied by +5V_SYS [ 2.124836] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.130560] as3722-ldo1: supplied by +3.3V_RUN [ 2.135380] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.140888] as3722-ldo3: supplied by +3.3V_SYS [ 2.146221] as3722-ldo4: supplied by +3.3V_SYS [ 2.150913] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.155914] as3722-ldo6: supplied by +3.3V_RUN [ 2.160608] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.166009] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.173081] as3722-ldo9: supplied by +5V_SYS [ 2.178681] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.185261] as3722-ldo10: supplied by +5V_SYS [ 2.190180] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.197037] as3722-ldo11: supplied by +3.3V_RUN [ 2.202338] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.212277] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.221352] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.231944] scsi host0: tegra-ahci [ 2.236557] scsi host1: tegra-ahci [ 2.240252] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.248291] ata2: DUMMY [ 2.254034] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.259490] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.267234] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.294185] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.301235] hub 2-0:1.0: USB hub found [ 2.305091] hub 2-0:1.0: 1 port detected [ 2.311432] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.316382] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.328289] mmc1: Unknown controller version (3). You may experience problems. [ 2.335628] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.404603] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.412703] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.422508] tegra-pcie 1003000.pcie-controller: probing port 0, using 2 lanes [ 2.431872] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000008 [ 2.454744] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 2.464036] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000000 [ 2.478556] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.485827] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.492015] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.498923] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.506275] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.511805] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.517903] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.527699] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.537521] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.544182] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.554231] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.560288] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.570084] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.577824] ata1: SATA link down (SStatus 0 SControl 300) [ 2.585301] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.591925] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.601956] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.611741] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.621522] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.631185] pci_bus 0000:00: 1-byte config write to 0000:00:01.0 offset 0xc may corrupt adjacent RW1C bits [ 2.640879] PCI: bus0: Fast back to back transfers disabled [ 2.646466] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.654485] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.662702] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.668771] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.675760] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.696879] mmc1: new high speed SDHC card at address aaaa [ 2.703151] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.707974] PCI: bus1: Fast back to back transfers disabled [ 2.713572] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.720438] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.726493] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.732090] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.738913] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.746338] pci 0000:02:00.0: supports D1 D2 [ 2.750612] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.770813] mmcblk1: p1 p2 p3 [ 2.784222] PCI: bus2: Fast back to back transfers disabled [ 2.789800] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.796643] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.803437] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.810272] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.818052] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.824169] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.831497] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.836502] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.843301] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.851077] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.858440] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.864555] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.869517] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.875647] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.882433] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.890218] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.897322] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.903659] pcieport 0000:00:01.0: Signaling PME with IRQ 393 [ 2.909523] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.916622] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.922950] pcieport 0000:00:02.0: Signaling PME with IRQ 394 [ 2.928997] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.934631] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.965788] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b72000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 2.975480] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.988322] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.996320] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 3.004413] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.011728] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.020870] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.028164] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:13 UTC (946684813) [ 3.037165] +3.3V_AVDD_HDMI_AP_GATED: disabling [ 3.041689] +USB0_VBUS_SW: disabling [ 3.045290] +1.05V_RUN_AVDD_HDMI_PLL: disabling [ 3.049820] +5V_HDMI_CON: disabling [ 3.053309] +1.8V_RUN_CAM: disabling [ 3.057177] +2.8V_RUN_CAM: disabling [ 3.060991] +1.2V_RUN_CAM_FRONT: disabling [ 3.065367] +1.05V_RUN_CAM_REAR: disabling [ 3.069626] +3.3V_RUN_TOUCH: disabling [ 3.073536] +2.8V_RUN_CAM_AF: disabling [ 3.077632] +1.8V_RUN_VPP_FUSE: disabling [ 3.082784] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.126386] EXT4-fs (mmcblk0p1): recovery complete [ 3.131977] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.140127] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.150333] devtmpfs: mounted [ 3.154261] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#