[0000.773] [TegraBoot] (version 23.00.2015.14-mobile-1ef66670) [0000.778] Processing in cold boot mode Bootloader 2 [0000.783] A01Q Bootrom Patch rev = 3 [0000.786] Power-up reason: pmu watchdog [0000.790] No Battery Present [0000.793] Platform has Ddr4 type ram [0000.796] max77620 disabling SD1 Remote Sense [0000.800] Setting Ddr voltage to 1125mv [0000.805] Serial Number of Pmic Max77663: 0x40daf [0000.812] Entering ramdump check [0000.815] Get RamDumpCarveOut = 0x0 [0000.818] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.824] Last reboot was clean, booting normally! [0000.828] Sdram initialization is successful [0000.832] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.838] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.864] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.889] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.895] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.900] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.905] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.910] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.926] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.931] Platform-DebugCarveout: 0 [0000.934] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.984] Using GPT Primary to query partitions [0000.990] Loading Tboot-CPU binary [0001.039] Verifying bootloader in OdmNonSecureSBK mode [0001.048] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.058] Bootloader downloaded successfully. [0001.062] Downloaded Tboot-CPU binary to 0xa0000258 [0001.067] MAX77620_GPIO1 Configured. [0001.071] MAX77620_GPIO5 Configured. [0001.074] CPU power rail is up [0001.077] CPU clock enabled [0001.081] Performing RAM repair [0001.084] Updating A64 Warmreset Address to 0xa00002e9 [0001.103] Bootloader DTB Load Address: 0x83000000 [0001.120] Kernel DTB Load Address: 0x83080000 [0001.125] Loading cboot binary [0001.219] Verifying bootloader in OdmNonSecureSBK mode [0001.307] Bootloader load address is 0x8010fda8, entry address is 0x80110000 [0001.316] Bootloader downloaded successfully. [0001.320] GPT: Partition NOT found ! [0001.324] Find Partition via GPT Failed [0001.327] function NvTbootGetBinaryOffsets: 0x845208 error [0001.333] Error in NvTbootLoadBinary: 0x845208 ! [0001.337] GPT: Partition NOT found ! [0001.341] No FB partition [0001.343] Next binary entry address: 0x80110000 [0001.347] BoardId: 2595 [0001.353] dram memory type is 3 [0001.358] WB0 init successful [0001.385] Bpmp FW successfully loaded [0001.388] Set NvDecSticky Bits [0001.391] GSC1 address : ff700000 [0001.395] GSC2 address : ff600000 [0001.399] GSC3 address : ff500000 [0001.403] GSC4 address : ff400000 [0001.406] GSC5 address : ff300000 [0001.410] GSC MC Settings done [0001.415] TOS old plaintext Image length 61440 [0001.421] *** Secure OS image signature not verified *** [0001.426] Loading and Validation of Secure OS Successful [0001.431] NvTbootPackSdramParams: start. [0001.436] NvTbootPackSdramParams: done. [0001.440] Tegraboot started after 766241 us [0001.444] Basic modules init took 349313 us [0001.448] Sec Bootdevice Read Time = 202 ms, Read Size = 8459 KB [0001.454] Next stage binary read took 14368 us [0001.458] Carveout took 252743 us [0001.461] CPU initialization took 92313 us [0001.465] Total time taken by TegraBoot 708737 us [0001.470] Starting CPU & Halting co-processor 64b[0001.605] LPDDR4 Training: Number of tables = 10 [0001.609] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.616] EMC Training Successful [0001.619] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.624] EMC Training Successful [0001.628] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.639] EMC Training Successful [0001.642] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.665] EMC Training Successful [0001.668] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.689] EMC Training Successful [0001.692] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.712] EMC Training Successful [0001.715] Switching to 800000 KHz Success [0001.748] LPDDR4 Training: Number of tables = 10 U-Boot 2015.07-rc2-g2ac3917 (Nov 09 2015 - 13:12:08 -0800) TEGRA210 Model: NVIDIA P2371-0000 DRAM: 3 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 2  0 Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0x1d5a000 |/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\|/-\/-\CTRL+C - Operation aborted Tegra210 (P2371-0000) # Tegra210 (P2371-0000) # env set fdt_copy_node_names /cpus:/psci Tegra210 (P2371-0000) # setenv rootpart 1 Tegra210 (P2371-0000) # setenv devtype mmc Tegra210 (P2371-0000) # setenv devnum 0 Tegra210 (P2371-0000) # part uuid ${devtype} ${devnum}:${rootpart} uuid Tegra210 (P2371-0000) # setenv bootargs ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${kernel_addr_r} /boot/Image.defconfig 15667712 bytes read in 811 ms (18.4 MiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${fdt_addr_r} /boot/tegra210-p2371-0000.dtb 45142 bytes read in 460 ms (95.7 KiB/s) Tegra210 (P2371-0000) # load ${devtype} ${devnum}:${rootpart} ${ramdisk_addr_r} /boot/tegra-ramdisk.img 1627787 bytes read in 493 ms (3.1 MiB/s) Tegra210 (P2371-0000) # ramdisk_size=${filesize} Tegra210 (P2371-0000) # booti ${kernel_addr_r} - ${fdt_addr_r} ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 0000000082000000, end 000000008200e055 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.0-rc8-next-20170428-288219-g14cfc5d3 (jonathanh@tamien) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Fri May 5 02:19:29 PDT 2017 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000fe000000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000013fffffff] [ 0.000000] NUMA: Adding memblock [0x80000000 - 0xff1fffff] on node 0 [ 0.000000] NUMA: Adding memblock [0x100000000 - 0x13fffffff] on node 0 [ 0.000000] NUMA: Initmem setup node 0 [mem 0x80000000-0x13fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x13ffacb00-0x13ffae5ff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ff1fffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000013fffffff] [ 0.000000] On node 0 totalpages: 782848 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 520704 pages, LIFO batch:31 [ 0.000000] Normal zone: 4096 pages used for memmap [ 0.000000] Normal zone: 262144 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 24 pages/cpu @ffff8000bff49000 s59904 r8192 d30208 u98304 [ 0.000000] pcpu-alloc: s59904 r8192 d30208 u98304 alloc=24*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] CPU features: enabling workaround for ARM erratum 834220 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 770560 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x70006000 rw root=PARTUUID=00000000-0001-0000-788f-a75600000000 rootwait debug earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] software IO TLB [mem 0xfa000000-0xfe000000] (64MB) mapped at [ffff80007a000000-ffff80007dffffff] [ 0.000000] Memory: 2983360K/3131392K available (8828K kernel code, 1092K rwdata, 4256K rodata, 1088K init, 410K bss, 131648K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB) [ 0.000000] .text : 0xffff000008080000 - 0xffff000008920000 ( 8832 KB) [ 0.000000] .rodata : 0xffff000008920000 - 0xffff000008d50000 ( 4288 KB) [ 0.000000] .init : 0xffff000008d50000 - 0xffff000008e60000 ( 1088 KB) [ 0.000000] .data : 0xffff000008e60000 - 0xffff000008f71200 ( 1093 KB) [ 0.000000] .bss : 0xffff000008f71200 - 0xffff000008fd7b40 ( 411 KB) [ 0.000000] fixed : 0xffff7dfffe7fd000 - 0xffff7dfffec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum) [ 0.000000] 0xffff7e0000000000 - 0xffff7e0003000000 ( 48 MB actual) [ 0.000000] memory : 0xffff800000000000 - 0xffff8000c0000000 ( 3072 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] boot misc1 0x0: expected 0x20 [ 0.000000] (comparison mask = 0xffffff) [ 0.000000] PLL_X already enabled. Postponing set full defaults [ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.008436] Console: colour dummy device 80x25 [ 0.013081] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.023695] pid_max: default: 32768 minimum: 301 [ 0.028547] Security Framework initialized [ 0.035359] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.044121] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.051476] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.058454] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.081920] ASID allocator initialised with 65536 entries [ 0.087577] Hierarchical SRCU implementation. [ 0.101052] Speedo Revision 4 [ 0.104143] Tegra Revision: A01 SKU: 1 CPU Process: -22 SoC Process: -22 [ 0.111952] EFI services will not be available. [ 0.132694] smp: Bringing up secondary CPUs ... [ 0.169534] Detected PIPT I-cache on CPU1 [ 0.169576] CPU1: Booted secondary processor [411fd071] [ 0.201600] Detected PIPT I-cache on CPU2 [ 0.201634] CPU2: Booted secondary processor [411fd071] [ 0.233674] Detected PIPT I-cache on CPU3 [ 0.233706] CPU3: Booted secondary processor [411fd071] [ 0.233772] smp: Brought up 1 node, 4 CPUs [ 0.266689] SMP: Total of 4 processors activated. [ 0.271558] CPU features: detected feature: 32-bit EL0 Support [ 0.277632] CPU: All CPU(s) started at EL2 [ 0.281886] alternatives: patching kernel code [ 0.290595] devtmpfs: initialized [ 0.301571] DMI not present or invalid. [ 0.305729] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.315861] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.322774] pinctrl core: initialized pinctrl subsystem [ 0.329965] NET: Registered protocol family 16 [ 0.354620] Kernel panic - not syncing: rtnetlink_init: cannot initialize rtnetlink [ 0.354620] [ 0.364068] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc8-next-20170428-288219-g14cfc5d3 #1 [ 0.373326] Hardware name: NVIDIA Tegra210 P2371 (P2530/P2595) reference design (DT) [ 0.381328] Call trace: [ 0.383860] [] dump_backtrace+0x0/0x23c [ 0.389443] [] show_stack+0x14/0x1c [ 0.394660] [] dump_stack+0x94/0xb4 [ 0.399884] [] panic+0x12c/0x29c [ 0.404837] [] rtnetlink_init+0x2c/0x1d0 [ 0.410516] [] netlink_proto_init+0x14c/0x17c [ 0.416633] [] do_one_initcall+0x38/0x118 [ 0.422394] [] kernel_init_freeable+0x1a0/0x23c [ 0.428699] [] kernel_init+0x10/0xfc [ 0.434012] [] ret_from_fork+0x10/0x50 [ 0.439503] SMP: stopping secondary CPUs [ 0.443560] ---[ end Kernel panic - not syncing: rtnetlink_init: cannot initialize rtnetlink [ 0.443560]