U-Boot SPL 2016.05-rc2 (Apr 21 2016 - 16:23:00) Trying to boot from RAM U-Boot 2016.05-rc2 (Apr 21 2016 - 16:23:00 -0700) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB C: Tegra SD/MMC: 0, Tegra SD/MMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # Tegra124 (Jetson TK1) # pci enum Tegra124 (Jetson TK1) # setenv bootargs 'ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash' Tegra124 (Jetson TK1) # setenv ipaddr 192.168.100.102; setenv serverip 192.168.100.1; setenv tftpserverip 192.168.100.1 Tegra124 (Jetson TK1) # tftpboot 0x82000000 zImage.multi_v7_defconfig Warning: eth_rtl8169 using MAC address from ROM Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'zImage.multi_v7_defconfig'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 3.9 MiB/s done Bytes transferred = 7914992 (78c5f0 hex) Tegra124 (Jetson TK1) # tftpboot 0x83000000 tegra124-jetson-tk1.dtb Using eth_rtl8169 device TFTP from server 192.168.100.1; our IP address is 192.168.100.102 Filename 'tegra124-jetson-tk1.dtb'. Load address: 0x83000000 Loading: *##### 3.8 MiB/s done Bytes transferred = 67133 (1063d hex) Tegra124 (Jetson TK1) # bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x78c5f0 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8301363c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.0-rc1-170893-ge99b6f1 (jonathanh@sellafield) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Mon May 15 02:32:32 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] On node 0 totalpages: 524032 [ 0.000000] free_area_init_node: node 0, pgdat c157fd40, node_mem_map eeff8000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 327424 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 17 pages/cpu @eef82000 s39168 r8192 d22272 u69632 [ 0.000000] pcpu-alloc: s39168 r8192 d22272 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: ignore_loglevel console=ttyS0,115200n8 rw root=PARTUUID=b1791faa-84e8-4e27-83a1-9fb0a77e8803 rootwait gpt debug noinitrd earlyprintk init=/bin/bash [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1993420K/2096128K available (10240K kernel code, 1566K rwdata, 4388K rodata, 2048K init, 409K bss, 37172K reserved, 65536K cma-reserved, 1244160K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0d00000 (11232 kB) [ 0.000000] .init : 0xc1200000 - 0xc1400000 (2048 kB) [ 0.000000] .data : 0xc1400000 - 0xc15879b0 (1567 kB) [ 0.000000] .bss : 0xc1590d04 - 0xc15f74d8 ( 410 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 [ 0.000000] Tegra clk 127: register failed with -17 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000027] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000042] Switching to timer-based delay loop, resolution 1000ns [ 0.004885] arch_timer: cp15 timer(s) running at 12.00MHz (virt). [ 0.004904] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns [ 0.004922] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns [ 0.004935] Switching to timer-based delay loop, resolution 83ns [ 0.005400] Console: colour dummy device 80x30 [ 0.005429] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) [ 0.005446] pid_max: default: 32768 minimum: 301 [ 0.005538] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005551] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006043] CPU: Testing write buffer coherency: ok [ 0.006290] /cpus/cpu@0 missing clock-frequency property [ 0.006332] /cpus/cpu@1 missing clock-frequency property [ 0.006373] /cpus/cpu@2 missing clock-frequency property [ 0.006416] /cpus/cpu@3 missing clock-frequency property [ 0.006429] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006714] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.010400] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 [ 0.011125] EFI services will not be available. [ 0.011351] smp: Bringing up secondary CPUs ... [ 0.011943] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015349] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.025362] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.034801] smp: Brought up 1 node, 4 CPUs [ 0.034823] SMP: Total of 4 processors activated (96.00 BogoMIPS). [ 0.034832] CPU: All CPU(s) started in SVC mode. [ 0.036317] devtmpfs: initialized [ 0.052947] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.053345] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.053364] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.054865] pinctrl core: initialized pinctrl subsystem [ 0.056754] NET: Registered protocol family 16 [ 0.058841] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.061275] cpuidle: using governor menu [ 0.087849] No ATAGs? [ 0.087974] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.087990] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.095351] Serial: AMBA PL011 UART driver [ 0.111724] AT91: Could not find identification node [ 0.112284] +5V_SYS: supplied by +VDD_MUX [ 0.112568] +3.3V_SYS: supplied by +VDD_MUX [ 0.113188] +USB0_VBUS_SW: Failed to request enable GPIO108: -517 [ 0.113204] reg-fixed-voltage regulators:regulator@7: Failed to register regulator: -517 [ 0.113304] +5V_USB_HS: Failed to request enable GPIO109: -517 [ 0.113319] reg-fixed-voltage regulators:regulator@8: Failed to register regulator: -517 [ 0.113505] +1.05V_RUN_AVDD_HDMI_PLL: Failed to request enable GPIO63: -517 [ 0.113519] reg-fixed-voltage regulators:regulator@11: Failed to register regulator: -517 [ 0.113617] +5V_HDMI_CON: Failed to request enable GPIO86: -517 [ 0.113631] reg-fixed-voltage regulators:regulator@12: Failed to register regulator: -517 [ 0.113729] +5V_SATA: Failed to request enable GPIO242: -517 [ 0.113742] reg-fixed-voltage regulators:regulator@13: Failed to register regulator: -517 [ 0.113839] +12V_SATA: Failed to request enable GPIO242: -517 [ 0.113852] reg-fixed-voltage regulators:regulator@14: Failed to register regulator: -517 [ 0.116848] vgaarb: loaded [ 0.117629] SCSI subsystem initialized [ 0.117795] libata version 3.00 loaded. [ 0.118037] usbcore: registered new interface driver usbfs [ 0.118097] usbcore: registered new interface driver hub [ 0.118157] usbcore: registered new device driver usb [ 0.121628] pps_core: LinuxPPS API ver. 1 registered [ 0.121639] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.121662] PTP clock support registered [ 0.121852] EDAC MC: Ver: 3.0.0 [ 0.124713] clocksource: Switched to clocksource arch_sys_counter [ 0.179890] NET: Registered protocol family 2 [ 0.180411] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.180512] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.180700] TCP: Hash tables configured (established 8192 bind 8192) [ 0.180783] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.180826] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.180976] NET: Registered protocol family 1 [ 0.181280] RPC: Registered named UNIX socket transport module. [ 0.181290] RPC: Registered udp transport module. [ 0.181299] RPC: Registered tcp transport module. [ 0.181308] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.181320] PCI: CLS 0 bytes, default 64 [ 0.182748] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.184574] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.192996] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.193692] NFS: Registering the id_resolver key type [ 0.193717] Key type id_resolver registered [ 0.193726] Key type id_legacy registered [ 0.193767] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.195472] bounce: pool size: 64 pages [ 0.195514] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.195526] io scheduler noop registered [ 0.195535] io scheduler deadline registered [ 0.195565] io scheduler cfq registered (default) [ 0.195575] io scheduler mq-deadline registered [ 0.195585] io scheduler kyber registered [ 0.201076] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 0.201200] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 0.201669] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517 [ 0.217806] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 0.217863] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 0.224117] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 0.228975] tegra_dma_runtime_resume-1507 [ 0.231985] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.234799] tegra-pmc 7000e400.pmc: emergency thermal reset enabled [ 0.289653] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.292230] console [ttyS0] disabled [ 0.292270] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 335, base_baud = 25500000) is a Tegra [ 1.187301] console [ttyS0] enabled [ 1.191614] SuperH (H)SCI(F) driver initialized [ 1.197154] msm_serial: driver initialized [ 1.201437] STMicroelectronics ASC driver initialized [ 1.207367] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 333, base_baud = 0) is a TEGRA_UART [ 1.216640] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 334, base_baud = 0) is a TEGRA_UART [ 1.230731] tegra-hdmi 54280000.hdmi: failed to get HDMI regulator [ 1.250096] brd: module loaded [ 1.260143] loop: module loaded [ 1.264469] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write [ 1.272815] as3722 4-0040: AS3722 with revision 0x1 found [ 1.284625] as3722-sd2: supplied by +5V_SYS [ 1.289252] as3722-sd3: supplied by +5V_SYS [ 1.293646] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV [ 1.300071] as3722-sd4: supplied by +5V_SYS [ 1.304679] as3722-sd5: supplied by +5V_SYS [ 1.310728] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 1.316802] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV [ 1.323000] as3722-ldo2: supplied by +1.8V_VDDIO [ 1.328904] as3722-ldo3: supplied by +3.3V_SYS [ 1.333379] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV [ 1.341148] as3722-ldo4: supplied by +3.3V_SYS [ 1.345822] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV [ 1.352007] as3722-ldo5: supplied by +1.8V_VDDIO [ 1.356868] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV [ 1.363759] +VDDIO_SDMMC3: bypassed regulator has no supply! [ 1.369432] +VDDIO_SDMMC3: failed to get the current voltage(-517) [ 1.375623] as3722-regulator as3722-regulator: regulator 13 register failed -517 [ 1.388707] tegra-ahci 70027000.sata: couldn't get PHY in node sata: -517 [ 1.400311] spi-tegra114 7000d400.spi: Dma channel is not available: -19 [ 1.407281] spi-tegra114 7000da00.spi: Dma channel is not available: -19 [ 1.415845] libphy: Fixed MDIO Bus: probed [ 1.420975] CAN device driver interface [ 1.425828] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.432851] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.438693] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.444655] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.451621] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.460829] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.468280] usbcore: registered new interface driver pegasus [ 1.473977] usbcore: registered new interface driver asix [ 1.479421] usbcore: registered new interface driver ax88179_178a [ 1.485556] usbcore: registered new interface driver cdc_ether [ 1.491428] usbcore: registered new interface driver smsc75xx [ 1.497238] usbcore: registered new interface driver smsc95xx [ 1.503009] usbcore: registered new interface driver net1080 [ 1.508711] usbcore: registered new interface driver cdc_subset [ 1.514654] usbcore: registered new interface driver zaurus [ 1.520288] usbcore: registered new interface driver cdc_ncm [ 1.526181] tegra-phy 7d004000.usb-phy: no vbus regulator [ 1.533606] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.540145] ehci-pci: EHCI PCI platform driver [ 1.544621] ehci-platform: EHCI generic platform driver [ 1.550065] ehci-orion: EHCI orion driver [ 1.554232] SPEAr-ehci: EHCI SPEAr driver [ 1.558401] ehci-st: EHCI STMicroelectronics driver [ 1.563413] ehci-exynos: EHCI EXYNOS driver [ 1.567770] ehci-atmel: EHCI Atmel driver [ 1.571912] tegra-ehci: Tegra EHCI driver [ 1.578766] tegra-ehci 7d004000.usb: EHCI Host Controller [ 1.584180] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 [ 1.592138] tegra-ehci 7d004000.usb: irq 354, io mem 0x7d004000 [ 1.624737] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 [ 1.631402] hub 1-0:1.0: USB hub found [ 1.635206] hub 1-0:1.0: 1 port detected [ 1.639673] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.645873] ohci-pci: OHCI PCI platform driver [ 1.650357] ohci-platform: OHCI generic platform driver [ 1.655762] ohci-omap3: OHCI OMAP3 driver [ 1.659910] SPEAr-ohci: OHCI SPEAr driver [ 1.664058] ohci-st: OHCI STMicroelectronics driver [ 1.669085] ohci-atmel: OHCI Atmel driver [ 1.673872] usbcore: registered new interface driver usb-storage [ 1.684314] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 [ 1.691207] as3722-rtc as3722-rtc: RTC interrupt 377 [ 1.699475] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.706662] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.713374] i2c /dev entries driver [ 1.723615] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator [ 1.740813] sdhci: Secure Digital Host Controller Interface driver [ 1.747012] sdhci: Copyright(c) Pierre Ossman [ 1.752980] Synopsys Designware Multimedia Card Interface Driver [ 1.760321] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.766770] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 1.771658] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 1.792921] mmc0: Unknown controller version (3). You may experience problems. [ 1.800193] mmc0: Invalid maximum block size, assuming 512 bytes [ 1.864735] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA [ 1.874064] ledtrig-cpu: registered to indicate activity on CPUs [ 1.880458] usbcore: registered new interface driver usbhid [ 1.886043] usbhid: USB HID core driver [ 1.893823] NET: Registered protocol family 10 [ 1.899198] Segment Routing with IPv6 [ 1.902912] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.909445] NET: Registered protocol family 17 [ 1.913894] can: controller area network core (rev 20170425 abi 9) [ 1.920140] NET: Registered protocol family 29 [ 1.924580] can: raw protocol (rev 20170425) [ 1.928863] can: broadcast manager protocol (rev 20170425 t) [ 1.934520] can: netlink gateway (rev 20170425) max_hops=1 [ 1.940334] Key type dns_resolver registered [ 1.945220] ThumbEE CPU extension supported. [ 1.949491] Registering SWP/SWPB emulation handler [ 1.968316] +3.3V_RUN: supplied by +3.3V_SYS [ 1.973777] +USB0_VBUS_SW: supplied by +5V_SYS [ 1.978490] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN [ 1.984413] +5V_USB_HS: supplied by +5V_SYS [ 1.990373] +3.3V_LP0: supplied by +3.3V_SYS [ 1.996918] +5V_HDMI_CON: supplied by +5V_SYS [ 2.001925] +5V_SATA: supplied by +5V_SYS [ 2.006615] +12V_SATA: supplied by +VDD_MUX [ 2.012266] mmc0: new high speed MMC card at address 0001 [ 2.012672] usb2-0: usb2-0 supply vbus not found, using dummy regulator [ 2.012817] usb2-1: usb2-1 supply vbus not found, using dummy regulator [ 2.013150] usb3-0: usb3-0 supply vbus not found, using dummy regulator [ 2.014470] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.014523] tegra-pcie 1003000.pcie-controller: Failed to get supply 'avddio-pex': -517 [ 2.018525] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator [ 2.023926] tegra-hdmi 54280000.hdmi: failed to get PLL regulator [ 2.066405] mmcblk0: mmc0:0001 SEM16G 14.7 GiB [ 2.071572] as3722-sd2: supplied by +5V_SYS [ 2.076202] as3722-sd3: supplied by +5V_SYS [ 2.080684] as3722-sd4: supplied by +5V_SYS [ 2.085076] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB [ 2.085306] as3722-sd5: supplied by +5V_SYS [ 2.095971] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB [ 2.096526] as3722-ldo0: supplied by +1.35V_LP0(sd2) [ 2.107127] as3722-ldo1: supplied by +3.3V_RUN [ 2.107285] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 2.110337] mmcblk0: p1 [ 2.120330] as3722-ldo2: supplied by +1.8V_VDDIO [ 2.125981] as3722-ldo3: supplied by +3.3V_SYS [ 2.131280] as3722-ldo4: supplied by +3.3V_SYS [ 2.136081] as3722-ldo5: supplied by +1.8V_VDDIO [ 2.140951] as3722-ldo6: supplied by +3.3V_RUN [ 2.145753] as3722-ldo7: supplied by +1.8V_VDDIO [ 2.151130] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV [ 2.158223] as3722-ldo9: supplied by +5V_SYS [ 2.163781] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV [ 2.170361] as3722-ldo10: supplied by +5V_SYS [ 2.175268] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV [ 2.182067] as3722-ldo11: supplied by +3.3V_RUN [ 2.187405] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV [ 2.196978] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 2.206043] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pio slum part sadm sds apst [ 2.216524] scsi host0: tegra-ahci [ 2.221085] scsi host1: tegra-ahci [ 2.224813] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 345 [ 2.232806] ata2: DUMMY [ 2.238139] tegra-ehci 7d008000.usb: EHCI Host Controller [ 2.243553] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 [ 2.251369] tegra-ehci 7d008000.usb: irq 355, io mem 0x7d008000 [ 2.284833] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 [ 2.291836] hub 2-0:1.0: USB hub found [ 2.295695] hub 2-0:1.0: 1 port detected [ 2.302005] sdhci-tegra 700b0400.sdhci: Got CD GPIO [ 2.306956] sdhci-tegra 700b0400.sdhci: Got WP GPIO [ 2.318936] mmc1: Unknown controller version (3). You may experience problems. [ 2.326272] mmc1: Invalid maximum block size, assuming 512 bytes [ 2.395254] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA [ 2.403351] tegra-pcie 1003000.pcie-controller: 2x1, 1x1 configuration [ 2.413147] tegra-pcie 1003000.pcie-controller: probing port 0, using 2 lanes [ 2.422514] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000008 [ 2.430979] random: fast init done [ 2.446903] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 2.456204] tegra-pcie 1003000.pcie-controller: Slot present pin change, signature: 00000000 [ 2.470983] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.478253] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.484439] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.491349] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.498702] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.504229] pci 0000:00:01.0: [10de:0e12] type 01 class 0x060400 [ 2.510327] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.520124] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.529947] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.536608] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.546658] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 [ 2.552718] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits [ 2.562517] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits [ 2.572340] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.578316] ata1: SATA link down (SStatus 0 SControl 300) [ 2.584397] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits [ 2.594438] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.604190] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x3e may corrupt adjacent RW1C bits [ 2.613935] pci_bus 0000:00: 2-byte config write to 0000:00:01.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.623592] pci_bus 0000:00: 1-byte config write to 0000:00:01.0 offset 0xc may corrupt adjacent RW1C bits [ 2.633250] PCI: bus0: Fast back to back transfers disabled [ 2.638838] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.646892] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.655152] pci 0000:01:00.0: [8086:4232] type 00 class 0x028000 [ 2.661209] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.668231] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.689402] mmc1: new high speed SDHC card at address aaaa [ 2.695408] PCI: bus1: Fast back to back transfers disabled [ 2.700992] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.707883] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 2.713926] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.719576] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.726446] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.733817] pci 0000:02:00.0: supports D1 D2 [ 2.738129] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.745614] mmcblk1: mmc1:aaaa SD04G 3.69 GiB [ 2.763568] mmcblk1: p1 p2 p3 [ 2.774882] PCI: bus2: Fast back to back transfers disabled [ 2.780471] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.787283] pci 0000:00:01.0: BAR 8: assigned [mem 0x13000000-0x130fffff] [ 2.794067] pci 0000:00:02.0: BAR 8: assigned [mem 0x13100000-0x131fffff] [ 2.800893] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.808650] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] [ 2.814766] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 2.822107] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.827110] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 2.833905] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.841703] pci 0000:02:00.0: BAR 2: assigned [mem 0x13100000-0x13100fff 64bit] [ 2.849044] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.855176] pci 0000:00:02.0: PCI bridge to [bus 02] [ 2.860141] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.866250] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 2.873033] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.880837] pci 0000:00:01.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.887920] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.894243] pcieport 0000:00:01.0: Signaling PME with IRQ 393 [ 2.900139] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge [ 2.907207] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.913534] pcieport 0000:00:02.0: Signaling PME with IRQ 394 [ 2.919624] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.925238] r8169 0000:02:00.0: enabling device (0140 -> 0143) [ 2.956391] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xf0b5e000, 00:04:4b:3a:d9:81, XID 0c000800 IRQ 395 [ 2.966080] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 2.978868] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN [ 2.986850] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 2.994944] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz [ 3.002260] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz [ 3.011395] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.018784] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:02:04 UTC (946684924) [ 3.027759] +3.3V_AVDD_HDMI_AP_GATED: disabling [ 3.032280] +USB0_VBUS_SW: disabling [ 3.035879] +1.05V_RUN_AVDD_HDMI_PLL: disabling [ 3.040406] +5V_HDMI_CON: disabling [ 3.043893] +1.8V_RUN_CAM: disabling [ 3.047741] +2.8V_RUN_CAM: disabling [ 3.051528] +1.2V_RUN_CAM_FRONT: disabling [ 3.055915] +1.05V_RUN_CAM_REAR: disabling [ 3.060169] +3.3V_RUN_TOUCH: disabling [ 3.064075] +2.8V_RUN_CAM_AF: disabling [ 3.068154] +1.8V_RUN_VPP_FUSE: disabling [ 3.073251] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 3.115082] EXT4-fs (mmcblk0p1): recovery complete [ 3.120712] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.128842] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.138944] devtmpfs: mounted [ 3.142725] Freeing unused kernel memory: 2048K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#