U-Boot SPL 2015.04-rc3-00209-ga74ef40 (Mar 16 2015 - 14:43:39) U-Boot 2015.04-rc3-00209-ga74ef40 (Mar 16 2015 - 14:43:39) TEGRA20 Model: Compulab TrimSlice board DRAM: 1 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected W25Q80BL with page size 256 Bytes, erase size 4 KiB, total 1 MiB tegra-pcie: PCI regions: tegra-pcie: I/O: 0x82000000-0x82010000 tegra-pcie: non-prefetchable memory: 0xa0000000-0xa8000000 tegra-pcie: prefetchable memory: 0xa8000000-0xc0000000 tegra-pcie: dual-mode configuration tegra-pcie: probing port 0, using 2 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra20 (TrimSlice) # Tegra20 (TrimSlice) # usb reset resetting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found USB1: USB EHCI 1.00 scanning bus 1 for devices... 1 USB Device(s) found USB2: lowlevel init failed scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... Warning: asx0 using MAC address from net device 1 Ethernet Device(s) found Tegra20 (TrimSlice) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=11eb23c1-01 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra20 (TrimSlice) # setenv ipaddr 192.168.100.103; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra20 (TrimSlice) # tftpboot 0x00408000 zImage.multi_v7_defconfig Using RTL8169#0 device TFTP from server 192.168.100.1; our IP address is 192.168.100.103 Filename 'zImage.multi_v7_defconfig'. Load address: 0x408000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 3.5 MiB/s done Bytes transferred = 7852536 (77d1f8 hex) Tegra20 (TrimSlice) # tftpboot 0x02408000 tegra20-trimslice.dtb Using RTL8169#0 device TFTP from server 192.168.100.1; our IP address is 192.168.100.103 Filename 'tegra20-trimslice.dtb'. Load address: 0x2408000 Loading: *## 2.9 MiB/s done Bytes transferred = 21426 (53b2 hex) Tegra20 (TrimSlice) # bootz 0x00408000 - 0x02408000 Kernel image @ 0x408000 [ 0x000000 - 0x77d1f8 ] ## Flattened Device Tree blob at 02408000 Booting using the fdt blob at 0x2408000 Using Device Tree in place at 02408000, end 024103b1 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.0-rc3-next-20170322-160221-gabbb80a (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Thu Mar 23 02:03:55 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [411fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Compulab TrimSlice board [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] free_area_init_node: node 0, pgdat c157bcc0, node_mem_map ef7f8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 17 pages/cpu @ef7c4000 s38528 r8192 d22912 u69632 [ 0.000000] pcpu-alloc: s38528 r8192 d22912 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=11eb23c1-01 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 954408K/1048576K available (10240K kernel code, 1549K rwdata, 4384K rodata, 2048K init, 417K bss, 28632K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc1583710 (1550 kB) [ 0.000000] .bss : 0xc1585000 - 0xc15ed608 ( 418 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 128 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] L2C: platform modifies aux control register: 0x02080000 -> 0x3e480001 [ 0.000000] L2C: DT/platform modifies aux control register: 0x02080000 -> 0x3e480001 [ 0.000000] L2C-310 errata 727915 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310: enabling full line of zeros but not enabled in Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 cache controller enabled, 8 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c4, AUX_CTRL 0x7e480001 [ 0.000010] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000026] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000036] Switching to timer-based delay loop, resolution 1000ns [ 0.001642] Console: colour dummy device 80x30 [ 0.001665] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) [ 0.001677] pid_max: default: 32768 minimum: 301 [ 0.001754] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001765] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002187] CPU: Testing write buffer coherency: ok [ 0.002395] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002624] Setting up static identity map for 0x300000 - 0x300098 [ 0.004047] Tegra Revision: A03 prime SKU: 8 CPU Process: 1 SoC Process: 2 [ 0.004423] EFI services will not be available. [ 0.004593] smp: Bringing up secondary CPUs ... [ 0.005141] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.005205] smp: Brought up 1 node, 2 CPUs [ 0.005217] SMP: Total of 2 processors activated (4.00 BogoMIPS). [ 0.005223] CPU: All CPU(s) started in SVC mode. [ 0.005884] devtmpfs: initialized [ 0.009485] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1 [ 0.009696] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009711] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.012687] pinctrl core: initialized pinctrl subsystem [ 0.013925] NET: Registered protocol family 16 [ 0.015954] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017436] cpuidle: using governor menu [ 0.034642] No ATAGs? [ 0.034709] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.034720] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.039937] Serial: AMBA PL011 UART driver [ 0.051060] AT91: Could not find identification node [ 0.051585] usb1_vbus: Failed to request enable GPIO170: -517 [ 0.051601] reg-fixed-voltage regulators:regulator@2: Failed to register regulator: -517 [ 0.055083] vgaarb: loaded [ 0.055644] SCSI subsystem initialized [ 0.055766] libata version 3.00 loaded. [ 0.055948] usbcore: registered new interface driver usbfs [ 0.055990] usbcore: registered new interface driver hub [ 0.056028] usbcore: registered new device driver usb [ 0.057959] pps_core: LinuxPPS API ver. 1 registered [ 0.057966] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.057983] PTP clock support registered [ 0.058121] EDAC MC: Ver: 3.0.0 [ 0.059870] clocksource: Switched to clocksource timer_us [ 0.098717] NET: Registered protocol family 2 [ 0.099149] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.099220] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.099333] TCP: Hash tables configured (established 8192 bind 8192) [ 0.099449] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.099501] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.099657] NET: Registered protocol family 1 [ 0.099972] RPC: Registered named UNIX socket transport module. [ 0.099981] RPC: Registered udp transport module. [ 0.099986] RPC: Registered tcp transport module. [ 0.099991] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.100000] PCI: CLS 0 bytes, default 64 [ 0.100822] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.102186] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.108629] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.109228] NFS: Registering the id_resolver key type [ 0.109250] Key type id_resolver registered [ 0.109256] Key type id_legacy registered [ 0.109287] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.110528] bounce: pool size: 64 pages [ 0.110567] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.110575] io scheduler noop registered [ 0.110581] io scheduler deadline registered [ 0.110729] io scheduler cfq registered (default) [ 0.110737] io scheduler mq-deadline registered [ 0.121787] tegra-pcie 80003000.pcie-controller: dual-mode configuration [ 0.122490] tegra-pcie 80003000.pcie-controller: probing port 0, using 2 lanes [ 0.206033] tegra-pcie 80003000.pcie-controller: PCI host bridge to bus 0000:00 [ 0.206045] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.206054] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xa7ffffff] [ 0.206063] pci_bus 0000:00: root bus resource [mem 0xa8000000-0xbfffffff pref] [ 0.206071] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.206099] pci 0000:00:01.0: [10de:0bf0] type 01 class 0x060000 [ 0.206126] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 0.206160] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 0.206184] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.206195] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 0.206373] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 0.206385] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 0.206395] pci_bus 0000:00: 1-byte config write to 0000:00:01.0 offset 0xc may corrupt adjacent RW1C bits [ 0.206401] PCI: bus0: Fast back to back transfers disabled [ 0.206411] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.206420] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 0.206430] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 0.206440] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 0.206449] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x6 may corrupt adjacent RW1C bits [ 0.206566] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 0.206590] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 0.206614] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [ 0.206632] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 0.206646] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref] [ 0.206725] pci 0000:01:00.0: supports D1 D2 [ 0.206733] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.229913] PCI: bus1: Fast back to back transfers disabled [ 0.229926] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.229938] Disabling cpuidle LP2 state, since PCIe IRQs are in use [ 0.230000] pci 0000:00:01.0: BAR 8: assigned [mem 0xa0000000-0xa00fffff] [ 0.230012] pci 0000:00:01.0: BAR 9: assigned [mem 0xa8000000-0xa80fffff 64bit pref] [ 0.230021] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff] [ 0.230032] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref] [ 0.230042] pci 0000:01:00.0: BAR 4: assigned [mem 0xa8000000-0xa8003fff 64bit pref] [ 0.230062] pci 0000:01:00.0: BAR 2: assigned [mem 0xa8004000-0xa8004fff 64bit pref] [ 0.230080] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 0.230091] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.230100] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff] [ 0.230108] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xa00fffff] [ 0.230116] pci 0000:00:01.0: bridge window [mem 0xa8000000-0xa80fffff 64bit pref] [ 0.230139] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 0.230188] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 0.230368] pcieport 0000:00:01.0: Signaling PME with IRQ 295 [ 0.236332] tegra-apbdma 6000a000.dma: Tegra20 APB DMA driver register 16 channels [ 0.284857] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.287096] console [ttyS0] disabled [ 0.287132] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 279, base_baud = 13500000) is a Tegra [ 1.342408] console [ttyS0] enabled [ 1.346463] SuperH (H)SCI(F) driver initialized [ 1.351707] msm_serial: driver initialized [ 1.355922] STMicroelectronics ASC driver initialized [ 1.365187] tegra-hdmi 54280000.hdmi: 54280000.hdmi supply hdmi not found, using dummy regulator [ 1.375934] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.382560] [drm] No driver support for vblank timestamp query. [ 1.388493] [drm] Cannot find any crtc or sizes - going 1024x768 [ 1.410707] Console: switching to colour frame buffer device 128x48 [ 1.425382] drm drm: fb0: frame buffer device [ 1.429881] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 [ 1.445164] brd: module loaded [ 1.453849] loop: module loaded [ 1.462734] m25p80 spi32766.0: found s25fl008k, expected w25q80bl [ 1.468822] m25p80 spi32766.0: s25fl008k (1024 Kbytes) [ 1.476150] libphy: Fixed MDIO Bus: probed [ 1.481047] CAN device driver interface [ 1.485525] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.492184] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.498001] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.503972] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.510929] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.517004] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 1.522601] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 1.529230] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xf08fc000, 00:01:c0:13:7d:63, XID 081000c0 IRQ 296 [ 1.538893] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 1.549520] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.556985] usbcore: registered new interface driver pegasus [ 1.562686] usbcore: registered new interface driver asix [ 1.568100] usbcore: registered new interface driver ax88179_178a [ 1.574222] usbcore: registered new interface driver cdc_ether [ 1.580098] usbcore: registered new interface driver smsc75xx [ 1.585877] usbcore: registered new interface driver smsc95xx [ 1.591653] usbcore: registered new interface driver net1080 [ 1.597336] usbcore: registered new interface driver cdc_subset [ 1.603286] usbcore: registered new interface driver zaurus [ 1.608887] usbcore: registered new interface driver cdc_ncm [ 1.614817] tegra-phy c5004000.usb-phy: no vbus regulator [ 1.621309] tegra-phy c5008000.usb-phy: no vbus regulator [ 1.627975] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.634506] ehci-pci: EHCI PCI platform driver [ 1.638973] ehci-platform: EHCI generic platform driver [ 1.644351] ehci-orion: EHCI orion driver [ 1.648463] SPEAr-ehci: EHCI SPEAr driver [ 1.652580] ehci-st: EHCI STMicroelectronics driver [ 1.657542] ehci-exynos: EHCI EXYNOS driver [ 1.661845] ehci-atmel: EHCI Atmel driver [ 1.665948] tegra-ehci: Tegra EHCI driver [ 1.731073] ulpi_phy_power_on: ulpi write failed [ 1.735681] tegra-ehci c5004000.usb: Failed to power on the phy [ 1.741616] tegra-ehci: probe of c5004000.usb failed with error -110 [ 1.750589] tegra-ehci c5008000.usb: EHCI Host Controller [ 1.755993] tegra-ehci c5008000.usb: new USB bus registered, assigned bus number 1 [ 1.763819] tegra-ehci c5008000.usb: irq 290, io mem 0xc5008000 [ 1.789888] tegra-ehci c5008000.usb: USB 2.0 started, EHCI 1.00 [ 1.796420] hub 1-0:1.0: USB hub found [ 1.800203] hub 1-0:1.0: 1 port detected [ 1.804433] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.810624] ohci-pci: OHCI PCI platform driver [ 1.815104] ohci-platform: OHCI generic platform driver [ 1.820491] ohci-omap3: OHCI OMAP3 driver [ 1.824593] SPEAr-ohci: OHCI SPEAr driver [ 1.828692] ohci-st: OHCI STMicroelectronics driver [ 1.833675] ohci-atmel: OHCI Atmel driver [ 1.838263] usbcore: registered new interface driver usb-storage [ 1.846858] rtc-em3027 2-0056: rtc core: registered rtc-em3027 as rtc0 [ 1.854513] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.861681] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.868240] i2c /dev entries driver [ 1.880971] sdhci: Secure Digital Host Controller Interface driver [ 1.887136] sdhci: Copyright(c) Pierre Ossman [ 1.892663] Synopsys Designware Multimedia Card Interface Driver [ 1.899580] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.914099] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.979888] mmc0: SDHCI controller on c8000000.sdhci [c8000000.sdhci] using ADMA [ 1.987367] sdhci-tegra c8000600.sdhci: Got CD GPIO [ 1.992265] sdhci-tegra c8000600.sdhci: Got WP GPIO [ 2.005297] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.069969] mmc1: SDHCI controller on c8000600.sdhci [c8000600.sdhci] using ADMA [ 2.078773] ledtrig-cpu: registered to indicate activity on CPUs [ 2.085060] usbcore: registered new interface driver usbhid [ 2.090635] usbhid: USB HID core driver [ 2.097557] NET: Registered protocol family 10 [ 2.103016] Segment Routing with IPv6 [ 2.106711] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.113142] NET: Registered protocol family 17 [ 2.117580] can: controller area network core (rev 20120528 abi 9) [ 2.123807] NET: Registered protocol family 29 [ 2.128239] can: raw protocol (rev 20120528) [ 2.132511] can: broadcast manager protocol (rev 20161123 t) [ 2.138158] can: netlink gateway (rev 20130117) max_hops=1 [ 2.143953] Key type dns_resolver registered [ 2.148600] ThumbEE CPU extension supported. [ 2.152885] Registering SWP/SWPB emulation handler [ 2.165531] utmi_phy_clk_enable: timeout waiting for phy to stabilize [ 2.169904] usb 1-1: new high-speed USB device number 2 using tegra-ehci [ 2.178692] tegra-ehci c5000000.usb: EHCI Host Controller [ 2.184108] tegra-ehci c5000000.usb: new USB bus registered, assigned bus number 2 [ 2.191975] tegra-ehci c5000000.usb: irq 288, io mem 0xc5000000 [ 2.288883] mmc1: new high speed SD card at address b368 [ 2.294746] mmcblk1: mmc1:b368 NCard 1.83 GiB (ro) [ 2.302238] mmcblk1: p1 p2 [ 2.339913] tegra-ehci c5000000.usb: USB 2.0 started, EHCI 1.00 [ 2.346696] hub 2-0:1.0: USB hub found [ 2.350519] hub 2-0:1.0: 1 port detected [ 2.355681] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.362695] hub 1-1:1.0: USB hub found [ 2.366477] rtc-em3027 2-0056: hctosys: unable to read the hardware clock [ 2.366594] hub 1-1:1.0: 4 ports detected [ 2.378198] Waiting for root device PARTUUID=11eb23c1-01... [ 2.679953] usb 1-1.2: new high-speed USB device number 3 using tegra-ehci [ 3.277784] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.287893] mmc0: new high speed SDHC card at address b368 [ 3.295191] mmcblk0: mmc0:b368 NCard 3.70 GiB [ 3.303629] mmcblk0: p1 [ 3.317043] asix 1-1.2:1.0 eth1: register 'asix' at usb-c5008000.usb-1.2, ASIX AX88772 USB 2.0 Ethernet, 00:60:6e:60:6c:68 [ 3.341318] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.372218] random: fast init done [ 3.588780] EXT4-fs (mmcblk0p1): recovery complete [ 3.662201] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.670408] VFS: Mounted root (ext3 filesystem) on device 179:17. [ 3.680615] devtmpfs: mounted [ 3.689271] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/# root@(none):/# mount -t sysfs none /sys root@(none):/# root@(none):/# mount -t debugfs none /sys/kernel/debug root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:32 1970 [ 15.711526] PM: Syncing filesystems ... done. [ 15.757610] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 15.766071] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 15.775076] Suspending console(s) (use no_console_suspend to debug) [ 15.815232] pci_generic_config_write32: 38 callbacks suppressed [ 15.815277] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x9c may corrupt adjacent RW1C bits [ 15.827676] PM: suspend of devices complete after 43.809 msecs [ 15.832550] PM: late suspend of devices complete after 4.841 msecs [ 15.836454] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x44 may corrupt adjacent RW1C bits [ 15.836511] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x44 may corrupt adjacent RW1C bits [ 15.860551] PM: noirq suspend of devices complete after 27.970 msecs [ 15.860563] Disabling non-boot CPUs ... [ 15.930027] Entering suspend state LP1 [ 15.930027] Suspended for 1.373 seconds [ 15.930074] Enabling non-boot CPUs ... [ 15.959715] CPU1 is up [ 15.960703] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 15.960753] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 15.960782] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x90 may corrupt adjacent RW1C bits [ 15.960812] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x98 may corrupt adjacent RW1C bits [ 15.960839] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x9c may corrupt adjacent RW1C bits [ 15.960919] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 15.960951] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 15.961026] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 15.990136] PM: noirq resume of devices complete after 30.387 msecs [ 15.993592] PM: early resume of devices complete after 2.851 msecs [ 16.539050] PM: resume of devices complete after 545.423 msecs [ 16.707438] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:37 1970 [ 17.274800] PM: Syncing filesystems ... done. [ 17.319945] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 17.328380] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 17.337449] Suspending console(s) (use no_console_suspend to debug) [ 17.387043] PM: suspend of devices complete after 40.835 msecs [ 17.391699] PM: late suspend of devices complete after 4.624 msecs [ 17.420488] PM: noirq suspend of devices complete after 28.756 msecs [ 17.420500] Disabling non-boot CPUs ... [ 17.458652] Entering suspend state LP1 [ 17.458652] Suspended for 3.471 seconds [ 17.458700] Enabling non-boot CPUs ... [ 17.489682] CPU1 is up [ 17.491035] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 17.520051] PM: noirq resume of devices complete after 30.222 msecs [ 17.523585] PM: early resume of devices complete after 2.935 msecs [ 18.058469] PM: resume of devices complete after 534.850 msecs [ 18.123690] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:42 1970 [ 18.804526] PM: Syncing filesystems ... done. [ 18.849605] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 18.858124] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 18.867181] Suspending console(s) (use no_console_suspend to debug) [ 18.917633] PM: suspend of devices complete after 41.795 msecs [ 18.922432] PM: late suspend of devices complete after 4.766 msecs [ 18.950386] PM: noirq suspend of devices complete after 27.921 msecs [ 18.950399] Disabling non-boot CPUs ... [ 18.998473] Entering suspend state LP1 [ 18.998473] Suspended for 3.460 seconds [ 18.998521] Enabling non-boot CPUs ... [ 19.029591] CPU1 is up [ 19.030630] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 19.060099] PM: noirq resume of devices complete after 30.359 msecs [ 19.063662] PM: early resume of devices complete after 2.963 msecs [ 19.608180] PM: resume of devices complete after 544.483 msecs [ 19.673403] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:47 1970 [ 20.344433] PM: Syncing filesystems ... done. [ 20.389487] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 20.398019] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 20.407078] Suspending console(s) (use no_console_suspend to debug) [ 20.457856] PM: suspend of devices complete after 42.115 msecs [ 20.462679] PM: late suspend of devices complete after 4.791 msecs [ 20.490290] PM: noirq suspend of devices complete after 27.576 msecs [ 20.490303] Disabling non-boot CPUs ... [ 20.538369] Entering suspend state LP1 [ 20.538369] Suspended for 3.460 seconds [ 20.538416] Enabling non-boot CPUs ... [ 20.569672] CPU1 is up [ 20.570928] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 20.599884] PM: noirq resume of devices complete after 30.177 msecs [ 20.603634] PM: early resume of devices complete after 2.964 msecs [ 21.148210] PM: resume of devices complete after 544.539 msecs [ 21.213430] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:52 1970 [ 21.884549] PM: Syncing filesystems ... done. [ 21.929710] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 21.938148] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 21.947196] Suspending console(s) (use no_console_suspend to debug) [ 21.984197] pci_generic_config_write32: 90 callbacks suppressed [ 21.984242] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x9c may corrupt adjacent RW1C bits [ 21.996642] PM: suspend of devices complete after 40.759 msecs [ 22.001611] PM: late suspend of devices complete after 4.936 msecs [ 22.006257] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x44 may corrupt adjacent RW1C bits [ 22.006313] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x44 may corrupt adjacent RW1C bits [ 22.030238] PM: noirq suspend of devices complete after 28.594 msecs [ 22.030250] Disabling non-boot CPUs ... [ 22.098455] Entering suspend state LP1 [ 22.098455] Suspended for 3.439 seconds [ 22.098502] Enabling non-boot CPUs ... [ 22.129613] CPU1 is up [ 22.130933] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 22.130983] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 22.131014] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x90 may corrupt adjacent RW1C bits [ 22.131042] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x98 may corrupt adjacent RW1C bits [ 22.131069] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x9c may corrupt adjacent RW1C bits [ 22.131148] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 22.131179] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 22.131252] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 22.159812] PM: noirq resume of devices complete after 30.165 msecs [ 22.163525] PM: early resume of devices complete after 2.932 msecs [ 22.708112] PM: resume of devices complete after 544.552 msecs [ 22.876513] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:00:57 1970 [ 23.444537] PM: Syncing filesystems ... done. [ 23.489742] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 23.498174] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 23.507151] Suspending console(s) (use no_console_suspend to debug) [ 23.557050] PM: suspend of devices complete after 41.204 msecs [ 23.562161] PM: late suspend of devices complete after 5.078 msecs [ 23.590118] PM: noirq suspend of devices complete after 27.924 msecs [ 23.590131] Disabling non-boot CPUs ... [ 23.658187] Entering suspend state LP1 [ 23.658187] Suspended for 3.440 seconds [ 23.658235] Enabling non-boot CPUs ... [ 23.689306] CPU1 is up [ 23.690718] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 23.719850] PM: noirq resume of devices complete after 30.510 msecs [ 23.723336] PM: early resume of devices complete after 2.883 msecs [ 24.268396] PM: resume of devices complete after 545.024 msecs [ 24.333607] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:01:02 1970 [ 24.999796] PM: Syncing filesystems ... done. [ 25.032363] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 25.040733] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 25.049603] Suspending console(s) (use no_console_suspend to debug) [ 25.097062] PM: suspend of devices complete after 39.511 msecs [ 25.101774] PM: late suspend of devices complete after 4.680 msecs [ 25.130058] PM: noirq suspend of devices complete after 28.250 msecs [ 25.130071] Disabling non-boot CPUs ... [ 25.168170] Entering suspend state LP1 [ 25.168170] Suspended for 3.489 seconds [ 25.168219] Enabling non-boot CPUs ... [ 25.199429] CPU1 is up [ 25.200387] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 25.229632] PM: noirq resume of devices complete after 30.168 msecs [ 25.233412] PM: early resume of devices complete after 3.002 msecs [ 25.778144] PM: resume of devices complete after 544.699 msecs [ 25.843487] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:01:07 1970 [ 26.514375] PM: Syncing filesystems ... done. [ 26.559573] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 26.568005] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 26.576974] Suspending console(s) (use no_console_suspend to debug) [ 26.626462] PM: suspend of devices complete after 40.796 msecs [ 26.631170] PM: late suspend of devices complete after 4.675 msecs [ 26.659940] PM: noirq suspend of devices complete after 28.738 msecs [ 26.659953] Disabling non-boot CPUs ... [ 26.728038] Entering suspend state LP1 [ 26.728038] Suspended for 3.440 seconds [ 26.728087] Enabling non-boot CPUs ... [ 26.759153] CPU1 is up [ 26.760594] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 26.789672] PM: noirq resume of devices complete after 30.371 msecs [ 26.793165] PM: early resume of devices complete after 2.890 msecs [ 27.337651] PM: resume of devices complete after 544.452 msecs [ 27.402872] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:01:12 1970 [ 28.074056] PM: Syncing filesystems ... done. [ 28.119122] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 28.127641] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 28.136698] Suspending console(s) (use no_console_suspend to debug) [ 28.175240] pci_generic_config_write32: 90 callbacks suppressed [ 28.175285] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x9c may corrupt adjacent RW1C bits [ 28.187737] PM: suspend of devices complete after 42.374 msecs [ 28.192806] PM: late suspend of devices complete after 5.036 msecs [ 28.197460] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x44 may corrupt adjacent RW1C bits [ 28.197515] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x44 may corrupt adjacent RW1C bits [ 28.219884] PM: noirq suspend of devices complete after 27.047 msecs [ 28.219897] Disabling non-boot CPUs ... [ 28.258035] Entering suspend state LP1 [ 28.258035] Suspended for 3.469 seconds [ 28.258082] Enabling non-boot CPUs ... [ 28.289302] CPU1 is up [ 28.290018] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 28.290066] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 28.290095] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x90 may corrupt adjacent RW1C bits [ 28.290123] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x98 may corrupt adjacent RW1C bits [ 28.290151] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x9c may corrupt adjacent RW1C bits [ 28.290230] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 28.290262] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 28.290336] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 28.319436] PM: noirq resume of devices complete after 30.101 msecs [ 28.322975] PM: early resume of devices complete after 2.941 msecs [ 28.868379] PM: resume of devices complete after 545.370 msecs [ 29.036710] Restarting tasks ... done. root@(none):/# root@(none):/# rtcwake -d rtc1 -m mem -s 3 rtcwake: assuming RTC uses UTC ... rtcwake: wakeup from "mem" using /dev/rtc1 at Thu Jan 1 00:01:17 1970 [ 29.603942] PM: Syncing filesystems ... done. [ 29.649062] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 29.657596] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 29.666660] Suspending console(s) (use no_console_suspend to debug) [ 29.716140] PM: suspend of devices complete after 40.795 msecs [ 29.720832] PM: late suspend of devices complete after 4.657 msecs [ 29.749802] PM: noirq suspend of devices complete after 28.937 msecs [ 29.749815] Disabling non-boot CPUs ... [ 29.787880] Entering suspend state LP1 [ 29.787880] Suspended for 3.470 seconds [ 29.787928] Enabling non-boot CPUs ... [ 29.818928] CPU1 is up [ 29.820397] pcieport 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 29.849489] PM: noirq resume of devices complete after 30.526 msecs [ 29.852993] PM: early resume of devices complete after 2.904 msecs [ 30.387830] PM: resume of devices complete after 534.803 msecs [ 30.453043] Restarting tasks ... done. root@(none):/# root@(none):/# NVTB SYSTEM SUSPEND TEST COMPLETE